Understanding the Trap Characteristics of Perovskite Solar Cells via Drive-Level Capacitance Profiling.

Perovskite solar cells (PSCs) are gaining significant interest as the future of photovoltaics owing to their superior performance and cost-effectiveness. Nevertheless, traps in PSCs have emerged as issues that adversely affect the efficiency and stability of the devices. In this study, the methylammonium chloride (MACl) additive and phenyltrimethylammonium iodide (PTMAI) posttreatment were applied to passivate bulk and surface defects. Furthermore, variations of the traps' quantitative spatial arrangement have been monitored by using the drive-level capacitance profiling (DLCP) analysis. A similar magnitude of trap reduction was observed for the bulk perovskite layer and two interfaces (electron transport layer (ETL)/perovskite and hole transport layer (HTL)/perovskite) with an optimal concentration of the MACl additive. However, the effect of perovskite posttreatment in reducing the trap density was much more noticeable at the HTL/perovskite interface compared to the bulk and ETL/perovskite regions. This observation was reinforced by the outcomes of the 500 h thermal stability tests at 60 °C from seven independent batches, which demonstrated a substantial suppression of trap accumulation, particularly at the HTL/perovskite interface, by an order of magnitude.

Thermal degradation of the bulk and interfacial traps at 85 °C in perovskite photovoltaics.

The facile formation of defects in halide perovskite has recently been regarded as the main bottleneck for both the efficiency and stability of perovskite solar cells (PSCs). Therefore, understanding and controlling defects and traps in PSCs is essential to achieving stable devices. Herein, the thermal degradation of perovskite solar cells at 85 °C is studied in terms of electronic traps and device performance, of which the correlations are discussed. In particular, the shifts and changes in both energetic and spatial distributions of electronic defects are observed by capacitance plus impedance analyses under thermal stress. As the energy level and density of deep traps are quantitatively investigated, both the relaxation and degradation of the traps are identified at different timescales. Additionally, the trap densities are individually traced by positions during thermal degradation, where distinct evolutions are visualized. Notably, the traps are measured dominant at the interface between the perovskite and electron-transport layer (ETL). However, LiF incorporation mitigates the electronic traps by an order of magnitude at both interfaces throughout the thermal degradation, indicating that LiF incorporation reduces the initial trap density and suppresses the further formation of traps near the interfaces.

Identifying the Association between Surface Heterogeneity and Electrochemical Properties in Graphite.

Graphite materials for commercial Li-ion batteries usually undergo special treatment to control specific parameters such as particle size, shape, and surface area to have desirable electrochemical properties. Graphite surfaces can be classified into basal and edge planes in the aspect of the structure of carbons, with the existing defect sites such as functional groups and dislocations. The solid-electrolyte interphase (SEI) mostly forms at the edge plane and defect sites, as Li-ions only intercalate through these non-basal planes, whereas the electrochemical properties of graphite largely depend on its surface heterogeneity due to the difference of reactivity on each plane. In order to quantify the detailed surface structure of graphite materials, local-absorption isotherms were utilized, and the analyzed nanostructural parameters of various commercial graphite samples were correlated with the electrochemical properties of each graphite anode. Thereby, we have confirmed that the fraction of non-basal plane and fast-charging capability has strong linear relations. The pore/non-basal sites are also related to the cycle life by affecting the SEI formation, and the determination of surface heterogeneity and pores of graphite materials can provide powerful parameters that imply the electrochemical performances of commercial graphite.

Incorporation of Lithium Fluoride Restraining Thermal Degradation and Photodegradation of Organometal Halide Perovskite Solar Cells.

