RESUMO
PURPOSE: We investigated the influence of passive arm-support exoskeleton (ASE) with different levels of torque (50, 75, and 100%) on upper arm osteokinematics. METHODS: Twenty participants completed a cyclic overhead drilling task with and without ASE. Task duration, joint angles, and angular acceleration peaks were analyzed during ascent and descent phases of the dominant upper arm. RESULTS: Maximum ASE torque was associated with decreased peak acceleration during ascent (32.2%; SD 17.8; p < 0.001) and descent phases (38.8%; SD 17.8; p < 0.001). Task duration remained consistent. Increased torque led to a more flexed (7.2°; SD 5.5; p > 0.001) and internally rotated arm posture (17.6°; SD 12.1; p < 0.001), with minimal changes in arm abduction. CONCLUSION: The small arm accelerations and changes in osteokinematics we observed, support the use of this ASE, even while performing overhead cyclic tasks with the highest level of support.
RESUMO
BACKGROUND: Musculoskeletal symptoms and injuries adversely impact the health of surgical team members and their performance in the operating room (OR). Though ergonomic risks in surgery are well-recognized, mitigating these risks is especially difficult. In this study, we aimed to assess the impacts of an exoskeleton when used by OR team members during live surgeries. METHODS: A commercial passive arm-support exoskeleton was used. One surgical nurse, one attending surgeon, and five surgical trainees participated. Twenty-seven surgeries were completed, 12 with and 15 without the exoskeleton. Upper-body postures and muscle activation levels were measured during the surgeries using inertial measurement units and electromyography sensors, respectively. Postures, muscle activation levels, and self-report metrics were compared between the baseline and exoskeleton conditions using non-parametric tests. RESULTS: Using the exoskeleton significantly decreased the percentage of time in demanding postures (>45° shoulder elevation) for the right shoulder by 7% and decreased peak muscle activation of the left trapezius, right deltoid, and right lumbar erector spinae muscles, by 7%, 8%, and 12%, respectively. No differences were found in perceived effort, and overall scores on usability ranged from "OK" to "excellent." CONCLUSIONS: Arm-support exoskeletons have the potential to assist OR team members in reducing musculoskeletal pain and fatigue indicators. To further increase usability in the OR, however, better methods are needed to identify the surgical tasks for which an exoskeleton is effective.
Assuntos
Eletromiografia , Exoesqueleto Energizado , Postura , Humanos , Masculino , Feminino , Adulto , Postura/fisiologia , Ergonomia , Equipe de Assistência ao Paciente , Salas Cirúrgicas , Braço/fisiologiaRESUMO
We assessed the effects of a passive, back-support exoskeleton (BSE) on lower-limb joint kinetics during the initiation and swing phases of recovery from a forward loss of balance. Sixteen (8M, 8F) young, healthy participants were released from static forward-leaning postures and attempted to recover their balance with a single-step while wearing a BSE (backXTM) with different levels of support torque and in a control condition. The BSE provided â¼ 15-20 Nm of external hip extension torque on the stepping leg at the end of initiation and beginning of swing phases. Participants were unable to generate sufficient hip flexion torque, power, and work to counteract this external torque, although they sustained hip flexion torque for a more prolonged period, resulting in slightly increased hip contribution to positive leg work (compared to control). However, net positive leg work, and the net contribution of hip joint (human + BSE) to total leg work decreased with BSE use. While all participants had changes in hip joint kinetics, a significant compensatory increase in ankle contribution to positive leg work was observed only among females. Our results suggest that BSE use adversely affects reactive stepping by decreasing the stepping leg kinetic energy for forward propulsion, and that the relative contributions of lower-limb joints to total mechanical work done during balance recovery are altered by BSE use. BSEs may thus need to be implemented with caution for dynamic tasks in occupational settings, as they may impair balance recovery following a forward loss of balance.
