Selected ice nanoparticle accelerator hypervelocity impact mass spectrometer (SELINA-HIMS): features and impacts of charged particles.

The selected ice nanoparticle accelerator, SELINA, was used to prepare beams of single ice particles with positive or negative charge. Positively charged particles were prepared from deionized water and 0.05-0.2 molar solutions of sodium chloride in water, and negatively charged ice particles were generated from water without salt. Depending on the electrospray source configuration, the measured particles vary from 50 to 1000 nm in diameter. The kinetic energy per charge for all particles was set to 200 eV by the collisional equilibration in quadrupoles, which resulted in primary velocities up to 600 m/s for the lowest m/z particles. The electrospray ionization and thus particle formation from SELINA become less efficient with increasing salt concentration, resulting in a lower detected particle frequency and size. Good instrument operation is achievable for concentrations below 0.2 M. After we have verified and characterized positively and negatively charged ice particles, we have combined SELINA with a target and time-of-flight spectrometer for a 'proof-of-principle' post acceleration of 120 nm particles towards hypervelocity (v ~ 3000 m/s) and detection of fragments from the particle impact (SELINA-HIMS). General conditions are discussed for the acceleration of particles between 50 and 1000 nm to velocities well above 3000 m/s with SELINA-HIMS instrument. This article is part of the theme issue 'Dust in the Solar System and beyond'.

Advances and Challenges in the Analysis of Boswellic Acids by Separation Methods.

Boswellia resin is an exudate from the cut bark of Boswellia trees. The main constituents of pharmacological interest are boswellic acids (pentacyclic triterpenoids), namely α-boswellic acid, ß-boswellic acid, 3-O-acetyl-α-boswellic acid, 3-O-acetyl-ß-boswellic acid, 11-keto-ß-boswellic acid, and 3-O-acetyl-11-keto-ß-boswellic acid. Nowadays, dietary supplements with Boswellia serrata extract are used in the treatment of inflammatory joint diseases. Additionally, the constituents of Boswellia resin have shown potential for the treatment of other chronic inflammatory diseases and various types of cancer. Separation methods including ultra/high-performance liquid chromatography, gas chromatography, thin layer chromatography, supercritical fluid chromatography, and capillary electrochromatography coupled with UV or MS detection have been used for the determination of boswellic acids in various matrices (mostly plant material and biological samples). This review aims to provide a comprehensive summary of these separation methods, offering a critical discussion of their strengths and limitations in the analysis of boswellic acids. The knowledge of various separation methods plays a pivotal role in the quality control of herbal dietary supplements and the monitoring of the metabolism and pharmacokinetics of their constituents. The approaches based on metabolomics and network pharmacology represent new ways of fingerprinting secondary metabolites in Boswellia resin increasing the comprehensiveness of the output of these methods resulting in safer dietary supplements.

Reactivity of the Ethenium Cation (C2H5+) with Ethyne (C2H2): A Combined Experimental and Theoretical Study.

The gas-phase reaction between the ethyl cation (C2H5+) and ethyne (C2H2) is re-investigated by measuring absolute reactive cross sections (CSs) and branching ratios (BRs) as a function of collision energy, in the thermal and hyperthermal energy range, via tandem-guided ion beam mass spectrometry under single collision conditions. Dissociative photoionization of C2H5Br using tuneable VUV radiation in the range 10.5-14.0 eV is employed to generate C2H5+, which has also allowed us to explore the impact of increasing (vibrational) excitation on the reactivity. Reactivity experiments are complemented by theoretical calculations, at the G4 level of theory, of the relative energies and structures of the most relevant stationary points on the reactive potential energy hypersurface (PES) and by mass-analyzed ion kinetic energy (MIKE) spectrometry experiments to probe the metastable decomposition from the [C4H7]+ PES and elucidate the underlying reaction mechanisms. Two main product channels have been identified at a centre-of-mass collision energy of ∼0.1 eV: (a) C3H3++CH4, with BR = 0.76±0.05 and (b) C4H5++H2, with BR = 0.22±0.02. A third channel giving C2H3+ in association with C2H4 is shown to emerge at both high internal excitation of C2H5+ and high collision energies. From CS measurements, energy-dependent total rate constants in the range 4.3×10-11-5.2×10-10 cm3·molecule-1·s-1 have been obtained. Theoretical calculations indicate that both channels stem from a common covalently bound intermediate, CH3CH2CHCH+, from which barrierless and exothermic pathways exist for the production of both cyclic c-C3H3+ and linear H2CCCH+ isomers of the main product channel. For the minor C4H5+ product, two isomers are energetically accessible: the three-member cyclic isomer c-C3H2(CH3)+ and the higher energy linear structure CH2CHCCH2+, but their formation requires multiple isomerization steps and passages via transition states lying only 0.11 eV below the reagents' energy, thus explaining the smaller BR. Results have implications for the modeling of hydrocarbon chemistry in the interstellar medium and the atmospheres of planets and satellites as well as in laboratory plasmas (e.g., plasma-enhanced chemical vapor deposition of carbon nanotubes and diamond-like carbon films).

