Influence of root shape on canal complexity at the mandibular molar apical surgical resection level: A micro-CT study.

OBJECTIVES: This study aimed to investigate the relationship between the aspect ratios of mandibular molar roots at the apical 3-mm level and their root canal complexity. DESIGN: This study used micro-CT imaging to analyze 163 two-rooted mandibular molars. The aspect ratios of the roots at the apical 3-mm level were categorized as "< 2.75" or "≥ 2.75" (mesial) and "< 1.75" or "≥ 1.75" (distal). A two-dimensional (2D) analysis focused on four apical axial cross-section levels to determine the presence of main and accessory canals and isthmus. Additionally, a three-dimensional (3D) assessment of the apical 4-mm of both roots examined main and accessory canals, apical foramina, apical deltas, and middle mesial canals. RESULTS: Mesial roots with aspect ratios ≥ 2.75 showed a higher number of main canals at all levels compared to those with aspect ratios < 2.75 at the 3-mm level. Additionally, the ≥ 2.75 group exhibited more accessory canals and a higher average number of accessory canals. The 3D assessment confirmed significantly more accessory canals and apical foramina in the ≥ 2.75 group. The prevalence of roots with apical deltas was nearly double in the ≥ 2.75 group, and middle mesial canals were exclusively found in this group. In the distal root, the ≥ 1.75 group showed a significantly higher number of main canals at all axial levels. No significant differences were observed between groups in terms of accessory canals, apical foramina, or deltas. CONCLUSIONS: A higher root aspect ratio is related to higher anatomical complexity.

Diagnostic value of cone beam computed tomography for root canal morphology assessment - a micro-CT based comparison.

OBJECTIVES: The aim of this study was to assess cone beam computed tomography (CBCT) as a root canal anatomy diagnostic tool by comparison with micro-CT gold-standard. MATERIALS AND METHODS: 216 two-rooted mandibular molars were first scanned in a CBCT device (200 µm voxel size) and posteriorly in a micro-CT scanner (19.61 µm). The volumes were sequentially screened to classify main root canal anatomy according to Vertucci classification, and for the presence of lateral canals and apical deltas, in both mesial and distal roots. RESULTS: Both methods revealed a higher prevalence of Vertucci Type II and IV in the mesial root, and Vertucci Type I in the distal root. The percentage of agreement for main root canal anatomy classification between CBCT and micro-CT scores was high (85.2%). CONCLUSION: Sensibility to detect both lateral canals and apical deltas with CBCT was low. These results attest to the fact that minor anatomical changes might be difficult to identify with CBCT imaging, hampering its diagnostic value.

Multimethod analysis of large- and low-tapered single file reciprocating instruments: Design, metallurgy, mechanical performance, and irrigation flow.

AIM: To compare eight large- and low-tapered heat-treated reciprocating instruments regarding their design, metallurgy, mechanical properties, and irrigation flow through an in silico model. METHODOLOGY: A total of 472 new 25-mm E-Flex Rex (25/.04 and 25/.06), Excalibur (25/.05), Procodile (25/.06), Reciproc Blue R25 (25/.08v), WaveOne Gold Primary (25/.07v), and Univy Sense (25/.04 and 25/.06) instruments were evaluated regarding their design (stereomicroscopy, scanning electron microscopy, and 3D surface scanning), metallurgy (energy-dispersive X-ray spectroscopy and differential scanning calorimetry), and mechanical performance (cyclic fatigue, torsional resistance, cutting ability, bending and buckling resistance). Computational fluid dynamics assessment was also conducted to determine the irrigation flow pattern, apical pressure, and wall shear stress in simulated canal preparations. Kruskal-Wallis and one-way anova post hoc Tukey tests were used for statistical comparisons (α = 5%). RESULTS: Instruments presented variations in blade numbers, helical angles, and tip designs, with all featuring non-active tips, symmetrical blades, and equiatomic nickel-titanium ratios. Cross-sectional designs exhibited an S-shaped geometry, except for WaveOne Gold. Univy 25/.04 and Reciproc Blue displayed the smallest and largest core diameters at D3. Univy 25/.04 and E-Flex Rec 25/.04 demonstrated the longest time to fracture (p < .05). Reciproc Blue and Univy 25/.04 exhibited the highest and lowest torque to fracture, respectively (p < .05). Univy 25/.04 and Reciproc Blue had the highest rotation angles, whilst E-Flex Rec 25/.06 showed the lowest angle (p < .05). The better cutting ability was observed with E-Flex Rec 25/.06, Procodile, Excalibur, and Reciproc Blue (p > .05). Reciproc R25 and E-Flex Rec showed the highest buckling resistance values (p < .05), with WaveOne Gold being the least flexible instrument. The impact of instruments' size and taper on wall shear stress and apical pressure did not follow a distinct pattern, although Univy 25/.04 and E-Flex Rec 25/.06 yielded the highest and lowest values for both parameters, respectively. CONCLUSIONS: Low-tapered reciprocating instruments exhibit increased flexibility, higher time to fracture, and greater angles of rotation, coupled with reduced maximum bending loads and buckling strength compared to large-tapered instruments. Nevertheless, low-tapered systems also exhibit lower maximum torque to fracture and inferior cutting ability, contributing to a narrower apical canal enlargement that may compromise the penetration of irrigants in that region.

