Emission performance evaluation of urban passenger car fleet through field investigation data in a megacity.

Continued improvements in living standards and the economic well-being in the megacities have led to a huge surge in vehicular density. The worst environmental outcome of the same has been persistent unsafe urban air quality, thanks to vehicular emission. Further, the existing inspection and maintenance programs, conceived to check such emission remain largely ineffective, particularly in developing countries. This is due to the absence of a thorough assessment of the vehicle's compliance with the in-use emission norms generated through reliable field investigation data. To address this gap, the present comprehensive study collected real-time tailpipe emission data from 2040 cars in Delhi, India. Exhaust emission parameters, namely, CO (carbon monoxide), HC (hydrocarbon), and SE (smoke emission), were recorded from both petrol and diesel-driven cars of private ownership, in collaboration with the emission compliance test centers. The performance of cars was assessed in terms of their compliance with the in-use BS (Bharat Stage) emission norms. The one-of-its-kind study reported the petrol cars to be highly compliant toward the BS IV norm while faring even better toward BS II for both CO and HC emissions (80-90%). The conformance to the HC norm was found to be typically better than that for CO (85-90% versus 75-80%). For the diesel-driven cars, BS III compliance levels were reported relatively better compared to BS IV (90% in the case of the former against 80% in the latter's case). Further, the study puts forward a clear indication that the in-use emission norm and maintenance status of cars have a direct and negative relationship with tailpipe emission parameters. Cars of both overseas and domestic origin have almost equal degrees of compliance with the emission norms (over 80% in any case). The study recommends the incorporation of these two critical vehicular variables, i.e., maintenance status and in-use emission standard in the emission certification policy.

Biological approaches for E-waste management: A green-go to boost circular economy.

E-waste is a pressing situation on human due to its complex composition. Although E-waste on one hand has some toxic components but at the same time, it would be a promising business sector. Recycling of E-waste to mine-out valuable metals and other components has opened a chance of business and hence a way towards transformation of linear economy to circular one. Chemical, physical and traditional technologies are holding the position in E-waste recycling sector but sustainability with respect to cost and environmental issues is a major concern associated with these technologies. In order to overcome these gaps, lucrative, environment friendly and sustainable technologies need to be implied. Biological approaches could be a green and clean approach to handle E-waste through sustainable and cost-effective means by considering socio-economic and environmental aspects. This review elaborates biological approaches for E-waste management and advancements in expanse. The novelty covers the environmental and socio-economic impacts of E-waste, solution and further scope of biological approaches, further research and development need in this contour to come up with sustainable recycling process.

Size and Zeta Potential Clicked Germination Attenuation and Anti-Sporangiospores Activity of PEI-Functionalized Silver Nanoparticles against COVID-19 Associated Mucorales (Rhizopus arrhizus).

The SARS-CoV-2 infections in Indian people have been associated with a mucormycotic fungal infection caused by the filamentous fungi Rhizopus arrhizus. The sporangiospores of R. arrhizus are omnipresent in the environment and cause infection through inhalation or ingestion of contaminated air and foods. Therefore, the anti-sporangiospore activity of polyethyleneimine functionalized silver nanoparticles (PEI-f-Ag-NPs) with variable size and surface charge as a function of the molecular weight of PEI was explored. The results showed that both PEI-f-AgNP-1 and PEI-f-AgNP-2, potentially, attenuated the germination and reduced the viability of sporangiospores. Furthermore, the results showed that the minimum inhibitory concentration (MIC) values of both PEI-f-AgNP-1 and PEI-f-AgNP-2 (1.65 and 6.50 µg/mL, respectively) were dependent on the nanoparticle size and surface ζ potentials. Similarly, the sporangiospore germination inhibition at MIC values was recorded, showing 97.33% and 94% germination inhibition, respectively, by PEI-f-AgNP-1 and 2 within 24 h, respectively. The confocal laser scanning microscopy, SEM-EDS, and confocal Raman spectroscopy investigation of PEI-f-Ag-NPs treated sporangiospores confirmed size and surface charge-dependent killing dynamics in sporangiospores. To the best of our knowledge, this is the first investigation of the polyethyleneimine functionalized silver nanoparticle-mediated size and surface charge-dependent anti-sporangiospore activity against R. arrhizus, along with a possible antifungal mechanism.

An in situ exploratory analysis of diesel cars' emission: way forward on policy evaluation.

