Modulation of early osteoarthritis by tibiofemoral re-alignment in sheep.

OBJECTIVE: To investigate whether tibiofemoral alignment influences early knee osteoarthritis (OA). We hypothesized that varus overload exacerbates early degenerative osteochondral changes, and that valgus underload diminishes early OA. METHOD: Normal, over- and underload were induced by altering alignment via high tibial osteotomy in adult sheep (n = 8 each). Simultaneously, OA was induced by partial medial anterior meniscectomy. At 6 weeks postoperatively, OA was examined in five individual subregions of the medial tibial plateau using Kellgren-Lawrence grading, quantification of macroscopic OA, semiquantitative histopathological OA and immunohistochemical type-II collagen, ADAMTS-5, and MMP-13 scoring, biochemical determination of DNA and proteoglycan contents, and micro-computed tomographic evaluation of the subchondral bone. RESULTS: Multivariate analyses revealed that OA cartilaginous changes had a temporal priority over subchondral bone changes. Underload inhibited early cartilage degeneration in a characteristic topographic pattern (P ≥ 0.0983 vs. normal), in particular below the meniscal damage, avoided alterations of the subarticular spongiosa (P ≥ 0.162 vs. normal), and prevented the disturbance of otherwise normal osteochondral correlations. Overload induced early alterations of the subchondral bone plate microstructure towards osteopenia, including significantly decreased percent bone volume and increased bone surface-to-volume ratio (all P ≤ 0.0359 vs. normal). CONCLUSION: The data provide high-resolution evidence that tibiofemoral alignment modulates early OA induced by a medial meniscus injury in adult sheep. Since underload inhibits early OA, these data also support the clinical value of strategies to reduce the load in an affected knee compartment to possibly decelerate structural OA progression.

A systematic approach to managing complications after proximal tibial osteotomies of the knee.

Proximal tibial osteotomy (PTO) is an effective procedure for active and young adult patients with symptomatic unicompartmental osteoarthritis and malalignment. They were considered technically demanding and prone to various complications related to the surgical technique, biomechanical or biological origin. Among the most important are hinge fractures and delayed or non-healing, neurovascular complications, loss of correction, implant-related problems, patellofemoral complaints, biological complications and changes in limb length. Being aware of these problems can help minimizing their prevalence and improve the results of the procedure.The aim of this narrative review is to discuss the potential complications that may occur during and after proximal tibial osteotomies, their origin and ways to prevent them.

Quantifying the Human Subchondral Trabecular Bone Microstructure in Osteoarthritis with Clinical CT.

Osteoarthritis (OA) is characterized by critical alterations of the subchondral bone microstructure, besides the well-known cartilaginous changes. Clinical computed tomography (CT) detection of quantitative 3D microstructural subchondral bone parameters is applied to monitor changes of subchondral bone structure in different stages of human OA and is compared with micro-CT, the gold standard. Determination by clinical CT (287 µm resolution) of key microstructural parameters in tibial plateaus with mild-to-moderate and severe OA reveals strong correlations to micro-CT (35 µm), high inter- and intraobserver reliability, and small relative differences. In vivo, normal, mild-to-moderate, and severe OA are compared with clinical CT (331 µm). All approaches detect characteristic expanded trabecular structure in severe OA and fundamental microstructural correlations with clinical OA stage. Multivariate analyses at various in vivo and ex vivo imaging resolutions always reliably separate mild-to-moderate from severe OA (except mild-to-moderate OA from normal), revealing a striking similarity between 287 µm clinical and 35 µm micro-CT. Thus, accurate structural measurements using clinical CT with a resolution near the trabecular dimensions are possible. Clinical CT offers an opportunity to quantitatively monitor subchondral bone microstructure in clinical and experimental settings as an advanced tool of investigating OA and other diseases affecting bone architecture.

Axial alignment is a critical regulator of knee osteoarthritis.

Although osteoarthritis (OA), a leading cause of disability, has been associated with joint malalignment, scientific translational evidence for this link is lacking. In a clinical case study, we provide evidence of osteochondral recovery upon unloading symptomatic isolated medial tibiofemoral knee OA associated with varus malalignment. By mapping response correlations at high resolution, we identify spatially complex degenerative changes in cartilage after overloading in a clinically relevant ovine model. We further report that unloading diminishes OA cartilage degeneration and alterations of critical parameters of the subchondral bone plate in a similar topographic fashion. Last, therapeutic unloading shifted the articular cartilage and subchondral bone phenotype to normal and restored several physiological correlations disturbed in neutral and varus OA, suggesting a protective effect on the integrity of the entire osteochondral unit. Collectively, these findings identify modifiable trajectories with considerable translational potential to reduce the burden of human OA.