Methodology and Experimental Protocol for Studying Learning and Motor Control in Neuromuscular Structures in Pilates.

The benefits of Pilates have been extensively researched for their impact on muscular, psychological, and cardiac health, as well as body composition, among other aspects. This study aims to investigate the influence of the Pilates method on the learning process, motor control, and neuromuscular trunk stabilization, specifically in both experienced and inexperienced practitioners. This semi-randomized controlled trial compares the level of experience among 36 Pilates practitioners in terms of motor control and learning of two Pilates-based skills: standing plank and side crisscross. Data will be collected using various assessment methods, including abdominal wall muscle ultrasound (AWMUS), shear wave elastography (SWE), gaze behavior (GA) assessment, electroencephalography (EEG), and video motion. Significant intra- and inter-individual variations are expected, due to the diverse morphological and psychomotor profiles in the sample. The adoption of both linear and non-linear analyses will provide a comprehensive evaluation of how neuromuscular structures evolve over time and space, offering both quantitative and qualitative insights. Non-linear analysis is expected to reveal higher entropy in the expert group compared to non-experts, signifying greater complexity in their motor control. In terms of stability, experts are likely to exhibit higher Lyapunov exponent values, indicating enhanced stability and coordination, along with lower Hurst exponent values. In elastography, experienced practitioners are expected to display higher transversus abdominis (TrA) muscle elasticity, due to their proficiency. Concerning GA, non-experts are expected to demonstrate more saccades, focus on more Areas of Interest (AOIs), and shorter fixation times, as experts are presumed to have more efficient gaze control. In EEG, we anticipate higher theta wave values in the non-expert group compared to the expert group. These expectations draw from similar studies in elastography and correlated research in eye tracking and EEG. They are consistent with the principles of the Pilates Method and other scientific knowledge in related techniques.

High-performance and self-powered visible light photodetector using multiple coupled synergetic effects.

In this work, we demonstrate, for the first time, that coupling together the pyroelectric effect, the photovoltaic effect and the plasmonic effect is a novel method to significantly enhance the performance of self-powered photodetectors in the visible region. Photodetectors based on tri-layered heterojunction of n-Si/p-SnO/n-ZnO through the inclusion of silver (Ag) nanoparticles (NPs) at the SnO/ZnO interface were fabricated. The photo-response of the device, with excitation from a chopped 650 nm wavelength laser, was carefully investigated, and it was shown that the photodetector performance is enhanced the most with the inclusion of spheroidal Ag NPs with ∼70 nm diameter. The Al/Si/SnO/Ag NPs/ZnO/ITO device exhibited an optimum responsivity, detectivity and sensitivity of 210.2 mA W-1, 5.47 × 109 Jones and 15.0 × 104, respectively, together with a rise and fall time of 2.3 and 51.3 µs, respectively, at a laser power density of 317 mW cm-2 and at a chopper frequency of 10 Hz. The present photodetectors are more than twice as responsive as the current best-performing ZnO-based pyro-phototronic photodetectors and they also exhibit other competitive features, such as detectivity, and fall and rise times. Therefore, by exploiting the plasmonic effect of the Ag NPs together with the pyroelectric effect in a ZnO film, and the photovoltaic effect at a Si/SnO junction, all in a single device, photodetectors were developed with state-of-the-art performance for the visible region.

Syringe irrigation in confluent canals: A sequential computational fluid dynamics assessment.

