Visualizing Local Morphology and Conductivity Switching in Interface-Assembled Nanoporous C60 Thin Films.

Carbon materials promise a revolution in optoelectronics, medical applications, and sensing provided that their morphology can be controlled down to the nanometer scale. Nanoporous materials are particularly appealing as they offer a drastically enlarged interfacial area compared to the corresponding planar materials. Entire fields such as organic solar cells, catalysis, or sensing may profit from an enlarged interface and facilitated molecular interaction between a carbon material and the environment. Nanoporous fullerene thin films obtained by the deposition of suspended nanoclusters of fullerene were already reported but suffered from the limitation of the size of these particles to over 100 nm. We study here a complementary method based on interfacial self-assembly forcing C60 clusters to spontaneously form 2D percolating monolayers with most morphological features in the 5-20 nm range. Analysis of these films by means of electron microscopy and scanning probe microscopy proved their morphology to be a nanocomposite of crystalline beads embedded in an amorphous matrix of fullerenes. When contacted between two gold electrodes, these films show an intrinsic conductivity switching behavior. Their electrical conductivity could be reversibly switched on by applying a threshold electrical current and switched off by exposure to oxygen. Interestingly, the on-state exhibits an astonishing conductivity of over 10-3 S/m. Kelvin probe force microscopy (KFM) was used to observe local changes in the distribution of electrical potential upon switching, on the relevant length scale of a few nanometers.

Monitoring the transformation of aliphatic and fullerene molecules by high-energy electrons using surface-enhanced Raman spectroscopy.

We report on using 100 keV electrons to obtain amorphous carbon from aliphatic and fullerene molecules, and study this process by monitoring their Raman signal. In this regard, we use self-assembled monolayers of gold nanoparticles to provide high electromagnetic field enhancement, which allows the detection of the Raman signal from even nanometer-thick layers of analyte. Our results show different dynamics in the amorphization process of the two molecules, although both show suppression of their original vibrational resonances even at low exposure doses. We have also used atomic-force microscopy to evaluate the sensitivity of the C60 molecules to electron beams in forming networks of amorphized molecules that are less soluble in the development process. This method allows precise patterning possibilities as well as in situ functionalization of carbonaceous thin films in the perspective of using in electronic device applications.

Resistive switching of alkanethiolated nanoparticle monolayers patterned by electron-beam exposure.

Carbon-based electronic devices are promising candidates for complementing silicon-based electronics in memory device applications. For example, sputtered thin films of amorphous carbon exhibit memristive behavior. The reported devices, however, have a minimal active area of about 50 nm diameter, leading to large set currents in the µA range. Although power efficiency would benefit from reduced drive currents, resistive switching of amorphous carbon confined to a few cubic nanometers has remained largely unexplored. Here, we investigate resistive switching in 30 nm long and 25 nm wide monolayer arrays of 10 nm gold nanoparticles patterned by direct electron-beam exposure followed by a purpose-designed emulsion-based development process. Electron-beam irradiation transforms the alkanethiol ligands of the gold nanoparticles into a solvent-resistant amorphous carbonaceous matrix allowing pattern development and imparting electronic function. We measure changes in conductivity of up to five orders of magnitude for set currents in the nA range.

Solvent-mediated conductance increase of dodecanethiol-stabilized gold nanoparticle monolayers.

Gold nanoparticle monolayers provide convenient templates to study charge transport in organic molecules beyond single junction techniques. Conductance is reported to increase by several orders of magnitude following immersion of alkanethiol-stabilized gold nanoparticle monolayers in a solution containing conjugated thiol-functionalized molecules. Typically, this observation is attributed to molecular exchange. Less attention has been paid to the role of the solvent alone. Here, we report on an increase in conductance of dodecanethiol-stabilized gold nanoparticle monolayers on Si/SiO2 by an average factor of 36 and 22 after immersion in pure ethanol (EtOH) and tetrahydrofuran (THF), respectively. Analysis by scanning electron microscopy (SEM) and small-angle X-ray scattering (SAXS) reveals a solvent-induced decrease in lattice constant of close-packed monolayers. We compare the conductance of the monolayer after molecular exchange with two different oligophenylenes to shed light on the respective contribution of the solvent-induced structural change and the molecular exchange itself on the conductance increase.

Contact transfer length investigation of a 2D nanoparticle network by scanning probe microscopy.

Nanoparticle network devices find growing application in sensing and electronics. One recurring challenge in the design and fabrication of this class of devices is ensuring a stable interface via robust yet unobstructive electrodes. A figure of merit which dictates the minimum electrode overlap required for optimal charge injection into the network is the contact transfer length. However, we find that traditional contact characterization using the transmission line model, an indirect method which requires extrapolation, is insufficient for network devices. Instead, we apply Kelvin probe force microscopy to characterize the contact resistance by imaging the surface potential with nanometer resolution. We then use scanning probe lithography to directly investigate the contact transfer length. We have determined the transfer length in graphene contacted devices to be 200-400 nm, thus apt for further device reduction which is often necessary for on-site sensing applications. Simulations from a two-dimensional resistor model support our observations and are expected to be an important tool for further optimizing the design of nanoparticle-based devices.

Water-Mediated Assembly of Gold Nanoparticles into Aligned One-Dimensional Superstructures.

This Article shows that water in ethanol colloids of gold nanoparticles enhances the formation of linear clusters and, more important for applications in electronics, determines their assembly on surfaces. We show by dynamic light scattering that ethanol colloids contain mainly monomers and dimers and that wormlike superstructures are mostly absent, despite UV-vis evidence of aggregation. Water added to the colloid as a cosolvent was found to enhance the number of clusters as well as their average size, confirming its role in linear self-assembly, on the scale of a few particles. Water adsorbed from the atmosphere during coating was also found to be a powerful lever to tune self-assembly on surfaces. By varying the relative humidity, a sharp transition from branched to linear superstructures was observed, showing the importance of water as a cosolvent in the formation of cluster superstructures. We show that one-dimensional superstructures may form due to long-range mobility of precursor clusters on wet surfaces, allowing their rearrangement. The understanding of the phenomenon allows us to statistically align both clusters and resulting superstructures on patterned substrates, opening the way to rapid screening in molecular electronics.

Kelvin probe force microscopy for local characterisation of active nanoelectronic devices.

Frequency modulated Kelvin probe force microscopy (FM-KFM) is the method of choice for high resolution measurements of local surface potentials, yet on coarse topographic structures most researchers revert to amplitude modulated lift-mode techniques for better stability. This approach inevitably translates into lower lateral resolution and pronounced capacitive averaging of the locally measured contact potential difference. Furthermore, local changes in the strength of the electrostatic interaction between tip and surface easily lead to topography crosstalk seen in the surface potential. To take full advantage of the superior resolution of FM-KFM while maintaining robust topography feedback and minimal crosstalk, we introduce a novel FM-KFM controller based on a Kalman filter and direct demodulation of sidebands. We discuss the origin of sidebands in FM-KFM irrespective of the cantilever quality factor and how direct sideband demodulation enables robust amplitude modulated topography feedback. Finally, we demonstrate our single-scan FM-KFM technique on an active nanoelectronic device consisting of a 70 nm diameter InAs nanowire contacted by a pair of 120 nm thick electrodes.