Keeping in view the significant number of diesel-driven passenger cars in the existing light motor vehicle fleet in Delhi, India, a case study on smoke emission measurement from 460 number of such cars was conducted. Smoke exhaust data was collected from the diesel cars while the vehicles presented themselves for periodic renewal of pollution under control (PUC) certification at authorized emission testing centers across Delhi, India. Along with the smoke emission, various vehicle- and engine-related aspects, supposed to affect tailpipe smoke emission, were also recorded aiming at data analysis for two datasets, namely whole and top 5 makes. The smoke density under no-loading condition in the free acceleration test mode was measured. The study reported a strong correlation between vehicle parameters, such as age, mileage, maintenance category, emission norm, and engine aspiration; and the smoke emission (R2 values for vehicle age and mileage vs. smoke emission for whole dataset = 0.872 and 0.873, respectively). Top 5 make-wise correlations fared even better (R2 for age and mileage vs. emission in the range of 0.85-0.92 and 0.86-0.93, respectively). Further, the predictive emission equations using best-fit trendlines were also developed for both datasets. Such equations may be used by the car manufacturers to adopt a suitable strategy for tuning of engine or vehicle as such, to retain their cars in the longer state of compliance to the extant emission norms. Further, the study recommends to include vehicle mileage as an important factor in upgrading the existing inspection and maintenance programs, especially in the developing countries.

Nanotechnology: A Potential Weapon to Fight against COVID-19.

The COVID-19 infections have posed an unprecedented global health emergency, with nearly three million deaths to date, and have caused substantial economic loss globally. Hence, an urgent exploration of effective and safe diagnostic/therapeutic approaches for minimizing the threat of this highly pathogenic coronavirus infection is needed. As an alternative to conventional diagnosis and antiviral agents, nanomaterials have a great potential to cope with the current or even future health emergency situation with a wide range of applications. Fundamentally, nanomaterials are physically and chemically tunable and can be employed for the next generation nanomaterial-based detection of viral antigens and host antibodies in body fluids as antiviral agents, nanovaccine, suppressant of cytokine storm, nanocarrier for efficient delivery of antiviral drugs at infection site or inside the host cells, and can also be a significant tool for better understanding of the gut microbiome and SARS-CoV-2 interaction. The applicability of nanomaterial-based therapeutic options to cope with the current and possible future pandemic is discussed here.

Amine-Functionalized Silver Nanoparticles: A Potential Antiviral-Coating Material with Trap and Kill Efficiency to Combat Viral Dissemination (COVID-19).

The outbreak of COVID-19 has drastically affected the daily lifestyles of people globally where specific Coronavirus-2 transmits primarily by respiratory droplets. Structurally, the SARS-CoV-2 virus is made up of four types of proteins in which S-protein is indispensable among them, as it causes rapid replication in the host body. Therefore, the glycine and alanine composed of HR1 of S-protein is the ideal target for antiviral action. Different forms of surface-active PPEs can efficiently prevent this transmission in this circumstance. However, the virus can survive on the conventional PPEs for a long time. Hence, the nanotechnological approaches based on engineered nanomaterials coating on medical equipments can potentially prevent the dissemination of infections in public. Silver nanoparticles with tuneable physicochemical properties and versatile chemical functionalization provide an excellent platform to combat the disease. The coating of amine-functionalized silver nanoparticle (especially amine linked to aliphatic chain and trialkoxysilane) in its nanostructured form enables cloths trap and kill efficient. PPEs are a primary and reliable preventive measure, although they are not 100% effective against viral infections. So, developing and commercializing surface-active PPEs with trap and kill efficacy is highly needed to cope with current and future viral infections. This review article discusses the COVID-19 morphology, antiviral mechanism of Ag-NPs against SARS-CoV-2 virus, surface factors that influence viral persistence on fomites, the necessity of antiviral PPEs, and the potential application of amine-functionalized silver nanoparticles as a coating material for the development of trap and kill-efficient face masks and PPE kits.

Polyethylenimine-mediated controlled synthesis of Prussian blue-gold nanohybrids for biomedical applications.

We report on polyethylenimine (PEI)-mediated synthesis of Prussian blue nanoparticles (PBNPs) and gold nanoparticles (AuNPs); the formation of PBNP-AuNP nanohybrids with a remarkable change in Prussian blue character as a function of gold cation concentration was also considered. It was shown that PEI-protected polycrystalline PBNPs can be synthesized in an acidic medium from the precursor potassium ferricyanide [K3Fe(CN)6] at 60 °C. Since PEI also enables the controlled formation of gold nanoparticles (AuNPs) in the presence of formaldehyde under ambient conditions, nanohybrids of PBNPs and AuNPs were prepared. The formation of AuNPs was recorded over a wide range of PEI concentrations, which allowed control over polymeric cation capping of the AuNPs. PEI concentration-dependent enhancement/quenching of fluorescence/resonance Rayleigh scattering was useful for non-enzymatic detection of serum glucose levels. The resonance Rayleigh scattering intensity of PBNPs was several-fold higher than that of AuNPs and acted as a potent quencher of fluorescence. At an optimal concentration of PEI, AuNPs allowed an increase in the fluorescence signal as function of glucose concentration; the quenching ability of PB was demonstrated to be a function of the glucose concentration. This method is efficient for fast glucose sensing and offers a wider linear dynamic range, 0-10 mM, which is useful for non-enzymatic detection of serum glucose levels.