This study aims to assess the influence of root canal preparation, irrigation needle design and its placement depth in the irrigation flow of confluent canals during syringe irrigation. A mandibular molar presenting two confluent canals in its mesial root was sequentially prepared and scanned by micro-computed tomography after mechanical preparation up to ProTaper Next system sizes X2 (25/.06v), X3 (30/.07v) and X4 (40/.06v). In each of the root canal preparation models, a side-vented and an open-ended needle at 5, 3 and 2 mm from the working length were included, and irrigation flow was assessed by a validated computational fluid dynamics model. The results revealed that the irrigant flowed out of the confluent canals mainly through the canal that did not have the needle. Apical penetration and renewal of the irrigant were most efficiently achieved with the use of a 30G open-ended needle and a 30/.07v preparation.

Patients Age 40 Years and Younger With Multiple Myeloma Have the Same Prognosis as Older Patients: An Analysis of Real-World Patients' Evidence From Latin America.

PURPOSE: Multiple myeloma (MM) is a highly heterogeneous, incurable disease most frequently diagnosed in the elderly. Therefore, data on clinical characteristics and outcomes in the very young population are scarce. PATIENTS AND METHODS: We analyzed clinical characteristics, response to treatment, and survival in 103 patients with newly diagnosed MM age 40 years or younger compared with 256 patients age 41-50 years and 957 patients age 51 years or older. RESULTS: There were no statistical differences in sex, isotype, International Scoring System, renal involvement, hypercalcemia, anemia, dialysis, bony lesions, extramedullary disease, and lactate dehydrogenase (LDH). The most used regimen in young patients was cyclophosphamide, bortezomib, dexamethasone, followed by cyclophosphamide, thalidomide, dexamethasone and bortezomib, thalidomide, dexamethasone. Of the patients age 40 years or younger, only 53% received autologous stem-cell transplant (ASCT) and 71.1% received maintenance. There were no differences in overall survival (OS) in the three patient cohorts. In the multivariate analysis, only high LDH, high cytogenetic risk, and ASCT were statistically associated with survival. CONCLUSION: In conclusion, younger patients with MM in Latin America have similar clinical characteristics, responses, and OS compared with the elderly.

Movement variability in Pilates: a scoping review.

Objective: This scoping review aimed to identify studies that analyzed movement variability in Pilates. Following a systematic approach to mapping evidence on this topic would highlight concepts, theories, sources, and knowledge gaps in this area. Methods: This review used the Preferred Reporting Items for Systematic Reviews and Meta-Analyses extension for Scoping Reviews (PRISMA-ScR) criteria for the selection, reading, and analysis of studies in this area. We searched five literature databases (Web of Science, SCOPUS, library catalog of the Faculty of Sport and Physical Education of the University of Coimbra-EBSCO Discovery Services, MEDLINE, and Google Scholar). Eligible articles contained the word "Pilates," and the human movement variability was analyzed. Any type of study (except reviews) could be eligible and must have been published between 1 January 2002 and 30 November 2022, in Portuguese, Spanish, French, or English. Results: Our search identified five eligible entries. Only one study used the Pilates method in its intervention, pointing to a more significant variability of hip-knee coordination, suggesting more diversified coordination patterns, and maintaining the variability of the angular position of the joint. Conclusion: Very few studies have examined movement variability in Pilates, and only one applied an ecological framework.

Characterization of four heat-treated reciprocating instruments: Design, metallurgy, mechanical performance, and irrigation flow patterns.