The portal of Neviaser: a valid option for antegrade nailing of humerus fractures.

INTRODUCTION: The objective of this retrospective non-randomized study was to evaluate the portal of Neviaser (PN) as an alternative approach in antegrade humeral nailing. METHODS: The surgical approach for the straight antegrade intramedullary nail (SAIN) was either the anterolateral delta-split (group 2, n = 79) or the portal of Neviaser (group 3, n = 27). Length of surgery and time of radiation were extracted from charts. Patients stabilized using the PN were followed for a clinical and radiological exam. At follow-up we evaluated the DASH (Disability of the Arm, Shoulder and Hand) and CMS (Constant-Murley Score). RESULTS: Between 10.2015 and 12.2018 191 proximal and diaphyseal humeral fractures were operated using either an angular stable extramedullary device (group 1, PHILOS®, n = 85) or a straight humeral nail (MultiLoc®, n = 106). Time of radiation and intervention followed a normal distribution. The mean length of surgery was 172.9 min (SD 91.5) in group 1, 121.5 min (SD 54.1) in group 2 and 96.4 min (SD 33.7) in group 3 (p < 0.01). Time of radiation was significantly different with 1.1 min (SD 0.6: group 1), 3.1 min (SD 1.6: group 2) and 2.9 min (SD 1.7: group 3) (p < 0.01). After a mean interval of 21.5 months (range 6-43 months) 14 / 27 patients of group 3 were available for a clinical and radiological follow-up. The mean DASH in group 3 was 25, the CMS reached 70. The age and sex weighted CMS mean value was 96%. Forward flexion was 131°, abduction 125°. The ratio of strength affected versus non-affected side was 4.4: 6.2 kg. CONCLUSIONS: The portal of Neviaser is a feasible and safe approach and is an alternative to the anterolateral delta-split. Length of surgery and time of radiation were significantly shorter. LEVEL OF EVIDENCE: IV.

Ramp lesions of the medial meniscus are associated with a higher grade of dynamic rotatory laxity in ACL-injured patients in comparison to patients with an isolated injury.

PURPOSE: The purpose of this study was to compare preoperative knee laxity between two groups of patients with primary or revision ACL reconstruction with or without an associated ramp lesion of the medial meniscus. METHODS: Two-hundred and seventy-five patients with an ACL reconstruction (243 primaries; 32 revisions) were prospectively screened using direct arthroscopic visualisation and divided into a ramp lesion group (RLG) and a control group (CG) regardless of the presence of other associated meniscal tears. All patients were clinically examined under anaesthesia before surgery by grading the Lachman and pivot shift tests. RESULTS: Fifty-eight patients were included in the RLG. The CG included 217 patients. With all meniscus lesions included, there were no significant differences between the two groups. After excluding all other meniscus lesions in both groups except for ramp lesions in the RLG, the prevalence of a grade III pivot shift was higher in the RLG (32 remaining patients; 47% grade III) compared to the CG (91 remaining patients; 24% grade III, p = 0.02). The difference of patients with a grade III pivot shift between the CG and RLG remained significant after removal of revision ACL reconstructions (CG, 85 remaining patients; 25% grade III-RLG, 27 remaining patients; 44% grade III, p = 0.05). CONCLUSION: Patients with an isolated ramp lesion of the medial meniscus in association with an ACL injury displayed a higher amount of dynamic rotational laxity as expressed by the pivot shift test in comparison to patients with isolated ACL injury and no ramp lesion. The association between ramp lesions of the medial meniscus and increased pivot shift grading suggests that it is important to diagnose and repair them during ACL reconstruction surgery. LEVEL OF EVIDENCE: III.

Younger age and hamstring tendon graft are associated with higher IKDC 2000 and KOOS scores during the first year after ACL reconstruction.

