Effect of soaking and single/two cycle high pressure treatment on water absorption, color, morphology and cooked texture of brown rice.

Water absorption, color, morphology and cooked texture of brown rice were evaluated after selected soaking (30-50 °C, 30 min) and high pressure treatment (HPT) (100-500 MPa; single or two cycle; total holding time 10 min). Water absorption ratio and lightness values of brown rice were increased by soaking and HPT. Hardness and gumminess values of cooked brown rice were reduced while springiness and cohesiveness were elevated by HPT. Scanning electron microscopy indicated that HPT improved the texture of brown rice by disrupting the structure of rice bran layer, which allowed easier water penetration into the rice grain during cooking. Moreover, the two cycle HPT resulted in lighter color and softer texture for cooked brown rice than single cycle HPT primarily caused by the more severe structural disruption of bran layer. Overall, two cycle HPT after soaking could potentially improve the quality of brown rice, taking about the same time as the single cycle HPT. Further, the quality improvements with the two cycle HPT were facilitated at lower pressure levels thereby providing better commercial processing opportunities.

Characterization of Chinese liquor aroma components during aging process and liquor age discrimination using gas chromatography combined with multivariable statistics.

Chinese liquor aroma components were characterized during the aging process using gas chromatography (GC). Principal component and cluster analysis (PCA, CA) were used to discriminate the Chinese liquor age which has a great economic value. Of a total of 21 major aroma components identified and quantified, 13 components which included several acids, alcohols, esters, aldehydes and furans decreased significantly in the first year of aging, maintained the same levels (p > 0.05) for next three years and decreased again (p < 0.05) in the fifth year. On the contrary, a significant increase was observed in propionic acid, furfural and phenylethanol. Ethyl lactate was found to be the most stable aroma component during aging process. Results of PCA and CA demonstrated that young liquor (fresh) and aged liquors were well separated from each other, which is in consistent with the evolution of aroma components along with the aging process. These findings provide a quantitative basis for discriminating the Chinese liquor age and a scientific basis for further research on elucidating the liquor aging process, and a possible tool to guard against counterfeit and defective products.

Effect of high pressure treatment on the aging characteristics of Chinese liquor as evaluated by electronic nose and chemical analysis.

Several high pressure (HP) treatments (100-400 MPa; 15 and 30 min) were applied to Chinese "Junchang" liquor, and aging characteristics of the liquor were evaluated. Results from the principal component analysis and the discriminant factor analysis of E-Nose demonstrated that HP treatment at 300 and 400 MPa resulted in significant (p < 0.05) changes in aroma components of the liquor. An increase in total ester content and a decrease in total acid content were observed for all treated samples (p < 0.05), which was verified by gas chromatography analysis. In addition, a slight decrease in alcohol content was found for HP treatment at 400 MPa for 30 min. These changes and trends were in accordance with the natural aging process of Chinese liquor. However, HP treatment caused a slight increase in solid content, which might be somewhat undesirable. Sensory evaluation results confirmed that favorable changes in color and flavor of Chinese liquor were induced by HP treatment; however, overall gaps still existed between the quality of treated and six-year aged samples. HP treatment demonstrated a potential to accelerate the natural aging process for Chinese liquor, but long term studies may be needed further to realize the full potential.

Effect of high-pressure on calorimetric, rheological and dielectric properties of selected starch dispersions.

Effects of high-pressure (HP) treatment on the rheological, thermal and dielectric properties of the four selected starch dispersions (two modified starches, one native and one resistant) were evaluated. Differential scanning calorimetry (DSC) and oscillatory rheometry were employed to assess the extent of starch gelatinization and the developed gel rigidity (G') of starch gels after HP treatment. It was observed that starch dispersions gelatinized completely at 500 MPa with a 30-min holding time. The HP-treated starch samples exhibited predominantly solid-like (G'>G") behavior except for the resistant starch. Pressure-induced gel rigidity differed significantly among starch samples. The G' of starch gels increased with the pressure (400-600 MPa) in the studied frequency range (0.1-10 Hz) except for the native starch where a marginal decrease was recorded at similar condition. The holding time (15-30 min) and concentration (20-25% w/w) significantly attributed towards gel rigidity of starch samples. Measurement of dielectric properties of HP-treated samples over the frequency range 450-4450 MHz indicated differences in the dielectric constant (ɛ'), loss factor (ɛ") and penetration depth among starch gels. Pressure did not show any effect on dielectric property of the resistant starch sample. Power penetration depth decreased significantly with frequency and with the pressure.

