High efficient COVID-19 waste co-pyrolysis char/TiO2 nanocomposite for photocatalytic reduction of Cr(VI) under visible light.

Titanium dioxide (Titania) nanoparticle-coated biochar derived through co-pyrolysis of COVID-19 waste face mask (WFM) and Moringa oleifera seed cake (MO) provides an effective way to alleviate toxic metal in wastewater. This study investigates the effects of Biochar/titania photocatalyst preparation, characterization, and its photoreduction of Cr(VI). The morphological and functional modifications in the catalyst were identified using X-Ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, ultraviolet spectrophotometer, surface area analysis, and Raman spectrophotometer, respectively. The influencing parameters, namely, pH, photocatalyst dosage, initial pollutant concentration, and visible light irradiation time, have been investigated. The findings reveal that the Cr(VI) reduction by the photocatalyst was highly facilitated by photocatalytic process. The prepared photocatalyst shows higher and faster reduction rate of Cr(VI) and also improves the catalyst stability. The photoreduction of Cr(VI) ensembles well with pseudo-first order kinetics. At 180 min of reaction time, maximum Cr(VI) reduction of 98.65% was achieved at pH 2, 0.3 g/L catalyst dosage, and 10 ppm initial concentration, respectively. The synthesized photocatalyst shows excellent recycling performance up to 7 times, and these studies proved that the prepared catalyst is cost-effective and efficiently employed for removing pollutants.

Investigation of thermodynamic and kinetic parameters of Albizia lebbeck seed pods using thermogravimetric analysis.

Thermodynamic and kinetic studies are very necessary to evaluate the conversion efficiency of biomass to energy. Therefore, this current work reported the thermodynamic and kinetic parameters of Albizia lebbeck seed pods through thermogravimetric analysis, which was carried out at temperatures from 25 °C to 700 °C, and heating rates of 5, 10, 15, and 20 °C/min. Apparent activation energies were determined by applying three iso-conversional model-free methods including Kissinger-Akahira-Sunose (KAS), Ozawa-Flynn-Wall (OFW), and Starink. Resultantly, average apparent activation energy values for the three models of KAS, OFW, and Starink were found to be 155.29, 156.14, and 155.53 kJ/mol, respectively. In addition, thermodynamic triplets such as enthalpy, Gibbs free energy, and entropy were obtained as 151.16 kJ/mol, 150.64 kJ/mol, and -7.57 J/mol·K, respectively. The above results suggest Albizia lebbeck seed pods could become a potential source for bioenergy production aiming to achieve the sustainable goal and waste-to-energy strategy.

Derivation of synthetic fuel from waste plastic: investigation of engine operating characteristics on DI diesel engine.

The utilization of plastic in day to day life is ever-increasing and has generated a large amount of plastic garbage that needs proper disposal to save the environment from harmful pollution. The plastic waste management becomes a pressing concern in the present scenario in developing countries like India. This research article evaluates the potential of synthetic fuel (SF) derived from waste plastics collected from the local shops. In this current investigation, the SF blends are tested in a direct injection diesel engine to analyze the performance and emission characteristics of the engine. Three different blends were made namely SF20, SF40, and SF60 on a volumetric basis and the tests were carried out. From the experimental results, it was found that brake thermal efficiency (BTE) of the fuel blends was reduced as compared with neat diesel operation regardless of loads whereas SF20 showed a similar trend as that of diesel operation. The analysis of the emission characteristics revealed that the SF20 blends reduced dangerous smoke and carbon monoxide emission as compared with other test fuels. From the overall results, SF20 showed superior performance and emission aspects as compared with other SF blends whereas the engine operated smoothly up to 60% of SF blending at all loading conditions.

Generation of biodiesel from industrial wastewater using oleaginous yeast: performance and emission characteristics of microbial biodiesel and its blends on a compression injection diesel engine.

Microbial-derived biodiesel was tested on a lab scale CI diesel engine for carrying out exhaust emission and performance characteristics. The performance, emission, and combustion characteristics of a single cylinder four stroke fixed compression ratio engine when fueled with microbial bio-diesel and its 10-30% blends with diesel (on a volume basis) were investigated and compared with conventional diesel. The bio-diesel was obtained from microbes which were grown by combining distillery spent wash with lignocellulosic hydrolysate at nutrient deprived conditions. The microbes consumed the wastes and converted the high strength waste water into lipids, which were trans-esterified to form bio-diesel. Testing of microbial bio-diesel blends with ordinary diesel at different loading pressures and the emission characteristics were compared. Results indicate that with increasing of the blends, reduction of HC and CO emissions were observed, whilst brake thermal efficiency maxed out at 20% blending. Further increase of blends showed a tendency of increasing of both emissions in the exhaust stream. The Brake Specific Fuel consumption was observed to decline with blending until 20% and then increased. The nitrogen oxide emissions, however, were found to increase with increasing blend ratios and reached a maximum at 20% blend. The escalation of HC, CO, CO2, and NOx emissions was also observed at higher blending ratios and higher engine loads. The performance studies were able to show that out of the three blends of biodiesel, 20% biodiesel blend was able to deliver the best of reduced hydrocarbon and carbon monoxide emissions, whilst also delivering the highest Brake thermal efficiency and the lowest Brake Specific Fuel consumption.

