RESUMO
Solution-processable poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) is an important polymeric conductor used extensively in organic flexible, wearable, and stretchable optoelectronics. However, further enhancing its conductivity and long-term stability while maintaining its superb mechanical properties remains challenging. Here, a novel post-treatment approach to enhance the electrical properties and stability of sub-20-nm-thin PEDOT:PSS films processed from solution is introduced. The approach involves a sequential post-treatment with HNO3 and CsCl, resulting in a remarkable enhancement of the electrical conductivity of PEDOT:PSS films to over 5500 S cm-1, along with improved carrier mobility. The post-treated films exhibit remarkable air stability, retaining over 85% of their initial conductivity even after 270 days of storage. Various characterization techniques, including X-ray photoelectron spectroscopy, atomic force microscopy, Raman spectroscopy, Hall effect measurements, and grazing incidence wide angle X-ray scattering, coupled with density functional theory calculations, provide insights into the structural changes and interactions responsible for these improvements. To demonstrate the potential for practical applications, the ultrathin PEDOT:PSS films are connected to an inorganic light-emitting diode with a battery, showcasing their suitability as transparent electrodes. This work presents a promising approach for enhancing the electrical conductivity of PEDOT:PSS while offering a comprehensive understanding of the underlying mechanisms that can guide further advances.
RESUMO
Cyclophosphazenes offer a robust and easily modifiable platform for a diverse range of functional systems that have found applications in a wide variety of areas. Herein, for the first time, it reports an organophosphazene-based supramolecular ferroelectric [(PhCH2 NH)6 P3 N3 Me]I, [PMe]I. The compound crystallizes in the polar space group Pc and its thin-film sample exhibits remnant polarization of 5 µC cm-2 . Vector piezoresponse force microscopy (PFM) measurements indicated the presence of multiaxial polarization. Subsequently, flexible composites of [PMe]I are fabricated for piezoelectric energy harvesting applications using thermoplastic polyurethane (TPU) as the matrix. The highest open-circuit voltages of 13.7 V and the maximum power density of 34.60 µW cm-2 are recorded for the poled 20 wt.% [PMe]I/TPU device. To understand the molecular origins of the high performance of [PMe]I-based mechanical energy harvesting devices, piezoelectric charge tensor values are obtained from DFT calculations of the single crystal structure. These indicate that the mechanical stress-induced distortions in the [PMe]I crystals are facilitated by the high flexibility of the layered supramolecular assembly.
RESUMO
Three-dimensional printing (3DP) is an emerging technology to fabricate complex architectures, necessary to realize state-of-the-art flexible and wearable electronic devices. In this regard, top-performing devices containing organic ferro- and piezoelectric compounds are desired to circumvent significant shortcomings of conventional piezoceramics, e.g. toxicity and high-temperature device processibility. Herein, we report on a 3D-printed composite of a chiral ferroelectric organic salt {[Me3CCH(Me)NH3][BF4]} (1) with a biodegradable polycaprolactone (PCL) polymer that serves as a highly efficient piezoelectric nanogenerator (PENG). The ferroelectric property of 1 originates from its polar tetragonal space group P42, verified by P-E loop measurements. The ferroelectric domain characteristics of 1 were further probed by piezoresponse force microscopy (PFM), which gave characteristic 'butterfly' and hysteresis loops. The PFM amplitude vs. drive voltage measurements gave a relatively high magnitude of the converse piezoelectric coefficient for 1. PCL polymer composites with various weight percentages (wt%) of 1 were prepared and subjected to piezoelectric energy harvesting tests, which gave a maximum open-circuit voltage of 36.2 V and a power density of 48.1 µW cm-2 for the 10 wt% 1-PCL champion device. Furthermore, a gyroid-shaped 3D-printed 10 wt% 1-PCL composite was fabricated to test its practical utility, which gave an excellent output voltage of 41 V and a power density of 56.8 µW cm-2. These studies promise the potential of simple organic compounds for building PENG devices using advanced manufacturing technologies.
RESUMO
The ferroelectric behaviour of an octahedral cage [[Ni6(H2O)12(TPTA)8]·(NO3)12·36H2O] (1) exhibiting high remnant polarization of 25.31 µC cm-2 is discovered. For the first time, clear domain structures and the characteristic electromechanical responses are demonstrated using piezoresponsive force microscopy for a thin film of 1. Owing to its mechanical energy conversion capability, polymer composites of 1 were employed as efficient piezoelectric nanogenerators.
RESUMO
Bismuth containing hybrid molecular ferroelectrics are receiving tremendous attention in recent years owing to their stable and non-toxic composition. However, these perovskite-like structures are primarily limited to ammonium cations. Herein, we report a new phosphonium based discrete perovskite-like hybrid ferroelectric with a formula [Me(Ph)3 P]3 [Bi2 Br9 ] (MTPBB) and its mechanical energy harvesting capability. The Polarization-Electric field (P-E) measurements resulted in a well-defined ferroelectric hysteresis loop with a remnant polarization value of 2.1â µC cm-2 . Piezoresponse force microscopy experiments enabled visualization of the ferroelectric domain structure and evaluation of the piezoelectric strain coefficient (d33 ) for an MTPBB single crystal and thin film sample. Furthermore, flexible devices incorporating MTPBB in polydimethylsiloxane (PDMS) matrix at various concentrations were fabricated and explored for their mechanical energy harvesting properties. The champion device with 20â wt % of MTPBB in PDMS rendered a maximum peak-to-peak open-circuit voltage of 22.9â V and a maximum power density of 7â µW cm-2 at an optimal load of 4â MΩ. Moreover, the potential of MTPBB-based devices in low power electronics was demonstrated by storing the harvested energy in various electrolytic capacitors.