AIM: To compare the design, metallurgy, and mechanical properties of four heat-treated reciprocating instruments coupled with the evaluation of the irrigation flow using an in silico model. METHODOLOGY: New EdgeOne Fire Primary, Easy-File Flex Regular 25, WaveOne Gold Primary and Reciproc Blue R25 instruments (n = 124) were initially evaluated regarding their design through stereomicroscopy, scanning electron microscopy and 3D surface scanning. In addition, energy-dispersive X-ray spectroscopy was utilized to determine their elemental composition, and differential scanning calorimetry tests to evaluate their phase transformation temperatures. Their mechanical performance was further assessed through torsional and bending tests. Using scans obtained from a real tooth and the instruments, a computational fluid dynamics assessment was conducted to determine the irrigation flow pattern, apical pressure, and wall shear stress in simulated canal preparation. Mood's median and One-way anova post hoc Tukey tests were used for statistical comparisons (α = 5%). RESULTS: Reciproc Blue exhibited a superior number of blades (n = 8), whereas EdgeOne Fire had the highest overall volume (4.38 mm3 ) and surface area (32.32 mm2 ). At the 3-mm axial level, EdgeOne Fire displayed the lowest core diameter (0.13 mm), while Reciproc Blue had the highest (0.16 mm). All blades were symmetrical, and the tips of the instruments were non-active but differed from each other. The most irregular surfaces were observed in EdgeOne Fire and Easy-File Flex. All instruments were manufactured from nickel-titanium alloys and exhibited distinct phase transformation temperatures. WaveOne Gold and Reciproc Blue demonstrated the highest maximum torque values (1.87 and 1.62 N cm, respectively), while the lowest was observed on EdgeOne Fire (1.21 N cm) (p < .05). The most flexible (p < .05) were EdgeOne Fire (angle of rotation: 602.6°; maximum bending load: 251.4 g.f) and Reciproc Blue (533.2° and 235.6 g.f). There were no significant differences observed in the irrigation flow among the four domains generated by the tested instruments. CONCLUSIONS: Despite observing variations in the design, phase transformation temperatures, and in the torsional and bending test outcomes among the four heat-treated reciprocating instruments, no significant differences were found in the irrigation flow pattern among the different groups in the simulated root canal preparations.

Seasonal changes characterise the shark and ray assemblages in a subtropical shallow sandy habitat in the iSimangaliso Wetland Park, South Africa.

Understanding how environmental drivers influence shark and ray spatial and temporal patterns can provide crucial knowledge for their evidence-based protection and long-term monitoring. However, information on which drivers of variation are most important for elasmobranch communities on soft sediments is limited. Using baited remote underwater stereo-video systems (stereo-BRUVs), we investigated how seasonal and environmental variables affected the elasmobranchs of the iSimangaliso Wetland Park marine protected area (MPA) in South Africa (SA). In total, 11 species were identified from 48 sites between 12 m and 33 m water depth in a sandy habitat. While species richness was similar across seasons, the total abundance of elasmobranchs recorded was higher in winter than summer. The species assemblage composition varied significantly between seasons, with the Human's whaler shark Carcharhinus humani prevalent in summer and the Critically Endangered whitespotted wedgefish Rhynchobatus djiddensis more abundant during winter. Most species were sighted throughout the entire depth range, but rays were more common in shallower waters (< 25 m depth), while C. humani and R. djiddensis were more common in the deeper depth zone of this study. This research provides baseline information about this previously unexplored sandy habitat for elasmobranchs in a site of regional and global significance. Records of species of conservation concern in the sampling area highlight the importance of protecting sand environments within an MPA.

Invasive Pneumococcal Disease in People Living with HIV: A Retrospective Case-Control Study in Brazil.

HIV-infected patients are at particular risk for invasive pneumococcal disease (IPD). We describe cases of IPD in people living with HIV/AIDS (PLWHA) and find associated risk factors for infection and death. METHODS: A retrospective case-control study, nested in a cohort, including PLWHA with and without IPD, conducted in Brazil, 2005-2020. Controls were of the same gender/age and seen at the same time/place as cases. RESULTS: We identified 55 episodes of IPD (cases) in 45 patients and 108 controls. The incidence of IPD was 964/100,000 person-years. A total of 42 of 55 (76.4%) IPD episodes presented with pneumonia and 11 (20%) with bacteremia without a focus and 38/45 (84.4%) were hospitalized. Blood cultures were positive in 54/55 (98.2%). Liver cirrhosis and COPD were the only factors associated with IPD in PLWHA in univariate analysis, although no associated factors were found in multivariate analysis. Penicillin resistance was found in 4/45 (8.9%). Regarding antiretroviral therapy (ART), 40/45 (88.9%) cases vs. 80/102 controls (74.1%) were in use (p = 0.07). Patients with HIV and IPD had a higher CD4 count of 267 cells/mm3 compared with the control group, in which it was 140 cells/mm3 (p = 0.027). Pneumococcal vaccination was documented in 19%. Alcoholism (p = 0.018), hepatic cirrhosis (p = 0.003), and lower nadir CD4 count (p = 0.033) were associated with the risk of death in patients with IPD. In-hospital mortality among PLWHA and IPD was 21.1%, and it was associated with thrombocytopenia and hypoalbuminemia, elevated band forms, creatinine, and aspartate aminotransferase (AST). CONCLUSIONS: The incidence of IPD in PLWHA remained high despite ART. The vaccination rate was low. Liver cirrhosis was associated with IPD and death.

