Design and evaluation of in situ gel eye drops containing nanoparticles of Gemifloxacin Mesylate.

Traditional eye drops used for topically administering drugs have poor ocular bioavailability due to the biological barriers of the eye. There is an interest to design and develop novel drug delivery systems that would extend the precorneal residence time, reduce the frequency of administration and decrease dose-related toxicity. This study aimed to prepare Nanoparticles of Gemifloxacin Mesylate and incorporate them into an in situ gel. The nanoparticles were prepared by ionic gelation technique, using 32 factorial design. Sodium tripolyphosphate (STPP) was used to crosslink Chitosan. The optimized formulation of the nanoparticles (GF4) contained 0.15% Gemifloxacin Mesylate, 0.15% Chitosan and 0.20% STPP, producing 71 nm particle size and 81.11% entrapment efficiency. The prepared nanoparticles showed biphasic release, with an initial burst release of 15% in 1.0 hr and a cumulative drug release of 90.53% at the end of 24 hrs. After that, the prepared nanoparticles were incorporated into an in situ gel, using Poloxamer 407, producing a sustained drug release with efficient antimicrobial activity against gram-positive and gram-negative bacteria as confirmed by the cup plate method.

Development of Valsartan Floating Matrix Tablets Using Low Density Polypropylene Foam Powder: In vitro and In vivo Evaluation.

The main purpose of the study was to develop valsartan floating tablets (VFT) via non-effervescent technique using low density polypropylene foam powder, carbopol, and xanthan gum by direct compression. Before compression, the particulate powdered mixture was evaluated for pre-compression parameters. The prepared valsartan tablets were evaluated for post-compression parameters, swelling index, floating lag time, in vitro buoyancy studies, and in vitro and in vivo X-ray imaging studies in albino rabbits. The result of all formulations for pre- and post-compression parameters were within the limits of USP. FTIR and DSC studies revealed no interaction between the drug and polymers used. The prepared floating tablets had good swelling and floating capabilities for more than 12 h with zero floating lag time. The release of valsartan from optimized formulation NF-2 showed sustained release up to 12 h; which was found to be non-Fickian release. Moreover, the X-ray imaging of optimized formulation (NF-2) revealed that tablet was constantly floating in the stomach region of the rabbit, thereby indicating improved gastric retention time for more than 12 h. Consequently, all the findings and outcomes have showed that developed valsartan matrix tablets could be effectively used for floating drug delivery system.

Dual coated erodible microcapsules for modified release of diclofenac sodium.

Diclofenac sodium was formulated as novel enteric microcapsules for improved delivery to the intestine using the polymers cellulose acetate phthalate (CAP) and ethyl cellulose (EC). The enteric coating was given using an innovative technique combining the wet granulation and thermal change methods. The novel process was analysed for its capability to produce microcapsules of uniform size, good flowability, uniform drug loading and maximum entrapment efficacy and the absence of interaction between drug and process parameters as well as the polymers. In vitro release study was carried out in simulated gastric fluid (SGF) for first 2 h and simulated intestinal fluid (SIF) for next 6 h. The best formulation that contained cellulose acetate phthalate and ethyl cellulose in the concentration of 10:90 at 1:1.5 drug-polymer ratio (B3) was further evaluated using in vivo for its pharmacodynamic efficacy and ulcerogenicity. In addition to sustained and uniform release of drug, the formulation B3 showed better anti-inflammatory activity than the marketed formulation and retarded drug release in the gastric medium. The biological examination of incised stomach showed no histological alterations in term of mucous surface cells and glands.

Design and evaluation of matrix diffusion controlled transdermal patches of verapamil hydrochloride.

Transdermal patches of verapamil hydrochloride were prepared using four different polymers (individual and combination): Eudragit RL100 (ERL100), Eudragit RS100 (ERS100), hydroxypropyl methylcellulose 15 cps (HPMC), and ethyl cellulose (EC), of varying degrees of hydrophilicity and hydrophobicity. The effect of the polymers on the technological properties, i.e., drug release, water vapor transmission rate (WVTR), and percentage moisture loss (ML), percentage moisture absorption (MA), folding endurance, and thickness, was investigated. Different formulations were prepared in accordance with the 2(3) factorial design, with ERL100 being the parent polymer. The patch containing ERL100 alone showed maximum WVTR, % MA, and % ML, which could be attributed to its hydrophilic nature. As expected, substitution with ERS100, HPMC, and EC decreased all the above values in accordance with their decreasing degree of hydrophilicity. In vitro release studies showed zero-order release of the drug from all the patches, and the mechanism of release was diffusion mediated. Moreover, the release of the drug was sustained and it extended over a period of 24 hr in all formulations. A12 emerged as the most satisfactory formulation insofar as its technological properties were concerned. Further, release and permeation of the drug from the most satisfactory formulation (A12) was evaluated through different biological barriers (shed snake skin, rabbit skin, and rat skin) to get an idea of the drug permeation through human skin. Shed snake's skin was found to be most permeable (82.56% drug release at 24 hr) and rat skin was least permeable (52.38%). Percutaneous absorption studies were carried out in rabbits. The pharmacokinetic parameters calculated from blood levels of the drug revealed a profile typical of a sustained release formulation, with the ability to maintain adequate plasma levels for 24 hr. [AUC: 3.09 mg/mL hr, Cmax: 203.95 microg/mL, Tmax: 8 hr]. It can therefore be concluded that the patch containing ERL100 and HPMC in the ratio 8:2 has achieved the objectives of transdermal drug delivery system, such as avoidance of first pass effect, extended release, and reduced frequency of administration.