Charged Ice Particle Beams with Selected Narrow Mass and Kinetic Energy Distributions.

Small ice particles play an important role in atmospheric and extraterrestrial chemistry. Circumplanetary ice particles that are encountered by space probes at hypervelocities play a critical role in the determination of surface and subsurface properties of their source bodies. Here we present an apparatus for the generation of low-intensity beams of single mass-selected charged ice particles under vacuum. They are produced via electrospray ionization of water at atmospheric pressure and undergo evaporative cooling when transferred to vacuum through an atmospheric vacuum interface. m/z selection is achieved through two subsequent quadrupole mass filters operated in the variable-frequency mode within a range of m/z values between 8 × 104 and 3 × 107. Velocity and charge of the selected particles are measured using a nondestructive single-pass image charge detector. From the known electrostatic acceleration potentials and settings of the quadrupoles the particle masses could be obtained and be accurately controlled. It has been shown that the droplets are frozen within the transit time of the apparatus such that ice particles are present after the quadrupole stages and finally detected. The demonstrated correspondence between particle mass and specific quadrupole potentials in this device allows preparation of beams of single particles with a repetition rate between 0.1 and 1 Hz with various diameter distributions from 50 to 1000 nm at 30-250 eV of kinetic energy per charge. This corresponds to velocities and particle masses quickly available between 600 m/s (80 nm) and 50 m/s (900 nm) and particle charge numbers (positive) between 103 and 104[e], depending upon size.

Characterization of Triacylglycerol Estolide Isomers Using High-Resolution Tandem Mass Spectrometry with Nanoelectrospray Ionization.

Triacylglycerol estolides (TG-EST) are biologically active lipids extensively studied for their anti-inflammatory and anti-diabetic properties. In this work, eight standards of TG-EST were synthesized and systematically investigated by nanoelectrospray tandem mass spectrometry. Mass spectra of synthetic TG-EST were studied with the purpose of enabling the unambiguous identification of these lipids in biological samples. TG-EST glycerol sn-regioisomers and isomers with the fatty acid ester of hydroxy fatty acid (FAHFA) subunit branched in the ω-, α-, or 10-position were used. Ammonium, lithium, and sodium adducts of TG-EST formed by nanoelectrospray ionization were subjected to collision-induced dissociation (CID) and higher-energy collisional dissociation (HCD). Product ion spectra allowed for identification of fatty acid (FA) and FAHFA subunits originally linked to the glycerol backbone and distinguished the α-branching site of the FAHFA from other estolide-branching isomers. The ω- and 10-branching sites were determined by combining CID with ozone-induced dissociation (OzID). Lithium adducts provided the most informative product ions, enabling characterization of FA, hydroxy fatty acid (HFA), and FAHFA subunits. Glycerol sn-regioisomers were distinguished based on the relative abundance of product ions and unambiguously identified using CID/OzID of lithium and sodium adducts.

OLYMPIA-LILBID: A New Laboratory Setup to Calibrate Spaceborne Hypervelocity Ice Grain Detectors Using High-Resolution Mass Spectrometry.