Ferroelectric Orthorhombic ZrO2 Thin Films Achieved Through Nanosecond Laser Annealing.

A new approach for the stabilization of the ferroelectric orthorhombic ZrO2 films is demonstrated through nanosecond laser annealing (NLA) of as-deposited Si/SiOx /W(14 nm)/ZrO2 (8 nm)/W(22 nm), grown by ion beam sputtering at low temperatures. The NLA process optimization is guided by COMSOL multiphysics simulations. The films annealed under the optimized conditions reveal the presence of the orthorhombic phase, as confirmed by X-ray diffraction, electron backscatter diffraction, and transmission electron microscopy. Macroscopic polarization-electric field hysteresis loops show ferroelectric behavior, with saturation polarization of 12.8 µC cm-2 , remnant polarization of 12.7 µC cm-2 and coercive field of 1.2 MV cm-1 . The films exhibit a wake-up effect that is attributed to the migration of point defects, such as oxygen vacancies, and/or a transition from nonferroelectric (monoclinic and tetragonal phase) to the ferroelectric orthorhombic phase. The capacitors demonstrate a stable polarization with an endurance of 6.0 × 105 cycles, demonstrating the potential of the NLA process for the fabrication of ferroelectric memory devices with high polarization, low coercive field, and high cycling stability.

A medicalização e a recente farmaceuticalização / Medicalization and the recent pharmaceuticalization

Este artigo buscadiscorrer, por meio de uma revisão narrativa dos descritivos de seus temas centrais, o escopo da já bastante pesquisada medicalização e brevemente contrapô-lo ao da farmaceuticalização, conceito mais recente com o qual guarda alguma justaposição, porém não absoluta. A farmaceuticalização se define como a escolha por um tratamento farmacológico, em detrimento de outros, o que incide diretamente sobre o número de prescrições e vendas farmacológicas e psicofarmacológicas no campo da saúde mental, sobre o qual nos deteremos. A venda psicofarmacológica neste setor vem expressando um aumento exponencial, conforme pesquisas. A farmaceuticalização passou a ser estudada sobretudo por pesquisadores do Ocidente (Estados Unidos e Europa), porém ainda com insuficiente publicação na América Latina e no Brasil

This article seeks to discuss, through a narrative review of its central descriptive-terms, the scope of the already well researched medicalisation, and briefly contrast it with that of pharmaceuticalization, a more recent concept with which it has some juxtaposition, although not absolute. Pharmaceuticalization is defined as the choice of a pharmacological treatment instead of other non-pharmacological ones, what affects the number of pharmacological and psychopharmacological prescriptions and sales in the field of mental health, on which we will focus. Psychopharmacological sales in this sector have been expressing an exponential increase, according to research. Pharmaceuticalization has been studied mainly by western researchers (mostly at the United States and Europe), but with little publication in Latin America and Brazil.

A SUBJETIVIDADE E O PSICOFÁRMACO / Subjectivity and the psychotropic drug

Este estudo teórico pretende, enquanto breve narrativa temática acerca de subjetividade e psicofármaco, abordar de forma crítica a escolha psicofarmacológica. Este tema, que inquieta a muitos há algum tempo, encontra-se em estado agudo: os números atuais são ainda mais alarmantes que antes e seguem crescendo. O fenômeno atualmente chamado de farmaceuticalização (ou farmacologização) ­ ou seja, a escolha por um fármaco em detrimento de outras opções não farmacológicas ­ incide diretamente sobre o consumo psicofarmacológico. Abordaremos o tema com ênfase sobre a subjetividade que busca o medicamento, até mesmo em uma vertente supostamente preventiva, para se evitar a dor psíquica e, em algumas vezes, o trabalho psíquico. Há uma subjetividade não-medicável, que parece se encontrar negada neste estado de coisas.