PURPOSE: Although reference values in healthy subjects have been published for both the International Knee Documentation Committee 2000 subjective knee form (IKDC 2000) and the Knee injury and Osteoarthritis Outcome Score (KOOS), data obtained during the first year after anterior cruciate ligament reconstruction (ACL-R) are sparse. The aim was to establish patient reference values for both questionnaires at different time points and depending on nine individual patient characteristics during the first year after ACL-R. METHODS: Prospectively recorded data from a hospital-based registry were retrospectively extracted from the database. IKDC 2000 and KOOS questionnaires were self-administered pre-operatively and 6 weeks, 3 months, and 6 and 12 months following primary ACL-R. Score values were compared according to nine individual patient criteria: gender, age, body mass index, level of activity, involvement in competition, previous contralateral knee injury and/or surgery, graft type, meniscal repair and/or cartilage lesions. The feature which had a significant and consistent impact on the outcomes was considered as main reference. RESULTS: Two-hundred and nighty-eight patients met the inclusion criteria. Overall, the score values increased over time after ACL-R. At 12 months, they were significantly greater than at any other time point (p < 0.05). The main individual feature influencing the IKDC 2000 score was age. Patients below 30 years of age had up to 9 points higher IKDC 2000 score values at all time points (p < 0.05). The main individual characteristic influencing the KOOS score was graft type. Patients with hamstring tendon grafts (STGR) had up to 15 points higher KOOS score values than patients with bone-patellar tendon-bone (BPTB) grafts during the first months after ACL-R (p < 0.05). At 12 months, no differences in KOOS score values could be identified anymore. CONCLUSIONS: Younger age (< 30 years) and STGR grafts were related to higher IKDC 2000 and KOOS score values within the first year after primary ACL-R. The patient reference values adjusted to age and graft provided in this study may help to identify patients with lower outcomes within the first year after ACL-R. LEVEL OF EVIDENCE: Level III.

Mechanical strength of a new plate compared to six previously tested opening wedge high tibial osteotomy implants.

BACKGROUND: This study aimed to assess the mechanical static and fatigue strength provided by the FlexitSystem plate in medial opening wedge high tibial osteotomies (MOWHTO), and to compare it to six previously tested implants: the TomoFix small stature, the TomoFix standard, the ContourLock, the iBalance, the second generation PEEKPower and the size 2 Activmotion. Thus, this will provide surgeons with data that will help in the choice of the most appropriate implant for MOWHTO. METHODS: Six fourth-generation tibial bone composites underwent a MOWHTO and each was fixed using six FlexitSystem plates, according to standard techniques. The same testing procedure that has already been previously defined, used and published, was used to investigate the static and dynamic strength of the prepared bone-implant constructs. The test consisted of static loading and cyclical loading for fatigue testing. RESULTS: During static testing, the group constituted by the FlexitSystem showed a fracture load higher than the physiological loading of slow walking (3.7 kN > 2.4 kN). Although this fracture load was relatively small compared to the average values for the other Implants from our previous studies, except for the TomoFix small stature and the Contour Lock. During fatigue testing, FlexitSystem group showed the smallest stiffness and higher lifespan than the TomoFix and the PEEKPower groups. CONCLUSIONS: The FlexitSystem plate showed sufficient strength for static loading, and average fatigue strength compared to the previously tested implants. Full body dynamic loading of the tibia after MOWHTO with the investigated implants should be avoided for at least 3 weeks. Implants with a wider T-shaped proximal end, positioned onto the antero-medial side of the tibia head, or inserted in the osteotomy opening in a closed-wedge construction, provided higher mechanical strength than implants with small a T-shaped proximal end, centred onto the medial side of the tibia head.

The biomechanical effects of allograft wedges used for large corrections during medial opening wedge high tibial osteotomy.

The inclusion of an allograft wedge during medial opening wedge high tibial osteotomy has been shown to lead to satisfactory time-to-union in larger corrections (>10°). Such large corrections are associated with greater incidences of intraoperative hinge fracture and reduced construct stability. The purpose of this study was to investigate the biomechanical stability that an allograft wedge brings to an osteotomy. Ten medium-size fourth generation artificial sawbone tibiae underwent 12 mm biplanar medial opening wedge high tibial osteotomy with a standard Tomofix plate. Five tibiae had an allograft wedge inserted into the osteotomy gap prior to plate fixation (allograft group). The gap in the remaining tibiae was left unfilled (control group). Each group underwent static compression testing and cyclical fatigue testing until failure of the osteotomy. Peak force, valgus malrotation, number of cycles, displacement and stiffness around the tibial head were analysed. Intraoperative hinge fractures occurred in all specimens. Under static compression, the allograft group withstood higher peak forces (6.01 kN) compared with the control group (5.12 kN). Valgus malrotation was lower, and stiffness was higher, in the allograft group. During cyclical fatigue testing, results within the allograft group were more consistent than within the control group. This may indicate more predictable results in large osteotomies with an allograft. Tibial osteotomies with allograft wedges appear beneficial for larger corrections, and in cases of intraoperative hinge fracture, due to the added construct stability they provide, and the consistency of results compared with tibial osteotomies without a graft.

