Temporal Patterns of Angular Displacement of Endosomes: Insights into Motor Protein Exchange Dynamics.

The material transport system, facilitated by motor proteins, plays a vital role in maintaining a non-equilibrium cellular state. However, understanding the temporal coordination of motor protein activity requires an advanced imaging technique capable of measuring 3D angular displacement in real-time. In this study, a Fourier transform-based plasmonic dark-field microscope has been developed using anisotropic nanoparticles, enabling the prolonged and simultaneous observation of endosomal lateral and rotational motion. A sequence of discontinuous 3D angular displacements has been observed during the pause and run phases of transport. Notably, a serially correlated temporal pattern in the intermittent rotational events has been demonstrated during the tug-of-war mechanism, indicating Markovian switching between the exploitational and explorational modes of motor protein exchange prior to resuming movement. Alterations in transition frequency and the exploitation-to-exploration ratio upon dynein inhibitor treatment highlight the relationship between disrupted motor coordination and reduced endosomal transport efficiency. Collectively, these results suggest the importance of orchestrated temporal motor protein patterns for efficient cellular transport.

Determination of 57 pesticide residues in fishery products by GC tandem mass spectrometry combined with QuEChERS (quick, easy, cheap, effective, rugged, and safe) extraction.

An analytical method using GC-MS/MS combined with quick, easy, cheap, effective, rugged, and safe extraction was developed to determine 57 pesticides in fishery products. The limits of detection and quantification (LOD and LOQ, respectively) of the analytical method ranged between 0.91 and 2.12 ng/g wet mass and 3 and 7 ng/g wet mass, respectively. Moreover, the linearity of the calibration curves was acceptable (R2 > 0.99). The relative pesticide recoveries ranged between 53.87 and 127.2%, and reproducibility ranged between 0.25 and 10.87%. The pesticide residues in brown seaweed, eel, flatfish, shrimp, and abalone samples were analyzed using the developed analytical method, and the results indicate that most samples were not contaminated by the 57 target pesticides, except low levels (< 10 ng/g) of 1,1-dichloro-2,2-bis(4-chlorophenyl)ethene, alachlor, ametryn, isoprothiolane, and prometryn in several samples.

Effect of rice milling, washing, and cooking on reducing pesticide residues.

The effects of milling, washing, and cooking on etofenprox, flubendiamide, and tebufenozide levels in brown and polished rice were investigated by HPLC using a UV detector. The reduction rates of etofenprox, flubendiamide, and tebufenozide after milling were 68.74-93.16%, 64.49-90.25%, and 69.74-92.58%, respectively, 11.64-41.44%, 31.36-65.37%, and 31.61-73.79%, respectively, after washing brown rice, and 30.85-82.08%, 52.13-83.05%, and 43.04-83.89%, respectively, after washing polished rice. The residue levels of the three pesticides in brown rice decreased after electric and pressure cooking by 56.49 and 54.41%, 75.80 and 73.42%, and 70.01 and 71.27%, respectively, and the corresponding levels in polished rice decreased after electric and pressure cooking by 85.58 and 85.82%, 86.70 and 87.06%, and 89.89 and 89.68%, respectively. In conclusion, various processing methods decrease the residual levels of etofenprox, flubendiamide, and tebufenozide in rice.

From Homogeneity to Turing Pattern: Kinetically Controlled Self-Organization of Transmembrane Protein.

Understanding the spatial organization of membrane proteins is crucial for unraveling key principles in cell biology. The reaction-diffusion model is commonly used to understand biochemical patterning; however, applying reaction-diffusion models to subcellular phenomena is challenging because of the difficulty in measuring protein diffusivity and interaction kinetics in the living cell. In this work, we investigated the self-organization of the plasmalemma vesicle-associated protein (PLVAP), which creates regular arrangements of fenestrated ultrastructures, using single-molecule tracking. We demonstrated that the spatial organization of the ultrastructures is associated with a decrease in the association rate by actin destabilization. We also constructed a reaction-diffusion model that accurately generates a hexagonal array with the same 130 nm spacing as the actual scale and informs the stoichiometry of the ultrastructure, which can be discerned only through electron microscopy. Through this study, we integrated single-molecule experiments and reaction-diffusion modeling to surpass the limitations of static imaging tools and proposed emergent properties of the PLVAP ultrastructure.