The coupling of an Orbitrap-based mass analyzer to the laser-induced liquid beam ion desorption (LILBID) technique has been investigated, with the aim to reproduce the mass spectra recorded by Cassini's Cosmic Dust Analyzer (CDA) in the vicinity of Saturn's icy moon Enceladus. LILBID setups are usually coupled with time-of-flight (TOF) mass analyzers, with a limited mass resolution (∼800 m/Δm). Thanks to the Orbitrap technology, we developed a unique analytical setup that is able to simulate hypervelocity ice grains' impact in the laboratory (at speeds in the range of 15-18 km/s) with an unprecedented high mass resolution of up to 150 000 m/Δm (at m/z 19 for a 500 ms signal duration). The results will be implemented in the LILBID database and will be useful for the calibration and future data interpretation of the Europa Clipper's SUrface Dust Analyzer (SUDA), which will characterize the habitability of Jupiter's icy moon Europa.

The Influence of the Geometry of Movement during the Friction Process on the Change in the Tribological Properties of 30CrNiMo8 Steel in Contact with a G40 Steel Ball.

Experiments with changes in motion geometry can provide valuable data for engineering and development purposes, allowing a better understanding of the influence of tribological factors on the performance and service life of joints. The presented subject article focused on the experimental investigation of the influence of the geometry of the movement of the friction process on the change in the tribological properties of 30CrNiMo8 steel. The friction process was carried out without the use of a lubricant in contact with a steel ball of G40 material with a diameter of 4.76 mm. The steel ball performed two types of movement on the surface of the experimental material. The first method used was ball on disc, in which the ball moved reciprocally in an oval direction at an angle of 180° on a circumferential length of 35 mm at a speed of 5 mm/s. The second method consists of the same input parameters of the measurement, with the difference that the path along which the ball moved had a linear character. The load during the experiment was set at a constant value of 50 N with 1000 repetitions. The results show that with the ball on disc method, there was an increase in wear by 147% compared to the linear test method, which was approximately a coefficient of increase in wear of 2.468. EDS analysis pointed to the occurrence of oxidative wear that affected the resulting COF values, which were lower by 8% when using the ball on disc method due to a more uniform distribution of O and C on the surface of the friction groove where these elements acted as solid microlubricants. With the ball on disc method, defects in the form of microcracks occurred, which affected the reduction in the values of the depth of the affected area of microhardness.

Reactions of permethyltitanocene tucked-in derivatives with carbon dioxide.

Both single tucked-in permethyltitanocene 1 and double tucked-in permethyltitanocene 2 react with excess CO2 by insertion into their Ti-CH2 bonds. The former one precipitates instantly a yellow carboxylate-tethered oligomer [3]n which is insoluble in aprotic solvents and in a vacuum it sublimes as a monomer without decomposition. Computations for n ≤ 4 optimised the structure of the monomer [3] and showed that open chain oligomers bound by dative O → Ti bonds were not sterically hindered. The latter bond dissociates when [3]n is oxidized by chlorination with CDCl3 or CD2Cl2 to give Ti(IV) chloride 4 or upon metathesis of [3]n with Me3SiCl yielding Ti(III) chloride 5. Oxidative addition of MeCN affords a C-C coupled dinuclear titanocene diimine 6. Compound [3]n also reacts with 1 to give the tethered carbodiolate 8 or with [Cp*2TiH] (where Cp* = η5-C5Me5) to give the half-tethered carbodiolate 10. The non-tethered carbodiolate 12 was obtained from [Cp*2TiH] and CO2 yielding titanocene formate by reaction of the latter with another equivalent of [Cp*2TiH]. All these carbodiolates contain Ti(III) metal atoms forming electronic triplet states of axial or orthorhombic symmetry. In contrast to the rapidly reacting 1 compound 2 reacts with excess CO2 slowly in m-xylene at 100 °C using only one of its two Ti-CH2 moieties. The structure of the obtained carbodiolate 13 indicates that the primary product analogous to 3 reacts with 2 more rapidly than with CO2.

Coupling of chiral and achiral stationary phases in supercritical fluid chromatography: Evaluating and improving retention prediction.

