A nationwide study of air pollution from particulate matter and daily hospitalizations for respiratory diseases in Italy.

BACKGROUND/AIM: The relationship between air pollution and respiratory morbidity has been widely addressed in urban and metropolitan areas but little is known about the effects in non-urban settings. Our aim was to assess the short-term effects of PM10 and PM2.5 on respiratory admissions in the whole country of Italy during 2006-2015. METHODS: We estimated daily PM concentrations at the municipality level using satellite data and spatiotemporal predictors. We collected daily counts of respiratory hospital admissions for each Italian municipality. We considered five different outcomes: all respiratory diseases, asthma, chronic obstructive pulmonary disease (COPD), lower and upper respiratory tract infections (LRTI and URTI). Meta-analysis of province-specific estimates obtained by time-series models, adjusting for temperature, humidity and other confounders, was applied to extrapolate national estimates for each outcome. At last, we tested for effect modification by sex, age, period, and urbanization score. Analyses for PM2.5 were restricted to 2013-2015 cause the goodness of fit of exposure estimation. RESULTS: A total of 4,154,887 respiratory admission were registered during 2006-2015, of which 29% for LRTI, 12% for COPD, 6% for URTI, and 3% for asthma. Daily mean PM10 and PM2.5 concentrations over the study period were 23.3 and 17 µg/m3, respectively. For each 10 µg/m3 increases in PM10 and PM2.5 at lag 0-5 days, we found excess risks of total respiratory diseases equal to 1.20% (95% confidence intervals, 0.92, 1.49) and 1.22% (0.76, 1.68), respectively. The effects for the specific diseases were similar, with the strongest ones for asthma and COPD. Higher effects were found in the elderly and in less urbanized areas. CONCLUSIONS: Short-term exposure to PM is harmful for the respiratory system throughout an entire country, especially in elderly patients. Strong effects can be found also in less urbanized areas.

Thermo-Mechanical and Morphological Properties of Polymer Composites Reinforced by Natural Fibers Derived from Wet Blue Leather Wastes: A Comparative Study.

The present work investigated the possibility to use wet blue (WB) leather wastes as natural reinforcing fibers within different polymer matrices. After their preparation and characterization, WB fibers were melt-mixed at 10 wt.% with poly(lactic acid) (PLA), polyamide 12 (PA12), thermoplastic elastomer (TPE), and thermoplastic polyurethane (TPU), and the obtained samples were subjected to rheological, thermal, thermo-mechanical, and viscoelastic analyses. In parallel, morphological properties such as fiber distribution and dispersion, fiber-matrix adhesion, and fiber exfoliation phenomena were analyzed through a scanning electron microscope (SEM) and energy-dispersive spectroscopy (EDS) to evaluate the relationship between the compounding process, mechanical responses, and morphological parameters. The PLA-based composite exhibited the best results since the Young modulus (+18%), tensile strength (+1.5%), impact (+10%), and creep (+5%) resistance were simultaneously enhanced by the addition of WB fibers, which were well dispersed and distributed in and significantly branched and interlocked with the polymer matrix. PA12- and TPU-based formulations showed a positive behavior (around +47% of the Young modulus and +40% of creep resistance) even if the not-optimal fiber-matrix adhesion and/or the poor de-fibration of WB slightly lowered the tensile strength and elongation at break. Finally, the TPE-based sample exhibited the worst performance because of the poor affinity between hydrophilic WB fibers and the hydrophobic polymer matrix.

Functionalization and use of grape stalks as poly(butylene succinate) (PBS) reinforcing fillers.

Grape stalks are a lignocellulosic biomass, which is a very complex material, whose easy and profitable fractionation to obtain its basic components is still not available. Therefore, alternative ways to try and make use of grape stalks are currently being explored. In the present study, the possible use of dried and milled grape stalks as filler in bio-composites was assessed using polybutylene succinate as a basic polymer. The tensile specimens produced using 10% grape stalk powder as it is and functionalized through pre-extrusion acetylation and silylation, and silylation in situ were characterized for their structural, mechanical, thermal, morphological, and color properties. The bio-composites showed to be stiffer than the control polymer, with an increase of Young's modulus from 616 MPa to 732 MPa in the specimens obtained with acetylated grape stalk powder. This led to a potentially new method to valorize by-products of the wine industry such as grape stalks in order to recover raw materials which could prove useful in the biomaterials and bio-composites sector.

Wine By-Products as Raw Materials for the Production of Biopolymers and of Natural Reinforcing Fillers: A Critical Review.

The plastic industry is today facing a green revolution; however, biopolymers, produced in low amounts, expensive, and food competitive do not represent an efficient solution. The use of wine waste as second-generation feedstock for the synthesis of polymer building blocks or as reinforcing fillers could represent a solution to reduce biopolymer costs and to boost the biopolymer presence in the market. The present critical review reports the state of the art of the scientific studies concerning the use of wine by-products as substrate for the synthesis of polymer building blocks and as reinforcing fillers for polymers. The review has been mainly focused on the most used bio-based and biodegradable polymers present in the market (i.e., poly(lactic acid), poly(butylene succinate), and poly(hydroxyalkanoates)). The results present in the literature have been reviewed and elaborated in order to suggest new possibilities of development based on the chemical and physical characteristics of wine by-products.

Recycling of Chrome-Tanned Leather and Its Utilization as Polymeric Materials and in Polymer-Based Composites: A Review.

Tanneries generate large amounts of solid and liquid wastes, which contain harmful chemical compounds in the environment, such as chromium, that is used in the tanning process. Until now, they have been almost completely dumped in landfills. Thus, finding eco-sustainable and innovative alternatives for the management and disposal of these wastes is becoming a huge challenge for tanneries and researchers around the world. In particular, the scientific and industrial communities have started using wastes to produce new materials exploiting the characteristics of leather, which are strongly connected with the macromolecular structure of its main component, collagen. None of the reviews on leather waste management actually present in the scientific literature report in detail the use of leather to make composite materials and the mechanical properties of the materials obtained, which are of fundamental importance for an effective industrial exploitation of leather scraps. This comprehensive review reports for the first time the state of the art of the strategies related to the recovery and valorization of both hydrolyzed collagen and leather waste for the realization of composite materials, reporting in detail the properties and the industrial applications of the materials obtained. In the conclusion section, the authors provide practical implications for industry in relation to sustainability and identify research gaps that can guide future authors and industries in their work.