Multilayer Super-Translucent Zirconia for Chairside Fabrication of a Monolithic Posterior Crown.

This case report describes the chairside fabrication of a monolithic posterior crown using a multilayer super-translucent zirconia material. According to the manufacturer's information, the newly introduced multilayer zirconia (4-YTZP) offers a unique combination of fracture strength (>850 MPa with speed-sintering) and improved optical properties, thus allowing a reduced minimum material thickness and optional temporary luting. By using up-to-date components of the CEREC system, including superfast dry-milling and a speed-sintering process, the fabrication of a monolithic zirconia crown is possible within an acceptable timeframe for the chairside workflow (60-75 min). The usage of a multilayer super-translucent material allows for the individualization of the restoration, typically in a single combined stain and glaze firing. However, it should be noted that clinical data for this type of restoration are still sparse. Therefore, manufacturer recommendations regarding indication, preparation, and cementation must be followed very strictly.

Prospective clinical evaluation of chairside-fabricated zirconia-reinforced lithium silicate ceramic partial crowns-5-year results.

OBJECTIVES: A university-based randomized clinical study evaluated the 5-year performance of chairside-fabricated zirconia-reinforced lithium silicate (ZLS)-ceramic partial crowns. MATERIAL AND METHODS: Forty-five patients were restored with 61 chairside-fabricated ZLS-restorations (Cerec SW 4.2, Dentsply Sirona, Germany; Vita Suprinity, Vita Zahnfabrik, Germany). Deviating from the manufacturers' recommendations, restorations with reduced minimum material thicknesses (MMT) were fabricated: group 1, MMT = 0.5-0.74 mm (n = 31); group 2, MMT = 0.75-1.0 mm (n = 30). For luting, a self-adhesive cement (SAC) or a total-etch technique with a composite cement (TEC) was applied. Statistical evaluation was performed by time-to-event analysis (Kaplan-Meier). Possible covariates of the survival (SVR) and success rates (SCR), evaluated in a Cox regression model, were MMT, restoration position (premolar/molar), and cementation technique (SAC vs. TEC). RESULTS: Forty patients (54 restorations, premolars, n = 23; molars, n = 31) participated in the 5-year follow-up. Five losses due to ceramic fractures occurred in group 1 (n = 28) (SVR: 83.0% [95% confidence interval (CI): 0.71-0.96]). Group 2 (n = 26) showed no losses (SVR: 100%). The success rate for partial crowns placed on premolars was 100% and 69% (95% CI: 0.54-0.84) for molar restorations. Recementation was required in 4 restorations with SAC (SCR: 86% [95% CI: 0.73-0.99]; SCR-DC: 100%). Restorations in group 2 showed a significantly reduced risk of material fracture hazard ratio (HR) = 0.09, p = 0.0292) compared with the restorations in group 1. Molar partial crowns showed an increased risk for a clinical intervention (HR = 5.26, p = 0.0222) compared to premolar restorations. CONCLUSIONS: Material thickness and position of the restoration are risk factors influencing the survival and success rate of ZLS-ceramic partial crowns. CLINICAL RELEVANCE: Observation of an MMT of at least 0.75-1.0 mm for ZLS-ceramics is essential to avoid material-related fractures. CLINICAL TRIAL REGISTRATION: German Clinical Trails Register (trial number: DRKS00005611).

Surgical treatment of peri-implantitis with or without a deproteinized bovine bone mineral and a native bilayer collagen membrane: A randomized clinical trial.