Isomers and stereoisomers are always challenging to separate. Column coupling may provide improved chromatographic selectivity, necessary for the separation of the compounds with similar chemical and structural properties. The relatively low viscosity of supercritical fluids, used as mobile phases allows for the coupling of several columns in series in supercritical fluid chromatography (SFC), without exceeding the pressure limits of the system. The aim of this study is to propose reliable prediction of the retention behaviour of analytes on a coupled column system, based on a limited number of initial analyses. The chiral compounds atenolol, ephedrine, propranolol, mianserin, labetalol and nadolol, besides the diastereomers quinine and quinidine, and the structural isomers of aminophenol and aminocresol were used as model analytes. The retention behaviour of the analytes was determined on the individual chiral columns Lux Cellulose-1, Lux Cellulose-2, Lux Cellulose-3, Lux Cellulose-4, Lux Amylose-2 and the achiral columns Luna NH2, Luna Silica, Synergi RP and FluoroSep RP. The mobile phase was composed of CO2 mixed with 20% (v/v) MeOH, which contained 0.1% (v/v) trifluoroacetic acid and 0.1% (v/v) isopropylamine. The retention factors of the analytes on coupled stationary phases were predicted, and subsequently compared to the experimentally obtained ones. Relative deviations of predicted and experimental retention factors were in range from 0.00% to 51.91%. Flow rate and back pressure of the screening conditions were adjusted to improve prediction precision on four column combinations, with varying success rates. The average relative deviations of retention factors were reduced to 2.84% - 6.59% by adjusting flow rate, and to 2.30% - 8.57% by adjusting back pressure. The most successful approach, flow rate adjustment, was then applied to select a column combination providing improved resolution of the structurally similar components of silymarin extract.

Development of a capillary electrophoresis method for the separation of flavonolignans in silymarin complex.

CE method for the baseline separation of structurally similar flavonolignans silybin A, silybin B, isosilybin A, isosilybin B, silychristin, silydianin, and their precursor taxifolin in silymarin complex has been developed and validated. The optimized background electrolyte was 100 mmol/L boric acid (pH 9.0) containing 5 mmol/L heptakis(2,3,6-tri-O-methyl)-ß-CD and 10% (v/v) of methanol. The separation was carried out in an 80.5/72 cm (50 µm id) fused silica capillary at +25 kV with UV detection at 200 nm. Genistein (10 µg/mL) was used as internal standard. The resolution between the diastereomers of silybin and isosilybin was 1.73 and 2.59, respectively. The method was validated for each analyte in a concentration range of 2.5-50 µg/mL. The calibration curves were rectilinear with correlation coefficients ≥0.9972. The method was applied to determine flavonolignans in two dietary supplements containing Silybum marianum extract. The accuracy was evaluated by comparing the results of the CE analyses of the dietary supplements with those of the reference United States Pharmacopeial HPLC method. The unpaired t-test did not show a statistically significant difference between the results of both the proposed CE and the reference method (p > 0.05, n = 3).

Sensitivity of secondary electrospray ionization mass spectrometry to a range of volatile organic compounds: Ligand switching ion chemistry and the influence of Zspray™ guiding electric fields.

RATIONALE: Secondary electrospray ionization (SESI) is currently only semi-quantitative. In the Zspray™ arrangement of SESI-MS, the transfer of ions from near atmospheric pressure to a triple quadrupole is achieved by guiding electric fields that partially desolvate both reagent and analyte ions which must be understood. Also, to make SESI-MS more quantitative, the mechanisms and the kinetics of the reaction processes, especially ligand switching reactions of hydrated hydronium reagent ions, H3 O+ (H2 O)n , with volatile organic compound (VOC) molecules, need to be understood. METHODS: A modified Zspray™ ESI ion source operating at sub-atmospheric pressure with analyte sample gas introduced via an inlet coaxial with the spray was used. Variation of the ion-guiding electric fields was used to reveal the degree of desolvation of both reagent and analyte ions. The instrument sensitivity was determined for several classes of VOCs by introducing bag samples of suitably varying concentrations as quantified on-line using selected ion flow tube MS. RESULTS: Electric field desolvation resulted in largely protonated VOCs, MH+ , and their monohydrates, MH+ H2 O, and for some VOCs proton-bound dimer ions, MH+ M, were formed. There was a highly linear response of the ion signal to the measured VOC sample concentration, which provided the instrument sensitivities, S, for 25 VOCs. The startling results show very wide variations in S from near 0 to 1 for hydrocarbons, and up to 100, on a relative scale, for polar compounds such as monoketones and unsaturated aldehydes. CONCLUSIONS: The complex ion chemistry occurring in the SESI ion source, largely involving gas-phase ligand switching, results in widely variable sensitivities for different classes of VOCs. The sensitivity is observed to depend on the dipole moment and proton affinity of the analyte VOC molecule, M, and to decrease with the observed fraction of MH+ H2 O, but other yet unrecognized factors must play a significant role.