Nanostructured diamond for biomedical applications.

Nanostructured forms of diamond have been recently considered for use in a variety of medical devices due to their unusual biocompatibility, corrosion resistance, hardness, wear resistance, and electrical properties. This review considers several routes for the synthesis of nanostructured diamond, including chemical vapor deposition, hot filament chemical vapor deposition, microwave plasma-enhanced chemical vapor deposition, radio frequency plasma-enhanced chemical vapor deposition, and detonation synthesis. The properties of nanostructured diamond relevant to medical applications are described, including biocompatibility, surface modification, and cell attachment properties. The use of nanostructured diamond for bone cell interactions, stem cell interactions, imaging applications, gene therapy applications, and drug delivery applications is described. The results from recent studies indicate that medical devices containing nanostructured diamond can provide improved functionality over existing materials for the diagnosis and treatment of various medical conditions.

Microneedle-based transdermal electrochemical biosensors based on Prussian blue-gold nanohybrid modified screen-printed electrodes.

We report on the fabrication of a microneedle-based electrochemical biosensor for use in transdermal biosensing, which includes a screen-printed electrode containing a Prussian blue-gold nanohybrid as the working electrode. The Prussian blue gold nanohybrid is made from polyethylenime (PEI)- mediated simultaneous synthesis of Prussian blue (PBNP) and gold nanoparticles (AuNP), which forms a PBNP-AuNP nanohybrid with a remarkable change in the Prussian blue character. PEI-protected polycrystalline PBNPs can be synthesized in acidic media from the single precursor potassium ferricyanide [K3 Fe(CN)6 ] at 60°C. Since PEI also enables the controlled formation of gold nanoparticles (AuNPs) in the presence of formaldehyde, nanohybrids containing PBNPs and AuNPs may be prepared. Two different methods of PEI mediated synthesis of AuNP in the presence of PBNP were considered. In Method 1, AuNP and PBNP were made independently and mixed together in an appropriate ratio. In Method 2, PBNPs were made first, followed by PEI- and formaldehyde-mediated reduction of gold cations in the presence of PBNP. PBNP-AuNPs display a remarkable change in Prussian blue behavior such that the absorption maxima of PBNP-AuNPs made through Method 1 tend to increase at 670 nm as a function of gold concentration as compared with the control; the reverse was observed when PBNP-AuNPs were made through Method 2. As made PBNPs and PBNP-AuNPs made through Method 1 display excellent catalytic activity toward both reduction and oxidation of hydrogen peroxide based on peroxidase mimetic activity. In addition, the as-synthesized PBNPs displayed superparamagnetic behavior that can be manipulated in the presence of AuNPs. The results from peroxidase mimetic activity, chemiluminescence, cyclic voltammetry, and amperometry showed suitable analytical performance of the as-made PBNP-AuNP nanohybrid for biomedical applications.

Minimally Invasive Platforms in Biosensing.

The interaction of sensing components with body fluids is a basic requirement for clinical diagnostics; a variety of novel platforms have recently been developed for invasive and non-invasive sensing. In this manuscript, recent advancements related to minimally invasive platform for biosensing are reviewed. Many approaches have been utilized for generating minimally invasive platforms that require a small volume of body fluid; for example, the use of small-scale needles known as microneedles for minimally invasive detection has been demonstrated. The use of capillary action in microneedle-assisted biosensing may facilitate the detection of analytes in body fluids. This review considers recent innovations in the structure and performance of minimally invasive sensos.

Molecular weight of polyethylenimine-dependent transfusion and selective antimicrobial activity of functional silver nanoparticles.

