Point-by-point inscribed sapphire parallel fiber Bragg gratings in a fully multimode system for multiplexed high-temperature sensing.

We study the point-by-point inscription of sapphire parallel fiber Bragg gratings (sapphire pFBGs) in a fully multimode system. A parallel FBG is shown to be critical in enabling detectable and reliable high-order grating signals. The impacts of modal volume, spatial coherence, and grating location on reflectivity are examined. Three cascaded seventh-order pFBGs are fabricated in one sapphire fiber for wavelength multiplexed temperature sensing. Using a low-cost, fully multimode 850-nm interrogator, reliable measurement up to 1500°C is demonstrated.

Heat-induced drift reduction of time of flight in fused quartz acoustic waveguides via annealing process.

High temperature structural acoustic sensors play an important role in many applications. Fused quartz waveguide is a popular choice due to its resistance to harsh environments and its convenience of modification. However, time of flight between pulse and echo, which is widely used in these sensors, tends to encounter drifts in fast temperature changing process even after temperature returns to initial value. In this article, different annealing process are performed for a special modified fused quartz waveguide with a sensor node. Annealing treatment is found able to reduce the drift when the waveguide undergoes a sudden temperature spike to 1000 °C at 500 kHz operating acoustic frequency, and the best annealing condition could make the drift one magnitude smaller. A following temperature test up to 1000 °C shows consistent measurement readings.

Powder-in-Tube Reactive Molten-Core Fabrication of Glass-Clad BaO-TiO2-SiO2 Glass-Ceramic Fibers.

In this paper we report the fabrication of glass-clad BaO-TiO2-SiO2 (BTS) glass-ceramic fibers by powder-in-tube reactive molten-core drawing and successive isothermal heat treatment. Upon drawing, the inserted raw powder materials in the fused silica tubing melt and react with the fused silica tubing (housing tubing) via dissolution and diffusion interactions. During the drawing process, the fused silica tubing not only serves as a reactive crucible, but also as a fiber cladding layer. The formation of the BTS glass-ceramic structure in the core was verified by micro-Raman spectroscopy after the successive isothermal heat treatment. Second-harmonic generation and blue-white photoluminescence were observed in the fiber using 1064 nm and 266 nm picosecond laser irradiation, respectively. Therefore, the BTS glass-ceramic fiber is a promising candidate for all fiber based second-order nonlinear and photoluminescence applications. Moreover, the powder-in-tube reactive molten core method offers a more efficient and intrinsic contamination-free approach to fabricate glass-ceramic fibers.

Fully integrated fused quartz acoustic horns for structural health monitoring.

Non-destructive acoustic structural sensing is an imperative technology, applicable to many different fields such as aerospace and civil engineering. To maintain a high sensitivity or to mitigate acoustic loss, it is important to increase the signal-to-noise ratio by improving coupling efficiency from acoustic sources to the object under test, such as an acoustic waveguide. Here, a fully integrated fused quartz horn design is combined with a fused quartz acoustic waveguide. The resulting system is intended to demonstrate a high accuracy low cost alternative to current sensing systems and the present article report on the viability of using a merged acoustic horn and waveguide.

Mechanical properties of bioactive glasses, ceramics, glass-ceramics and composites: State-of-the-art review and future challenges.

The repair and restoration of bone defects in orthopaedic and dental surgery remains a major challenge despite advances in surgical procedures and post-operative treatments. Bioactive glasses, ceramics, glass-ceramics and composites show considerable potential for such applications as they can promote bone tissue regeneration. This paper presents an overview of the mechanical properties of various bioactive materials, which have the potential for bone regeneration. It also identifies current strategies for improving the mechanical properties of these novel materials, as these are rarely ideal as direct replacements for human bone. For this reason bioactive organic-inorganic composites and hybrids that have tailorable mechanical properties are of particular interest. The inorganic component (bioactive glass, ceramic or glass-ceramic) can provide both strength and bioactivity, while the organic component can add structural reinforcement, toughness and processability. Another topic presented in this paper includes 3D porous scaffolds that act as a template for cell attachment, proliferation and bone growth. Mechanical limitations of existing glass and ceramic scaffolds are discussed, along with the relevant challenges and strategies for further improvement. Advantages and disadvantages of different bioactive materials are critically examined. This paper is focused on optimization of biomaterials properties, in particular mechanical properties and bioactivity.