This theoretical study intends to, as a brief thematic narrative on subjectivity in relation to psychotropic drugs, discuss critically this state of affairs that is the use of psychopharmacological drugs. This subject, long and vastly researched, is in an acute state: the current figures are even more alarming than before. The phenomenon currently called pharmaceuticalization - that is, the choice of a drug instead of a non-pharmacological option - has a direct impact on psychopharmacological consumption. We will approach the theme with emphasis on the subjectivity that seeks medication, even in a supposedly preventive way, to avoid psychic pain and, sometimes, psychic work. There is a subjectivity not passive to medication that seems to be denied in this state of affairs.

Characterization of the file-specific heat-treated ProTaper Ultimate rotary system.

AIM: To compare design, metallurgy and mechanical performance of the ProTaper (PT) Ultimate system with instruments of similar dimensions from the ProGlider, PT Gold and PT Universal systems. METHODOLOGY: New PT Ultimate instruments (n = 248) were compared with instruments of similar dimensions from ProGlider (n = 31), PT Gold (n = 155) and PT Universal (n = 155) systems regarding their number of spirals, helical angle, blade symmetry, tip geometry, surface finishing, nickel/titanium ratio, phase transformation temperatures and mechanical performance. One-way anova and nonparametric Mood's median tests were used for statistical comparison (α = 5%). RESULTS: All instruments had symmetrical blades without radial lands or flat sides, similar surface finishing and an almost equiatomic nickel/titanium ratio, whilst the number of spirals, helical angles and the tip geometry were different. PT Ultimate instruments showed 3 distinct heat treatments that matched with the colour of their metal wire. Slider and ProGlider instruments had similar R-phase start (Rs) and R-phase finish (Rf) temperatures. SX, F1, F2, F3 and Shaper instruments showed equivalent heat treatments (Rs ~45.6°C and Rf ~28.3°C) that were similar to their PT Gold counterparts (Rs ~47.9°C and Rf ~28.2°C), but completely distinct to the PT Universal ones (Rs ~16.2°C and Rf ~-18.2°C). Amongst the PT Ultimate instruments, the lowest maximum torques were observed in the SX (0.44 N cm), Slider (0.45 N cm) and Shaper (0.60 N cm) instruments, whilst the highest was noted in the FXL (4.90 N cm). PT Ultimate Slider and ProGlider had similar torsional (~0.40 N cm) and bending loads (~145.0 gf) (p = 1.000), whilst the other PT Ultimate instruments showed statistically significantly lower maximum torque, higher angle of rotation and lower bending load (higher flexibility) than their counterparts of the PT Universal and PT Gold systems. CONCLUSIONS: The PT Ultimate system comprises instruments with 3 distinct heat treatments that showed similar phase transformation temperatures to their heat-treated analogues. PT Ultimate instruments presented lower torsional strength and superior flexibility than their counterparts, whilst maximum torque, angle of rotation and bending loads progressively increased with their sizes.

MBNL-dependent impaired development within the neuromuscular system in myotonic dystrophy type 1.

AIMS: Myotonic dystrophy type I (DM1) is one of the most frequent muscular dystrophies in adults. Although DM1 has long been considered mainly a muscle disorder, growing evidence suggests the involvement of peripheral nerves in the pathogenicity of DM1 raising the question of whether motoneurons (MNs) actively contribute to neuromuscular defects in DM1. METHODS: By using micropatterned 96-well plates as a coculture platform, we generated a functional neuromuscular model combining DM1 and muscleblind protein (MBNL) knock-out human-induced pluripotent stem cells-derived MNs and human healthy skeletal muscle cells. RESULTS: This approach led to the identification of presynaptic defects which affect the formation or stability of the neuromuscular junction at an early developmental stage. These neuropathological defects could be reproduced by the loss of RNA-binding MBNL proteins, whose loss of function in vivo is associated with muscular defects associated with DM1. These experiments indicate that the functional defects associated with MNs can be directly attributed to MBNL family proteins. Comparative transcriptomic analyses also revealed specific neuronal-related processes regulated by these proteins that are commonly misregulated in DM1. CONCLUSIONS: Beyond the application to DM1, our approach to generating a robust and reliable human neuromuscular system should facilitate disease modelling studies and drug screening assays.

Nesting Ecology of Lepidochelys olivacea in Lobito, Angola.