AIM: To assess whether the use of deproteinized bovine bone mineral (DBBM) and native bilayer collagen membrane (NBCM) improved healing of peri-implantitis-related bone defects at 12 months. MATERIALS AND METHODS: In a multi-centre, randomized clinical trial, 32 individuals received surgical debridement (control group [CG]), and 34 received adjunct use of DBBM and NBCM (test group [TG]). Radiographic defect fill (RDF), probing pocket depth (PPD), bleeding on probing (BOP), suppuration (SUP), recession (REC), cytokines (IL-1ß, IL-1RA, IL-6, IL-8, IL-12, IP10, PDGF-BB, TNF-α, VEGF), and patient-reported outcomes (PROs) were evaluated at 3, 6, 9, and 12 months. RESULTS: RDF at the deepest site amounted 2.7 ± 1.3 mm in TG and 1.4 ± 1.2 mm in CG (p <.0001). PPD was reduced by 1.9 mm in TG and 2.3 mm in CG (p = .5783). There were no significant differences between groups regarding reductions of BOP, SUP, REC, cytokines levels, or oral health impact profile (OHIP)-14 scores at 12 months. Successful treatment (RDF ≥ 1.0 mm, PPD ≤5 mm, ≤1/4 site with BOP grade 1, no SUP) was identified in 32% in TG and 21% in CG. CONCLUSIONS: DBBM and NBCM resulted in significantly more RDF than debridement alone. No difference was found in any clinical parameters or PROs between the groups. ClinicalTrials.gov Identifier: NCT02375750.

Oral Health-Related Quality of Life, Oral Conditions, and Risk of Malnutrition in Older German People in Need of Care-A Cross-Sectional Study.

BACKGROUND: The present cross-sectional study assessed oral health, nutritional condition, and oral health-related quality of life (OHRQoL) in older German people in need of care. METHODS: The participants were recruited from eight nursing homes (including three nursing homes with assisted living) and one mobile nursing service. Oral health, including dental status (decayed, missing and filled teeth (DMF-T), root caries), periodontal treatment needs, and prosthetic conditions, was recorded. Nutritional status was assessed using the screening of the "Mini Nutritional Assessment" (MNA). The OHRQoL was measured using the German short-form of the Oral Health Impact Profile (OHIP-G14) and summarized as a total sum score as well as the four dimensions "oral function", "psychosocial impact", "pain" and "orofacial appearance". STATISTICS: Linear logistic regression analyses. RESULTS: A total of 151 participants (age: 84.17 ± 7.8 years) were included. Most participants (60.3%) were nursing home residents. Nearly half of the individuals (47%) were edentulous and 75.4% of the dentate subjects required periodontal treatment. A total of 115 of the subjects had at least one denture. According to the MNA screening, 107 (70.9%) older people were at risk of malnutrition or already suffered from malnutrition. The median OHIP-G14 sum score was 3 (mean 5.7 ± 7.67). Regression analysis revealed MNA to be influenced by DMF-T, D-T, M-T and OHIP G14 sum score and root caries (pi < 0.01). Within the regression model, missing teeth (ß: -11.9, CI95: -6.4--1.9; p < 0.01) were the strongest influential factor on MNA, followed by DMF-T (ß: 5.1, CI95: 1.7-6.2; p < 0.01). CONCLUSIONS: Older people in nursing settings show a high prevalence of oral diseases, risk of malnutrition and nearly unimpaired OHRQoL. Dental care should be fostered in these individuals, whereby OHRQoL might be a further hint for increased risk of malnutrition.

Risk indicators for mucositis and peri-implantitis: results from a practice-based cross-sectional study.

PURPOSE: This practice-based cross-sectional study aimed to investigate whether common risk indicators for peri-implant diseases were associated with peri-implant mucositis and peri-implantitis in patients undergoing supportive implant therapy (SIT) at least 5 years after implant restoration. METHODS: Patients exclusively restored with a single implant type were included. Probing pocket depth (PPD), bleeding on probing (BOP), suppuration, and radiographic bone loss (RBL) were assessed around implants. The case definitions were as follows: peri-implant mucositis: PPD ≥4 mm, BOP, no RBL; and peri-implantitis: PPD ≥5 mm, BOP, RBL ≥3.5 mm. Possible risk indicators were compared between patients with and without mucositis and peri-implantitis using the Fisher exact test and the Wilcoxon rank-sum test, as well as a multiple logistic regression model for variables showing significance (P<0.05). RESULTS: Eighty-four patients with 169 implants (observational period: 5.8±0.86 years) were included. A patient-based prevalence of 52% for peri-implant mucositis and 18% for peri-implantitis was detected. The presence of 3 or more implants (odds ratio [OR], 4.43; 95 confidence interval [CI], 1.36-15.05; P=0.0136) was significantly associated with an increased risk for mucositis. Smoking was significantly associated with an increased risk for peri-implantitis (OR, 5.89; 95% CI, 1.27-24.58; P=0.0231), while the presence of keratinized mucosa around implants was associated with a lower risk for peri-implantitis (OR, 0.05; 95% CI, 0.01-0.25; P<0.001). CONCLUSIONS: The number of implants should be considered in strategies to prevent mucositis. Furthermore, smoking and the absence of keratinized mucosa were the strongest risk indicators for peri-implantitis in patients undergoing SIT in the present study.