Graft materials provide greater static strength to medial opening wedge high tibial osteotomy than when no graft is included.

BACKGROUND: The purpose of this study was to compare the stability of medial opening-wedge high tibial osteotomy (MOWHTO) with and without different graft materials. Good clinical and radiological outcomes have been demonstrated when either using or not using graft materials during MOWHTO. Variations in the biomechanical properties of different graft types, regarding the stability they provide a MOWHTO, have not been previously investigated. METHODS: A 10 mm biplanar MOWHTO was performed on 15 artificial sawbone tibiae, which were fixed using the Activmotion 2 plate. Five bones had OSferion60 wedges (synthetic group), five had allograft bone wedges (allograft group), and five had no wedges (control group) inserted into the osteotomy gap. Static compression was applied axially to each specimen until failure of the osteotomy. Ultimate load, horizontal and vertical displacements were measured and used to calculate construct stiffness and valgus malrotation of the tibial head. RESULTS: The synthetic group failed at 6.3 kN, followed by the allograft group (6 kN), and the control group (4.5 kN). The most valgus malrotation of the tibial head was observed in the allograft group (2.6°). The synthetic group showed the highest stiffness at the medial side of the tibial head (9.54 kN·mm- 1), but the lowest stiffness at the lateral side (1.59 kN·mm-1). The allograft group showed high stiffness on the medial side of the tibial head (7.54 kN·mm- 1) as well as the highest stiffness on the lateral side (2.18 kN·mm- 1). CONCLUSIONS: The use of graft materials in MOWHTO results in superior material properties compared to the use of no graft. The static strength of MOWHTO is highest when synthetic grafts are inserted into the osteotomy gap. Allograft wedges provide higher mechanical strength to a MOWHTO than when no graft used. In comparison to the synthetic grafts, allograft wedges result in the stiffness of the osteotomy being more similar at the medial and lateral cortices.

Advances in modern osteotomies around the knee : Report on the Association of Sports Traumatology, Arthroscopy, Orthopaedic surgery, Rehabilitation (ASTAOR) Moscow International Osteotomy Congress 2017.

Corrective lower limb osteotomies are innovative and efficient therapeutic procedures for restoring axial alignment and managing unicompartmental knee osteoarthritis. This review presents critical insights into the up-dated clinical knowledge on osteotomies for complex posttraumatic or congenital lower limb deformities with a focus on high tibial osteotomies, including a comprehensive overview of basic principles of osteotomy planning, biomechanical considerations of different implants for osteotomies and insights in specific bone deformity correction techniques. Emphasis is placed on complex cases of lower limb osteotomies associated with ligament and multiaxial instability including pediatric cases, computer-assisted navigation, external fixation for long bone deformity correction and return to sport after such osteotomies. Altogether, these advances in the experimental and clinical knowledge of complex lower limb osteotomies allow generating improved, adapted therapeutic regimens to treat congenital and acquired lower limb deformities.

Anterior buttress plate is successful for treating posterior sterno-clavicular dislocation.

PURPOSE: Traumatic posterior instability of the sternoclavicular joint is a potentially life-threatening injury. In contrast to the low incidence there is a plethora of different strategies to treat this lesion. It was the objective of this retrospective analysis to evaluate and further develop current strategies. METHODS: In this retrospective analysis all posterior dislocations that were diagnosed and treated between 2011 and 2018 were included. In this 7 year period, eight male patients (median age 32 years) were operated. RESULTS: Three patients were not diagnosed at the primary institution and were referred later. Five patients were treated with an anterior buttress plate with clavicular stabilisation only. One patient was stabilized with a temporary sternoclavicular arthrodesis. Two patients were operated using an autologous tendon graft. All of the patients underwent an immediate postoperative CT-scan that documented the anatomical articulation. All patients treated with a plate underwent implant removal. A final CT examination after removal documented the maintenance of the anatomic alignment. CONCLUSIONS: The buttress plate technique with clavicular screw fixation is a sufficient treatment to restore and preserve a normal sternoclavicular alignment. The technique finds its indication in unidirectional posterior instability. LEVEL OF EVIDENCE: IV.