SS-Stabilizing Proteins Rationally: Intrinsic Disorder-Based Design of Stabilizing Disulphide Bridges in GFP.

Abstract The most attractive and methodologically convenient way to enhance protein stability is via the introduction of disulphide bond(s). However, the effect of the artificially introduced SS-bond on protein stability is often quite unpredictable. This raises the question of how to choose the protein sites in an intelligent manner, so that the 'fastening' of these sites by the SS-bond(s) would provide maximal protein stability. We hypothesize that the successful design of a stabilizing SS-bond requires finding highly mobile protein regions. Using GFP as an illustrative example, we demonstrate that the knowledge of the peculiarities of the intramolecular hydrophobic interactions, combined with the understanding of the local intrinsic disorder propensities (that can be evaluated by various disorder predictors, e.g., PONDRFIT), is sufficient to find the candidate sites for the introduction of stabilizing SS-bridge(s). In fact, our analysis revealed that the insertion of the engineered SS-bridge between two highly flexible regions of GFP noticeably increased the conformational stability of this protein toward the thermal and chemical unfolding. Therefore, our study represents a novel approach for the rational design of stabilizing disulphide bridges in proteins.

Biological evaluation and interaction of a newly designed anti-cancer Pd(II) complex and human serum albumin.

The pharmacokinetics and pharmacodynamics of any drug will depend, largely, on the interaction that has with human serum albumin (HSA), the most abundant plasma protein. The interaction between newly synthesized Pd(II) complexe, 2,2'-bipyridin Butylglycinato Pd(II) nitrate, an anti-tumor component, with HSA was studied at different temperatures by fluorescence, far UV circular dichroism (CD), UV-visible spectrophotometry and theoretical approaches. The Pd(II) complex has a strong ability to quench the intrinsic fluorescence of HSA through a dynamic quenching procedure. The binding parameters and thermodynamic parameters, including δH°, δS° and δG° were calculated by fluorescence quenching method, indicated that hydrophobic forces play a major role in the interaction of Pd(II) complex with HSA. Based on Autodock, FRET (fluorescence resonance energy transfer) and fluorescence quenching data, it may be concluded that one of the binding sites in the complex of HSA is near the only one Trp of HSA (Trp214) in sub domain IIA of the protein. Far-UV-CD results indicated that Pd(II)-complex induced increase in the α-helical content of the protein. The anti-tumor property of the synthesized Pd(II) complex was studied by testing it on human tumor cell line K562. The 50% cytotoxic concentration (Cc50) of complex was determined using MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide) assay. Also, fluorescence staining with DAPI (4,6-diamidino-2-phenylindole) revealed some typical nuclear changes that are characteristic of apoptosis which is induced at Cc50 concentration of Pd(II) complex in K562 cell line after 24 h incubation. Our results suggest that Pd(II) complex is a promising anti-proliferative agent and should execute its biological effects by inducing apoptosis.

Evaluation of thermal properties of food materials at high pressures using a dual-needle line-heat-source method.

Thermal properties of food systems at high pressure (HP) are important in the design and operation of HP processing equipment. Available techniques for thermal property evaluation under HP conditions are still very limited. In this study, a dual-needle line-heat-source (DNL) device was installed in an HP vessel to evaluate thermal conductivity (k), diffusivity (alpha), and volumetric heat capacity (C(pV)) of foods at high pressure. The DNL probe was calibrated using glycerin (0.1 MPa) and 2% (w/w) agar gel (0.1 to 350 MPa) at 5 and 25 degrees C. Calibration results showed a good correlation with the reference data of pure water: R(2)= 0.966 for thermal conductivity and R(2)= 0.837 for diffusivity, and a small standard deviation of relative error (3.18%) for the volumetric heat capacity. Fresh potato and cheddar cheese were used as test samples at 5 degrees C at selected pressure levels (0.1 to 350 MPa). The potato samples gave thermal properties very close to those of pure water, but much higher than those of the cheese. The k and alpha values of both potato and cheese increased with pressure and a 2nd-order polynomial well fitted their pressure dependency. The volumetric heat capacity data did not show a clear pressure-dependency trend. The experimental system worked well for the evaluation of thermal properties at pressures up to 350 MPa.