Retrospective evaluation of extended glass-ceramic ceramic laminate veneers after a mean observational period of 10 years.

PURPOSE: A retrospective evaluation of extended anterior ceramic laminate veneers (EACVs) after a mean observational period of 10 years. METHODS: Thirty-one patients (20 females/11 males) underwent restoration with 101 adhesively luted, heat-pressed EACVs (maxilla, n = 65; mandible, n = 36). RESULTS: The 10 year survival rate was 91.8% (95% confidence interval [95%-CI]: 0.87;0.97). Eight ceramic fractures, one biological failure, and one change in treatment plan caused the observed failures. Seventy-seven of the 101 restorations remained intervention-free in service (success rate: 78.6% [95%-CI: 0.70;0.88]). Fourteen interventions were needed (nine recementations, two endodontic treatments, two composite fillings, and one fracture polishing). The jaw position (maxilla/mandible, survival P = .578/success P = .056) had no influence on the clinical performance. EACVs covering large areas of exposed dentin (>50%) were associated with a significantly increased risk (hazard ratio 2.98, P = .019) of needing a clinical intervention (success rate: 68.0% [95%-CI: 0.52; 0.84]). However, the degree of dentin exposure had no effect on the survival rate (P = .761). CONCLUSIONS: After a mean observational period of 10 years, mandibular and maxillary EACVs exhibited survival and success rates that were comparable. Significantly lower success rates were associated with large areas of exposed dentin (>50%). CLINICAL SIGNIFICANCE: Mandibular and maxillary EACV revealed 10-year survival rates comparable to those published for anterior metal-ceramic and glass-ceramic full-coverage crowns. Precaution should be taken not to expose dentin, and when large areas of dentin are exposed, different conditioning/luting strategies should be used.

Comprehensive assessment of dental behaviour and oral status in patients with tongue piercing-results of a cross-sectional study.

OBJECTIVES: Aim of this cross-sectional case-control study was the comprehensive examination of oral health, oral behaviour and oral health-related quality of life of patients with tongue piercing. Furthermore, different piercing related factors and the presence of habits should be considered regarding their potential association to piercing-related complications. MATERIAL AND METHODS: Participants with tongue piercing (n = 50) and a matched control (n = 50) were included. Dental examination included decayed-, missing- and filled-teeth-index (DMF-T) and the presence of non-carious tooth defects. Periodontal examination contained of periodontal probing depth (PPD), bleeding on probing (BOP) and recession. Piercing-related factors, oral behaviour as well as oral health-related quality of life [German short form of oral health impact profile (OHIP G14)] were assessed based on questionnaires. STATISTICS: Man-Whitney U test, chi-square and Fisher's exact test (significance level p < 0.05). RESULTS: Participants with tongue piercing suffered from worse DMF-T, PPD, BOP and recession (pi < 0.01). Higher prevalence of enamel cracks and trough-shaped abrasions were found in piercing-group (pi < 0.01). Additionally, participants with tongue piercing showed worse oral behaviour, insufficient cleaning of piercing and in majority of cases (80%) calculus formation at piercing surface as well as comparable OHIP-G14 to control (p = 0.39). While piercing design was associated to both, recession and non-carious tooth defects (pi < 0.05), only infractures of enamel were associated to the presence habits (p = 0.04). CONCLUSIONS: Patients with tongue piercing show insufficient dental and periodontal health as well as reduced oral behaviour. Thereby, piercing design and wearing period is associated to recessions and non-carious tooth defects. CLINICAL RELEVANCE: Increased attention of patients wearing tongue piercing in dental practice is necessary.