Assuntos
Exoesqueleto Energizado , Feminino , Humanos , Articulação do Joelho , Extremidade Inferior , Articulação do Quadril , Tornozelo , Fenômenos BiomecânicosRESUMO
OCCUPATIONAL APPLICATIONSIndustrial robots have become an important aspect in modern industry. In the context of human-robot collaboration, enabling teleoperated robots to work in close proximity to local/onsite humans can provide new opportunities to improve human engagement in a distributed workplace. Interviews with industry stakeholders highlighted several potential benefits of such teleoperator-robot-human collaboration (tRHC), including the application of tRHC to tasks requiring both expertise and manual dexterity (e.g., maintenance and highly skilled tasks in sectors including construction, manufacturing, and healthcare), as well as opportunities to expand job accessibility for individuals with disabilities and older individuals. However, interviewees also indicated potential challenges of tRHC, particularly related to human perception (e.g., perceiving remote environments), safety, and trust. Given these challenges, and the current limited information on the practical value and implementation of tRHC, we propose several future research directions, with a focus on human factors and ergonomics, to help realize the potential benefits of tRHC.
Background The increasing prevalence of robots in industrial environments is attributed in part to advancements in collaborative robot technologies, enabling robots to work in close proximity to humans. Simultaneously, the rise of teleoperation, involving remote robot control, poses unique opportunities and challenges for human-robot collaboration (HRC) in diverse and distributed workspaces.Purpose There is not yet a comprehensive understanding of HRC in teleoperation, specifically focusing on collaborations involving the teleoperator, the robot, and the local or onsite workers in industrial settings, here referred to as teleoperator-robot-human collaboration (tRHC). We aimed to identify opportunities, challenges, and potential applications of tRHC through insights provided from industry stakeholders, thereby supporting effective future industrial implementations.Methods Thirteen stakeholders in robotics, specializing in different domains (i.e., safety, robot manufacturing, aerospace/automotive manufacturing, and supply chains), completed semi-structured interviews that focused on exploring diverse aspects relevant to tRHC. The interviews were then transcribed and thematic analysis was applied to group responses into broader categories, which were further compared across stakeholder industries.Results We identified three main categories and 13 themes from the interviews. These categories include Benefits, Concerns, and Technical Challenges. Interviewees highlighted accessibility, ergonomics, flexibility, safety, time & cost saving, and trust as benefits of tRHC. Concerns raised encompassed safety, standards, trust, and workplace optimization. Technical challenges consisted of critical issues such as communication time delays, the need for high dexterity in robot manipulators, the importance of establishing shared situational awareness among all agents, and the potential of augmented and virtual reality in providing immersive control interfaces.Conclusions Despite important challenges, tRHC could offer unique benefits, facilitating seamless collaboration among the teleoperator, teleoperated robot(s), and onsite workers across physical and geographic boundaries. To realize such benefits and address the challenges, we propose several research directions to further explore and develop tRHC capabilities.
Assuntos
Ergonomia , Robótica , Robótica/métodos , Humanos , Ergonomia/métodos , Indústria Manufatureira/métodos , Sistemas Homem-Máquina , PesquisadoresRESUMO
Backpacks are common devices for carrying external posterior loads. However, relatively little is known about how these external loads affect the ability to recover from balance loss. In this exploratory investigation, 16 young adults (8 female, 8 male) performed forward and backward lean-and-release balance recovery trials, while wearing a backpack that was unloaded or loaded (at 15% of individual body weight). We quantified the effects of backpack loading on balance recovery in terms of maximum recoverable lean angles, center-of-mass kinematics, and temporal-spatial stepping characteristics. Mean values of maximum lean angles were 20° and 9° in response to forward and backward perturbations, respectively. These angles significantly decreased when wearing the additional load for only backward losses of balance. During backward losses of balance, the additional load decreased peak center-of-mass velocity and increased acceleration by â¼10 and 18% respectively, which was accompanied by â¼5% faster stepping responses and steps that were â¼9% longer, 11% higher, and had an â¼10% earlier onset. Thus, wearing a backpack decreases backward balance recovery ability and changes backward recovery stepping characteristics.