Because of the facile formation of defects in organometal halide perovskites, the defect passivation has become an important prerequisite for the stable and efficient perovskite solar cell (PSC). Regarding that ionic defects of the perovskites play a significant role on the performance and stability of PSCs, we introduce lithium fluorides as effective passivators based on their strong ionic characteristics and small ionic radii. Both Li+ and F- are observed to successfully incorporate within the perovskite layer, improving the device performances with the best efficiency over 20%, while the hysteresis effects are significantly reduced, confirming the passivation of perovskite defects. Moreover, LiF restrains both thermal degradation and photodegradation of PSCs, where over 90% of the initial efficiencies have been retained by LiF-incorporated devices for more than 1000 h under either 1 sun illumination or 85 °C thermal condition. As the trap density of states is analyzed before and after the thermal stress, not only the mitigation of electronic traps as fabricated but also the dramatic relaxation of traps during the postannealing step is observed with the LiF incorporation. From this work, LiF has shown its potential as a promising ionic passivator, and the phenomenal achievement of device stability by LiF provides a clear insight to overcome the stability issues of PSCs, a key to the commercialization of next-generation photovoltaics.

CuCrO2 Nanoparticles Incorporated into PTAA as a Hole Transport Layer for 85 °C and Light Stabilities in Perovskite Solar Cells.

High-mobility inorganic CuCrO2 nanoparticles are co-utilized with conventional poly(bis(4-phenyl)(2,5,6-trimethylphenyl)amine) (PTAA) as a hole transport layer (HTL) for perovskite solar cells to improve device performance and long-term stability. Even though CuCrO2 nanoparticles can be readily synthesized by hydrothermal reaction, it is difficult to form a uniform HTL with CuCrO2 alone due to the severe agglomeration of nanoparticles. Herein, both CuCrO2 nanoparticles and PTAA are sequentially deposited on perovskite by a simple spin-coating process, forming uniform HTL with excellent coverage. Due to the presence of high-mobility CuCrO2 nanoparticles, CuCrO2/PTAA HTL demonstrates better carrier extraction and transport. A reduction in trap density is also observed by trap-filled limited voltages and capacitance analyses. Incorporation of stable CuCrO2 also contributes to the improved device stability under heat and light. Encapsulated perovskite solar cells with CuCrO2/PTAA HTL retain their efficiency over 90% after ~900-h storage in 85 °C/85% relative humidity and under continuous 1-sun illumination at maximum-power point.

Interfacial Modification and Defect Passivation by the Cross-Linking Interlayer for Efficient and Stable CuSCN-Based Perovskite Solar Cells.

The study of the inorganic hole-transport layer (HTL) in perovskite solar cells (PSCs) is gathering attention because of the drawback of the conventional PSC design, where the organic HTL with salt dopants majorly participates in the degradation mechanisms. On the other hand, inorganic HTL secures better stability, while it offers difficulties in the deposition and interfacial control to realize high-performing devices. In this study, we demonstrate polydimethylsiloxane (PDMS) as an ideal polymeric interlayer which prevents interfacial degradation and improves both photovoltaic performance and stability of CuSCN-based PSC by its cross-linking behavior. Surprisingly, the PDMS polymers are identified to form chemical bonds with perovskite and CuSCN, as shown by Raman spectroscopy. This novel cross-linking interlayer of PDMS enhances the hole-transporting property at the interface and passivates the interfacial defects, realizing the PSC with high power-conversion efficiency over 19%. Furthermore, the utilization of the PDMS interlayer greatly improves the stability of solar cells against both humidity and heat by mitigating the interfacial defects and interdiffusion. The PDMS-interlayered PSCs retained over 90% of the initial efficiencies, both after 1000 h under ambient conditions (unencapsulated) and after 500 h under 85 °C/85% relative humidity (encapsulated).

Efficient Type-II Heterojunction Nanorod Sensitized Solar Cells Realized by Controlled Synthesis of Core/Patchy-Shell Structure and CdS Cosensitization.

