RESUMO
The surface tension of a molten sample can be evaluated based on its resonant frequency with various levitation techniques. Under a 1-G condition, the use of levitation forces to counteract gravity will cause the levitated sample's resonant frequency to differ from that under microgravity. A mathematical relationship to correct for this deviation is not available for a sample levitated with aerodynamic levitation (ADL), which raises issues on the validity of surface tension measurements done with ADL. In this study, we compared the surface tension of molten Al2O3 obtained using the front tracking (FT) simulation method, the drop-bounce method with ADL, and the oscillating drop method with ADL. The drop-bounce method simulates microgravity by allowing the sample to free-fall over a period of tens of milliseconds. Based on the results of this comparison, we determined that the surface tension of molten materials measured with ground-based ADL with the oscillating drop method, calculated using the resonant frequency of the l=2 m=0 mode, only shows a small deviation from that obtained under microgravity.
RESUMO
Until now, heat capacity measurements performed with levitation techniques have required accurate knowledge of the sample's emissivity beforehand. For a sample levitated using an aerodynamic levitator, it experiences both radiative and forced convective heat loss. The sample's emissivity only allows for the calculation of the radiative heat loss term, and a model has yet to be developed to accurately describe the total combined heat loss for aerodynamic levitation (ADL). In this study, we will introduce a novel multiple-gas cooling method for heat capacity measurement for ADL where two types of inert levitation gases (Ar and Kr) with different thermal conductivities were used to generate two cooling curves for the same sample. For samples being cooled at different cooling rates, the total heat loss is the same. The radiative heat loss was expressed using Stefan-Boltzmann's law, and the convective heat loss using Ranz-Marshall's equation. The two independent parameters (i.e., emissivity and heat capacity) of one given sample could then be solved using the two independent cooling curves. The heat capacities of gold, copper, nickel, iron, and palladium around the melting point were measured using this method. The multiple-gas cooling method for heat capacity measurement introduced in this study is the first heat capacity measurement method available for ADL and can be performed for materials with unknown emissivity. This newly developed method is important for the study of the thermophysical properties of high-temperature liquids, especially molten oxides with low electrical conductivity.
RESUMO
Liquid ZrO2 is one of the most important materials involved in severe accident analysis of a light-water reactor. Despite its importance, the physical properties of liquid ZrO2 are scarcely reported. In particular, there are no experimental reports on the viscosity of liquid ZrO2. This is mainly due to the technical difficulties involved in the measurement of thermo-physical properties of liquid ZrO2, which has an extremely high melting point. To address this problem, an aerodynamic levitation technique was used in this study. The density of liquid ZrO2 was calculated from its mass and volume, estimated based on the recorded image of the sample. The viscosity was measured by a droplet oscillation technique. The density and viscosity of liquid ZrO2 at temperatures ranging from 2753 K to 3273 K, and 3170 K-3471 K, respectively, were successfully evaluated. The density of liquid ZrO2 was found to be 4.7 g/cm 3 at its melting point of 2988 K and decreased linearly with increasing temperature, and the viscosity of liquid ZrO2 was 13 mPa at its melting point.
RESUMO
Ternary compounds with a tetragonal chalcopyrite structure, such as CuGaTe2, are promising thermoelectric (TE) materials. It has been demonstrated in various chalcopyrite systems, including compounds with quaternary chalcopyrite-like structures, that the lattice parameter ratio, c/ a, being exactly 2.00 to have a pseudo-cubic structure is key to increase the degeneracy at the valence band edge and ultimately achieve high TE performance. Considering the fact that ZnSnSb2 with a chalcopyrite structure is reported to have c/ a close to 2.00, it is expected to have multiple valence bands leading to a high p-type zT. However, there are no complete investigations on the high temperature TE properties of ZnSnSb2 mainly because of the difficulty of obtaining a single-phase ZnSnSb2. In the present study, pure ZnSnSb2 samples with no impurities are synthesized successfully using a Sn flux-based method and TE properties are characterized up to 585 K. Transport properties and thermal analysis indicate that the structure of ZnSnSb2 remains chalcopyrite with no order-disorder transition and clearly show that ZnSnSb2 can be made to exhibit a high zT in the low-to-mid temperature range through further optimization.
RESUMO
In March 2011, the Fukushima Daiichi Nuclear Power Plant accident caused nuclear fuel to melt and the release of high-volatility fission products into the environment. Caesium and iodine caused environmental contamination and public exposure. Certain fission-product behaviours remain unclear. We found experimentally that liquid CsI disperses extremely favourably toward solid UO2, exhibiting a contact angle approaching zero. We further observed the presence of CsI several tens of micrometres below the surface of the solid UO2 sample, which would be caused by the infiltration of pores network by liquid CsI. Thus, volatile fission products released from molten nuclear fuels with complex internal composition and external structure migrate or evaporate to varying extents, depending on the nature of the solid-liquid interface and the fuel material surface, which becomes the pathway for the released fission products. Introducing the concept of the wettability of liquid chemical species of fission products in contact with solid fuels enabled developing accurate behavioural assessments of volatile fission products released by nuclear fuel.
RESUMO
The high-temperature thermoelectric properties of thallium (Tl) and potassium (K) double-filled cobalt antimonide (CoSb3)-based skutterudites with nominal compositions TlxK0.3Co4Sb12 (x = 0.1 - 0.3) were investigated. The filling fraction of Tl in CoSb3 was enhanced by co-filling with K, which resulted in all of the samples showing the filled-skutterudite single phase. Owing to the high filling ratio, the carrier concentration in the sample with x = 0.3 was as high as 4.3 × 10(20) cm(-3) at room temperature. Furthermore, quite low lattice thermal conductivity (as low as 0.9 Wm(-1)K(-1)) was obtained for the sample with x = 0.3, probably because of strong phonon scattering by the Tl and K co-rattling effect, which resulted in a maximum zT of around one at 773 K.
RESUMO
The effectiveness of thermoelectric (TE) materials is quantified by the dimensionless figure of merit (zT). An ideal way to enhance zT is by scattering phonons without scattering electrons. Here we show that, using a simple bottom-up method, we can prepare bulk nanostructured Si that exhibits an exceptionally high zT of 0.6 at 1050 K, at least three times higher than that of the optimized bulk Si. The nanoscale precipitates in this material connected coherently or semi-coherently with the Si matrix, effectively scattering heat-carrying phonons without significantly influencing the material's electron transport properties, leading to the high zT.
RESUMO
CuGaTe(2) with a chalcopyrite structure demonstrates promising thermoelectric properties. The maximum figure of merit ZT is 1.4 at 950 K. CuGaTe(2) and related chalcopyrites are a new class of high-efficiency bulk thermoelectric material for high-temperature applications.