Mercury adsorption on activated carbon in Waste-to-Energy: Model development and validation on real plant data.

A model capable to estimate the mercury (Hg) removal efficiency in the fabric filter of a real Waste-to-Energy plant with dynamic operating conditions has been developed. The mathematical model is based on Langmuir equation and Hg mass balance on mercury, in both gaseous and adsorbed phases, along the growing filter cake and inside the activated carbon particles. The activated carbon properties and the Langmuir isotherm parameters have been obtained by fitting the model to real plant data, characterized by variable mercury inlet concentrations. The model is then validated on another dataset coming from the same plant. The obtained Hg removal efficiency falls within ± 3 % error band and with a mean absolute percentage error equal to 0.87 %. The model is suitable for the development of a data-driven activated carbon feed control strategy to increase the economic and environmental sustainability of the WtE plants as well as in the development of virtual sensors to use as a replacement when the continuous stack mercury monitors fail.

A climate mitigation action index at the local scale: Methodology and case study.

This paper presents a novel climate mitigation action index to evaluate various aspects linked to the implementation of Sustainable Energy Action Plans (SEAP), which define the carbon dioxide emission reduction targets and outline the key actions to achieve these at the municipal level. A SEAP Implementation Index (SII) is developed and applied to study climate change mitigation actions implemented by 102 Municipalities belonging to the Metropolitan City of Milan (Italy) in the framework of the Covenant of Mayors (CoM). The SII is composed of six categories and 16 sub-indicators and results in a final score ranging from 1 to 10. The average rating obtained in the case study area is 4.2, and only eleven Municipalities achieved an evaluation higher than 6. The sensitivity analysis shows the index robustness against variations in the applied weight factors. The population engagement and the management of the initiative, neglected by many Municipalities mostly because of a lack of funding and personnel, are identified as the most critical aspects. Despite the massive participation in the CoM, no quantitative analysis of the SEAPs implementation has been proposed until now and this study shows some severe shortcomings in their application.

Ultrafine particles (UFPs) from domestic wood stoves: genotoxicity in human lung carcinoma A549 cells.

In this paper, results on the potential toxicity of ultrafine particles (UFPs d<100nm) emitted by the combustion of logwood and pellet (hardwood and softwood) are reported. The data were collected during the TOBICUP (TOxicity of BIomass COmbustion generated Ultrafine Particles) project, carried out by a team composed of interdisciplinary research groups. The genotoxic evaluation was performed on A549 cells (human lung carcinomacells) using UFPs whose chemical composition was assessed by a suite of analytical techniques. Comet assay and γ-H2AX evaluation show a significant DNA damage after 24h treatment. The interpretation of the results is based on the correlation among toxicological results, chemical-physical properties of UFPs, and the type and efficiency conditions in residential pellet or logwood stoves.

The chemical composition of ultrafine particles and associated biological effects at an alpine town impacted by wood burning.

This work is part of the TOBICUP (TOxicity of BIomass Combustion generated Ultrafine Particles) project which aimed at providing the composition of ultrafine particles (UFPs, i.e. particles with aerodynamic diameter, dae, lower than 100nm) emitted by wood combustion and elucidating the related toxicity. Results here reported are from two ambient monitoring campaigns carried out at an alpine town in Northern Italy, where wood burning is largely diffused for domestic heating in winter. Wintertime and summertime UFP samples were analyzed to assess their chemical composition (i.e. elements, ions, total carbon, anhydrosugars, and polycyclic aromatic hydrocarbons) and biological activity. The induction of the pro-inflammatory cytokine interleukin-8 (IL-8) by UFPs was investigated in two human cells lines (A549 and THP-1) and in human peripheral blood leukocytes. In addition, UFP-induced oxidative stress and genotoxicity were investigated in A549 cells. Ambient UFP-related effects were compared to those induced by traffic-emitted particles (DEP) taken from the NIES reference material "vehicle exhaust particulates". Ambient air UFPs induced a dose-related IL-8 release in both A549 and THP-1 cells; the effect was more relevant on summer samples and in general THP-1 cells were more sensitive than A549 cells. On a weight basis our data did not support a higher biological activity of ambient UFPs compared to DEP. The production of IL-8 in the whole blood assay indicated that UFPs reached systemic circulation and activated blood leukocytes. Comet assay and γ-H2AX evaluation showed a significant DNA damage especially in winter UFPs samples compared to control samples. Our study showed that ambient UFPs can evoke a pulmonary inflammatory response by inducing a dose-related IL-8 production and DNA damage, with different responses to UFP samples collected in the summer and winter periods.

Insights on wood combustion generated proinflammatory ultrafine particles (UFP).

This study aimed to collect, characterize ultrafine particles (UFP) generated from the combustion of wood pellets and logs (softwood and hardwood) and to evaluate their pro-inflammatory effects in THP-1 and A549 cells. Both cell lines responded to UFP producing interleukin-8 (IL-8), with wood log UFP being more active compared to pellet UFP. With the exception of higher effect observed with beech wood log UFP in THP-1, the ability of soft or hard woods to induce IL-8 release was similar. In addition, on weight mass, IL-8 release was similar or lower compared to diesel exhaust particles (DEP), arguing against higher biological activity of smaller size particles. UFP-induced IL-8 could be reduced by SB203580, indicating a role of p38MAPK activation in IL-8 production. The higher activity of beech wood log UFP in THP-1 was not due to higher uptake or endotoxin contamination. Qualitatively different protein adsorption profiles were observed, with less proteins bound to beech UFP compared to conifer UFP or DEP, which may provide higher intracellular availability of bioactive components, i.e. levoglucosan and galactosan, toward which THP-1 were more responsive compared to A549 cells. These results contribute to our understanding of particles emitted by domestic appliances and their biological effects.