Radio frequency heating of foods: principles, applications and related properties--a review.

Radio frequency (RF) heating is a promising technology for food applications because of the associated rapid and uniform heat distribution, large penetration depth and lower energy consumption. Radio frequency heating has been successfully applied for drying, baking and thawing of frozen meat and in meat processing. However, its use in continuous pasteurization and sterilization of foods is rather limited. During RF heating, heat is generated within the product due to molecular friction resulting from oscillating molecules and ions caused by the applied alternating electric field. RF heating is influenced principally by the dielectric properties of the product when other conditions are kept constant. This review deals with the current status of RF heating applications in food processing, as well as product and system specific factors that influence the RF heating. It is evident that frequency level, temperature and properties of food, such as viscosity, water content and chemical composition affect the dielectric properties and thus the RF heating of foods. Therefore, these parameters should be taken into account when designing a radio frequency heating system for foods.

Effect of high-hydrostatic pressure and temperature on rheological characteristics of glycomacropeptide.

The influences of high pressure and temperature on the rheological characteristics of glycomacropeptide (GMP) were studied using a controlled rate rheometer. GMP dispersions at a concentration of 12.5% (w/w) were subjected to high pressure from 100 to 400 MPa for 30 min and temperature from 20 to 80 degrees C for 15 min followed by rheological measurements at a shear rate ranged between 0 and 200 s-1. Shear stress-shear rate data of both pressure and heat induced GMP samples fitted Herschel-Bulkley model well with yield stress. It exhibited shear-thinning behavior with flow behavior index ranged between 0.882 and 0.996. Consistency coefficient and apparent viscosity increased with pressure up to 300 MPa while those parameters decreased at 400 MPa. The rheology of GMP was influenced by temperature. The consistency coefficient and apparent viscosity at 100 s-1 obeyed the Arrhenius relationship with activation energies ranged between 8.17 to 12.38 kJ/mol. Lower activation energy signified lesser molecular aggregation or unfolding of protein molecules during thermal treatment of GMP.

An investigation of sugar extraction methods and the use of microwave power for date syrup processing: efficiency and color related considerations.

This study investigates the effect of extraction methods on the color of date syrup and the potential use of microwave power for syrup processing. Sugar solutions were extracted from dates by boiling, soaking and blending. Color and sugar content of the extracted solutions were measured, and the percentage of sugar extracted form the total fruit sugar determined. Boiling was found to be the most efficient method of extraction whereby 74% of total samples sugar was extracted. In contrast, only 54.2% of fruit sugar was extracted by blending and 42% by soaking. In addition, solutions extracted by soaking and blending had a foaming problem in the subsequent concentration process. The extraction method had no effect on the product final color. The extracted solution was concentrated using two heating methods: conventional and microwave heating at a 600 W capacity and a frequency of 2450 MHz applied at three power levels: 10, 7, and 6. In the heating process, 180 minutes were needed to achieve a 77% degrees Brix using convective heating, while it took 81, 138, and 166 minutes of microwave heating at power level 10, 7, and 6, respectively to achieve the same concentration. Water activity of the syrup was measured within a sugar content range of 50 to 80% degrees Brix and the sugar concentration at which the product is shelf stable was determined at 76%.

A role for accessibility to self-peptide-self-MHC complexes in intrathymic negative selection.

