Kinetics of enol formation from reaction of OH with propene.

Kinetics of enol generation from propene has been predicted in an effort to understand the presence of enols in flames. A potential energy surface for reaction of OH with propene was computed by CCSD(T)/cc-pVDZ//B3LYP/cc-pVTZ calculations. Rate constants of different product channels and branching ratios were then calculated using the Master Equation formulation (J. Phys. Chem. A 2006, 110, 10528). Of the two enol products, ethenol is dominant over propenol, and its pathway is also the dominant pathway for the OH + propene addition reactions to form bimolecular products. In the temperature range considered, hydrogen abstraction dominated propene + OH consumption by a branching ratio of more than 90%. Calculated rate constants of enol formation were included in the Utah Surrogate Mechanism to model the enol profile in a cyclohexane premixed flame. The extended model shows consistency with experimental data and gives 5% contribution of ethenol formation from OH + propene reaction, the rest coming from ethene + OH.

Pollutant emissions from gasoline combustion. 1. Dependence on fuel structural functionalities.

To study the formation of air pollutants and soot precursors (e.g., acetylene, 1,3-butadiene, benzene, and higher aromatics) from aliphatic and aromatic fractions of gasoline fuels, the Utah Surrogate Mechanisms is extended to include submechanisms of gasoline surrogate compounds using a set of mechanism generation techniques. The mechanism yields very good predictions of species concentrations in premixed flames of n-heptane, isooctane, benzene, cyclohexane, olefins, oxygenates, and gasoline using a 23-component surrogate formulation. The 1,3-butadiene emission comes mainly from minor fuel fractions of olefins and cyclohexane. The benzene formation potential of gasoline components shows the following trends as functions of (i) chemical class: n-paraffins < isoparaffins < olefins < naphthalenes < alkylbenzenes < cycloparaffins < toluene; (ii) carbon number: n-butane < n-pentane < n-hexane; and (iii) branching: n-hexane < isohexane < 2,2,4-trimethylpentane < 2,2,3,3-tetramethylbutane. In contrast, fuel structure is not the main factor in determining acetylene formation. Therefore, matching the benzene formation potential of the surrogate fuel to that produced by the real fuel should have priority when selecting candidate surrogate components for combustion simulations.

Report: Combustion Byproducts and Their Health Effects: Summary of the 10th International Congress.

The 10th International Congress on Combustion Byproducts and their Health Effects was held in Ischia, Italy, from June 17-20, 2007. It is sponsored by the US NIEHS, NSF, Coalition for Responsible Waste Incineration (CRWI), and Electric Power Research Institute (EPRI). The congress focused on: the origin, characterization, and health impacts of combustion-generated fine and ultrafine particles; emissions of mercury and dioxins, and the development/application of novel analytical/diagnostic tools. The consensus of the discussion was that particle-associated organics, metals, and persistent free radicals (PFRs) produced by combustion sources are the likely source of the observed health impacts of airborne PM rather than simple physical irritation of the particles. Ultrafine particle-induced oxidative stress is a likely progenitor of the observed health impacts, but important biological and chemical details and possible catalytic cycles remain unresolved. Other key conclusions were: (1) In urban settings, 70% of airborne fine particles are a result of combustion emissions and 50% are due to primary emissions from combustion sources, (2) In addition to soot, combustion produces one, possibly two, classes of nanoparticles with mean diameters of ~10 nm and ~1 nm. (3) The most common metrics used to describe particle toxicity, viz. surface area, sulfate concentration, total carbon, and organic carbon, cannot fully explain observed health impacts, (4) Metals contained in combustion-generated ultrafine and fine particles mediate formation of toxic air pollutants such as PCDD/F and PFRs. (5) The combination of metal-containing nanoparticles, organic carbon compounds, and PFRs can lead to a cycle generating oxidative stress in exposed organisms.

Real-time measurements of jet aircraft engine exhaust.

Particulate-phase exhaust properties from two different types of ground-based jet aircraft engines--high-thrust and turboshaft--were studied with real-time instruments on a portable pallet and additional time-integrated sampling devices. The real-time instruments successfully characterized rapidly changing particulate mass, light absorption, and polycyclic aromatic hydrocarbon (PAH) content. The integrated measurements included particulate-size distributions, PAH, and carbon concentrations for an entire test run (i.e., "run-integrated" measurements). In all cases, the particle-size distributions showed single modes peaking at 20-40nm diameter. Measurements of exhaust from high-thrust F404 engines showed relatively low-light absorption compared with exhaust from a turboshaft engine. Particulate-phase PAH measurements generally varied in phase with both net particulate mass and with light-absorbing particulate concentrations. Unexplained response behavior sometimes occurred with the real-time PAH analyzer, although on average the real-time and integrated PAH methods agreed within the same order of magnitude found in earlier investigations.

Simulation of the evolution of particle size distributions in a vehicle exhaust plume with unconfined dilution by ambient air.