Stability study of α-bromophenylacetic acid: Does it represent an appropriate model analyte for chiral separations?

The stability of α-bromophenylacetic acid (BPAA) in 50% aqueous methanol solution has been tested. CE in different running buffers was used to separate BPAA from the decomposition reaction products α-hydroxyphenylacetic (mandelic) acid and α-methoxyphenylacetic acid. Suitable CE separation of all three compounds and other product, bromide, was achieved in 60 mmol/L formate buffer (pH 3.0) at -30 kV in 50 µm (i.d.) poly(vinyl alcohol)-coated fused silica capillary (30 cm/24.5 cm) with UV detection at 200 nm. The CE method was applied to determine the reaction order of the decomposition of BPAA (0.47 mmol/L) via nucleophilic substitution in 50% aqueous methanol. The first-order reaction kinetics was confirmed by linear and non-linear regression, giving the rate constants 1.52 × 10-4 ± 2.76 × 10-5 s-1 and 7.89 × 10-5 ± 5.02 × 10-6 s-1, respectively. Additionally, the degradation products were identified by CE coupled to mass spectrometric (MS) detection. The CE-MS experiments carried out in 60 mmol/L formate buffer (pH 3.0) and in 60 mmol/L acetate buffer (pH 5.0) confirmed the results obtained by CE-UV. Furthermore, the stability of BPAA in polar solvents was tested by 1H NMR experiments. Our results provide strong evidence of the instability and fast degradation of BPAA in 50% aqueous methanol indicating that BPAA is not suitable as the model analyte for chiral separations.

Resonant states in cyanogen NCCN.

In a combined experimental and theoretical study we probe the transient anion states (resonances) in cyanogen. Experimentally, we utilize electron energy loss spectroscopy which reveals the resonance positions by monitoring the excitation functions for vibrationally inelastic electron scattering. Four resonances are visible in the spectra, centered around 0.36 eV, 4.1, 5.3 and 7.3 eV. Theoretically, we explore the resonant states by using the regularized analytical continuation method. A very good agreement with the experiment is obtained for low-lying resonances, however, the computational method becomes unstable for higher-lying states. The lowest shape resonance (2Πu) is independently explored by the complex adsorbing potential method. In the experiment, this resonance is manifested by a pronounced boomerang structure. We show that the naive picture of viewing NCCN as a pseudodihalogen and focusing only on the CC stretch is invalid.

State-Selected Reactivity of Carbon Dioxide Cations ( CO 2 + ) With Methane.

The reactivity of CO 2 + with CD4 has been experimentally investigated for its relevance in the chemistry of plasmas used for the conversion of CO2 in carbon-neutral fuels. Non-equilibrium plasmas are currently explored for their capability to activate very stable molecules (such as methane and carbon dioxide) and initiate a series of reactions involving highly reactive species (e.g., radicals and ions) eventually leading to the desired products. Energy, in the form of kinetic or internal excitation of reagents, influences chemical reactions. However, putting the same amount of energy in a different form may affect the reactivity differently. In this paper, we investigate the reaction of CO 2 + with methane by changing either the kinetic energy of CO 2 + or its vibrational excitation. The experiments were performed by a guided ion beam apparatus coupled to synchrotron radiation in the VUV energy range to produce vibrationally excited ions. We find that the reactivity depends on the reagent collision energy, but not so much on the vibrational excitation of CO 2 + . Concerning the product branching ratios ( CD 4 + / CD 3 + /DOCO+) there is substantial disagreement among the values reported in the literature. We find that the dominant channel is the production of CD 4 + , followed by DOCO+ and CD 3 + , as a minor endothermic channel.