Assuntos
Aceleração , Equilíbrio Postural , Adulto Jovem , Humanos , Masculino , Feminino , Equilíbrio Postural/fisiologia , Fenômenos Biomecânicos , Suporte de Carga/fisiologiaRESUMO
INTRODUCTION: Sitting on an unstable surface is a common paradigm to investigate trunk postural control among individuals with low back pain (LBP), by minimizing the influence lower extremities on balance control. Outcomes of many small studies are inconsistent (e.g., some find differences between groups while others do not), potentially due to confounding factors such as age, sex, body mass index [BMI], or clinical presentations. We conducted a systematic review with an individual participant data (IPD) meta-analysis to investigate whether trunk postural control differs between those with and without LBP, and whether the difference between groups is impacted by vision and potential confounding factors. METHODS: We completed this review according to PRISMA-IPD guidelines. The literature was screened (up to 7th September 2023) from five electronic databases: MEDLINE, CINAHL, Embase, Scopus, and Web of Science Core Collection. Outcome measures were extracted that describe unstable seat movements, specifically centre of pressure or seat angle. Our main analyses included: 1) a two-stage IPD meta-analysis to assess the difference between groups and their interaction with age, sex, BMI, and vision on trunk postural control; 2) and a two-stage IPD meta-regression to determine the effects of LBP clinical features (pain intensity, disability, pain catastrophizing, and fear-avoidance beliefs) on trunk postural control. RESULTS: Forty studies (1,821 participants) were included for the descriptive analysis and 24 studies (1,050 participants) were included for the IPD analysis. IPD meta-analyses revealed three main findings: (a) trunk postural control was worse (higher root mean square displacement [RMSdispl], range, and long-term diffusion; lower mean power frequency) among individuals with than without LBP; (b) trunk postural control deteriorated more (higher RMSdispl, short- and long-term diffusion) among individuals with than without LBP when vision was removed; and (c) older age and higher BMI had greater adverse impacts on trunk postural control (higher short-term diffusion; longer time and distance coordinates of the critical point) among individuals with than without LBP. IPD meta-regressions indicated no associations between the limited LBP clinical features that could be considered and trunk postural control. CONCLUSION: Trunk postural control appears to be inferior among individuals with LBP, which was indicated by increased seat movements and some evidence of trunk stiffening. These findings are likely explained by delayed or less accurate corrective responses. SYSTEMATIC REVIEW REGISTRATION: This review has been registered in PROSPERO (registration number: CRD42021124658).
Assuntos
Dor Lombar , Humanos , Postura Sentada , Índice de Massa Corporal , Catastrofização , Análise de DadosRESUMO
Exoskeletons (EXOs) are a promising wearable intervention to reduce work-related musculoskeletal disorder risks among construction workers. However, the adoption of EXOs may differ with demographic characteristics. Survey data (n = 361) were collected from construction industry stakeholders and a summation score method was used to summarize respondent's benefits and barriers to EXO use, along with perceptions and readiness to use. Responses were stratified by race (White vs. non-White), sex (male vs. female), and age (<47 years vs. ≥47 years). Both a higher Benefits score and a higher Perceptions score were significantly and positively associated with a higher Readiness to Use score. There were also significant differences in perceived barriers to EXO use by race and sex. These results demonstrate substantial interest in EXO use but also emphasize the need to ensure proportionate access to the potential benefits of EXO technology.