Clinical evaluation of chairside-fabricated partial crowns composed of zirconia-reinforced lithium silicate ceramics: 3-year results of a prospective practice-based study.

OBJECTIVES: Prospective practice-based clinical evaluation of chairside fabricated monolithic partial crowns composed of zirconia-containing lithium silicate (ZLS) ceramic material. MATERIALS AND METHODS: Between October 2013 and September 2014, 71 patients were restored with 92 partial crowns on vital or sufficiently endodontically treated teeth. The monolithic restorations were fabricated chairside (Cerec SW 4.2/Cerec MC XL) from a glaze-fired ZLS ceramic material (Celtra Duo, Dentsply Sirona, Bensheim, Germany). Adhesive cementation was performed using the total-etch technique with one of two dual-curing composite materials. Modified United States Public Health Service parameters were evaluated annually; moreover, the parameters "time-dependent survival" (in situ criterion) and "success rates" (event-free restorations) were evaluated according to Kaplan-Meier analysis. RESULTS: Sixty-nine patients with 17 premolar and 71 molar partial crowns attended annual follow-up examinations (observational period: 36.0 ± 5.7 months). Two complete failures were recorded and were caused by a tooth fracture (at 30 months) and a restoration fracture (at 38 months), (3-year survival rate: 99%; 95% confidence interval (CI 95%): [0.97;1]). One clinical intervention was necessary (endodontic treatment) to maintain function (3-year success rate: 98%; (CI95%: [0.95:1]). CONCLUSIONS: Chairside-fabricated ZLS partial crowns show a good initial clinical performance. However, to further evaluate this new material, clinical data from studies with longer observational periods are required. CLINICAL SIGNIFICANCE: Based on this mid-term evaluation, ZLS ceramics appear to be a promising alternative material for the chairside fabrication of adhesively luted monolithic posterior restorations with a low risk of material-related complications.

Prevalence of periodontal pathogenic bacteria at different oral sites of patients with tongue piercing - results of a cross sectional study.

Aim of this cross-sectional study was to investigate the prevalence of selected potentially periodontal pathogenic bacteria in different sites of patients with tongue piercing (TP) in comparison to a control group (C). Fifty participants in each group were recruited. Samples from the biofilm originating from the piercing surface (TP group), periodontal pocket, tongue as well as cheek surface were examined regarding presence of 11 selected potentially periodontal pathogenic bacteria based on polymerase-chain reaction (PCR). In the periodontal pocket of the participants, the majority of examined bacteria were more frequently detected in TP compared to C group (pi < 0.05). At tongue and cheek surface, the prevalence of Treponema denticola (P < 0.01) and Prevotella intermedia (P < 0.01) was significantly higher in TP. For the majority of bacteria, a significant correlation between TP surface and periodontal pocket was detected (P < 0.05). In conclusion TP must be considered as potentially important ecological niche and reservoir for periodontal pathogens.

Diabetes Screening in Dental Practice Using the Find-Risk Questionnaire - A Practice-based Pilot Study.

PURPOSE: This dental practice-based pilot study aimed to investigate the efficacy of diabetes mellitus (DM) screening based on questionnaire replies. MATERIALS AND METHODS: 116 patients were screened in a private dental practice when visiting the dentist for a regular check-up. The Find-Risk (FR) questionnaire was used for diabetes screening. FR-positive (FR+) patients were referred to a diabetologist for further diagnostics (blood glucose, HbA1c); FR-negative patients (FR-) did not receive a diabetological examination. Furthermore, dental findings (DMFT) were obtained and periodontal condition was classified into no, mild, moderate or severe periodontitis, based upon periodontal pocket depth and clinical attachment loss. Sensitivity and specificity of the FR questionnaire and a modified FR questionnaire (additional inquiry if severe periodontitis had been ever diagnosed) were determined in a statistical model. RESULTS: 102 patients with a mean age of 56.31 years were included. Seven patients had known DM. A total of 36 patients were FR+, including the seven patients with known DM. Only 16 of the 29 participants (55%) followed the recommendation to see the diabetologist. Nine of these 16 patients showed conspicuous blood glucose findings. Both with and without modification of the FR questionnaire, a sensitivity of 100% was achieved. With the modified FR questionnaire, a higher specificity was shown in a statistical model compared to the FR questionnaire without modification (80% vs 69.5%). CONCLUSION: FR-based DM screening in dental practice is possible and could help to identify patients with (pre-) diabetes. However, these results must be validated in a large patient cohort.