Development of micellar electrokinetic chromatography method for the determination of three defined impurities in indomethacin.

A micellar electrokinetic chromatography method for the determination of indomethacin impurities (4-chlorobenzoic acid, 5-methoxy-2-methyl-3-indoleacetic acid, and 3,4-dichloroindomethacin) has been developed. A 64.5/56-cm fused silica 50 µm id capillary with extended light path (150 µm id) detection window was used. Internal standard was 1-naphthylacetic acid. The analytes were separated at 30 kV with DAD detection at 224 nm. A central composite face-centered design was applied for the optimization of the separation conditions. The effect of SDS concentration, content of methanol, concentration of phosphate buffer, and pH of the buffer were studied at three levels. The optimized background electrolyte was 20 mmol/L phosphate buffer (pH 7.57) containing 58 mmol/L SDS and 0% MeOH. Sufficient resolution of all compounds with Rs ≥ 3.5 was achieved within 10 min. The method was validated for a range of 1.25-80 µg/mL of each impurity corresponding to 0.05-3.2% relative to the concentration of indomethacin (2.5 mg/mL). The calibration curves were rectilinear with correlation coefficients r2 exceeding 0.9994. The lower limit of quantification was 0.05% or 1.25 µg/mL that complies with the reporting limits regarding the ICH Q3A guideline. The method was applied to purity assay of indomethacin in both bulk drug and gel.

The reaction of C5N- with acetylene as a possible intermediate step to produce large anions in Titan's ionosphere.

A theoretical and experimental investigation of the reaction C5N- + C2H2 has been carried out. This reaction is of astrophysical interest since the growth mechanism of large anions that have been detected in Titan's upper atmosphere by the Cassini plasma spectrometer are still largely unknown. The experimental studies have been performed using a tandem quadrupole mass spectrometer which allows identification of the different reaction channels and assessment of their reaction thresholds. Results of these investigations were compared with the predictions of ab initio calculations, which identified possible pathways leading to the observed products and their thermodynamical properties. These computations yielded that the majority of these products are only accessible via energy barriers situated more than 1 eV above the reactant energies. In many cases, the thresholds predicted by the ab initio calculations are in good agreement with the experimentally observed ones. For example, the chain elongation reaction leading to C7N-, although being slightly exoergic, possesses an energy barrier of 1.91 eV. Therefore, the title reaction can be regarded to be somewhat unlikely to be responsible for the formation of large anions in cold environments such as interstellar medium or planetary ionospheres.

Effects of collision energy and vibrational excitation of CH3+ cations on its reactivity with hydrocarbons: But-2-yne CH3CCCH3 as reagent partner.

The methyl carbocation is ubiquitous in gaseous environments, such as planetary ionospheres, cometary comae, and the interstellar medium, as well as combustion systems and plasma setups for technological applications. Here we report on a joint experimental and theoretical study on the mechanism of the reaction CH3+ + CH3CCCH3 (but-2-yne, also known as dimethylacetylene), by combining guided ion beam mass spectrometry experiments with ab initio calculations of the potential energy hypersurface. Such a reaction is relevant in understanding the chemical evolution of Saturn's largest satellite, Titan. Two complementary setups have been used: in one case, methyl cations are generated via electron ionization, while in the other case, direct vacuum ultraviolet photoionization with synchrotron radiation of methyl radicals is used to study internal energy effects on the reactivity. Absolute reactive cross sections have been measured as a function of collision energy, and product branching ratios have been derived. The two most abundant products result from electron and hydride transfer, occurring via direct and barrierless mechanisms, while other channels are initiated by the electrophilic addition of the methyl cation to the triple bond of but-2-yne. Among the minor channels, special relevance is placed on the formation of C5H7+, stemming from H2 loss from the addition complex. This is the only observed condensation product with the formation of new C-C bonds, and it might represent a viable pathway for the synthesis of complex organic species in astronomical environments and laboratory plasmas.

Electrochemical Oxidation of [1-X-12-I-CB11Me10-] Anions: Formation of Borenium Ylides [12-Dehydro-1-X-CB11Me10] and Iodonium Ylide Anions [{12-(1-X-CB11Me10-)}2I+].