Real-time monitoring unsafe behaviors of portable multi-position ladder worker using deep learning based on vision data.

INTRODUCTION: Fatal fall from height accidents, especially on construction sites, persist, underscoring the importance of monitoring and managing worker behaviors to enhance safety. Deep learning showed the possibility of substituting the manual work of safety managers. However, applying detection results to determine compliance with safety regulations has limitations. METHOD: This study estimated the actual working height depending on the height of the object detection bounding box by specifying the consistent hinge part as a target marker based on ladder manufacturing regulations. Furthermore, an attempt was made to improve the separation between workers, coworkers, and persons unconnected to ladder activities by applying an optimized loss function alongside an attention mechanism. RESULTS: The experimental results showed that an average precision increased from 87.60% to 90.44%. The performance of the monitoring unsafe behavior of ladder worker following the Korea Occupational Safety and Health Agency (KOSHA) guide was evaluated by 91.40 F1-Score, which accumulated sorted according to the working height. CONCLUSIONS: Experimental results show the feasibility of the real-time automate safety monitoring in ladder work. PRACTICAL APPLICATIONS: By linking the estimated working height and deep learning multi-detection results to established safety regulations, the proposed method shows the potential to automatically monitoring unsafe behaviors in construction site.

Development of Photo-Polymerization-Type 3D Printer for High-Viscosity Ceramic Resin Using CNN-Based Surface Defect Detection.

Due to the high hardness and brittleness of ceramic materials, conventional cutting methods result in poor quality and machining difficulties. Additive manufacturing has also been tried in various ways, but it has many limitations. This study aims to propose a system to monitor surface defects that occur during the printing process based on high-viscosity composite resin that maximizes ceramic powder content in real time using image processing and convolutional neural network (CNN) algorithms. To do so, defects mainly observed on the surface were classified into four types by form: pore, minor, critical, and error, and the effect of each defect on the printed structure was tested. In order to improve the classification efficiency and accuracy of normal and defective states, preprocessing of images obtained based on cropping, dimensionality reduction, and RGB pixel standardization was performed. After training and testing the preprocessed images based on the DenseNet algorithm, a high classification accuracy of 98% was obtained. Additionally, for pore and minor defects, experiments confirmed that the defect surfaces can be improved through the reblading process. Therefore, this study presented a defect detection system as well as a feedback system for process modifications based on classified defects.

Fabrication of 3D Printed Ceramic Part Using Photo-Polymerization Process.

Ceramics are high-strength and high-temperature resistant materials that are used in various functional parts. However, due to the high strength and brittleness properties, there are many difficulties in the fabrication of complex shapes. Therefore, there are many studies related to the fabrication of ceramic parts using 3D printing technology optimized for complex shapes. Among them, studies using photo-polymerization (PP) 3D printing technology with excellent dimensional accuracy and surface quality have received the most widespread attention. To secure the physical properties of sintered ceramic, the content and distribution of materials are important. This study suggests a novel 3D printing process based on a high-viscosity composite resin that maximizes the content of zirconia ceramics. For reliable printing, the developed 3D printers that can adjust the process environment were used. To minimize warpage and delamination, the divided micro square pattern images were irradiated in two separate intervals of 1.6 s each while maintaining the internal chamber temperature at 40 °C. This contributed to improved stability and density of the sintered structures. Ultimately, the ceramic parts with a Vickers hardness of 12.2 GPa and a relative density of over 95% were able to be fabricated based on a high-viscosity resin with 25,000 cps.

Intra- and Interrater Agreement of Face Esthetic Analysis in 3D Face Images.