Factors governing particle number emissions in a waste-to-energy plant.

Particle number concentration and size distribution measurements were performed on the stack gas of a waste-to-energy plant which co-incinerates municipal solid waste, sewage sludge and clinical waste in two lines. Average total number of particles was found to be 4.0·10(5)cm(-3) and 1.9·10(5)cm(-3) for the line equipped with a wet flue gas cleaning process and a dry cleaning system, respectively. Ultrafine particles (dp<100nm) accounted for about 97% of total number concentration for both lines, whereas the nanoparticle (dp<50nm) contribution differed slightly between the lines (87% and 84%). The experimental data is explored statistically through some multivariate pattern identifying methods such as factor analysis and cluster analysis to help the interpretation of the results regarding the origin of the particles in the flue gas with the objective of determining the factors governing the particle number emissions. The higher moisture of the flue gas in the wet cleaning process was found to increase the particle number emissions on average by a factor of about 2 due to increased secondary formation of nanoparticles through nucleation of gaseous precursors such as sulfuric acid, ammonia and water. The influence of flue gas dilution and cooling monitored through the variation of the sampling conditions also confirms the potential effect of the secondary new particle formation in increasing the particle number emissions. This finding shows the importance of reporting the experimental conditions in detail to enable the comparison and interpretation of particle number emissions. Regarding the fuel characteristics no difference was observed in terms of particle number concentration and size distributions between the clinical waste feed and the municipal solid waste co-incineration with sludge.

A methodology for elemental and organic carbon emission inventory and results for Lombardy region, Italy.

This paper presents a methodology and its application for the compilation of elemental carbon (EC) and organic carbon (OC) emission inventories. The methodology consists of the estimation of EC and OC emissions from available total suspended particulate matter (TSP) emission inventory data using EC and OC abundances in TSP derived from an extensive literature review, by taking into account the local technological context. In particular, the method is applied to the 2008 emissions of Lombardy region, Italy, considering 148 different activities and 30 types of fuels, typical of Western Europe. The abundances estimated in this study may provide a useful basis to assess the emissions also in other emission contexts with similar prevailing sources and technologies. The dominant sources of EC and OC in Lombardy are diesel vehicles for EC and the residential wood combustion (RWC) for OC which together account for about 83% of the total emissions of both pollutants. The EC and OC emissions from industrial processes and other fuel (e.g., gasoline, kerosene and LPG) combustion are significantly lower, while non-combustion sources give an almost negligible contribution. Total EC+OC contribution to regional greenhouse gas emissions is positive for every sector assuming whichever GWP100 value within the range proposed in literature. An uncertainty assessment is performed through a Monte Carlo simulation for RWC, showing a large uncertainty range (280% of the mean value for EC and 70% for OC), whereas for road transport a qualitative analysis identified a narrower range of uncertainty.

Number concentration and chemical composition of ultrafine and nanoparticles from WTE (waste to energy) plants.

Stack field testing at four municipal waste-to-energy (WTE) plants was conducted to investigate total number concentrations and size distributions in a size range extended towards the evaluation of ultrafine (UFP) and nanoparticle (NP) fractions with diameters smaller than 100nm and 50nm, respectively. Measurements were performed with a specifically designed sampling line, equipped with a dilution system and a particle counting device for measuring both primary particles in raw flue gases at stack conditions and the contributions of condensable origin, arising from their cooling and dilution immediately following stack release into the atmosphere. Average concentration levels detected ranged between 5×10(3)-6×10(5)cm(-3): for all sampling conditions, ultrafine fractions largely prevailed in number size distributions, with average diameters constantly located in the nanoparticle size range. Stack concentrations appeared to be influenced by the design and process configuration of flue gas cleaning systems, with most significant effects related to the presence of wet scrubbing units and the baghouse operating temperature of dry removal processes. Chemical speciation (i.e., trace metals, anions and cations, carbonaceous compounds) of size-resolved particulate fractions was performed on one of the plants. NP and UFP composition was essentially in accordance with the most important fuel and combustion process characteristics: in particular, the presence of chlorides and metal species was consistent with the respective waste feed content and their expected behavior during combustion and flue gas cleaning processes.

Pedestrian exposure to size-resolved particles in Milan.

Measurement campaigns for airborne particles along a pedestrian route in the city center of Milan were performed by means of a portable instrument consisting of an optical particle counter and a global positioning system (GPS) signal receiver. Based on the size-resolved particle number concentration data and on proper density factors experimentally determined for Milan urban area, the mass concentrations were calculated in terms of particulate matter with aerodynamic diameters < or =10 microm (PM10), < or =2.5 pm (PM2.5), and < or =1 microm (PM1). Besides directly measuring the personal exposure to PM throughout the route, the measurement campaigns pointed out small spatial and temporal variations of the concentration ranges in the different urban microenvironments visited along the route as well as very peculiar features of the particles levels in the underground subway. These findings suggested that the personal exposure of pedestrians in the city center could be estimated by simply taking into account the exposure at the open air and in the subway. The comparison between measured and calculated exposures according to the microenvironment-based estimation results in reasonable accordance, even though the estimations tend to slightly underestimate (12%) the actual measured exposure.