Numerical comparative study of five currently used implants for high tibial osteotomy: realistic loading including muscle forces versus simplified experimental loading.

BACKGROUND: Many different fixation devices are used to maintain the correction angle after medial open wedge high tibial osteotomy (MOWHTO). Each device must provide at least sufficient mechanical stability to avoid loss of correction and unwanted fracture of the contralateral cortex until the bone heals. In the present study, the mechanical stability of following different implants was compared: the TomoFix small stature (sm), the TomoFix standard (std), the Contour Lock, the iBalance and the second generation PEEKPower. Simplified loading, usually consisting of a vertical load applied to the tibia plateau, is used for experimental testing of fixation devices and also in numerical studies. Therefore, this study additionally compared this simplified experimental loading with a more realistic loading that includes the muscle forces. METHOD: Two types of finite element models, according to the considered loading, were created. The first type numerically simulated the static tests of MOWHTO implants performed in a previous experimental biomechanical study, by applying a vertical compressive load perpendicularly to the plateau of the osteotomized tibia. The second type included muscle forces in finite element models of the lower limb with osteotomized tibiae and simulated the stance phase of normal gait. Section forces in the models were determined and compared. Stresses in the implants and contralateral cortex, and micromovements of the osteotomy wedge, were calculated. RESULTS: For both loading types, the stresses in the implants were lower than the threshold values defined by the material strength. The stresses in the lateral cortex were smaller than the ultimate tensile strength of the cortical bone. The implants iBalance and Contour Lock allowed the smallest micromovements of the wedge, while the PEEKPower allowed the highest. There was a correlation between the micromovements of the wedge, obtained for the simplified loading of the tibia, and the more realistic loading of the lower limb at 15% of the gait cycle (Pearson's value r = 0.982). CONCLUSIONS: An axial compressive load applied perpendicularly to the tibia plateau, with a magnitude equal to the first peak value of the knee joint contact forces, corresponds quite well to a realistic loading of the tibia during the stance phase of normal gait (at 15% of the gait cycle and a knee flexion of about 22 degrees). However, this magnitude of the knee joint contact forces overloads the tibia compared to more realistic calculations, where the muscle forces are considered. The iBalance and Contour Lock implants provide higher rigidity to the bone-implant constructs compared to the TomoFix and the PEEKPower plates.

Ramp lesions associated with ACL injuries are more likely to be present in contact injuries and complete ACL tears.

PURPOSE: The purpose of this study was to analyse patient and injury characteristics as well as arthroscopic findings in a prospective cohort of ACL-injured patients with or without an associated ramp lesion. METHODS: Two hundred and twenty-four patients undergoing a primary (n = 196) or revision (n = 28) ACL reconstruction were included. The presence of a ramp lesion was determined by a systematic arthroscopic inspection of the posteromedial compartment. Chi-square tests were used to compare the population of ACL-injured patients with and without a ramp lesion regarding sex, age, body mass index, previous ACL injuries, sport before injury, and injury characteristics. Significance was set at p < 0.05. RESULTS: Fifty-three out of 224 patients had a ramp lesion (24%). The presence of the latter was not related to any of the analysed patient characteristics. The prevalence of the lesion was higher in contact injuries (n = 19; 41%) compared with non-contact injures (n = 34; 19%; p < 0.001). It was higher in patients with complete ACL ruptures (n = 49; 27%) as opposed to partial ruptures (n = 1; 4%; p = 0.01). A patient was 2.98 [95% CI 1.49-5.98] times more likely to have a ramp lesion if the ACL injury was declared to have been caused by direct contact and 8.71 [95% CI 1.15-66.12] times more likely if the ACL tear was complete. CONCLUSION: Ramp lesions may be anticipated in almost one out of four patients undergoing ACL reconstruction, especially if a patient sustained a contact injury and in the presence of a complete ACL tear. LEVEL OF EVIDENCE: III.

A finite element model of the lower limb during stance phase of gait cycle including the muscle forces.