Overdentures borne on less than four abutments with telescopic crowns: 5-year results of a retrospective clinical study.

OBJECTIVE: Retrospective evaluation of the clinical performance of tooth-supported overdentures retained by resilient telescopic crowns with occlusal clearance fit (ODRTC) in severely reduced dentition (1-3 remaining teeth). MATERIALS AND METHODS: A total of 313 ODRTCs were inserted in an undergraduate prosthodontic program (University Medical Center, Goettingen, Germany) between 2000 und 2012. Data regarding 263 ODRTCs in 221 patients were reevaluated (observational period: 64.5 ± 34.8 months), and time-dependent survival and success rates (Kaplan-Meier-Estimator) were calculated. The number of the abutment teeth was analyzed as an influencing factor (Cox regression model (p < 0.05)). RESULTS: The 5- and 8-year overdenture survival rates were 62% [CI: 0.55; 0.69] and 38% [CI: 0.30; 0.45]. The 5- and 8-year success-rates (biologically and technically event-free restorations) were 13% [CI: 0.09; 0.17] and 3% [CI: 0.01; 0.05]. On the abutment level, the 5- and 8-year survival rates were 55% [CI: 0.48; 0.62], and 34% [CI: 0.27; 0.42]. The number of abutment teeth significantly influenced the overdenture and abutment survival rates. Restorations with 1 or 2 abutments were significantly associated with an increased number of technical and biological complications (decementation of the primary crown, abutment fracture) compared to ODRTCs with 3 abutments. CONCLUSIONS: The survival and success rates of ODRTCs are significantly influenced by the number of abutments. CLINICAL RELEVANCE: For ODRTCs, reduced survival and success rates are expected, especially when only 1 or 2 abutment teeth are included.

Association of chairside salivary aMMP-8 findings with periodontal risk assessment parameters in patients receiving supportive periodontal therapy.

PURPOSE: The aim of this retrospective cross-sectional study was to evaluate whether salivary findings of active matrix-metalloproteinase 8 (aMMP-8) chairside (point of care; POC) tests were associated with periodontal risk assessment parameters in patients receiving supportive periodontal therapy (SPT). METHODS: A total of 125 patients receiving regular SPT were included, and their records were examined. The following inclusion criteria were used: a diagnosis of chronic periodontitis, at least 1 non-surgical periodontal treatment (scaling and root planning) with following regular SPT (minimum once a year), at least 6 remaining teeth, and clinical and aMMP-8 findings that were obtained at the same appointment. In addition to anamnestic factors (e.g., smoking and diabetes), oral hygiene indices (modified sulcus bleeding index [mSBI] and approximal plaque index), periodontal probing depth simultaneously with bleeding on probing, and dental findings (number of decayed, missing, and filled teeth) were recorded. Salivary aMMP-8 levels were tested using a commercial POC test system (Periomarker, Hager & Werken, Duisburg, Germany). Statistical analysis was performed using the t-test, Mann-Whitney U test, Fisher's exact test, and χ2 test, as appropriate (P<0.05). RESULTS: Only the mSBI was significantly associated with positive salivary aMMP-8 findings (aMMP-8 positive: 27.8%±20.9% vs. aMMP-8 negative: 18.0%±14.5%; P=0.017). No significant associations were found between aMMP-8 and smoking, diabetes, periodontal parameters, or parameters related to the maintenance interval (P>0.05). CONCLUSIONS: Salivary aMMP-8 chairside findings were not associated with common parameters used for periodontal risk assessment in patients receiving SPT. The diagnostic benefit of POC salivary aMMP-8 testing in risk assessment and maintenance interval adjustment during SPT remains unclear.

Removal forces of adhesively and self-adhesively luted implant-supported zirconia copings depend on abutment geometry.

