Evaluation of Membrane Integrity Monitoring Methods for Hollow Fiber Nanofiltration Membranes: Applicability in Gray Water Reclamation Systems.

Source-separated gray water reclamation using nanofiltration as an advanced post-treatment option has received substantial interest in meeting the growing water demand. During reclamation, membrane integrity is crucial to ensure the water's safety. This study evaluated several chemical and novel microbial indicators as indirect membrane integrity-monitoring methods for hollow fiber nanofiltration membranes in reclamation schemes. Under normal conditions, high retention of divalent ions and organic matter and near-complete removal of Escherichia coli (E. coli) were observed. Limited removal of the antibiotic gene (ARG) tetO was observed due to low feed concentrations and a higher detection limit (LOD). While 16S rRNA and ARG sul1 were not limited by their LODs, lower removals were observed, most likely due to free-floating DNA passing through the membranes. A broken fiber in a pilot-scale module reduced organic matter and microorganism removal substantially, while flux and ion rejection remained similar. Predictions made using the observed results and a previously proposed model allowed for the evaluation of the selected methods in upscaled reclamation systems. Based on these results, it was concluded that microorganisms could be employed as indicators in indirect membrane integrity-monitoring methods in large-scale reclamation schemes, while UV254nm absorbance (used in organic matter determination) could be a viable solution in pilot-scale systems.

Incorporation of an Intermediate Polyelectrolyte Layer for Improved Interfacial Polymerization on PAI Hollow Fiber Membranes.

In a single-step spinning process, we create a thin-walled, robust hollow fiber support made of Torlon® polyamide-imide featuring an intermediate polyethyleneimine (PEI) lumen layer to facilitate the integration and covalent attachment of a dense selective layer. Subsequently, interfacial polymerization of m-phenylenediamine and trimesoyl chloride forms a dense selective polyamide (PA) layer on the inside of the hollow fiber. The resulting thin-film composite hollow fiber membranes show high NaCl rejections of around 96% with a pure water permeability of 1.2 LMH/bar. The high success rate of fabricating the thin-film composite hollow fiber membrane proves our hypothesis of a supporting effect of the intermediate PEI layer on separation layer formation. This work marks a step towards the development of a robust method for the large-scale manufacturing of thin-film composite hollow fiber membranes for reverse osmosis and nanofiltration.

Quantification of the Retention and Disassembly of Virus Particles by a PEI-Functionalized Microfiltration Membrane.

Monitoring the performance of polymer-functionalized surfaces that aim at removing and inactivating viruses is typically labor-intensive and time-consuming. This hampers the development and optimization of such surfaces. Here we present experiments of low complexity that can be used to characterize and quantify the antiviral properties of polymer-functionalized surfaces. We showcase our approach on polyethylenimine (PEI)-coated poly(ether sulfone) (PES) microfiltration membranes. We use a fluorescently labeled model virus to quantify both virus removal and inactivation. We directly quantify the log removal of intact viruses by this membrane using single particle counting. Additionally, we exploit the change in photophysical properties upon disassembly of the virus to show that viruses are inactivated by the PEI coating. Although only a small fraction of intact viruses can pass the membrane, a considerable fraction of inactivated, disassembled viruses are found in the filtrate. Fluorescence microscopy experiments show that most of the viruses left behind on the microfiltration membrane are in the inactivated, disassembled state. Combined, our fluorescence microscopy and spectroscopy experiments show that not only does the model virus adsorb to the PEI coating on the membrane but also the interaction with PEI results in the disassembly of the virus capsid.

Optimizing fluorophore density for single virus counting: a photophysical approach.

In health and environmental research, it is often necessary to quantify the concentrations of single (bio) nanoparticles present at very low concentrations. Suitable quantification approaches that rely on counting and tracking of single fluorescently labelled (bio) nanoparticles are often challenging since fluorophore self-quenching limits the maximum particle brightness. Here we study how the number of labels per nanoparticle influences the total brightness of fluorescently labelled cowpea chlorotic mottle virus (CCMV). We analyze in detail the photophysical interplay between the fluorophores on the virus particles. We deduce that the formation of dark aggregates and energy transfer towards these aggregates limits the total particle brightness that can be achieved. We show that by carefully selecting the number of fluorescent labels per CCMV, and thus minimizing the negative effects on particle brightness, it is possible to quantify fluorescently labelled CCMV concentrations down to fM concentrations in single particle counting experiments.