Here, we report the successful application of core/patchy-shell CdSe/CdSe xTe1- x type-II heterojunction nanorods (HNRs) to realize efficient sensitized solar cells. The core/patchy-shell structure designed to have a large type-II heterointerface without completely shielding the CdSe core significantly improves photovoltaic performance compared to other HNRs with minimal or full-coverage shells. In addition, cosensitization with CdS grown by successive ionic layer adsorption and reaction further improves the power conversion efficiency. One-diode model analysis reveals that the HNRs having exposed CdSe cores and suitably grown CdS result in significant reduction of series resistance. Investigation of the intercorrelation between diode quality parameters, diode saturation current density ( J0) and recombination order (ß = (ideality factor)-1) reveals that HNRs with open CdSe cores exhibit reduced recombination. These results confirm that the superior performance of core/patchy-shell HNRs results from their fine-tuned structure: photocurrent is increased by the large type-II heterointerface and recombination is effectively suppressed due to the open CdSe core enabling facile electron extraction. An optimized power conversion efficiency of 5.47% (5.89% with modified electrode configuration) is reported, which is unmatched among photovoltaics utilizing anisotropic colloidal heterostructures as light-harvesting materials.

Microstructural Evolution of Hybrid Perovskites Promoted by Chlorine and its Impact on the Performance of Solar Cell.

The role of Cl in halide hybrid perovskites CH3NH3PbI3(Cl) (MAPbI3(Cl)) on the augmentation of grain size is still unclear although many reports have referred to these phenomena. Herein, we synthesized MAPbI3(Cl) perovskite films by using excess MACl-containing precursors, which exhibited approximately an order of magnitude larger grain size with higher <110>-preferred orientation compared with that from stoichiometric precursors. Comprehensive mechanisms for the large grain evolution by Cl incorporation were elucidated in detail by correlating the changes in grain orientation, distribution of grain size, and the remaining Cl in the perovskite during thermal annealing. In the presence of Cl, <110>- and <001>-oriented grains grew faster than other grains at the initial stage of annealing. Further annealing led to the dissipation of Cl, resulting in the shrinkage of <001> grains while <110> grains continuously grew, as analyzed by x-ray rocking curve and diffraction. As a result of reduced grain boundaries and enhanced <110> texture, the trap density of perovskite solar cells diminished by ~10% by incorporating MACl in the precursor, resulting in a fill factor more than 80%.

Electronic Traps and Their Correlations to Perovskite Solar Cell Performance via Compositional and Thermal Annealing Controls.

Herein, underlying factors for enabling efficient and stable performance of perovskite solar cells are studied through nanostructural controls of organic-inorganic halide perovskites. Namely, MAPbI3, (FA0.83MA0.17)Pb(I0.83Br0.17)3, and (Cs0.10FA0.75MA0.15)Pb(I0.85Br0.15)3 perovskites (abbreviated as MA, FAMA, and CsFAMA, respectively) are examined with a grain growth control through thermal annealing. FAMA- and CsFAMA-based cells result in stable photovoltaic performance, while MA cells are sensitively dependent on the perovskite grain size dominated by annealing time. Micro-/nanoscopic features are comprehensively analyzed to unravel the origin that is directly correlated to the cell performance with the applications of electronic-trap characterizations such as photoconductive noise microscopy and capacitance analyses. It is revealed that CsFAMA has a lower trap density compared to MA and FAMA through the analyses of 1/ f noises and trapping/detrapping capacitances. Also, an open-circuit voltage ( Voc) change is correlated to the variation of trap states during the shelf-life test: FAMA and CsFAMA cells with the negligible change of Voc over weeks exhibit trap states shifting toward the band edge, although the power-conversion efficiencies are clearly reduced. The origins that critically affect the solar cell performance through the characterizations of shallow/deep traps with additional mobile defects in the perovskite and interfaces are discussed.

Differences in prognosis and efficacy of chemotherapy by p53 expression in triple-negative breast cancer.