Assuntos
Indústria da Construção , Exoesqueleto Energizado , Doenças Musculoesqueléticas , Humanos , Masculino , Feminino , Pessoa de Meia-Idade , Inquéritos e Questionários , Doenças Musculoesqueléticas/prevenção & controle , DemografiaRESUMO
Work-related musculoskeletal disorders (WMSDs) are a major health concern in the construction industry. Occupational exoskeletons (EXOs) are a promising ergonomic intervention to help reduce WMSD risk. Their adoption, however, has been low in construction. To understand the contributing factors to EXO use-intention and assist in future decision-making, we built decision trees to predict responses to each of three EXO use-intention questions (Try, Voluntary Use, and Behavioural Intention), using online survey responses. Variable selection and hyperparameter tuning were used respectively to reduce the number of potential predictors and improve prediction performance. The importance of variables in each final tree was calculated to understand which variables had a greater influence. The final trees had moderate prediction performance. The root node of each tree included EXOs becoming standard equipment, fatigue reduction, or performance increase. Important variables were found to be quite specific to different decision trees. Practical implications of the findings are discussed.Practitioner summary: This study used decision trees to identify key factors influencing the use-intention of occupational exoskeletons (EXOs) in construction, using online survey data. Key factors identified included EXOs becoming standard equipment, fatigue reduction, and performance improvement. Final trees provide intuitive visual representations of the decision-making process for workers to use EXOs.
RESUMO
Indoor fall monitoring is challenging for community-dwelling older adults due to the need for high accuracy and privacy concerns. Doppler radar is promising, given its low cost and contactless sensing mechanism. However, the line-of-sight restriction limits the application of radar sensing in practice, as the Doppler signature will vary when the sensing angle changes, and signal strength will be substantially degraded with large aspect angles. Additionally, the similarity of the Doppler signatures among different fall types makes it extremely challenging for classification. To address these problems, in this paper we first present a comprehensive experimental study to obtain Doppler radar signals under large and arbitrary aspect angles for diverse types of simulated falls and daily living activities. We then develop a novel, explainable, multi-stream, feature-resonated neural network (eMSFRNet) that achieves fall detection and a pioneering study of classifying seven fall types. eMSFRNet is robust to both radar sensing angles and subjects. It is also the first method that can resonate and enhance feature information from noisy/weak Doppler signatures. The multiple feature extractors - including partial pre-trained layers from ResNet, DenseNet, and VGGNet - extracts diverse feature information with various spatial abstractions from a pair of Doppler signals. The feature-resonated-fusion design translates the multi-stream features to a single salient feature that is critical to fall detection and classification. eMSFRNet achieved 99.3% accuracy detecting falls and 76.8% accuracy for classifying seven fall types. Our work is the first effective multistatic robust sensing system that overcomes the challenges associated with Doppler signatures under large and arbitrary aspect angles, via our comprehensible feature-resonated deep neural network. Our work also demonstrates the potential to accommodate different radar monitoring tasks that demand precise and robust sensing.
RESUMO
Occupational exoskeletons have become more prevalent as an ergonomic control to reduce the physical demands of workers. While beneficial effects have been reported, there is relatively little evidence regarding potential adverse effects of exoskeletons on fall risk. The purpose of this study was to investigate the effects of a leg-support exoskeleton on reactive balance after simulated slips and trips. Six participants (three females) used a passive, leg-support exoskeleton that provided chair-like support in three experimental conditions (no exoskeleton, low-seat setting, high-seat setting). In each of these conditions, participants were exposed to 28 treadmill perturbations from an upright standing posture simulating a backward slip (0.4-1.6 m/s) or a forward trip (0.75-2.25 m/s). The exoskeleton increased the probability of a failed recovery, and adversely affected reactive balance kinematics, after simulated slips and trips. After simulated slips, the exoskeleton decreased initial step length 0.039 m, decreased mean step speed 0.12 m/s, anteriorly displaced touchdown position of the initial recovery step by 0.045 m, and decreased PSIS height at initial step touchdown by 1.7 % sof its standing height. After simulated trips, the exoskeleton increased trunk angle at step 2.4 degrees, and decreased initial step length 0.033 m. These effects appeared to result from the exoskeleton inhibiting regular stepping motion due to its posterior placement on the lower limbs, added mass, and mechanical constraints on participant movement. Our results suggest care may be needed among leg-support exoskeleton users when at risk of slips or trips and motivate potential exoskeleton design modifications to reduce fall risk.