The use of three-dimensional (3D) facial scans for facial analysis is increasing in maxillofacial treatment. The aim of this study was to investigate the consistency of two-dimensional (2D) and 3D facial analyses performed by multiple raters. Six men and four women (25-36-year-old) participated in this study. The 2D images of the smiling and resting faces in the frontal and sagittal planes were obtained. The 3D facial and intraoral scans were merged to generate virtual 3D faces. Ten clinicians performed facial analyses by investigating 14 indices of 2D and 3D faces. Intra- and interrater agreements of the results of 2D and 3D facial analyses within and among the participants were evaluated. The intrarater agreement between the 2D and 3D facial analyses varied according to the indices. The highest and lowest agreements were found for the dental crowding index (0.94) and smile line curvature index (0.56) in the frontal plane, and Angle's classification (canine) index (0.98) and occlusal plane angle index (0.55) in the profile plane. In the frontal plane, the interrater agreements were generally higher for the 3D images than for the 2D images, while in the profile plane, the interrater agreements were high in the Angle's classification (canine) index however low in the other indices. Several occlusion-related indices were missing in the 2D images because the posterior teeth were not observed. Esthetic analysis results between 2D and 3D face images can differ according to the evaluation indices. The use of 3D faces is recommended over 2D images to increase the reliability of facial analyses, as it can fully assess both esthetic and occlusion-related indices.

Highly Reliable Ovonic Threshold Switch with TiN/GeTe/TiN Structure.

A new architecture has become necessary owing to the power consumption and latency problems of the von Neumann architecture. A neuromorphic memory system is a promising candidate for the new system as it has the potential to process large amounts of digital information. A crossbar array (CA), which consists of a selector and a resistor, is the basic building block for the new system. Despite the excellent prospects of crossbar arrays, the biggest obstacle for them is sneak current, which can cause a misreading between the adjacent memory cells, thus resulting in a misoperation in the arrays. The chalcogenide-based ovonic threshold switch (OTS) is a powerful selector with highly nonlinear I-V characteristics that can be used to address the sneak current problem. In this study, we evaluated the electrical characteristics of an OTS with a TiN/GeTe/TiN structure. This device shows nonlinear DC I-V characteristics, an excellent endurance of up to 109 in the burst read measurement, and a stable threshold voltage below 15 mV/dec. In addition, at temperatures below 300 °C, the device exhibits good thermal stability and retains an amorphous structure, which is a strong indication of the aforementioned electrical characteristics.

Effect of Al Concentration on Basal Texture Formation Behavior of AZ-Series Magnesium Alloys during High-Temperature Deformation.

Magnesium and its alloys have been restricted in their industrial applications due to problems related to their formability. To overcome this issue, controlling the crystallographic texture is important, and the texture formation mechanism should be investigated in relation to factors including deformation conditions and solute atoms. In particular, the effects of solute atoms on the texture formation behavior should be further analyzed because they can considerably affect the deformation behavior. Thus, in this study, to clarify the effect of aluminum concentration on the texture formation behavior and microstructure, high-temperature uniaxial compression tests were conducted on three types of AZ-series magnesium alloys (AZ31, AZ61, and AZ91). Compression was conducted at 673 K and 723 K, with strain rates of 0.05 s-1 and 0.005 s-1, up to a true strain of -1.0. Cylindrical specimens were prepared from a rolled plate that had a (0001) basal texture and was compressed parallel to the c-axis of the grains. Consequently, work softening and fiber texture formation were observed in all the specimens. During the deformation, the development of grain boundaries, which is a typical characteristic of continuous dynamic recrystallization (CDRX), was observed, and the (0001) texture was highly developed with increasing Al content. Although each alloy was associated with the same deformation conditions and mechanisms, the AZ31 alloy exhibited a non-basal texture component. The stacking fault energy contributed to the generation of slip systems and gliding, and it was seen as the main reason for texture variation.

Effect of Recrystallization Behavior of AZ31 Magnesium Alloy on Damping Capacity.