PURPOSE: TP53 mutation is the most common mutation in breast cancer, and it is considered a target marker of triple-negative breast cancer (TNBC). We investigated whether expression of p53 detected by immunochemical staining predicts the chemotherapy response of TNBC. METHODS: A total of 11,393 TNBC patients who had between stage I and stage III enrolled in the Korean Breast Cancer Society Registry database from January 1, 2000 to December 31, 2015. There were 6,331 'p53-positive (+) TNBC' patients and 5062 'p53-negative (-) TNBC' patients. RESULTS: In univariate analysis, p53(+) TNBC had a worse prognosis than p53(-) TNBC in patients not receiving chemotherapy (P = 0.003). However, there was no difference in prognosis between p53(+) TNBC and p53(-) TNBC for patients receiving chemotherapy. In multivariate analysis adjusted for age and stage, the risk of p53(+) TNBC was 1.84 times higher than that of p53(-) TNBC in the non-chemotherapy group. However, there was no difference between p53(+) TNBC and p53(-) TNBC in patients receiving chemotherapy. In p53(+) TNBC, the risk was 0.6-fold lower when chemotherapy was administered than when chemotherapy was not administered. However, in p53(-) TNBC, there was no risk reduction effect by chemotherapy. CONCLUSION: The prognosis of p53(+) TNBC has worse than p53(-) TNBC, but the risk for survival was significantly reduced with chemotherapy. It suggests that p53(+) TNBC would be more sensitive to chemotherapy than p53(-) TNBC.

Optimum Morphology of Mixed-Olivine Mesocrystals for a Li-Ion Battery.

In this present work, we report on the synthesis of micron-sized LiMn0.8Fe0.2PO4 (LMFP) mesocrystals via a solvothermal method with varying pH and precursor ratios. The morphologies of resultant LMFP secondary particles are classified into two major classes, flakes and ellipsoids, both of which are featured by the mesocrystalline aggregates where the primary particles constituting LMFP secondary particles are crystallographically aligned. Assessment of the battery performance reveals that the flake-shaped LMFP mesocrystals exhibit a specific capacity and rate capability superior to those of other mesocrystals. The origin of the enhanced electrochemical performance is investigated in terms of primary particle size, pore structure, antisite-defect concentration, and secondary particle shape. It is shown that the shape of the secondary particle has just as much of a significant effect on the battery performance as the crystallite size and antisite defects do. We believe that this work provides a rule of design for electrochemically favorable meso/nanostructures, which is of great potential for improving battery performance by tuning the morphology of particles on multilength scales.

From Nanostructural Evolution to Dynamic Interplay of Constituents: Perspectives for Perovskite Solar Cells.

Moving away from the high-performance achievements in organometal halide perovskite (OHP)-based optoelectronic and photovoltaic devices, intriguing features have been reported in that photocarriers and mobile ionic species within OHPs interact with light, electric fields, or a combination of both, which induces both spatial and temporal changes of optoelectronic properties in OHPs. Since it is revealed that the transport of photocarriers and the migration of ionic species are affected not only by each other but also by the inhomogeneous character, which is a consequence of the route selected to deposit OHPs, understanding the nanostructural evolution during OHP deposition, in terms of the resultant structural defects, electronic traps, and nanoscopic charge behaviors, will be valuable. Investigation of the film-growth mechanisms and strategies adopted to realize OHP films with less-defective large grains is of central importance, considering that single-crystalline OHPs have exhibited the most beneficial properties, including carrier lifetimes. Critical factors governing the behavior of photocarriers, mobile ionic species, and nanoscale optoelectronic properties resulting from either or all of them are further summarized, which may potentially limit or broaden the optoelectronic and photovoltaic applications of OHPs. Through inspection of the recent advances, a comprehensive picture and future perspective of OHPs are provided.

Route to Improving Photovoltaics Based on CdSe/CdSexTe1-x Type-II Heterojunction Nanorods: The Effect of Morphology and Cosensitization on Carrier Recombination and Transport.