This in vitro study evaluated the effects of different abutment axial heights on the retentiveness of adhesively and self-adhesively luted zirconia copings. Ankylos implants were embedded in resin blocks. Two groups of titanium abutments ("long", height: 6.79 mm, taper: 4.8°; "short", height: 4.31 mm, taper: 4.8°; Compartis-ISUS, DeguDent) were used for the luting of CAD/CAM-fabricated zirconia copings (Compartis, DeguDent) with an adhesive (Multilink Automix; Ivoclar Vivadent) and a self-adhesive (RelyX Unicem; 3M ESPE) composite. After water storage and 5000 thermocycles (5 °C/55 °C), retention forces were evaluated using a universal testing machine (Zwick). Significant differences were determined via two-way ANOVA and t-tests with Bonferroni-Holm correction. Significant interactions between abutment geometry and luting agents were observed. RelyX Unicem showed the highest levels of retentiveness, irrespective of the varying abutment geometries (mean values long/short: 487.7 N/447.9 N). When Multilink Automix was used, removal forces were significantly lower (311.7 N/101.1 N) and negatively affected by the use of the shorter abutments. Customized long abutments supported better retention forces than customized short abutments for both luting agents.

Influence of Material Selection on the Marginal Accuracy of CAD/CAM-Fabricated Metal- and All-Ceramic Single Crown Copings.

This study evaluated the marginal accuracy of CAD/CAM-fabricated crown copings from four different materials within the same processing route. Twenty stone replicas of a metallic master die (prepared upper premolar) were scanned and divided into two groups. Group 1 (n = 10) was used for a pilot test to determine the design parameters for best marginal accuracy. Group 2 (n = 10) was used to fabricate 10 specimens from the following materials with one identical CAD/CAM system (GAMMA 202, Wissner GmbH, Goettingen, Germany): A = commercially pure (cp) titanium, B = cobalt-chromium alloy, C = yttria-stabilized zirconia (YSZ), and D = leucite-reinforced glass-ceramics. Copings from group 2 were evaluated for the mean marginal gap size (MeanMG) and average maximum marginal gap size (AMaxMG) with a light microscope in the "as-machined" state. The effect of the material on the marginal accuracy was analyzed by multiple pairwise comparisons (Mann-Whitney, U-test, α = 0.05, adjusted by Bonferroni-Holmes method). MeanMG values were as follows: A: 46.92 ± 23.12 µm, B: 48.37 ± 29.72 µm, C: 68.25 ± 28.54 µm, and D: 58.73 ± 21.15 µm. The differences in the MeanMG values proved to be significant for groups A/C (p = 0.0024), A/D (p = 0.008), and B/C (p = 0.0332). AMaxMG values (A: 91.54 ± 23.39 µm, B: 96.86 ± 24.19 µm, C: 120.66 ± 32.75 µm, and D: 100.22 ± 10.83 µm) revealed no significant differences. The material had a significant impact on the marginal accuracy of CAD/CAM-fabricated copings.

Retrospective evaluation of extended heat-pressed ceramic veneers after a mean observational period of 7 years.

OBJECTIVES: Retrospective evaluation of extended anterior glass-ceramic veneers 7 years after placement in a private practice. MATERIALS AND METHODS: A total of 31 patients (20 females/11 males) underwent restoration with adhesively luted extended veneers that were fabricated using heat-pressed glass-ceramic (Cergo, Dentsply Sirona). A single dentist restored 101 teeth (maxilla, n = 65; mandible, n = 36). Adhesive cementation was performed using an etch-and-rinse adhesive (OptibondFL, Kerr Corporation), and two different dual-curing composite cements (Variolink, Ivoclar Vivadent/Calibra, Dentsply Sirona). RESULTS: After 7 years, the Kaplan-Meier survival rate (in situ criteria) was 93.6% (95% CI: 0.89; 0.98). The observed failures were caused by ceramic fractures for seven restorations and biological failure for one restoration. In total 80 of the 101 restorations were still in service and did not require any clinical intervention (7-year success rate: 84.3% [95% CI]: 0.76; 0.93). Interventions were necessary in 13 cases (8 recementations, 2 endodontic treatments, 2 composite fillings (caries), and 1 polishing of minor fractures). The clinical performance was not influenced by the veneer position (maxilla/mandible, survival P = .56/success P = .30). The veneers that covered large areas of exposed dentin (>50%) exhibited a significantly increased risk (hazard ratio 3.71, P = .0041) for requiring a clinical intervention; however, no effect on the survival rate was observed for these veneers (P = .35). CONCLUSIONS: Following 7 years of clinical service, extended anterior ceramic veneer restorations exhibited comparable survival and success rates for the upper and lower jaw. Large areas of exposed dentin (>50%) were associated with significantly lower success rates. CLINICAL SIGNIFICANCE: Dentin exposure (more than 50% of the preparation surface) during preparation significantly affects the clinical performance of extended heat-pressed glass-ceramic veneers.

