Analysis of Postoperative Complication and Revision Rates and Mid- to Long-Term Implant Survival in Primary Short-Stem Total Hip Arthroplasty.

Background/Objectives: Short-stem prostheses were introduced as an alternative to conventional straight-stem prostheses. Despite their benefits, including minimally invasive approaches, soft-tissue- and bone-sparing implantation, and physiological load transfer to the metaphysis, data on postoperative complication and revision rates as well as on implant survival are scarce. Methods: A retrospective analysis of 1327 patients who underwent primary total hip arthroplasty (THA) using the Metha® short stem between 2006 and 2023 was conducted. Complication and revision rates were analysed for the intraoperative, direct postoperative, and follow-up episodes. Implant survival was analysed with the endpoint of all-cause stem revision. Results: Intraoperative complications were observed in 3.77% of the cases and included 44 hairline cracks and 6 fractures. In 15 cases (30.0%), conversion to a straight-stem or revision implant was necessary. The direct postoperative complication rate was 2.44%, and 11 revision procedures were performed during inpatient stay (0.84%). Mean follow-up was 7 years (range 1-17). During follow-up, femoral component revision was performed in 60 cases. Aseptic loosening and stem subsidence accounted for a combined percentage of 80% of all indications. Implant survival rate was 95.66% after 5 years, 95.58% after 10 years, and 95.50% after 15 years. Conclusions: Our study provides a comprehensive analysis of postoperative complication and revision rates in a large sample undergoing primary short-stem THA. Postoperative complication rates were favourable, and the long-term implant survival rates were comparable to conventional straight-stem prostheses. Therefore, short-stem THA may be considered an alternative for younger patients.

Defining Distinct Stress Curve Morphologies for Coronal Plane Alignment of the Knee Phenotypes Using an Imageless Navigation Robotic Platform in Total Knee Arthroplasty.

BACKGROUND: The coronal plane alignment of the knee (CPAK) classification system divides coronal knee anatomy into 9 phenotypes, suggesting different soft tissue balancing is needed for optimal outcomes. We investigated the interplay between CPAK phenotypes and gap stress curves throughout the knee's range of motion, aiming to understand their impact on total knee arthroplasty balancing. METHODS: There were 1,112 total knee arthroplasty cases from 2 imageless robotic assisted navigation systems using posterior stabilized implants that were classified into CPAK phenotypes. Medial and lateral initial gap values were measured throughout the knee flexion-extension arc, gap curve morphologies were generated, and mediolateral (ML) gap balance was calculated for each phenotype. The most common phenotypes were included in this study, CPAK I to VI. RESULTS: Each phenotype exhibited a distinct gap curve morphology. Type I maintained the largest ML gap difference (-3.6 to -2.1), with the medial compartment tightest in extension. Type II showed relative laxity in the lateral compartment compared to the medial gap (-1.0 to -1.9), with the medial compartment tightening through flexion. Type III had a looser medial and tighter lateral compartment in extension that inverts to a tighter medial compartment in deep flexion (2.1 to -0.8), while Type IV showed a decreasing compartment difference with increased flexion (-3.7 to 0.6). Type V had fluctuating tightness (-0.6 to 1.8), and Type VI had the medial compartment tightening more with flexion (0.6 to 1.8). CONCLUSIONS: The distinct stress curves and ML gap behavior provide a "fingerprint" for each corresponding CPAK phenotype. Investigating these morphologies can help determine the best phenotype-specific treatments, including alignment strategy, implant selection, and gap balance, for optimal functional and patient outcomes.

Higher satisfaction and function scores in restricted kinematic alignment versus mechanical alignment with medial pivot design total knee arthroplasty: A prospective randomised controlled trial.