One-dimensionally elongated nanoparticles with type-II staggered band offset are of potential use as light-harvesting materials for photovoltaics, but only a limited attention has been given to elucidate the factors governing the cell performance obtainable from such materials. Herein, we describe a combined strategy to enhance charge collection from CdSe/CdSexTe1-x type-II heterojunction nanorods (HNRs) utilized as light harvesters for sensitized solar cells. By integrating morphology- and composition-tuned type-II HNRs into solar cells, factors that yield interfaces favorable both for the electron injection into TiO2 and hole transfer to electrolyte are examined. Furthermore, it is shown that a more efficient photovoltaic system results from cosensitization with CdS quantum dots (QDs) predeposited on a TiO2 scaffold, which improves charge collection from HNRs. Electrochemical impedance spectroscopy (EIS) analysis suggests that such a synergistically enhanced system benefits from the decreased recombination within HNRs and facilitated charge transport through the cosensitized TiO2 electrode, even with the activation of a recombination path presumably related to the photogenerated holes in CdS QDs.

Tailoring the Mesoscopic TiO2 Layer: Concomitant Parameters for Enabling High-Performance Perovskite Solar Cells.

Architectural control over the mesoporous TiO2 film, a common electron-transport layer for organic-inorganic hybrid perovskite solar cells, is conducted by employing sub-micron sized polystyrene beads as sacrificial template. Such tailored TiO2 layer is shown to induce asymmetric enhancement of light absorption notably in the long-wavelength region with red-shifted absorption onset of perovskite, leading to ~20% increase of photocurrent and ~10% increase of power conversion efficiency. This enhancement is likely to be originated from the enlarged CH3NH3PbI3(Cl) grains residing in the sub-micron pores rather than from the effect of reduced perovskite-TiO2 interfacial area, which is supported from optical bandgap change, haze transmission of incident light, and one-diode model parameters correlated with the internal surface area of microporous TiO2 layers. With the templating strategy suggested, the necessity of proper hole-blocking method is discussed to prevent any direct contact of the large perovskite grains infiltrated into the intended pores of TiO2 scaffold, further mitigating the interfacial recombination and leading to ~20% improvement in power conversion efficiency compared with the control device using conventional solution-processed hole blocking TiO2. Thereby, the imperatives that originate from the structural engineering of the electron-transport layer are discussed to understand the governing elements for the improved device performance.

Evaluating the Optoelectronic Quality of Hybrid Perovskites by Conductive Atomic Force Microscopy with Noise Spectroscopy.

Organic-inorganic hybrid perovskite solar cells have emerged as promising candidates for next-generation solar cells. To attain high photovoltaic efficiency, reducing the defects in perovskites is crucial along with a uniform coating of the films. Also, evaluating the quality of synthesized perovskites via facile and adequate methods is important as well. Herein, CH3NH3PbI3 perovskites were synthesized by applying second solvent dripping to nonstoichiometric precursors containing excess CH3NH3I. The resulting perovskite films exhibited a larger average grain size with a better crystallinity compared to that from stoichiometric precursors. As a result, the performance of planar perovskite solar cells was significantly improved, achieving an efficiency of 14.3%. Furthermore, perovskite films were effectively analyzed using a conductive AFM and noise spectroscopy, which have been uncommon in the field of perovskite solar cells. Comparing the topography and photocurrent maps, the variation of photocurrents in nanoscale was systematically investigated, and a linear relationship between the grain size and photocurrent was revealed. Also, noise analyses with a conductive probe enabled examination of the defect density of perovskites at specific grain interiors by excluding the grain-boundary effect, and reduced defects were clearly observed for the perovskites using CH3NH3I-rich precursors.

Solvent and Intermediate Phase as Boosters for the Perovskite Transformation and Solar Cell Performance.