Cyclic voltammograms of 12-iodinated icosahedral carborane anions [1-X-12-I-CB11Me10-] (X = H, CH3, C2H5, C3H7, C4H9, C6H13, and COOCH3) show two one-electron anodic oxidation peaks at the Pt electrode in liquid SO2. Oddly, the first is irreversible and the second partially reversible. Mass spectrometry of the principal anionic product of preparative anodic oxidation of [1-H-12-I-CB11Me11-], identical with the anionic product of its reaction with [Et3Si-H-SiEt3]+ and/or Et3Si+, allows it to be identified as the iodonium ylide anion [{12-(1-H-CB11Me10-)}2I+]. Its reversible oxidation to a neutral ylide radical [{12-(1-H-CB11Me10•)}{12-(1-H-CB11Me10-)}I+] is responsible for the second peak. A DFT geometry optimization suggests that both the ylide anion and the ylide radical are very crowded and have an unusually large C-I-C valence angle of ∼132°; they are the first compounds with two bulky highly methylated CB11 cages attached to the same atom. Molecular iodine is another product of the electrolysis. We propose an electrode mechanism in which initial one-electron oxidation of [1-X-12-I-CB11Me10-] is followed by a transfer of an iodine atom from the B-I bond to SO2 to yield a weakly bound radical ISO2• which disproportionates into SO2 and I2. The other product is the borenium ylide [12-dehydro-1-X-CB11Me10], which has a strongly Lewis acidic naked vertex in position 12 that rapidly adds to another [1-X-12-I-CB11Me10-] anion to form the observed stable ylide anion [{12-(1-X-CB11Me10-)}2I+]. In acetonitrile, where it presumably exists as a solvent adduct, [12-dehydro-1-X-CB11Me10] has been trapped with H2O and, to a small extent, with MeOH, but not with several other potential trapping agents.

Is the Reaction of C3N(-) with C2H2 a Possible Process for Chain Elongation in Titan's Ionosphere?

The reaction of C3N(-) with acetylene was studied using three different experimental setups, a triple quadrupole mass spectrometer (Trento), a tandem quadrupole mass spectrometer (Prague), and the "CERISES" guided ion beam apparatus at Orsay. The process is of astrophysical interest because it can function as a chain elongation mechanism to produce larger anions that have been detected in Titan's ionosphere by the Cassini Plasma Spectrometer. Three major products of primary processes, C2H(-), CN(-), and C5N(-), have been identified, whereby the production of the cyanide anion is probably partly due to collisional induced dissociation. The formations of all these products show considerable reaction thresholds and also display comparatively small cross sections. Also, no strong signals of anionic products for collision energies lower than 1 eV have been observed. Ab initio calculations have been performed to identify possible pathways leading to the observed products of the title reaction and to elucidate the thermodynamics of these processes. Although the productions of CN(-) and C5N(-) are exoergic, all reaction pathways have considerable barriers. Overall, the results of these computations are in agreement with the observed reaction thresholds. Due to the existence of considerable reaction energy barriers and the small observed cross sections, the title reaction is not very likely to play a major role in the buildup of large anions in cold environments like the interstellar medium or planetary and satellite ionospheres.

A Pilot Study of Ion - Molecule Reactions at Temperatures Relevant to the Atmosphere of Titan.

Reliable theoretical models of the chemical kinetics of the ionosphere of Saturn's moon, Titan, is highly dependent on the precision of the rates of the reactions of ambient ions with hydrocarbon molecules at relevant temperatures. A Variable Temperature Selected Ions Flow Tube technique, which has been developed primarily to study these reactions at temperatures within the range of 200-330 K, is briefly described. The flow tube temperature regulation system and the thermalisation of ions are also discussed. Preliminary studies of two reactions have been carried out to check the reliability and efficacy of kinetics measurements: (i) Rate constants of the reaction of CH3+ ions with molecular oxygen were measured at different temperatures, which indicate values in agreement with previous ion cyclotron resonance measurements ostensibly made at 300 K. (ii) Formation of CH3+ ions in the reaction of N2+ ions with CH4 molecules were studied at temperatures within the range 240-310 K which showed a small but statistically significant decrease of the ratio of product CH3+ ions to reactant N2+ ions with reaction temperature.