For a wide industrial application of magnesium alloys, a method for imparting high damping properties while maintaining mechanical properties is required. Controlling the crystallographic texture seems to be useful, because dislocations are known to have a significant influence on the damping characteristics of magnesium alloys. In addition, textures are affected by the microstructure and texture variation when the deformation or annealing is applied. However, there were less reports about their effect on damping capacity. Therefore, the effect of twinning and annealing, which can affect the recrystallization, were investigated in this study. An AZ31 alloy was hot rolled at 673 K with a reduction ratio of 10% and 50%, and then annealed at 673 K and 723 K for 0.5, 1, 2, and 3 h, respectively. SEM-EBSD was used to examine the microstructure and texture. In addition, each specimen's hardness and internal friction were contemporarily measured. As a result, hot rolling produced tensile twins and their fraction increased with internal friction when the reduction ratio increased. Due to annealing, a discontinuous type of static recrystallization occurred within the twinning grains, and was highly activated along with the increasing annealing temperature and the fraction of twinning. In the samples annealed at 723 K, the internal friction continuously increased over the annealing time, whereas in the samples annealed at 673 K, the decrease in dislocation density was delayed while the internal friction showed a relatively low value.

Two GPSes in a Ball: Deciphering the Endosomal Tug-of-War Using Plasmonic Dark-Field STORM.

Live video recording of intracellular material transport is a promising means of deciphering the fascinating underlying mechanisms driving life at the molecular level. Such technology holds the key to realizing real-time observation at appropriate resolutions in three-dimensional (3D) space within living cells. Here, we report an optical microscopic method for probing endosomal dynamics with proper spatiotemporal resolution within 3D space in live cells: plasmonic dark-field STORM (pdf-STORM). We first confirmed that pdf-STORM has a spatial resolution comparable to that of scanning electron microscopy. Additionally, by observing two optical probes within a single organelle, we were able to track rotational movements and demonstrate the feasibility of using pdf-STORM to observe the angular displacements of an endosome during a "tug-of-war" over an extended period. Finally, we show various biophysical parameters of the hitherto unelucidated dynamics of endosomes-angular displacement is discontinuous and y-axis movement predominates and follows a long-tail distribution.

Reduction in residual cyantraniliprole levels in spinach after various washing and blanching methods.

Pesticides are used to protect crops from pests and diseases. However, as many pesticides are toxic to humans, it is necessary to assess methods that can remove pesticide residues from agricultural products before human consumption. Spinach is consumed immediately after a relatively simple washing and heating process in the Republic of Korea. Cyantraniliprole is used as a systemic insecticide during spinach cultivation, which means it might remain in the crop after processing. Consequently, it is important to assess whether residues can be reduced to levels that are harmless to the human body after processing. This study investigated lowering the residual cyantraniliprole levels in spinach after washing and blanching. The amount of cyantraniliprole residue in the spinach samples sprayed with cyantraniliprole during cultivation was analyzed using ultrahigh-performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). The time of each washing and blanching method was set at 1, 3, and 5 min. The residual levels of cyantraniliprole decreased by 15.1-54.6% and 60.1-93.5% based on the washing and blanching methods employed. The most effective washing method to lower residual cyantraniliprole levels was steeping with a neutral detergent, resulting in cyantraniliprole reduction by 42.9-54.6%. When spinach was blanched after steeping washing with a neutral detergent, the largest removal rates of 77.9 and 91.2% were observed after 1 and 3 min of blanching, respectively. Blanching for 5 min after steeping and running washing exhibited the highest reduction rate of 93.5%. Therefore, a considerable amount of cyantraniliprole residue in spinach could be removed by washing or blanching. Based on the results of this study, blanching after steeping washing can be implemented as an effective method of lowering pesticide concentrations in spinach and other crops, thereby reducing their potential toxicity to humans upon consumption.

Quad-Level Cell Switching with Excellent Reliability in TiN/AlOx:Ti/TaOx/TiN Memory Device.