High power conversion efficiency and device stabilization are two major challenges for CH3NH3PbI3 (MAPbI3) perovskite solar cells to be commercialized. Herein, we demonstrate a diffusion-engineered perovskite synthesis method using MAI/ethanol dipping, and compared it to the conventional synthesis method from MAI/iso-propanol. Diffusion of MAI/C2H5OH into the PbCl2 film was observed to be more favorable than that of MAI/C3H7OH. Facile perovskite conversion from ethanol and highly-crystalline MAPbI3 with minimized impurities boosted the efficiency from 5.86% to 9.51%. Additionally, we further identified the intermediates and thereby the reaction mechanisms of PbCl2 converting into MAPbI3. Through straightforward engineering to enhance the surface morphology as well as the crystallinity of the perovskite with even faster conversion, an initial power conversion efficiency of 11.23% was obtained, in addition to superior stability after 30 days under an ambient condition.

Integration of CdSe/CdSexTe1-x Type-II Heterojunction Nanorods into Hierarchically Porous TiO2 Electrode for Efficient Solar Energy Conversion.

Semiconductor sensitized solar cells, a promising candidate for next-generation photovoltaics, have seen notable progress using 0-D quantum dots as light harvesting materials. Integration of higher-dimensional nanostructures and their multi-composition variants into sensitized solar cells is, however, still not fully investigated despite their unique features potentially beneficial for improving performance. Herein, CdSe/CdSe(x)Te(1-x) type-II heterojunction nanorods are utilized as novel light harvesters for sensitized solar cells for the first time. The CdSe/CdSe(x)Te(1-x) heterojunction-nanorod sensitized solar cell exhibits ~33% improvement in the power conversion efficiency compared to its single-component counterpart, resulting from superior optoelectronic properties of the type-II heterostructure and 1-octanethiol ligands aiding facile electron extraction at the heterojunction nanorod-TiO(2) interface. Additional ~31% enhancement in power conversion efficiency is achieved by introducing percolation channels of large pores in the mesoporous TiO(2) electrode, which allow 1-D sensitizers to infiltrate the entire depth of electrode. These strategies combined together lead to 3.02% power conversion efficiency, which is one of the highest values among sensitized solar cells utilizing 1-D nanostructures as sensitizer materials.

Reduced graphene oxide/carbon double-coated 3-D porous ZnO aggregates as high-performance Li-ion anode materials.

The reduced graphene oxide (RGO)/carbon double-coated 3-D porous ZnO aggregates (RGO/C/ZnO) have been successfully synthesized as anode materials for Li-ion batteries with excellent cyclability and rate capability. The mesoporous ZnO aggregates prepared by a simple solvothermal method are sequentially modified through distinct carbon-based double coating. These novel architectures take unique advantages of mesopores acting as space to accommodate volume expansion during cycling, while the conformal carbon layer on each nanoparticle buffering volume changes, and conductive RGO sheets connect the aggregates to each other. Consequently, the RGO/C/ZnO exhibits superior electrochemical performance, including remarkably prolonged cycle life and excellent rate capability. Such improved performance of RGO/C/ZnO may be attributed to synergistic effects of both the 3-D porous nanostructures and RGO/C double coating.

Improving scattering layer through mixture of nanoporous spheres and nanoparticles in ZnO-based dye-sensitized solar cells.

A scattering layer is utilized by mixing nanoporous spheres and nanoparticles in ZnO-based dye-sensitized solar cells. Hundred-nanometer-sized ZnO spheres consisting of approximately 35-nm-sized nanoparticles provide not only effective light scattering but also a large surface area. Furthermore, ZnO nanoparticles are added to the scattering layer to facilitate charge transport and increase the surface area as filling up large voids. The mixed scattering layer of nanoparticles and nanoporous spheres on top of the nanoparticle-based electrode (bilayer geometry) improves solar cell efficiency by enhancing both the short-circuit current (J sc) and fill factor (FF), compared to the layer consisting of only nanoparticles or nanoporous spheres.