The scarcity on the Atlantic coast of the African sea turtle population and its dynamics data is well known. This article discusses the nesting ecology methods and analysis of a nascent Angolan project aimed at preserving the nesting female population of the Olive Ridley turtle (Lepidochelys olivacea) on the coast of Lobito. This study examines the nesting ecology of this species from 2020 to 2023. Females had an average CCL of 70.2 cm and CCW of 68.5 cm. These females laid 127 eggs in nests that averaged 47.0 cm deep. The ex situ nest incubation period averaged 60 days, and the hatchling success was 82.1%. Some techniques used in this project require modifications and enhancements. The utilization of photo identification did not yield the anticipated outcomes, prompting the adoption of passive integrated transponders (PITs) in the last season. However, due to limited funding, the success of this method is contingent upon an augmented field effort, allowing for the recapture of a larger number of females. The continuity of this project hinges upon collaboration between higher authorities and the local community. Together, it is possible to deepen the understanding of the nesting ecology of this species and address pivotal issues for its conservation, thereby implementing the most effective preservation measures.

High Piezoelectric Output Voltage from Blue Fluorescent N,N-Dimethyl-4-nitroaniline Nano Crystals in Poly-L-Lactic Acid Electrospun Fibers.

N,N-dimethyl-4-nitroaniline is a piezoelectric organic superplastic and superelastic charge transfer molecular crystal that crystallizes in an acentric structure. Organic mechanical flexible crystals are of great importance as they stand between soft matter and inorganic crystals. Highly aligned poly-l-lactic acid polymer microfibers with embedded N,N-dimethyl-4-nitroaniline nanocrystals are fabricated using the electrospinning technique, and their piezoelectric and optical properties are explored as hybrid systems. The composite fibers display an extraordinarily high piezoelectric output response, where for a small stress of 5.0 × 103 Nm-2, an effective piezoelectric voltage coefficient of geff = 4.1 VmN-1 is obtained, which is one of the highest among piezoelectric polymers and organic lead perovskites. Mechanically, they exhibit an average increase of 67% in the Young modulus compared to polymer microfibers alone, reaching 55 MPa, while the tensile strength reaches 2.8 MPa. Furthermore, the fibers show solid-state blue fluorescence, important for emission applications, with a long lifetime decay (147 ns) lifetime decay. The present results show that nanocrystals from small organic molecules with luminescent, elastic and piezoelectric properties form a mechanically strong hybrid functional 2-dimensional array, promising for applications in energy harvesting through the piezoelectric effect and as solid-state blue emitters.

Texturing Methods of Abrasive Grinding Wheels: A Systematic Review.

Creating textures on abrasive wheels is a strategy that allows a significant improvement in grinding operations. The reduction of the internal stresses in the workpiece and the temperature during the grinding operation generates an increase in the dimensional accuracy of the workpiece and a longer tool life. Textured abrasive wheels can be produced in many different ways. Depending on the processing method, the dimensional accuracy of the tool and its applicability is changed. Some methods can produce tools with three-dimensional grooves; there are also methods that are employed for the re-texturing of grooves after the grooved zone wears out. In the literature, the benefits of textured grinding wheels over traditional wheels have been extensively discussed. However, information on the particularities of texturing methods is still lacking. To clarify the advantages, limitations, and main advances regarding each of the groove production methods, the authors of this article carried out a systematic review. The objective of this work is to establish the factors that are affected by groove production methods and the technological advances in this area. The benefits and drawbacks of various grooving techniques are then reviewed, and potential study areas are indicated.

Experimental validation of a computational fluid dynamics model using micro-particle image velocimetry of the irrigation flow in confluent canals.

AIM: This study aimed to experimentally validate a computational fluid dynamics (CFD) model, using micro-particle image velocimetry (micro-PIV) measurements of the irrigation flow velocity field developed in confluent canals during irrigation with a side-vented needle. METHODOLOGY: A microchip with confluent canals, manufactured in polydimethylsiloxane was used in a micro-PIV analysis of the irrigation flow using a side-vented needle placed 3 mm from the end of the confluence of the canals. Velocity fields and profiles were recorded for flow rates of 0.017 and 0.1 ml/s and compared with those predicted in CFD numerical simulations (using a finite volume commercial code - FLUENT) for both laminar and turbulent regimes. RESULTS: The overall flow pattern, isovelocity and vector maps as well as velocity profiles showed a close agreement between the micro-PIV experimental and CFD predicted data. No relevant differences were observed between the results obtained with the laminar and turbulent flow models used. CONCLUSIONS: Results showed that the laminar CFD modelling is reliable to predict the flow in similar domains.