Synthetic cationic polymer-mediated synthesis of silver nanoparticles and selective antimicrobial activity of the same were demonstrated. Polyethyleneimine (PEI)-coated silver nanoparticles showed antimicrobial activity against Acinetobacter baumannii as a function of the polymeric molecular weight (MW) of PEI. Silver nanoparticles were coated with PEI of three different MWs: Ag-NP-1 with PEI exhibiting a MW of 750,000, Ag-NP-2 with PEI exhibiting a MW of 1300, and Ag-NP-3 with PEI exhibiting a MW of 60,000. These nanoparticles showed a particle size distribution of 4-20 nm. The nanoparticles exhibited potent antimicrobial activity against A. baumannii, with the minimum inhibitory concentration of Ag-NP-1, Ag-NP-2, and Ag-NP-3 on the order of 5, 10, and 5 µg/mL, respectively, and minimum bactericidal concentration of Ag-NP-1, Ag-NP-2, and Ag-NP-3 on the order of 10, 20, and 10 µg/mL, respectively. Fluorescence imaging of Ag-NPs revealed selective transfusion of Ag-NPs across the cell membrane as a function of the polymeric MW; differential interaction of the cytoplasmic proteins during antimicrobial activity was observed.

Polyethylenimine-mediated synthetic insertion of gold nanoparticles into mesoporous silica nanoparticles for drug loading and biocatalysis.

Mesoporous silica nanoparticles (MSNPs) have been used as an efficient and safe carrier for drug delivery and biocatalysis. The surface modification of MSNPs using suitable reagents may provide a robust framework in which two or more components can be incorporated to give multifunctional capabilities (e.g., synthesis of noble metal nanoparticles within mesoporous architecture along with loading of a bioactive molecule). In this study, the authors reported on a new synthetic route for the synthesis of gold nanoparticles (AuNPs) within (1) unmodified MSNPs and (2) 3-trihydroxysilylpropyl methylphosphonate-modified MSNPs. A cationic polymer, polyethylenimine (PEI), and formaldehyde were used to mediate synthetic incorporation of AuNPs within MSNPs. The AuNPs incorporated within the mesoporous matrix were characterized by transmission electron microscopy, energy dispersive x-ray analysis, and high-resolution scanning electron microscopy. PEI in the presence of formaldehyde enabled synthetic incorporation of AuNPs in both unmodified and modified MSNPs. The use of unmodified MSNPs was associated with an increase in the polycrystalline structure of the AuNPs within the MSNPs. The AuNPs within modified MSNPs showed better catalytic activity than those within unmodified MSNPs. MSNPs with an average size of 200 nm and with a pore size of 4-6 nm were used for synthetic insertion of AuNPs. It was found that the PEI coating enabled AuNPs synthesis within the mesopores in the presence of formaldehyde or tetrahydrofuran hydroperoxide at a temperature between 10 and 25 °C or at 60 °C in the absence of organic reducing agents. The as-made AuNP-inserted MSNPs exhibited enhanced catalytic activity. For example, these materials enabled rapid catalytic oxidation of the o-dianisidine substrate to produce a colored solution in proportion to the amount of H2O2 generated as a function of glucose oxidase-catalyzed oxidation of glucose; a linear concentration range from 80 to 800 µM and a detection limit as low as 80 µM were observed. The mesoscale pores of the as developed AuNP-inserted MSNPs were also used to entrap the hydrophobic drug paclitaxel. The results of this study indicate the potential use of the AuNP-inserted MSNPs in biocatalysis and drug delivery.

Controlled synthesis of polyethylenimine coated gold nanoparticles: Application in glutathione sensing and nucleotide delivery.

Synthesis of functional gold nanoparticles (AuNPs) justifying selectivity in biochemical interaction along with biocompatibility suited for in vivo biomedical applications has been a challenging issue. We report herein the role of polyethylenimine (PEI) in controlled synthesis of AuNPs under ambient conditions which has potentiality for sensing glutathione and selective interaction with DNA binding proteins facilitating endosomal escape for the nucleotide delivery. The choice of organic reducing agents like formaldehyde/acetaldehyde/acetyl acetone/tetrahydrofuran hydroperoxide and other similar compounds allow rapid conversion of PEI capped gold cations into AuNPs at room temperature thus controlling the functional ability of nanoparticles as a function of organic reducing agents. Both small and higher molecular weight PEI facilitates fast synthesis of AuNPs controlling cytotoxicity during in vivo biomedical applications. The AuNPs have been characterized by UV-Vis and transmission electron microscopy revealing excellent polycrystallinity and controlled nanogeometry. The cationic polymer coating enhances the electrocatalytic performances of nanoparticles. The typical biomedical application on glutathione (GSH) sensing based on peroxidase mimetic ability of as made AuNPs is studied. The as synthesized AuNPs are extreme salt and pH resistant and have potentiality for both homogeneous and heterogeneous biocatalysis. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 1191-1199, 2017.

Impact of elevated temperatures on specific leaf weight, stomatal density, photosynthesis and chlorophyll fluorescence in soybean.