PURPOSE: Restricted kinematic alignment (rKA) in total knee arthroplasty (TKA) and medial pivot (MP) knee designs already showed superior outcomes in independent comparative studies. The objective of this study was to assess whether rKA with MP TKA provides better clinical and functional outcomes compared to mechanical alignment (MA) with MP TKA. METHODS: This is a randomised, parallel two group study involving a total of 98 patients with end-stage knee osteoarthritis. Patients were randomly allocated to either rKA or MA TKA procedures conducted with a MP prothesis using patient-specific instruments between 2017 and 2020. Final follow-up was at 2 years postoperatively. Demographic data and clinical and functional scores (Oxford knee score, knee society score [KSS], Western Ontario and McMaster Universities Osteoarthritis Index [WOMAC], forgotten joint score [FJS]) were collected and compared preoperative, 1 year postoperative and 2 years postoperative. Coronal plane alignment of the knee and functional knee phenotype classification were recorded. RESULTS: A total of 47 patients (rKA) and 51 patients (MA) were included in final analysis. Superior joint awareness scores (FJS) were found at 1 year postoperative for rKA (62.2 vs. 52.4, p = 0.04). KSS subscores (expectation score, satisfaction score) improved with rKA with significant differences at both 1 and 2 years postoperatively. Major differences between rKA and MA were found in subgroup analysis of varus and neutral CPAK phenotypes. Both 1 year and 2 years postoperatively, FJS was significantly better in KA compared with MA in varus CPAK phenotypes (63.1 vs. 44.9, p = 0.03; 71.1 vs. 46.0, p = 0.005). Further clinical and functional scores showed improvement in the varus CPAK phenotypes with predominantly significant improvement in the expectation and satisfaction KSS subscores. No significant differences were found in the comparison of rKA and MA in neutral CPAK phenotypes. CONCLUSION: The rKA of MP TKA design shows superior patient satisfaction and self-reported function when compared to MA MP TKA. Furthermore, rKA MP TKA shows superior joint awareness at early postoperative stage. The most important clinical relevance of this study is the clear superiority of rKA in varus phenotypes. LEVEL OF EVIDENCE: Level II.

The prognostic significance of surgical resection margins for local recurrence, distant metastasis, and overall survival in sarcoma.

BACKGROUND AND OBJECTIVES: Surgical resection with microscopically negative margins constitutes one of the key elements of a curative therapeutic approach for localized sarcomas. However, the prognostic value of quantitative margin width remains controversial. We sought to determine the prognostic significance of margin status and margin width for local recurrence (LR), distant recurrence (DR), and overall survival. METHODS: Retrospective analysis of 210 patients undergoing resection of localized sarcoma between 1997 and 2018 at a national sarcoma reference center. RESULTS: Logistic regression did not reveal an effect of metric margin width as a prognostic factor for LR (odds ratio [OR] = 0.98, p = 0.574), DR (OR = 1, p = 0.908), or overall survival (hazard ratio = 0.98, 95% confidence interval = 0.73-1.20, p = 0.609). Subgroup analysis revealed no differences between complete first resections (R0) and re-resections (re-R0) following unplanned R1-resections for LR (p = 0.727) and overall survival (p = 0.125), but a significantly higher DR-rate in re-R0 cases (p = 0.022). CONCLUSIONS: Achieving a negative margin is essential in sarcoma surgery, however, metric margin width was not associated with disease-specific outcomes. Re-resection of unplanned R1-resections should be performed to control for LR and overall survival rates. As re-R0 cases were at significantly higher risk of DR, these patients should be followed up closely in standardized surveillance protocols.

Comparable accuracy of femoral joint line reconstruction in different kinematic and functional alignment techniques.

PURPOSE: A key part of kinematic alignment (KA) and functional alignment (FA) is to restore the natural femoral joint line, in particular the medial joint line. KA is known to reproduce the femoral joint line accurately; however, direct comparisons with other surgical techniques such as FA are currently lacking. The purpose of this study was to evaluate differences of alignment parameters in KA and FA techniques with a special focus given to the femoral joint line. METHODS: We performed a retrospective radiological analysis of pre- and postoperative long leg radiographs of 221 consecutive patients with varus or neutral leg alignment, who underwent primary total knee arthroplasty (TKA) procedures from 2018 to 2020. Patients were assigned to one of four groups: (1) FA: image-based robotic-assisted TKA, (2) FA: imageless robotic-assisted TKA, (3): restricted KA: 3D cutting block-assisted (patient-specific instruments, PSI) TKA, (4): unrestricted KA: calipered technique. Patients' radiographs were (re)-analyzed for overall limb alignment, medial proximal tibial angle (MPTA), lateral distal femoral angle (LDFA), as well as medial and lateral femoral joint line alteration. Statistical significance was determined using unpaired t testing (FA vs. KA group) and one-way ANOVA (subgroup analyses). RESULTS: Comparisons of KA vs. FA, as well as individual subgroups of KA and FA did not show any differences in the accuracy of medial joint line reconstruction (< 2 mm, p = 0.384, p = 0.744, respectively) and LDFA alteration (< 2°, p = 0.997, 0.921, respectively). Correction of MPTA (3.4° vs. 2.2°) and lateral femoral joint line (2.1 mm vs. 1.5 mm) was higher for FA and FA subgroups compared to KA and KA subgroups (both p < 0.001). CONCLUSION: Kinematic and functional alignments showed a comparable accuracy in reconstruction of the medial femoral joint line and femoral joint line orientation. Increased correction of MPTA and lateral femoral joint line was recorded with FA techniques. LEVEL OF EVIDENCE: III.