BACKGROUND: Results of finite element (FE) analyses can give insight into musculoskeletal diseases if physiological boundary conditions, which include the muscle forces during specific activities of daily life, are considered in the FE modelling. So far, many simplifications of the boundary conditions are currently made. This study presents an approach for FE modelling of the lower limb for which muscle forces were included. METHODS: The stance phase of normal gait was simulated. Muscle forces were calculated using a musculoskeletal rigid body (RB) model of the human body, and were subsequently applied to a FE model of the lower limb. It was shown that the inertial forces are negligible during the stance phase of normal gait. The contact surfaces between the parts within the knee were modelled as bonded. Weak springs were attached to the distal tibia for numerical reasons. RESULTS: Hip joint reaction forces from the RB model and those from the FE model were similar in magnitude with relative differences less than 16%. The forces of the weak spring were negligible compared to the applied muscle forces. The maximal strain was 0.23% in the proximal region of the femoral diaphysis and 1.7% in the contact zone between the tibia and the fibula. CONCLUSIONS: The presented approach based on FE modelling by including muscle forces from inverse dynamic analysis of musculoskeletal RB model can be used to perform analyses of the lower limb with very realistic boundary conditions. In the present form, this model can be used to better understand the loading, stresses and strains of bones in the knee area and hence to analyse osteotomy fixation devices.

Static and fatigue strength of a novel anatomically contoured implant compared to five current open-wedge high tibial osteotomy plates.

BACKGROUND: The purpose of the present study was to compare the mechanical static and fatigue strength of the size 2 osteotomy plate "Activmotion" with the following five other common implants for the treatment of medial knee joint osteoarthritis: the TomoFix small stature, the TomoFix standard, the Contour Lock, the iBalance and the second generation PEEKPower. METHODS: Six fourth-generation tibial bone composites underwent a medial open-wedge high tibial osteotomy (HTO), according to standard techniques, using size 2 Activmotion osteotomy plates. All bone-implant constructs were subjected to static compression load to failure and load-controlled cyclic fatigue failure testing, according to a previously defined testing protocol. The mechanical stability was investigated by considering different criteria and parameters: maximum forces, the maximum number of loading cycles, stiffness, the permanent plastic deformation of the specimens during the cyclic fatigue tests, and the maximum displacement range in the hysteresis loops of the cyclic loading responses. RESULTS: In each test, all bone-implant constructs with the size 2 Activmotion plate failed with a fracture of the lateral cortex, like with the other five previously tested implants. For the static compression tests the failure occurred in each tested implant above the physiological loading of slow walking (> 2400 N). The load at failure for the Activmotion group was the highest (8200 N). In terms of maximum load and number of cycles performed prior to failure, the size 2 Activmotion plate showed higher results than all the other tested implants except the ContourLock plate. The iBalance implant offered the highest stiffness (3.1 kN/mm) for static loading on the lateral side, while the size 2 Activmotion showed the highest stiffness (4.8 kN/mm) in cyclic loading. CONCLUSIONS: Overall, regarding all of the analysed strength parameters, the size 2 Activmotion plate provided equivalent or higher mechanical stability compared to the previously tested implant. Implants with a metaphyseal slope adapted to the tibia anatomy, and positioned more anteriorly on the proximal medial side of the tibia, should provide good mechanical stability.

Mechanical strength assessment of a drilled hole in the contralateral cortex at the end of the open wedge for high tibial osteotomy.

BACKGROUND: This study aimed to investigate, by means of finite element analysis, the effect of a drill hole at the end of a horizontal osteotomy to reduce the risk of lateral cortex fracture while performing an opening wedge high tibial osteotomy (OWHTO). The question was whether drilling a hole relieves stress and increases the maximum correction angle without fracture of the lateral cortex depending on the ductility of the cortical bone. METHODS: Two different types of osteotomy cuts were considered; one with a drill hole (diameter 5 mm) and the other without the hole. The drill holes were located about 20 mm distally to the tibial plateau and 6 mm medially to the lateral cortex, such that the minimal thickness of the contralateral cortical bone was 5 mm. Based on finite element calculations, two approaches were used to compare the two types of osteotomy cuts considered: (1) Assessing the static strength using local stresses following the idea of the FKM-guideline, subsequently referred to as the "FKM approach" and (2) limiting the total strain during the opening of the osteotomy wedge, subsequently referred to as "strain approach". A critical opening angle leading to crack initiation in the opposite lateral cortex was determined for each approach and was defined as comparative parameter. The relation to bone aging was investigated by considering the material parameters of cortical bones from young and old subjects. RESULTS: The maximum equivalent (von-Mises) stress was smaller for the cases with a drill hole at the end of the osteotomy cut. The critical angle was approximately 1.5 times higher for the specimens with a drill hole compared to those without. This corresponds to an average increase of 50%. The calculated critical angle for all approaches is below 5°. The critical angle depends on the used approach, on patient's age and assumed ductility of the cortical bone. CONCLUSIONS: Drilling a hole at the end of the osteotomy reduces the stresses in the lateral cortex and increases the critical opening angle prior to cracking of the opposite cortex in specimen with small correction angles. But the difference from having a drill hole or not is not so significant, especially for older patients. The ductility of the cortical bone is the decisive parameter for the critical opening angle.