Assuntos
Perna (Membro) , Equilíbrio Postural , Feminino , Humanos , Marcha , Caminhada , Fenômenos BiomecânicosRESUMO
Evidence is emerging on how whole-body powered exoskeleton (EXO) use impacts users in basic occupational work scenarios, yet our understanding of how users learn to use this complex technology is limited. We explored how novice users adapted to using an EXO during gait. Six novices and five experienced users completed the study. Novices completed an initial training/familiarization gait session, followed by three subsequent gait sessions using the EXO, while experienced users completed one gait session with the EXO. Spatiotemporal gait measures, pelvis and lower limb joint kinematics, muscle activities, EXO torques, and human-EXO interaction forces were measured. Adaptations among novices were most pronounced in spatiotemporal gait measures, followed by joint kinematics, with smaller changes evident in muscle activity and EXO joint torques. Compared to the experienced users, novices exhibited a shorter step length and walked with significantly greater anterior pelvic tilt and less hip extension. Novices also used lower joint torques from the EXO at the hip and knee, and they had greater biceps femoris activity. Overall, our results may suggest that novices exhibited clear progress in learning, but they had not yet adopted motor strategies similar to those of experienced users after the three sessions. We suggest potential future directions to enhance motor adaptations to powered EXO in terms of both training protocols and human-EXO interfaces.
Assuntos
Exoesqueleto Energizado , Humanos , Projetos Piloto , Músculo Esquelético/fisiologia , Caminhada/fisiologia , Marcha/fisiologia , Fenômenos BiomecânicosRESUMO
Arm-support exoskeletons (ASEs) are an emerging technology with the potential to reduce physical demands during diverse tasks, especially overhead work. However, limited information is available about the effects of different ASE designs during overhead work with diverse task demands. Eighteen participants (gender-balanced) performed lab-based simulations of a pseudo-static overhead task. This task was performed in six different conditions (3 work heights × 2 hand force directions), with each of three ASEs and in a control condition (i.e., no ASE). Using ASEs generally reduced the median activity of several shoulder muscles (by â¼12-60%), changed working postures, and decreased perceived exertion in several body regions. Such effects, though, were often task-dependent and differed between the ASEs. Our results support earlier evidence of the beneficial effects of ASEs for overhead work but emphasize that: 1) these effects depend on the task demands and ASE design and 2) none of the ASE designs tested was clearly superior across the tasks simulated.
Assuntos
Exoesqueleto Energizado , Humanos , Eletromiografia , Esforço Físico , Braço , Análise e Desempenho de Tarefas , Postura/fisiologia , Músculo Esquelético/fisiologia , Ombro/fisiologia , Fenômenos BiomecânicosRESUMO
Low-back pain (LBP) continues as the leading cause of work-related musculoskeletal disorders, and the high LBP burden is attributed largely to physical risk factors prevalent in manual material handling tasks. Industrial back-support exoskeletons (BSEs) are a promising ergonomic intervention to help control/prevent exposures to such risk factors. While earlier research has demonstrated beneficial effects of BSEs in terms of reductions in superficial back muscle activity, limited evidence is available regarding the impacts of these devices on spine loads. We evaluated the effects of two passive BSEs (BackX™ AC and Laevo™ V2.5) on lumbosacral compression and shear forces during repetitive lifting using an optimization-based model. Eighteen participants (gender-balanced) completed four minutes of repetitive lifting in nine different conditions, involving symmetric and asymmetric postures when using the BSEs (along with no BSE as a control condition). Using both BSEs reduced estimated peak compression and anteroposterior shear forces (by â¼8-15%). Such reductions, however, were task-specific and depended on the BSE design. Laevo™ use reduced mediolateral shear forces during asymmetric lifting (by â¼35%). We also found that reductions in composite measures of trunk muscle activity may not correspond well with changes in spine forces when using a BSE. These results can help guide the proper selection and application of BSEs during repetitive lifting tasks. Future work is recommended to explore the viability of different biomechanical models to assess changes in spine mechanical loads when using BSEs and whether reasonable estimates would be obtained using such models.