TiN/AlOx:Ti/TaOx/TiN memory devices using bilayer resistive switching memory demonstrated excellent durability and capability of QLC (quad-level cell) memory devices. The best nonvolatile memory characteristics with the lowest operation current and optimized 4 bit/cell states were obtained using the Incremental Step Pulse Programming (ISPP) algorithm in array. As a result, a superior QLC reliability (cycle endurance > 1 k at each level of the QLC, data retention > 2 h at 125 °C) for all the 4 bits/cell operations was achieved in sub-µm scaled RRAM (resistive random access memory) devices.

Sunlight-Activatable ROS Generator for Cell Death Using TiO2/c-Si Microwires.

Solar-driven reactive oxygen species (ROS) generation is an attractive disinfection technique for cell death and water purification. However, most photocatalysts require high stability in the water environment and the production of ROS with a sufficient amount and diffusion length to damage pathogens. Here, a ROS generation system was developed consisting of tapered crystalline silicon microwires coated with anatase titanium dioxide for a conformal junction. The system effectively absorbed >95% of sunlight over 300-1100 nm, resulting in effective ROS generation. The system was designed to produce various ROS species, but a logistic regression analysis with cellular survival data revealed that the diffusion length of the ROS is ∼9 µm, implying that the most dominant species causing cell damage is H2O2. Surprisingly, a quantitative analysis showed that only 15 min of light irradiation on the system would catalyze a local bactericidal effect comparable to the conventional germicidal level of H2O2 (∼3 mM).

Designing of reverse vending machine to improve its sorting efficiency for recyclable materials for its application in convenience stores.

Plastics have multiple applications in disposable products, high-end technology parts, etc., owing to their functionality and manufacturing flexibility. However, their increased use has increased the global proportion of plastic wastes, which creates a serious environmental issue, thereby, creating a demand for plastic waste management techniques. Improving the efficiency of resource recovery by appropriate sorting and collection systems is necessary for successful plastic recycling. Therefore, this study proposed a three-step optimization process of a reverse vending machine (RVM), a small automatic recyclable waste sorter/collector system, for acquiring an optimal design and enhanced efficiency. The RVM system categorized recyclable wastes as plastics, glass, and cans using barcode, vision, and near infrared sensors. The average sorting efficiency of the designed RVM system was 94%, 95% for polyethylene terephthalate, and 98% for glass bottles. Therefore, the RVM system, with the average sorting efficiency of 95%, is suitable for application in on-site sorting in small-sized areas, such as convenience stores, which generate wastes on a small scale.Implications: This study proposed a three-step optimization process of a reverse vending machine (RVM), a small automatic recyclable waste sorter/collector system, for acquiring an optimal design and enhanced efficiency. The RVM system is suitable for application in on-site sorting in small-sized areas, such as convenience stores, which generate wastes on a small scale.

USP14 Inhibition Regulates Tumorigenesis by Inducing Autophagy in Lung Cancer In Vitro.

The ubiquitin-proteasome system is an essential regulator of several cellular pathways involving oncogenes. Deubiquitination negatively regulates target proteins or substrates linked to both hereditary and sporadic forms of cancer. The deubiquitinating enzyme ubiquitin-specific protease 14 (USP14) is associated with proteasomes where it trims the ubiquitin chain on the substrate. Here, we found that USP14 is highly expressed in patients with lung cancer. We also demonstrated that USP14 inhibitors (IU1-47 and siRNA-USP14) significantly decreased cell proliferation, migration, and invasion in lung cancer. Remarkably, we found that USP14 negatively regulates lung tumorigenesis not only through apoptosis but also through the autophagy pathway. Our findings suggest that USP14 plays a crucial role in lung tumorigenesis and that USP14 inhibitors are potent drugs in lung cancer treatment.

Functional and structural evaluation of the meibomian gland using a LipiView interferometer in thyroid eye disease.