Application of Sapphire-Fiber-Bragg-Grating-Based Multi-Point Temperature Sensor in Boilers at a Commercial Power Plant.

Readily available temperature sensing in boilers is necessary to improve efficiencies, minimize downtime, and reduce toxic emissions for a power plant. The current techniques are typically deployed as a single-point measurement and are primarily used for detection and prevention of catastrophic events due to the harsh environment. In this work, a multi-point temperature sensor based on wavelength-multiplexed sapphire fiber Bragg gratings (SFBGs) were fabricated via the point-by-point method with a femtosecond laser. The sensor was packaged and calibrated in the lab, including thermally equilibrating at 1200 °C, followed by a 110-h, 1000 °C stability test. After laboratory testing, the sensor system was deployed in both a commercial coal-fired and a gas-fired boiler for 42 days and 48 days, respectively. The performance of the sensor was consistent during the entire test duration, over the course of which it measured temperatures up to 950 °C (with some excursions over 1000 °C), showing the survivability of the sensor in a field environment. The sensor has a demonstrated measurement range from room temperature to 1200 °C, but the maximum temperature limit is expected to be up to 1900 °C, based on previous work with other sapphire based temperature sensors.

Acoustic modal analysis of unique fused-silica fibers for passive non-destructive structural monitoring.

The goal of non-destructive acoustic sensing is to passively monitor innate structural parameters such as temperature, strain, and pressure. Intended for use in harsh structural environments, a distributed acoustic sensing system has been created using a single mode, radiation hardened, fused-silica core rod and a high-resolution acoustic sensor. This study aims to enhance the capabilities of the acoustic sensor by manipulating the fused-silica core rod, geometrically, to induce and control additional acoustic reflections. Here, two geometries are demonstrated to markedly improve upon previous fiber designs and result in a consistent acoustic profile.

Fiber Bragg grating fabricated in micro-single-crystal sapphire fiber.

This Letter introduces a fiber Bragg grating (FBG) in a micro-single-crystal sapphire fiber (micro-SFBG) for sensing applications in high-temperature and harsh environments. The FBG was fabricated by a point-by-point method via an IR-femtosecond laser in a large-diameter sapphire fiber that was then wet-hot acid etched to achieve microfiber size, which culminated in fabricating and characterizing a 9.6 µm diameter micro-SFBG. The refractive index measurement ranging from 1 to 1.75 and temperature measurement from room temperature to 1400°C are also reported.

Mechanically switchable polymer fibers for sensing in biological conditions.

The area of in vivo sensing using optical fibers commonly uses materials such as silica and polymethyl methacrylate, both of which possess much higher modulus than human tissue. The mechanical mismatch between materials and living tissue has been seen to cause higher levels of glial encapsulation, scarring, and inflammation, leading to failure of the implanted medical device. We present the use of a fiber made from polyvinyl alcohol (PVA) for use as an implantable sensor as it is an easy to work with functionalized polymer that undergoes a transition from rigid to soft when introduced to water. This ability to switch from stiff to soft reduces the severity of the immune response. The fabricated PVA fibers labeled with fluorescein for sensing applications showed excellent response to various stimuli while exhibiting mechanical switchability. For the dry fibers, a tensile storage modulus of 4700 MPa was measured, which fell sharply to 145 MPa upon wetting. The fibers showed excellent response to changing pH levels, producing values that were detectable in a range consistent with those seen in the literature and in proposed applications. The results show that these mechanically switchable fibers are a viable option for future sensing applications.

Sapphire-fiber-based distributed high-temperature sensing system.

We present, for the first time to our knowledge, a sapphire-fiber-based distributed high-temperature sensing system based on a Raman distributed sensing technique. High peak power laser pulses at 532 nm were coupled into the sapphire fiber to generate the Raman signal. The returned Raman Stokes and anti-Stokes signals were measured in the time domain to determine the temperature distribution along the fiber. The sensor was demonstrated from room temperature up to 1200°C in which the average standard deviation is about 3.7°C and a spatial resolution of about 14 cm was achieved.