Assuntos
Exoesqueleto Energizado , Dor Lombar , Humanos , Remoção , Coluna Vertebral/fisiologia , Vértebras Lombares/fisiologia , Região Lombossacral , Dor Lombar/prevenção & controle , Dor Lombar/etiologia , Fenômenos Biomecânicos/fisiologia , Eletromiografia , Suporte de Carga/fisiologiaRESUMO
Slips, trips, and falls are some of the most substantial and prevalent causes of occupational injuries and fatalities, and these events may contribute to low-back problems. We quantified lumbar kinematics (i.e., lumbar angles relative to pelvis) and kinetics during unexpected slip and trip perturbations, and during normal walking, among 12 participants (6F, 6 M). Individual anthropometry, lumbar muscle geometry, and lumbar angles, along with electromyography from 14 lumbar muscles were used as input to a 3D, dynamic, EMG-based model of the lumbar spine. Results indicated that, in comparison with values during normal walking, lumbar range of motion, lumbosacral (L5/S1) loads, and lumbar muscle activations were all significantly higher during the slip and trip events. Maximum L5/S1 compression forces exceeded 2700 N during slip and trip events, compared with â¼ 1100 N during normal walking. Mean values of L5/S1 anteroposterior (930 N), and lateral (800 N) shear forces were also substantially larger than the shear force during the normal walking (230 N). These observed levels of L5/S1 reaction forces, along with high levels of bilateral lumbar muscle activities, suggest the potential for overexertion injuries and tissue damage during unexpected slip and trip events, which could contribute to low back injuries. Outcomes of this study may facilitate the identification and control of specific mechanisms involved with low back disorders consequent to slips or trips.
Assuntos
Vértebras Lombares , Músculo Esquelético , Humanos , Músculo Esquelético/fisiologia , Suporte de Carga/fisiologia , Vértebras Lombares/fisiologia , Eletromiografia , Caminhada/fisiologia , Fenômenos Biomecânicos/fisiologiaRESUMO
Load carriage is an inevitable daily task for soldiers. The purposes of this study were to explore the extent to which gait variability (GV) is affected by load carriage and experience among military cadets, and whether experience-related differences in GV are dependent on task demand. Two groups of cadets (30 experienced, 30 less experienced) completed a load carriage task in each of three load conditions (no load, 16 kg, 32 kg). Three categories of GV measures were obtained: spatiotemporal variability, joint kinematic variability, and Lyapunov exponents. Compared to traditional mean gait measures, GV measures were more discriminative of experience: although both groups showed similar mean gait measures, the experienced participants had reduced variability in spatiotemporal measures (p ≤ 0.008) and joint kinematics (p ≤ 0.004), as well as lower levels of long-term local dynamic stability at the ankle (p = 0.040). In both groups, heavier loads were also caused increased GV (p ≤ 0.018) and enhanced short-term local dynamic stability at the knee (p = 0.014). These results emphasize the importance of GV measures, which may provide a more complete description of adaptability, stability, and control; highlight alternate movement strategies during more difficult load carriage; and capture experience-related differences in load carriage strategies.
Assuntos
Militares , Humanos , Suporte de Carga , Marcha , Fenômenos Biomecânicos , Articulação do Tornozelo , CaminhadaRESUMO
Industrial exoskeletons are a promising ergonomic intervention to reduce the risk of work-related musculoskeletal disorders by providing external physical support to workers. Passive exoskeletons, having no power supplies, are of particular interest given their predominance in the commercial market. Understanding the mechanical behavior of the torque generation mechanisms embedded in passive exoskeletons is, however, essential to determine the efficacy of these devices in reducing physical loads (e.g., in manual material handling tasks). We introduce a novel approach using a computerized dynamometer to quantify the assistive torque profiles of two passive back-support exoskeletons (BSEs) at different support settings and in both static and dynamic conditions. The feasibility of this approach was examined using both human subjects and a mannequin. Clear differences in assistive torque magnitudes were evident between the two BSEs, and both devices generated more assistive torques during trunk/hip flexion than extension. Assistive torques obtained from human subjects were often within similar ranges as those from the mannequin, though values were more comparable over a narrow range of flexion/extension angles due to practical limitations with the dynamometer and human subjects. Characterizing exoskeleton assistive torque profiles can help in better understanding how to select a torque profile for given task requirements and user anthropometry, and aid in predicting the potential impacts of exoskeleton use by incorporating measured torque profiles in a musculoskeletal modeling system. Future work is recommended to assess this approach for other occupational exoskeletons.