Prospective Evaluation of Posterior Fixed Zirconia Dental Prostheses: 10-Year Clinical Results.

PURPOSE: To investigate the clinical survival and success rates of conventionally luted three- and four-unit fixed dental prostheses (FDPs) with zirconia frameworks (Cercon Smart Ceramics, DeguDent) after a mean observation period of 119 ± 36 months. MATERIALS AND METHODS: A total of 75 patients were treated in the Department of Prosthodontics at the University of Goettingen, Germany, and a total of 99 posterior FDPs were inserted and luted with zinc phosphate cement. Time-dependent survival and success rates were calculated using Kaplan-Meier curves, and their relationships with the type of veneer (ceramic), location (maxilla vs mandible), and span length (three-unit vs four-unit) were analyzed with a Cox regression model (P < .05). RESULTS: Of the 99 inserted FDPs, 24 were lost to follow-up, 51 remained functional and passed the 10-year examination (overall survival rate: 75.0%; 95% confidence interval [CI]: 0.64, 0.85), and 13 were absolute failures caused by technical events (technical survival rate: 84%; 95% CI: 0.64, 0.85). In 50 FDPs, relative failure required a clinical intervention to maintain function (overall success rate: 40%; 95% CI: 0.29, 0.52). For 35 of these FDPs, the relative failure was caused by technical events (technical success rate: 61%; 95% CI: 0.49, 0.73). None of the evaluated factors showed an association with overall or technical survival or success. CONCLUSION: Zirconia-based posterior FDPs produced with a first-generation computer-assisted manufacturing (CAM) system revealed high rates of absolute and relative failure, mainly due to technical events, after a mean observational period of 10 years. Further clinical studies with updated computer-assisted design (CAD)/CAM systems are needed to determine the long-term performance of zirconia-based FDPs.

No difference between manual and different power toothbrushes with and without specific instructions in young, oral healthy adults-results of a randomized clinical trial.

BACKGROUND: The aim of this randomized clinical study was to detect the effect of an instruction within a group using oscillating-rotating (OR), sonic-active (SA), or manual toothbrushes (MTB) in young, oral healthy adults. METHODS: One hundred fifty participants were randomly assigned into six groups (n = 25): with (OR-I, SA-I, MTB-I) and without instruction (OR-NI, SA-NI, MTB-NI). Participants in I subgroups received one standardized instruction of the toothbrush system. At baseline (t0), after 2 (t1), 4 (t2), and 12 weeks (t3), plaque indices including modified Quigley-Hein Index (QHI) and Marginal Plaque Index (MPI) as well as inflammation indices including Papilla Bleeding Index (PBI) and Gingival Index (GI) were assessed. Kruskal-Wallis test, Friedman test, and chi-square or Fisher's exact test (p < 0.05) were used for statistical analysis. RESULTS: One hundred thirty-one participants completed the follow-up and were analyzed: OR-I = 21, OR-NI = 22, SA-I = 22, SA-NI = 22, MTB-I = 22, and MTB-NI = 22. Within groups between t0 and t3, OR and SA systems showed a significant plaque reduction, irrespective of instruction (p i < 0.05). In MTB-I and in SA-NI subgroups, a reduction of GI was detected, while an improvement in PBI within SA-I was found (p i < 0.05). Thereby, after 12 weeks, gingival inflammation and plaque indices were comparable between all subgroups (p i > 0.05). Irrespective of the toothbrush system used, only QHI was positively influenced by instruction (p < 0.01). CONCLUSION: The used toothbrush as well as the presence or absence of a single brush-specific instruction has no influence on plaque removal and reduction of gingival inflammation in young, oral healthy adults in an observation period of 12 weeks. CLINICAL RELEVANCE: A single instruction might bring no benefit in this patient group, independently of the used toothbrush system.