[Kinematic Alignment of Total Knee Arthroplasty]. / Kinematisches Alignment bei der Knie-TEP-Implantation.

Nowadays, kinematic alignment is a widely used alignment philosophy in total knee arthroplasty. The concept of kinematic alignment respects the patient's individual prearthrotic anatomy and is based on the reconstruction of the femoral anatomy and thus the axes of motion of the knee joint. Only then the alignment of the tibial component is adapted to the femoral component. By means of this technique soft tissue balancing is reduced to a minimum. Due to the risk of excessive outlier alignment technical assistance or calipered techniques are recommended for precise implementation. This article attempts to provide an understanding of the fundamentals of kinematic alignment, and it focusses on how it differs from alternative alignment strategies and the way the philosophy is implemented in different surgical techniques.

Noise exposure during robot-assisted total knee arthroplasty.

The aim of the study was to examine the noise exposure for operating theater staff during total knee arthroplasty (TKA) with three different robot systems. There is already evidence that noise exposure during TKA performed manually exceeds recommended guidelines for occupational noise. Therefore, if surgical staff is exposed to it for several years, the development of noise-inducing hearing loss (NIHL) is significantly increased. To investigate the noise exposure during robot-assisted TKA, the study measured the average noise and the peak sound pressure during TKA with MAKO robot (Stryker, Kalamazoo, Michigan, United States), NAVIO robot (Smith and Nephew, London, Great Britain), and CORI robot (Smith and Nephew, London, Great Britain) using a class 1 sound level meter. Each robot system exceeds the recommended guidelines from the national institute for occupational safety and health. While the MAKO robot had the highest average sound level (93.18 dB(A)) of the three robot systems (NAVIO: 88.88 dB(A), CORI: 89.38 dB(A)), the peak sound level was the highest with the NAVIO Robot (134.48 dB(C)) compared to the MAKO Robot (128.98 dB(C)) and CORI robot (126.48 dB(C)). Robot-assisted TKA is a risk factor for NIHL, like manually performed TKA. Further research for decreasing the noise exposure during TKA is needed to minimize the hearing loss in operating theater staff.

Robotic-assisted TKA reduces surgery duration, length of stay and 90-day complication rate of complex TKA to the level of noncomplex TKA.

INTRODUCTION: Complex primary total knee arthroplasties (TKA) are reported to be associated with excessive episode of care (EOC) costs as compared to noncomplex procedures. The impact of robotic assistance (rTKA) on economic outcome parameters in greater case complexity has not been described yet. The purpose of this study was to investigate economic outcome parameters in the 90-days postoperative EOC in robotic-assisted complex versus noncomplex procedures. MATERIALS AND METHODS: This study is a retrospective, single-center review of 341 primary rTKAs performed between 2017 and 2020. Patient collective was stratified into complex (n = 218) and noncomplex TKA (n = 123) based on the presence of the following criteria: Obese BMI, coronal malalignment, flexion contracture > 10°, posttraumatic status, previous correction osteotomy, presence of hardware requiring removal during surgery, severe rheumatoid arthritis. Group comparison included surgery duration, length of stay (LOS), surgical site complications, readmissions, and revision procedures in the 90-days EOC following rTKA. RESULTS: The mean surgery duration was marginally longer in complex rTKA, but showed no significant difference (75.26 vs. 72.24 min, p = 0.258), neither did the mean LOS, which was 8 days in both groups (p = 0.605). No differences between complex and noncomplex procedures were observed regarding 90-days complication rates (7.34 vs. 4.07%, p = 0.227), readmission rates (3.67 vs. 3.25%, p = 0.841), and revision rates (2.29 vs. 0.81%, p = 0.318). CONCLUSIONS: Robotic-assisted primary TKA reduces the surgical time, inpatient length of stay as well as 90-days complication and readmission rates of complex TKA to the level of noncomplex TKA. Greater case complexity does not seem to have a negative impact on economic outcome parameters when surgery is performed with robotic assistance.

[Market overview: Robotic-assisted arthroplasty : Current robotic systems, learning curve and cost analysis]. / Marktübersicht: Roboterassistierte Endoprothetik : Aktuelle Robotersysteme, Lernkurven und Kostenanalyse.