OBJECTIVE: The purpose of this study was to evaluate the structure and function of the meibomian gland and the incomplete blinking rate to understand the pathophysiology of dry eye in thyroid eye disease (TED) patients. METHODS: Patients who were diagnosed with TED were enrolled between October 2015 and February 2016. Clinical measurements were performed in the following order: (i) external examination (Hertel exophthalmometer and palpebral fissure height), (ii) LipiView interferometer (lipid layer thickness [LLT], incomplete blinking rate, and meibography), (iii) slit-lamp biomicroscopy (corneal surface staining, tear breakup time, meibum expression, Marx line). RESULTS: Thirty eyes of 30 TED patients (male = 8; female = 22) were included in this study. The TED patient population had a mean age of 42.9 ± 11.8 years and a mean clinical activity score (CAS) of 2.33 ± 1.60. The meiboscore was 1.17 ± 0.90 in the upper eyelid and 0.70 ± 0.65 in the lower eyelid; scores were significantly higher in the upper eyelid (p < 0.001). The mean LLT was 82.43 ± 24.52 nm, and the mean incomplete blinking rate was 51.04 ± 33.62% (0-100%). CAS was the only variable that correlated with the meiboscore. There was no significant correlation between incomplete blinking and a degree of palpebral fissure height or proptosis. CONCLUSIONS: Tear film instability due to increased incomplete blinking can cause dry eye in TED. In addition to the increase in CAS, meibomian gland dysfunction may also be a cause of dry eye in TED. However, further comparative studies are needed to confirm these results.

The impact of a quality improvement effort in reducing admission hypothermia in preterm infants following delivery.

PURPOSE: Hypothermia at admission is associated with increased mortality and morbidity in preterm infants. We performed a quality improvement (QI) effort to determine the impact of a decrease in admission hypothermia in preterm infants. METHODS: The study enrolled very low birth weight (VLBW) infants born at Gangnam Severance Hospital between January 2013 and December 2016. This multidisciplinary QI effort included the use of occlusive wraps, warm blankets, and caps; the delivery room temperature was maintained above 23.0˚C, and a check-list was used for feedback. RESULTS: Among 259 preterm infants, the incidence of hypothermia (defined as body temperature <36.0˚C) decreased significantly from 68% to 41%, and the mean body temperature on neonatal intensive care unit admission increased significantly from 35.5˚C to 36.0˚C. In subgroup analysis of VLBW infants, admission hypothermia and neonatal outcomes were compared between the pre-QI (n=55) and post-QI groups (n=75). Body temperature on admission increased significantly from 35.4˚C to 35.9˚C and the number of infants with hypothermia decreased significantly from 71% to 45%. There were no cases of neonatal hyperthermia. The incidence of pulmonary hemorrhage was significantly decreased (P=0.017). Interaction analysis showed that birth weight and gestational age were not correlated with hypothermia following implementation of the protocol. CONCLUSION: Our study demonstrated a significant reduction in admission hypothermia following the introduction of a standardized protocol in our QI effort. This resulted in an effective reduction in the incidence of massive pulmonary hemorrhage.

Prediction of Postnatal Growth Failure among Very Low Birth Weight Infants.

Postnatal growth failure (PGF) in preterm infants remains an important clinical issue. In this study, we analysed the incidence of PGF among very low birth weight (VLBW) infants and evaluated the risk factors for PGF based on the data of 2799 VLBW infants obtained from the Korean Neonatal Network database from 2013 to 2014. PGF was defined as a decrease in weight Z score between birth and discharge of more than -1.28 using the Fenton growth charts. Risk factors were evaluated in relation to birth weight for gestational age, namely small (SGA) or appropriate (AGA) for gestational age, using propensity score matching used for between-group differences. The overall incidence of PGF was 45.5%, with a rate of 68.9% in the SGA group and 36.2% in the AGA group. PGF was negatively correlated with gestation and birth weight; additionally, PGF was associated with a higher incidence of co-morbidities. Predictors of PGF in the SGA group were respiratory distress syndrome and days to attain 100 mL/kg of enteral feeding. The only predictor of PGF in the AGA group was days to attain 100 mL/kg of enteral feeding. Early initiation and aggressive progression of enteral nutrition may decrease the incidence of PGF.