Over the past several years, numerous studies have linked ambient concentrations of particulate matter (PM) to adverse health effects, and more recent studies have identified PM size and surface area as important factors in determining the health effects of PM. This study contributes to a better understanding of the evolution of particle size distributions in exhaust plumes with unconfined dilution by ambient air. It combines computational fluid dynamics (CFD) with an aerosol dynamics model to examine the effects of different streamlines in an exhaust plume, ambient particle size distributions, and vehicle and wind speed on the particle size distribution in an exhaust plume. CFD was used to calculate the flow field and gas mixing for unconfined dilution of a vehicle exhaust plume, and the calculated dilution ratios were then used as input to the aerosol dynamics simulation. The results of the study show that vehicle speed affected the particle size distribution of an exhaust plume because increasing vehicle speed caused more rapid dilution and inhibited coagulation. Ambient particle size distributions had an effect on the smaller sized particles (approximately 10 nm range under some conditions) and larger sized particles (>2 microm) of the particle size distribution. The ambient air particle size distribution affects the larger sizes of the exhaust plume because vehicle exhaust typically contains few particles larger than 2 microm. Finally, the location of a streamline in the exhaust plume had little effect on the particle size distribution; the particle size distribution along any streamline at a distance x differed by less than 5% from the particle size distributions along any other streamline at distance x.

Evaluation of catalyzed and electrically heated filters for removal of particulate emissions from diesel-A- and JP-8-fueled engines.

In-service diesel engines are a significant source of particulate matter (PM) emissions, and they have been subjected to increasingly strict emissions standards. Consequently, the wide-scale use of some type of particulate filter is expected. This study evaluated the effect of an Engelhard catalyzed soot filter (CSF) and a Rypos electrically heated soot filter on the emissions from in-service diesel engines in terms of PM mass, black carbon concentration, particle-bound polycyclic aromatic hydrocarbon concentration, and size distribution. Both filters capture PM. The CSF relies on the engine's exhaust to reach the catalyst regeneration temperature and oxidize soot, whereas the electrically heated filter contains a heating element to oxidize soot. The filters were installed on several military diesel engines. Particle concentrations and compositions were measured before and after installation of the filter and again after several months of operation. Generally, the CSF removed at least 90% of total PM, and the removal efficiency improved or remained constant after several months of operation. In contrast, the electrical filters removed 44-69% of PM mass. In addition to evaluating the soot filters, the sampling team also compared the results of several real-time particle measurement instruments to traditional filter measurements of total mass.

Formation of chlorinated aromatics by reactions of Cl*, Cl2, and HCl with benzene in the cool-down zone of a combustor.

Conversion of benzene to chlorobenzenes and monochlorophenols by reaction with chlorine radicals (Cl*) in the cool-down zone of a plug-flow combustor has been studied, and a mechanistic analysis of the initial steps of the oxy-chlorination process is proposed. Superequilibrium concentrations of Cl* are formed during combustion of chlorocarbon species and persist at significant concentration levels even after a substantial reduction in the flue gas temperature (T = 500-700 degrees C). At these temperatures, Cl* attack on benzene present in trace concentrations (initial benzene concentration of 300 ppmv or 1080 ppmv were used for the experiments) in the post-flame gas is shown to result in stable chlorinated products (chlorobenzenes and chlorophenols) and loss of benzene. These results suggest that Cl* attack on trace level aromatics and possibly other organic species may be the initial step in the formation of a broad class of chlorinated and oxy-chlorinated pollutants in the post combustion zone.

Modeling aerosol formation in opposed-flow diffusion flames.

The microstructures of atmospheric pressure, counter-flow, sooting, flat, laminar ethylene diffusion flames have been studied numerically by using a new kinetic model developed for hydrocarbon oxidation and pyrolysis. Modeling results are in reasonable agreement with experimental data in terms of concentration profiles of stable species and gas-phase aromatic compounds. Modeling results are used to analyze the controlling steps of aromatic formation and soot growth in counter-flow configurations. The formation of high molecular mass aromatics in diffusion controlled conditions is restricted to a narrow area close to the flame front where these species reach a molecular weight of about 1000 u. Depending on the flame configuration, soot formation is controlled by the coagulation of nanoparticles or by the addition of PAH to soot nuclei.

Characterization of exhaust particles from military vehicles fueled with diesel, gasoline, and JP-8.

Diluted exhaust from selected military aircraft ground-support equipment (AGE) was analyzed for particulate mass, elemental carbon (EC) and organic carbon (OC), SO4(2-), and size distributions. The experiments occurred at idle and load conditions and utilized a chassis dynamometer. The selected AGE vehicles operated on gasoline, diesel, and JP-8. These military vehicles exhibited concentrations, size distributions, and emission factors in the same range as those reported for nonmilitary vehicles. The diesel and JP-8 emission rates for PM ranged from 0.092 to 1.1 g/kg fuel. The EC contributed less and the OC contributed more to the particulate mass than reported in recent studies of vehicle emissions. Overall, the particle size distribution varied significantly with engine condition, with the number of accumulation mode particles and the count median diameter (CMD) increasing as engine load increased. The SO4(2-) analyses showed that the distribution of SO4(2-) mass mirrored the distribution of particle mass.

The origin, fate, and health effects of combustion by-products: a research framework.

Incomplete combustion processes can emit organic pollutants, metals, and fine particles. Combustion by-products represent global human and environmental health challenges that are relevant not only in heavily industrialized nations, but also in developing nations where up to 90% of rural households rely on unprocessed biomass fuels for cooking, warmth, and light. These issues were addressed at the Seventh International Congress on Combustion By-Products, which convened 4-6 June 2001 in Research Triangle Park, North Carolina. This congress included a diverse group of multidisciplinary researchers and practitioners who discussed recent developments and future goals in the control of combustion by-products and their effects of exposure on human and ecologic health. Participants recommended that interdisciplinary, coordinated research efforts should be focused to capitalize on the important potential synergisms between efforts to reduce the adverse human health effects linked to exposures to combustion by-products and broader efforts to reduce greenhouse gas emissions and save energy through efficiency. In this article we summarize the principal findings and recommendations for research focus and direction.