Correction to: No difference between manual and different power toothbrushes with and without specific instructions in young, oral healthy adults-results of a randomized clinical trial.

The type of used rotating-oscillating toothbrush was incorrectly assigned; correct used rotating-oscillating toothbrush is Pro1000 Precision Clean, Procter&Gamble GmbH, Schwalbach, Germany.

Comparison of different maintenance strategies within supportive implant therapy for prevention of peri-implant inflammation during the first year after implant restoration. A randomized, dental hygiene practice-based multicenter study.

PURPOSE: This randomized clinical multicenter study compared different professional preventive approaches on peri-implant inflammation under supportive implant therapy (SIT). METHODS: 105 participants (167 implants) were randomly allocated to four groups. All participants were under SIT with a 3-month recall interval. Plaque removal was performed by using manual curettes, a sonic-driven scaler, and a prophylaxis brush (Group A), supplemented by chlorhexidine (CHX) varnish on the implant surfaces (Group C) or by using manual curettes, air polishing with glycine powder, and a prophylaxis brush (Group B), supplemented by treatment with CHX varnish on the implant surfaces (Group D). The peri-implant probing depths (PPD), mucosal recession (MR), and bleeding on probing (BOP) on implants were determined at baseline. After 12 months, the final PPD, MR, and BOP on implants were assessed. The statistical evaluation consisted of Kruskal-Wallis-test, Wilcoxon-test and Chi-squared test modified according to McNemar (P< 0.05). RESULTS: 62 subjects (n= 101 implants) were available for assessment. In Groups A, C, and D, no significant implant-related differences between baseline and follow-up were found in PPD, MR, and BOP. Group B showed a significant difference (P= 0.022) between baseline (1.77 ± 1.58 mm) and follow-up (2.31 ± 1.54 mm) in PPD. The location of implant (P= 0.02), the type of implant (P= 0.01), and the age of subject (P= 0.04) had significant influences on BOP. CLINICAL SIGNIFICANCE: All strategies were effective in preventing peri-implant inflammation. The supplemental application of chlorhexidine varnish had no significant additional benefit.

Influence of manual and power toothbrushes on clinical and microbiological findings in initial treatment of periodontitis - A randomized clinical study.

PURPOSE: This randomized clinical study compared the influence of manual and power toothbrushes on clinical and microbiological findings in initial treatment of periodontitis. METHODS: A total of 72 participants with a mean age of 55.7 years were randomly assigned to three groups (n= 24):oscillating-rotating (OR), sonic-active (SA) and manual toothbrush (MTB). At baseline, after 4 weeks and after 12 weeks, the following parameters were assessed:modified Quigley-Hein-Index (QHI), papilla bleeding index (PBI), periodontal pocket depth (PPD), bleeding on probing (BOP) and recession. For microbiological analysis (PCR) of 11 periodontal pathogenic bacteria, samples of sulcular fluid were taken from the deepest pockets. Statistical analysis was performed using ANOVA, with the level of significance set at α= 5%. RESULTS: All clinical parameters:PBI, modified QHI, PPD, BOP and recession showed an improvement after 12 weeks compared to baseline, regardless of which toothbrush system was used. Regarding PBI, the SA group showed significantly greater improvement compared to OR and MTB (P< 0.01). In plaque removal (QHI) only OR was significantly more effective than MTB (P= 0.01). Periodontal parameters showed a significantly higher reduction of PPD for SA compared to MTB and MTB compared to OR (Plt; 0.05), while for BOP only a significantly higher reduction in SA compared to OR was detected (P= 0.01) Microbiological analysis showed an improvement in prevalence of several bacteria without significant differences between groups. CLINICAL SIGNIFICANCE: Patients might benefit from powered TB systems, especially in initial treatment of periodontitis.