RESUMO
Back-support exoskeletons (BSEs) are a promising ergonomic intervention for reducing physical demands on the low-back, but little is known regarding whether BSE use alters balance recovery following external perturbations. Hence, we investigated the effects of wearing a BSE on single-step balance recovery following a forward loss of balance. Sixteen (8 M, 8F) young, healthy participants were released from static forward-leaning postures and attempted to recover their balance with a single step while wearing a BSE (backXTM) with three different levels of support torque (i.e., no torque, low, and high) and in a control condition (no exoskeleton). Lean angle was increased until they failed in two consecutive trials to recover their balance with a single step. The maximum lean angle from which individuals could successfully recover was not significantly altered when wearing the BSE. However, wearing the BSE under all torque conditions increased reaction times. The BSE also impeded hip flexion (i.e., decrease in both peak hip flexion angle and angular velocity), resulting in decreased peak knee flexion velocity, knee range of motion, and step length. Measures of the margin of stability decreased significantly in the high-torque BSE condition. Overall, our results suggest that use of a BSE that provides external hip extension torque impairs balance recovery responses. Future work extending kinetic analyses to recovery responses, as well as a study of recovery when responding to slips and trips while walking, would offer a more complete picture of how a BSE may impact balance recovery following a loss of balance.
Assuntos
Envelhecimento , Equilíbrio Postural , Humanos , Equilíbrio Postural/fisiologia , Fenômenos Biomecânicos , Envelhecimento/fisiologia , Caminhada/fisiologiaRESUMO
We assessed the effects of using a passive back-support exoskeleton (BSE) on lower limb joint kinematics and kinetics during level walking. Twenty young, healthy participants completed level walking trials while wearing a BSE (backXTM) with three different levels of hip-extension support torque (i.e., no torque, low, and high) and in a control condition (no-BSE). When hip extension torques were required for gait-initial 0-10% and final 75-100% of the gait cycle-the BSE with high supportive torque provided ~ 10 Nm of external hip extension torque at each hip, resulting in beneficial changes in participants' gait patterns. Specifically, there was a ~ 10% reduction in muscle-generated hip extension torque and ~ 15-20% reduction in extensor power. During the stance-swing transition, however, BSE use produced undesirable changes in lower limb kinematics (e.g., 5-20% increase in ankle joint velocity) and kinetics (e.g., ~ 10% increase in hip flexor, knee extensor, and ankle plantarflexor powers). These latter changes likely stemmed from the need to increase mechanical energy for propelling the leg into the swing phase. BSE use may thus increase the metabolic cost of walking. Whether such use also leads to muscle fatigue and/or postural instability in long-distance walking needs to be confirmed in future work.
Assuntos
Exoesqueleto Energizado , Fenômenos Biomecânicos , Marcha/fisiologia , Articulação do Quadril , Humanos , Articulação do Joelho/fisiologia , Extremidade Inferior , Caminhada/fisiologiaRESUMO
OCCUPATIONAL APPLICATIONSResults of the current exploratory study suggest that use of an exoskeleton (EXO) has the potential to be accepted by workers as an intervention in diverse manufacturing environments. Also evident were that the major factors contributing to EXO-use-intention are perceived comfort, task-technology fit, perceived safety, and perceived usefulness. A user's perception of perceived usability may be established by using an exoskeleton during actual job tasks, yet some aspects of perceived usability likely require multiple exposures to an EXO for an accurate assessment. Many negative comments regarding EXO use were related to physical constraints (e.g., restricted movements, bulkiness), and to the EXO interface (e.g., straps, cuff designs), suggesting a need for further research on EXO design to minimize discomfort. In practice, there is likely value in having workers use and explore candidate EXOs during their actual job, both to accurately assess the usefulness of an EXO and to find the most effective EXO.