Review and the state of the art: Sol-gel and melt quenched bioactive glasses for tissue engineering.

Biomaterial development is currently the most active research area in the field of biomedical engineering. The bioglasses possess immense potential for being the ideal biomaterials due to their high adaptiveness to the biological environment as well as tunable properties. Bioglasses like 45S5 has shown great clinical success over the past 10 years. The bioglasses like 45S5 were prepared using melt-quenching techniques but recently porous bioactive glasses have been derived through sol-gel process. The synthesis route exhibits marked effect on the specific surface area, as well as degradability of the material. This article is an attempt to provide state of the art of the sol-gel and melt quenched bioactive bioglasses for tissue regeneration. Fabrication routes for bioglasses suitable for bone tissue engineering are highlighted and the effect of these fabrication techniques on the porosity, pore-volume, mechanical properties, cytocompatibilty and especially apatite layer formation on the surface of bioglasses is analyzed in detail. Drug delivery capability of bioglasses is addressed shortly along with the bioactivity of mesoporous glasses. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 104B: 1248-1275, 2016.

Temperature dependence of sapphire fiber Raman scattering.

Anti-Stokes Raman scattering in sapphire fiber has been observed for the first time. Temperature dependence of Raman peaks' intensity, frequency shift, and linewidth were also measured. Three anti-Stokes Raman peaks were observed at temperatures higher than 300°C in a 0.72-m-long sapphire fiber excited by a second-harmonic Nd YAG laser. The intensity of anti-Stokes peaks are comparable to that of Stokes peaks when the temperature increases to 1033°C. We foresee the combination of sapphire fiber Stokes and anti-Stokes measurement in use as a mechanism for ultrahigh temperature sensing.

Magnetic sensing with ferrofluid and fiber optic connectors.

A simple, cost effective and sensitive fiber optic magnetic sensor fabricated with ferrofluid and commercially available fiber optic components is described in this paper. The system uses a ferrofluid infiltrated extrinsic Fabry-Perot interferometer (EFPI) interrogated with an infrared wavelength spectrometer to measure magnetic flux density. The entire sensing system was developed with commercially available components so it can be easily and economically reproduced in large quantities. The device was tested with two different ferrofluid types over a range of magnetic flux densities to verify performance. The sensors readily detected magnetic flux densities in the range of 0.5 mT to 12.0 mT with measurement sensitivities in the range of 0.3 to 2.3 nm/mT depending on ferrofluid type. Assuming a conservative wavelength resolution of 0.1 nm for state of the art EFPI detection abilities, the estimated achievable measurement resolution is on the order 0.04 mT. The inherent small size and basic structure complimented with the fabrication ease make it well-suited for a wide array of research, industrial, educational and military applications.

A review of bioactive glasses: Their structure, properties, fabrication and apatite formation.

Bioactive glass and glass-ceramics are used in bone repair applications and are being developed for tissue engineering applications. Bioactive glasses/Bioglass are very attractive materials for producing scaffolds devoted to bone regeneration due to their versatile properties, which can be properly designed depending on their composition. An important feature of bioactive glasses, which enables them to work for applications in bone tissue engineering, is their ability to enhance revascularization, osteoblast adhesion, enzyme activity and differentiation of mesenchymal stem cells as well as osteoprogenitor cells. An extensive amount of research work has been carried out to develop silicate, borate/borosilicate bioactive glasses and phosphate glasses. Along with this, some metallic glasses have also been investigated for biomedical and technological applications in tissue engineering. Many trace elements have also been incorporated in the glass network to obtain the desired properties, which have beneficial effects on bone remodeling and/or associated angiogenesis. The motivation of this review is to provide an overview of the general requirements, composition, structure-property relationship with hydroxyapatite formation and future perspectives of bioglasses.Attention has also been given to developments of metallic glasses and doped bioglasses along with the techniques used for their fabrication.

ZrO2 thin-film-based sapphire fiber temperature sensor.