Experimental assessment and multi-response optimization of diesel engine performance and emission characteristics fuelled with Aegle marmelos seed cake pyrolysis oil-diesel blends using Grey relational analysis coupled principal component analysis.

This research focuses on the detailed experimental assessment of compression ignition (CI) engine behavior fuelled with Aegle marmelos (AM) seed cake pyrolysis oil blends. The study on effects of engine performance and emission a characteristic was designed using L25 orthogonal array (OA). These multi-objectives were normalized through gray relational analysis (GRA). Likewise, the principal component analysis (PCA) was performed to assess the weighting values respective to every performance and emission characteristics. The variability induced by using the input process parameters was allocated using analysis of variance (ANOVA). Hence, GRA-coupled PCA were employed to determine the optimal combination of CI engine control factors. The greater combination of engine characteristics levels were selected with F5 and W5. The higher brake thermal efficiency (BTE) have been obtained for F20 fuel as 22.01% at peak engine load, which is 11.43% for diesel. At peak load condition, F20 fuel emits 14.99% lower HC and 18.52% lower CO as compared to diesel fuel. The improved engine performance and emission characters can be attained by setting the optimal engine parameter combination as F20 blend at full engine load condition. The validation experiments show an improved average engine performance of 67.36% and average lower emission of 64.99% with the composite desirability of 0.8458.

Experimental investigation and exergy analysis on homogeneous charge compression ignition engine fueled with natural gas and diethyl ether.

In this work, diethyl ether (DEE) and compressed natural gas (CNG) port fuel injection (PFI) was investigated in direct injection (DI) compression ignition engine to determine the performance, combustion, and emission behaviors. In dual fuel mode, DEE and neat diesel were used as fuel energy, whereas in homogeneous charge compression ignition (HCCI) mode, DEE, and CNG were used as fuel energy. The engine behavior was analyzed for different inlet charge temperatures. Exergy analysis has been carried out for analyzing the various availability shares in the engine. The maximum brake thermal efficiency of the engine increased at peak load from 27.31% in neat diesel to 29.12% for dual fuel mode (D + CNG). Hydrocarbon and carbon monoxide emissions were reduced and oxides of nitrogen increased with the inlet charge heating mode. Maximum exergy efficiency was observed as 57.1% in dual fuel operation. The result of this work proves that CNG in dual and HCCI are effective for engine operation.

Characterization of pyrolysis bio-oil derived from intermediate pyrolysis of Aegle marmelos de-oiled cake: study on performance and emission characteristics of C.I. engine fueled with Aegle marmelos pyrolysis oil-blends.

The present research focuses on the analyzing the characteristics of bio-oil derived from intermediate pyrolysis of Aegle marmelos (AM) seed cake and its suitability for C.I. engine adaptation. Owing to the high volatile matter content of 73.69%, Aegle marmelos biomass was selected as the feedstock for this research. The intermediate pyrolysis was carried out at 600 °C in a 2-kg fixed bed type pyrolysis reactor at a heating rate of 10 °C/min and the obtained bio-oil was characterized by different analytical methods. As per American Society for Testing and Materials (ASTM) standards, physicochemical properties of the bio-oil were tested and it was observed that bio-oil is a highly viscous fluid with low calorific value. Analysis of bio-oil through FT-IR and GC-MS examination confirmed the presence of phenol, esters, alkyl, and oxygenated compounds. The performance and emission testing of direct injection diesel engine were conducted with various bio-oil blends and the results were compared with baseline diesel fuel. The experimental results showed that the addition of bio-oil decreased BTE (%) while increasing the BSEC (MJ/kW-h). At the same time, increasing the bio-oil ratio with diesel decreases dangerous emissions such as carbon monoxide and oxides of nitrogen emissions in the engine exhaust. According to engine test result, it was suggested that up to 20% of AM bio-oil (F20) can be employed as engine fuel for better engine operating characteristics.