Aquaporin-Containing Proteopolymersomes in Polyelectrolyte Multilayer Membranes.

The field of membranes saw huge developments in the last decades with the introduction of both polyelectrolyte multilayer (PEM)-based membranes and biomimetic membranes. In this work, we combine these two promising systems and demonstrate that proteopolymersomes (PP+) with the incorporated aquaporin protein can be distributed in a controlled fashion using PEMs, even on the inner surface of a hollow fiber membrane. In this way, various proteopolymersome multilayers (PPMs) are fabricated using PP+ as the positively charged species in combination with the polyanions poly(styrene 4-sulfonate) (PSS) and poly(acrylic acid) (PAA). It is shown by reflectometry through alternately adsorbing the polyanions and PP+ that, for both PAA and PSS, a good layer growth is possible. However, when the multilayers are imaged by SEM, the PAA-based PPMs show dewetting, whereas vesicular structures can only be clearly observed in and on the PSS-based PPMs. In addition, membrane permeability decreases upon coating the PPMs to 2.6 L∙m-2∙h-1∙bar-1 for PAA/PP+ and 7.7 L∙m-2∙h-1∙bar-1 for PSS/PP+. Salt retentions show that PAA/PP+ layers are defective (salt retentions <10% and high molecular weight cut-off (MWCO)), in line with the observed dewetting behavior, while PPMs based on PSS show 80% MgSO4 retention in combination with a low MWCO. The PSS/PP+ membranes show a Donnan-exclusion behavior with moderate MgCl2 retention (50%-55%) and high Na2SO4 retention (85%-90%) indicating a high amount of negative charge present within the PPMs. The corresponding PEMs, on the other hand, are predominately positively charged with MgCl2 retention of 97%-98% and Na2SO4 retention of 57%-80%. This means that the charge inside the multilayer and, thus, its separation behavior can be changed when PP+ is used instead of a polycation. When comparing the PPM membranes to the literature, similar performances are observed with other biomimetic membranes that are not based on interfacial polymerization, but these are the only ones prepared using a desired hollow fiber geometry. Combining PEMs and biomimetic approaches can, thus, lead to relevant membranes, especially adding to the versatility of both systems.

Nafion-Based Low-Hydration Polyelectrolyte Multilayer Membranes for Enhanced Water Purification.

The increase of micropollutant concentration in both surface and groundwater is an emerging concern for the environment and human health. Most of such small organic molecules (medicines, hormones, and plasticizers) enter the environment via our wastewater, because they are not sufficiently removed by the current techniques applied in wastewater treatment plants. A possible solution to remove micropollutants is the usage of polyelectrolyte multilayer (PEM) based membranes. PEM membranes have received a growing interest in the past decade due to their high chemical and physical stability and their high permeability and selectivity. A popular polyelectrolyte pair to make dense PEM membranes with high salt retentions is the combination of poly(allylamine hydrochloride) (PAH) and poly(sodium 4-styrenesulfonate) (PSS). Unfortunately, smaller micropollutants (such as bisphenol A, sulfamethoxazole, naproxen, and bezafibrate) still show significant permeation through this membrane. In this study, for the first time, a single final layer of Nafion is applied on the PEM to increase the density of the PEM membrane. It is shown that when terminating with Nafion, the swelling of the multilayer decreases by 50%. These pronounced changes in layer structure are reflected by changes in membrane performance, such as a lower molecular weight cutoff (MWCO) and an increasing hydraulic membrane resistance. Furthermore, we show that the Nafion content of the multilayer can be increased by constructing a Nafion/PAH multilayer on top of the existing PSS/PAH multilayer, thereby lowering the MWCO. Although hydraulic resistance increases, these PSS/PAH/Nafion-based multilayers show excellent performance in rejecting difficult-to-remove micropollutants that have low molecular weight (200-650 Da) and different charges. Overall, a cocktail of eight small micropollutants can be removed up to 97% by these membranes, allowing strongly enhanced water purification.