A submicrometer-thick zirconium dioxide film was deposited on the tip of a polished C-plane sapphire fiber to fabricate a temperature sensor that can work to an extended temperature range. Zirconium dioxide was selected as the thin film material to fabricate the temperature sensor because it has relatively close thermal expansion to that of sapphire, but more importantly it does not react appreciably with sapphire up to 1800 °C. In order to study the properties of the deposited thin film, ZrO2 was also deposited on C-plane sapphire substrates and characterized by x-ray diffraction for phase analysis as well as by atomic force microscopy for analysis of surface morphology. Using low-coherence optical interferometry, the fabricated thin-film-based sapphire fiber sensor was tested in the lab up to 1200 °C and calibrated from 200° to 1000 °C. The temperature resolution is determined to be 5.8 °C when using an Ocean Optics USB4000 spectrometer to detect the reflection spectra from the ZrO2 thin-film temperature sensor.

Long period gratings in random hole optical fibers for refractive index sensing.

We have demonstrated the fabrication of long period gratings in random hole optical fibers. The long period gratings are fabricated by a point-by-point technique using a CO(2) laser. The gratings with a periodicity of 450 µm are fabricated and a maximum coupling efficiency of -9.81 dB has been achieved. Sensing of different refractive indices in the surrounding mediums is demonstrated by applying standard liquids with refractive indices from 1.400 to 1.440 to the long period grating.

Porous capillary tubing waveguide for multigas sensing.

This Letter reports simultaneous acetylene and carbon monoxide gas sensing by using a porous hollow-core waveguide. Compared to evanescent wave based gas sensors, the hollow-core waveguide can have a much better sensitivity because the majority of the light-wave energy propagating in the hollow core can interact directly with the gas molecules. The wall of the waveguide is made porous by the phase separating and leaching of the initial glass tubing. This allows the gas molecules to easily penetrate into the sensor providing the sensor with a very fast response time compared to other waveguide based gas sensors. A gas chamber system was constructed to simultaneously measure the presence of acetylene and carbon monoxide gases, and the testing results clearly indicate the high sensitivity and fast response time of this sensor.

Silica-antibiotic hybrid nanoparticles for targeting intracellular pathogens.

We investigated the capability of biodegradable silica xerogel as a novel carrier of antibiotic and the efficacy of treatment compared to that with the same dose of free drug against murine salmonellosis. The drug molecules (31%) entrapped in the sol-gel matrix remained in biologically active form, and the bactericidal effect was retained upon drug release. The in vitro drug release profiles of the gentamicin from the xerogel and that from the xerogel-polyethylene glycol (PEG) were distinctly different at pH 7.4. A delayed release of gentamicin was observed from the silica xerogel network (57% in 33 h), and with the addition of 2% PEG, the release rate reached 90% in 33 h. Administration of two doses of the silica xerogel significantly reduced the Salmonella enterica serovar Typhimurium load in the spleens and livers of infected AJ 646 mice. The silica xerogel and xerogel-PEG achieved a 0.45-log and a 0.41-log reduction in the spleens, respectively, while for the free drug there was no reduction. On the other hand, silica xerogel and xerogel-PEG achieved statistically significant 1.13-log and 1.15-log reductions in the livers, respectively, while for the free drug the reduction was a nonsignificant value of 0.07 log. This new approach, which utilizes a room-temperature synthetic route for incorporating therapeutic drugs into the silica matrix, should improve the capability for targeting intracellular pathogens.

Bending-induced optical loss in random-hole optical fibers.

We present the experimentally determined optical bend loss for random hole optical fibers in the spectral range 1520 to 1570 nm induced by wrapping the optical fiber around a fixed diameter mandrel. The optical losses are compared to those obtained for a single-mode fiber and a multimode fiber using the same bending procedures. The bending induced optical losses in the random hole optical fibers were several orders of magnitude lower than for the single-mode fiber and were about 1 order of magnitude lower than for the multimode fiber.

Core-suction technique for the fabrication of optical fiber preforms.

A novel technique, named "core suction," for fabricating optical fiber preforms has been devised. The technique involves drawing the molten nonconventional core glass material into the cladding tube to form the preform. The developed technique is simple, inexpensive, and shows great potential for fabricating preforms of highly nonlinear nonconventional glasses as the core material. Preforms were made with Schott SF6 and a lead-tellurium-germanate glass in silica cladding tubes, and these preforms were then pulled into fibers.