Whether intrathymic-positive and -negative selection of conventional alpha beta T cells occur in anatomically distinct sites is a matter of debate. By using a system composed of two distinct immune receptors, the Y-Ae mAb and the 1H3.1 (V alpha 1/V beta 6) TCR, both directed against the 52--68 fragment of the I-E alpha-chain (E alpha 52--68) bound to I-A(b), we examined the occurrence of negative selection imposed in vivo by a self-peptide-self-MHC class II complex with differential tissue expression. 1H3.1 TCR-transgenic (Tg) mice were bred to mice having an I-E alpha transgene with expression directed to all MHC class II-positive cells, restricted to thymic epithelial cells, or restricted to B cells, dendritic cells, and medullary thymic epithelial cells. All 1H3.1 TCR/I-E alpha double-Tg mice revealed a severely diminished thymic cellularity. Their lymph node cells were depleted of V beta 6(+)CD4(+) cells and were unresponsive to E alpha 52--68 in vitro. The absolute number of CD4(+)CD8(+) thymocytes was drastically reduced in all combinations, indicating that negative selection caused by an endogenously expressed self-determinant can effectively occur in the thymic cortex in vivo. Moreover, both cortical epithelial cells and, interestingly, the few cortical dendritic cells were able to support negative selection of CD4(+)CD8(+) thymocytes, albeit with a distinct efficiency. Collectively, these observations support a model where, in addition to the avidity of the thymocyte/stromal cell interaction, in vivo negative selection of autoreactive TCR-Tg T cells is determined by accessibility to self-peptide-self-MHC complexes regardless of the anatomical site.

High-pressure destruction kinetics of Listeria monocytogenes on pork.

Packaged fresh pork chops (30-g samples) containing an indigenous bacterial population of approximately 10(7) CFU/g were inoculated with 10(7) CFU of Listeria monocytogenes Scott A per g, heat sealed, and subjected to high-pressure processing at 200 to 400 MPa for up to 90 min. Total counts and the number of surviving L. monocytogenes cells were determined by a spread plate technique on tryptic soy agar and modified Oxford medium, respectively. The pressure destruction was characterized by a dual-behavior, consisting of a step change in the number of survivors (Pk0) with the application of a pressure pulse and a first-order rate drop in the number of survivors during the pressure hold period. Higher pressures resulted in higher rates of microbial inactivation, as indicated by their associated lower D values (and higher k values). The pressure sensitivities of the kinetic parameters were evaluated on the basis of Arrhenius and pressure death time (PDT)-type models. The results suggested that L. monocytogenes was more resistant to pressure inactivation than the indigenous microflora (the volume change of activation, deltaV* [Arrhenius model]), and Zp values (PDT model) were -4.17 x 10(-5) m3 mole(-1) and 134 MPa for indigenous microflora and -3.43 x 10(-5) m3 mole(-1) and 163 MPa for L. monocytogenes respectively.

Heat transfer and lethality considerations in aseptic processing of liquid/particle mixtures: a review.

Consumer awareness and demand for nutritious yet inexpensive food products call for innovative processing techniques that have both safety and quality as primary objectives. These challenges appear to have been met by aseptic processing techniques, especially for liquid and high-acid foods. However, the extension of aseptic processing principles to low-acid foods containing discrete particles in viscous sauces has not been approved by regulatory agencies, particularly in North America. This apparent limitation is due primarily to the lack of adequate temperature monitoring devices to keep track of particles in dynamic motion, as well as to the residence time distribution of particles flowing in the continuous heat-hold-cool sections of the aseptic processing system. These problems have prompted active research to describe the phenomenal behavior of particulates through sound mathematical modeling and computer simulators. The accuracy of mathematical models depends heavily on how accurate input parametric values are. These parameters include the thermophysical properties of the carrier fluid and particles, as well as the aseptic processing system characteristics in relation to residence time distribution and the fluid-to-particle interfacial heat transfer coefficient. Apparently, several contradictory findings have been reported in the literature with respect to the effect of various processing parameters on the above-mentioned input parametric values. The need therefore arises for more collaborative studies involving the industry and academia. This review brings to perspective, the current status on the aseptic processing of particulate foods with respect to the critical processing parameters which affect the fluid-to-particle convective heat transfer coefficient associated with particulate laden products.