RESUMO
The low carrier mobility of organic semiconductors and the high parasitic resistance and capacitance often encountered in conventional organic Schottky diodes hinder their deployment in emerging radio frequency (RF) electronics. Here, these limitations are overcome by combining self-aligned asymmetric nanogap electrodes (≈25 nm) produced by adhesion lithography, with a high mobility organic semiconductor, and RF Schottky diodes able to operate in the 5G frequency spectrum are demonstrated. C16 IDT-BT is used, as the high hole mobility polymer, and the impact of p-doping on the diode performance is studied. Pristine C16 IDT-BT-based diodes exhibit maximum intrinsic and extrinsic cutoff frequencies (fC ) of >100 and 6 GHz, respectively. This extraordinary performance is attributed to the planar nature of the nanogap channel and the diode's small junction capacitance (<2 pF). Doping of C16 IDT-BT with the molecular p-dopant C60 F48 improves the diode's performance further by reducing the series resistance resulting to intrinsic and extrinsic fC of >100 and ≈14 GHz respectively, while the DC output voltage of an RF rectifier circuit increases by a tenfold. Our work highlights the importance of the planar nanogap architecture and paves the way for the use of organic Schottky diodes in large-area RF electronics of the future.
RESUMO
Self-assembled monolayers (SAMs) based on Br-2PACz ([2-(3,6-dibromo-9H-carbazol-9-yl)ethyl]phosphonic acid) 2PACz ([2-(9H-Carbazol-9-yl)ethyl]phosphonic acid) and MeO-2PACz ([2-(3,6-dimethoxy-9H-carbazol-9-yl)ethyl]phosphonic acid) molecules were investigated as hole-extracting interlayers in organic photovoltaics (OPVs). The highest occupied molecular orbital (HOMO) energies of these SAMs were measured at -6.01 and -5.30â eV for Br-2PACz and MeO-2PACz, respectively, and found to induce significant changes in the work function (WF) of indium-tin-oxide (ITO) electrodes upon chemical functionalization. OPV cells based on PM6 (poly[(2,6-(4,8-bis(5-(2-ethylhexyl-3-fluoro)thiophen-2-yl)-benzo[1,2-b:4,5-b']dithiophene))-alt-(5,5-(1',3'-di-2-thienyl-5',7'-bis(2-ethylhexyl)benzo[1',2'-c:4',5'-c']dithiophene-4,8-dione)]) : BTP-eC9 : PC71 BM ([6,6]-phenyl-C71-butyric acid methyl ester) using ITO/Br-2PACz anodes exhibited a maximum power conversion efficiency (PCE) of 18.4 %, outperforming devices with ITO/MeO-2PACz (14.5 %) and ITO/poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT : PSS) (17.5 %). The higher PCE was found to originate from the much higher WF of ITO/Br-2PACz (-5.81â eV) compared to ITO/MeO-2PACz (4.58â eV) and ITO/PEDOT : PSS (4.9â eV), resulting in lower interface resistance, improved hole transport/extraction, lower trap-assisted recombination, and longer carrier lifetimes. Importantly, the ITO/Br-2PACz electrode was chemically stable, and after removal of the SAM it could be recycled and reused to construct fresh OPVs with equally impressive performance.
RESUMO
Controlling the morphology of metal halide perovskite layers during processing is critical for the manufacturing of optoelectronics. Here, a strategy to control the microstructure of solution-processed layered Ruddlesden-Popper-phase perovskite films based on phenethylammonium lead bromide ((PEA)2 PbBr4 ) is reported. The method relies on the addition of the organic semiconductor 2,7-dioctyl[1]benzothieno[3,2-b]benzothiophene (C8 -BTBT) into the perovskite formulation, where it facilitates the formation of large, near-single-crystalline-quality platelet-like (PEA)2 PbBr4 domains overlaid by a ≈5-nm-thin C8 -BTBT layer. Transistors with (PEA)2 PbBr4 /C8 -BTBT channels exhibit an unexpectedly large hysteresis window between forward and return bias sweeps. Material and device analysis combined with theoretical calculations suggest that the C8 -BTBT-rich phase acts as the hole-transporting channel, while the quantum wells in (PEA)2 PbBr4 act as the charge storage element where carriers from the channel are injected, stored, or extracted via tunneling. When tested as a non-volatile memory, the devices exhibit a record memory window (>180 V), a high erase/write channel current ratio (104 ), good data retention, and high endurance (>104 cycles). The results here highlight a new memory device concept for application in large-area electronics, while the growth technique can potentially be exploited for the development of other optoelectronic devices including solar cells, photodetectors, and light-emitting diodes.
RESUMO
Two-dimensional transition metal dichalcogenide nanoribbons are touted as the future extreme device downscaling for advanced logic and memory devices but remain a formidable synthetic challenge. Here, we demonstrate a ledge-directed epitaxy (LDE) of dense arrays of continuous, self-aligned, monolayer and single-crystalline MoS2 nanoribbons on ß-gallium (III) oxide (ß-Ga2O3) (100) substrates. LDE MoS2 nanoribbons have spatial uniformity over a long range and transport characteristics on par with those seen in exfoliated benchmarks. Prototype MoS2-nanoribbon-based field-effect transistors exhibit high on/off ratios of 108 and an averaged room temperature electron mobility of 65 cm2 V-1 s-1. The MoS2 nanoribbons can be readily transferred to arbitrary substrates while the underlying ß-Ga2O3 can be reused after mechanical exfoliation. We further demonstrate LDE as a versatile epitaxy platform for the growth of p-type WSe2 nanoribbons and lateral heterostructures made of p-WSe2 and n-MoS2 nanoribbons for futuristic electronics applications.