The Impact of Osseous Malalignment and Realignment Procedures in Knee Ligament Surgery: A Systematic Review of the Clinical Evidence.

BACKGROUND: Failure rates of knee ligament surgery may be high, and the impact of osseous alignment on surgical outcome remains controversial. Basic science studies have demonstrated that osseous malalignment can negatively affect ligament strain and that realignment procedures may improve knee joint stability. HYPOTHESIS/PURPOSE: The purpose of this review was to summarize the clinical evidence concerning the impact of osseous malalignment and realignment procedures in knee ligament surgery. The hypotheses were that lower extremity malalignment would be an important contributor to knee ligament surgery failure and that realignment surgery would contribute to increased knee stability and improved outcome in select cases. STUDY DESIGN: Systematic review; Level of evidence, 4. METHODS: According to the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) guidelines, a systematic electronic search of the PubMed database was performed in November 2015 to identify clinical studies investigating (A) the influence of osseous alignment on postoperative stability and/or failure rates after knee ligament surgery and (B) the impact of osseous realignment procedures in unstable knees with or without additional knee ligament surgery on postoperative knee function and stability. Methodological quality of the studies was assessed using the Oxford Centre for Evidence-Based Medicine Levels of Evidence and the Coleman Methodological Score (CMS). RESULTS: Of the 1466 potentially relevant articles, 28 studies fulfilled the inclusion and exclusion criteria. Average study quality was poor (CMS, 40). For part A, studies showed increased rerupture rate after anterior cruciate ligament (ACL) replacement in patients with increased tibial slope. Concerning the posterior cruciate ligament (PCL)/posterolateral corner (PLC)/lateral collateral ligament (LCL), varus malalignment was considered a significant risk factor for failure. For part B, studies showed decreased anterior tibial translation after slope-decreasing high tibial osteotomy in ACL-deficient knees. Correcting varus malalignment in PCL/PLC/LCL instability also showed increased stability and better outcomes. CONCLUSION: In cases of complex knee instability, the 3-dimensional osseous alignment of the knee should be considered (eg, mechanical weightbearing line and tibial slope). In cases of failed ACL reconstruction, the tibial slope should be considered, and slope-reducing osteotomies are often helpful in the patient revised multiple times. In cases of chronic PCL and/or PLC instability, osseous correction of the varus alignment may reduce the failure rate and is often the first step in treatment. Changes in the mechanical axis should be considered in all cases of instability accompanied by early unicompartmental osteoarthritis.

Surgical anatomy of medial open-wedge high tibial osteotomy: crucial steps and pitfalls.

PURPOSE: To give an overview of the basic knowledge of the functional surgical anatomy of the proximal lower leg and the popliteal region relevant to medial high tibial osteotomy (HTO) as key anatomical structures in spatial relation to the popliteal region and the proximal tibiofibular joint are usually not directly visible and thus escape a direct inspection. METHODS: The surgical anatomy of the human proximal lower leg and its relevance for HTO are illustrated with a special emphasis on the individual steps of the operation involving creation of the osteotomy planes and plate fixation. RESULTS: The posteriorly located popliteal neurovascular bundle, but also lateral structures such as the peroneal nerve, the head of the fibula and the lateral collateral ligament must be protected from the instruments used for osteotomy. Neither positioning the knee joint in flexion, nor the posterior thin muscle layer of the popliteal muscle offers adequate protection of the popliteal neurovascular bundle when performing the osteotomy. Tactile feedback through a loss-of-resistance when the opposite cortex is perforated is only possible when sawing and drilling is performed in a pounding fashion. Kirschner wires with a proximal thread, therefore, always need to be introduced under fluoroscopic control. Due to anatomy of the tibial head, the tibial slope may increase inadvertently. CONCLUSIONS: Enhanced surgical knowledge of anatomical structures that are at a potential risk during the different steps of osteotomy or plate fixation will help to avoid possible injuries. LEVEL OF EVIDENCE: Expert opinion, Level V.