High-temperature stress is a major environmental stress and there are limited studies elucidating its impact on soybean (Glycine max L. Merril.). The objectives of present study were to quantify the effect of high temperature on changes in leaf thickness, number of stomata on adaxial and abaxial leaf surfaces, gas exchange, chlorophyll fluorescence parameters and seed yield in soybean. Twelve soybean genotypes were grown at day/night temperatures of 30/22, 34/24, 38/26 and 42/28 °C with an average temperature of 26, 29, 32 and 35 °C, respectively, under greenhouse conditions. One set was also grown under ambient temperature conditions where crop season average maximum, minimum and mean temperatures were 28.0, 22.4 and 25.2 °C, respectively. Significant negative effect of temperature was observed on specific leaf weight (SLW) and leaf thickness. Rate of photosynthesis, stomatal conductance and water use efficiency declined as the growing temperatures increased; whereas, intercellular CO2 and transpiration rate were increased. With the increase in temperature chlorophyll fluorescence parameters such as Fv/Fm, qP and PhiPSII declined while there was increase in qN. Number of stomata on both abaxial and adaxial surface of leaf increased significantly with increase in temperatures. The rate of photosynthesis, PhiPSII, qP and SPAD values were positively associated with leaf thickness and SLW. This indicated that reduction in photosynthesis and associated parameters appears to be due to structural changes observed at higher temperatures. The average seed yield was maximum (13.2 g/pl) in plants grown under ambient temperature condition and declined by 8, 14, 51 and 65% as the temperature was increased to 30/22, 34/24, 38/26 and 42/28 °C, respectively.

Role of Organic Carbonyl Moiety and 3-Aminopropyltrimethoxysilane on the Synthesis of Gold Nanoparticles Specific to pH- and Salt-Tolerance.

The synthesis of gold nanoparticles (AuNPs) having better dispersibility and catalytic ability than the conventional AuNPs is the challenging task. The fact that aldehydes and ketones results in the formation of catalytic hybrid material with amino functionalized silanes directed the use of carbonyl functional group (aldehydes and ketones) specifically formaldehyde, acetaldehyde, acetone and t-butyl methyl ketone alongwith 3-aminopropyltrimethoxysilane (3-APTMS) to meet such requirement. Accordingly, a comparative study on the synthesis of 3-APTMS and organic reducing agent mediated synthesis of AuNPs are reported herein. The findings reveal that 3-APTMS capped gold ions are converted into AuNPs with precise control of pH- and salt- sensitivity. The major findings reveal the following: (1) 3-APTMS being amphiphilic, dispersibility of as prepared AuNPs largely depends on the organic reducing agents. (2) An increase in the hydrocarbon content of the reducing agent facilitate the dispersibility of AuNPs in organic solvent whereas decrease of the same increases the dispersibility in water, (3) AuNPs made through aldehydic reducing agents (formaldehyde and acetaldehyde) have relatively better salt and pH tolerance as compared to ketonic reducing agents (acetone, t-butyl methyl ketone), and (4) an increase in 3-APTMS concentrations imparts better salt- and pH- resistant property to AuNPs irrespective of organic reducing agents. A typical example on the role of AuNPs in homogeneous catalysis during potassium ferricyanide mediated oxidation of ascorbic acid is also reported.

Experimental Hepatotoxicity Produced by Ethinyl estradiol.

Ethinyl oestradiol (EO) is the most commonly used as a component of oral contraceptive and hormonal replacement therapy (HRT) in women. However, its excessive and prolonged use may cause cytotoxicity, including cancer of many organs. Hence, the present study was performed to produce the experimental hepatotoxicity in female albino rats. EO was administered to different groups of rats, respectively @ 250, 500 and 750 µg/kg body weight, orally, weekly for 16 and 20 weeks. One group of rats was administered with saline alone to serve as control. The rats were sacrificed after their respective experimental periods, and the livers were collected and preserved in 10% buffered formalin. Later on, the histopathological study of liver tissues was done. On the 17(th) week, the hepatic tissues showed severe congestion, focal areas of hemorrhage, extreme vacuolation of cytoplasm, distended sinusoids with dilated central veins. Degeneration and necrosis of hepatocytes as evidenced by increased cytoplasmic granularity, and dissolution of nuclear materials were seen. On the 21(st) weeks, these changes were extremely severe and quite conspicuous. Distinct fibrosis was also noticed. EO caused hepatotoxicity, the extent and severity of which were dose and time dependent, indicating that this drug at higher dose after prolonged duration (500 or 750 µg/kg, orally, weekly for 20 weeks) may cause the standard experimental hepatotoxicity in rats.