Background There lacks an understanding of using an exoskeleton (EXO) in diverse manufacturing environments.Purpose Goals of this study were to: (1) gather worker feedback on different EXOs after using them during their actual jobs; (2) understand what contributes to EXO-use-intention in manufacturing companies; and (3) develop a decision tree model to explore which task characteristics and user perceptions might aid in determining how to implement an EXO effectively.Methods A field study was completed in five manufacturing companies in the state of Ohio. Fifteen participants used preferred EXOs selected from among two arm-support and two back-support devices during their regular jobs for ≤30 minutes in each of two separate sessions. After using an EXO, participants completed a questionnaire addressing several aspects of usability, comfort, safety, and EXO-use-intention. Open-ended comments on these aspects were coded into emerging themes. A decision tree analysis was performed on participants' responses to the EXO-use-intention question to explore the predictive value of task characteristics, user characteristics, and questionnaire responses.Results Responses to usability-related questions were rather consistent between the two sessions, yet some responses were more positive in the 2nd session (perceived balance, overall comfort and fit, and range-of-motion). We identified four themes regarding EXO useutility for work, wearability, working metrics, and ease of using; and negative comments on these themes were largely related to physical constraints from wearing an EXO, and EXO interface. The decision tree analysis suggested that perceived comfort, task-technology fit, perceived safety, and perceived usefulness are each associated with EXO-use-intention.Conclusions EXO use has the potential to be accepted by workers as an intervention in manufacturing environments. However, further work is needed for enhanced comfort, EXO-task fit, user acceptance, and to develop EXO introduction processes to create best practices for effective implementation and sustainable use of EXOs in practice.
Assuntos
Exoesqueleto Energizado , Humanos , MovimentoRESUMO
BACKGROUND: Back-support exoskeletons (BSEs) are a promising intervention to mitigate physical demands at work. Although growing evidence indicates that BSEs can reduce low-back physical demands, there is limited understanding of potential unintended consequences of BSE use, including the risk of falls. RESEARCH QUESTION: Does using a BSE adversely affect gait performance and stability, and are such effects dependent on specific BSE external torque characteristics? METHODS: Twenty participants (10 M, 10 F) completed five level over-ground walking trials and a five-minute treadmill walking trial while wearing a BSE (backX™) with three different levels of external torque (i.e., no torque, low torque, and high torque) and in a control (no-exoskeleton) condition. Spatiotemporal gait patterns, stride-to-stride gait variability measures, required coefficient-of-friction (RCoF), and minimum foot clearance (MFC) were determined, to assess gait performance. Gait stability was quantified using the maximum Lyapunov exponent (MLE) of trunk kinematics and the margin-of-stability (MoS). RESULTS: Using the backX™ with high supportive torque decreased slip risk (7% decrease in RCoF) and slightly improved trunk stability (3% decrease in MLE). However, it also decreased step length (1%), increased step width (10%) and increased gait variability (8-19%). Changes in MoS were complex: while MoS at heel strike decreased in the AP direction, it increased in the ML direction. There was a rather large decrease in MoS (26%) in the ML direction during the swing phase. SIGNIFICANCE: This is the first study to quantify the effects of wearing a passive BSE with multiple supportive torque levels on gait performance and stability during level walking. Our results, showing that the external torque of the BSE may adversely affect gait step width, variability, and dynamic stability, can contribute to better design and practice guidelines to facilitate the safe adoption of BSEs in the workplace.