Studies on the effects of storage stability of bio-oil obtained from pyrolysis of Calophyllum inophyllum deoiled seed cake on the performance and emission characteristics of a direct-injection diesel engine.

The highly unbalanced nature of bio-oil composition poses a serious threat in terms of storage and utilization of bio-oil as a viable fuel in engines. So it becomes inevitable to study the variations in physicochemical properties of the bio-oil during storage to value its chemical instability, for designing stabilization methodologies. The present study aims to investigate the effects of storage stability of bio-oil extracted from pyrolyzing Calophyllum inophyllum (CI) deoiled seed cake on the engine operating characteristics. The bio-oil is produced in a fixed bed reactor at 500 °C under the constant heating rate of 30 °C/min. All the stability analysis methods involve an accelerated aging procedure based on standards established by ASTM (D5304 and E2009) and European standard (EN 14112). Gas chromatography-mass spectrometry was employed to analytically characterize the unaged and aged bio-oil samples. The results clearly depict that stabilizing Calophyllum inophyllum bio-oil with 10% (w/w) methanol improved its stability than that of the unstabilized sample thereby reducing the aging rate of bio-oil to 0.04 and 0.13 cst/h for thermal and oxidative aging respectively. Engine testing of the bio-oil sample revealed that aged bio-oil samples deteriorated engine performance and increased emission levels at the exhaust. The oxidatively aged sample showed the lowest BTE (24.41%), the highest BSEC (20.14 MJ/kWh), CO (1.51%), HC (132 ppm), NOx (1098 ppm) and smoke opacity (34.8%).

Assessment of n-pentanol/Calophyllum inophyllum/diesel blends on the performance, emission, and combustion characteristics of a constant-speed variable compression ratio direct injection diesel engine.

Alcohol is used as an additive for a long time with the petroleum-based fuels. In this study, the higher alcohol, n-pentanol, was used as an additive to Calophyllum inophyllum (CI) biodiesel/diesel blends at 10, 15, and 20% by volume. In all blends, the ratio of CI was maintained at 20% by volume. The engine characteristics of the pentanol fuel blends were compared with the diesel and CI20 (Calophyllum inophyllum 20% and diesel 80%) biodiesel blend. The nitrogen oxide (NO) emission of the pentanol fuel blends showed an increased value than CI20 and neat diesel fuel. The carbon dioxide (CO2) also increased with increase in pentanol addition with the fuel blends than CI20 fuel blend and diesel. The carbon monoxide (CO) and hydrocarbon (HC) emissions were decreased with increase in pentanol proportion in the blend than the CI20 fuel and diesel. The smoke emission was reduced and the combustion characteristics of the engine were also improved by using pentanol blended fuels. From this investigation, it is suggested that 20% pentanol addition with the biodiesel/diesel fuel is suitable for improved performance and combustion characteristics of a diesel engine without any engine modifications, whereas CO2 and NO emissions increased with addition of pentanol due to effective combustion.

Analytical characterization of products obtained from slow pyrolysis of Calophyllum inophyllum seed cake: study on performance and emission characteristics of direct injection diesel engine fuelled with bio-oil blends.

This paper aims to analyse the characteristics and properties of the fractions obtained from slow pyrolysis of non-edible seed cake of Calophyllum inophyllum (CI). The gas, bio-oil and biochar obtained from the pyrolysis carried out at 500 °C in a fixed bed batch type reactor at a heating rate of 30 °C/min were characterized by various analytical techniques. Owing to the high volatile content of CI biomass (72.61%), it was selected as the raw material in this present investigation. GC-MS and FT-IR analysis of bio-oil showed the presence of higher amount of oxygenated compounds, phenol derivatives, esters, acid and furans. The physicochemical properties of the bio-oil were tested as per ASTM norms which imply that bio-oil is a highly viscous liquid with lower heating value as compared to that of diesel fuel. The chemical composition of evolved gas was analysed by using GC testing which revealed the presence of combustible components. The FT-IR characterization of biochar showed the presence of aliphatic and aromatic hydrocarbons whereas the elevated amount of carbon in biochar indicates its potential to be used as solid fuel. The performance and emission characteristics of CI engine were assessed with different CI bio-oil blends and compared with baseline diesel fuel. The results showed that addition of bio-oil leads to decreased brake thermal efficiency and increased brake specific energy consumption. Meanwhile, increase in blend ratio reduces harmful pollutants such as oxides of nitrogen and smoke in the exhaust. From the engine testing, it is suggested to employ 20% of CI bio-oil blends in CI engine to obtain better operation.