Robotic-assisted arthroplasty has been rapidly entering clinical routine in recent years. The leading endoprosthesis manufacturers have all meanwhile placed robotic systems on the market, which, however, differ significantly from one another technically. Current systems are currently classified according to the degree of autonomy (active vs. semi-active vs. passive) and the data/image source (image-based: CT vs. X­ray, imageless). Some systems already offer the possibility of robotic-assisted or navigated implantation of hip endoprostheses. In the following review article, the currently leading robotic systems will be presented and compared with regard to their characteristics. Furthermore, the analysis of the learning curves for the different systems, currently available cost analysis models and an outlook on future developments and challenges will be given.

[Strategic approach in periprosthetic joint infections]. / Strategisches Vorgehen bei chronischen Infektionen von Endoprothesen.

With rising numbers of revisions of total arthroplasty procedures of the lower extremities, the annual number of cases of implant-associated infection are also increasing. The conventional two-stage replacement strategy often leads to increased morbidity and mortality of patients; however, in the literature a one-stage exchange procedure shows equally good results if the indications are strictly defined. In addition to the correct diagnostics, the patient history, the inserted implant, the state of health and when applicable the pathogens present play an important role. If, among other factors, the pathogen is uncomplicated combined with a good bone and soft tissue situation and without a large number of previous operations, a single stage replacement of the endoprosthesis may be a suitable option. Despite existing controversies in the literature, this treatment approach seems to demonstrate a reduced hospitalization, reduced costs and improved patient satisfaction with the same re-revision rate. This review article explains the strategic approach to chronic infections of endoprostheses of the lower extremities based on clinical examples and a review of the current literature.

Detailed Revision Risk Analysis after Single- vs. Two-Stage Revision Total Knee Arthroplasty in Periprosthetic Joint Infection: A Retrospective Tertiary Center Analysis.

Periprosthetic joint infection (PJI) remains one of the most common causes of revision knee arthroplasty. Controversy continues to surround the proper operative technique of PJI in knee arthroplasty with single- or two-stage replacement. Significant variations are seen in the eradication rates of PJI and in implant survival rates. This detailed retrospective analysis of a single tertiary center is intended to provide further data and insight comparing single- and two-stage revision surgery. A retrospective analysis of all revision total knee arthroplasty (TKA) surgeries from 2013 to 2019 was performed and screened with respect to single- or two-stage TKA revisions. Single- and two-stage revisions were analyzed with regard to implant survival, revision rate, microbiological spectrum, and other typical demographic characteristics. A total of 63 patients were included, with 15 patients undergoing single-stage revision and 48 patients undergoing two-stage revision. The mean follow-up time was 40.7 to 43.7 months. Statistically, no difference was found between both groups in overall survival (54.4% vs. 70.1%, p = 0.68) and implant survival with respect to reinfection (71.4% vs. 82.4%, p = 0.48). Further, high reinfection rates were found for patients with difficult-to-treat organisms and low- to semi-constrained implant types, in comparison to constrained implant types. A statistically comparable revision rate for recurrence of infection could be shown for both groups, although a tendency to higher reinfection rate for single-stage change was evident. The revision rate in this single-center study was comparably high, which could be caused by the high comorbidity and high proportion of difficult-to-treat bacteria in patients at a tertiary center. In this patient population, the expectation of implant survival should be critically discussed with patients.

Imageless robotic-assisted revision arthroplasty from UKA to TKA : Surgical technique and case-control study compared with primary robotic TKA.

BACKGROUND AND OBJECTIVE: It is evident from the national joint registries that numbers of revision knee arthroplasty operations are rising. The aim of this article is to introduce a new robotic-assisted approach in UKA to TKA revision arthroplasty and investigate the alignment accuracy, implant component use and surgery time and to compare it to primary robotic-assisted TKA arthroplasty. METHODS: This retrospective, case-control study included patients undergoing image-less robotic-assisted revision arthroplasty from UKA to TKA (n = 20) and patients undergoing image-less robotic-assisted primary TKA (control group, n = 20) from 11/2018 to 07/2020. The control group was matched based on the BMI and natural alignment. Comparison of groups was based on postoperative alignment, outlier rate, tibial insert size, lateral bone resection depth, incision-to-wound closure time. All surgeries were performed by a single senior surgeon using the same bi-cruciate stabilizing TKA system. Statistical analysis consisted of parametric t­testing and Fisher's exact test with a level of significance of p < 0.05. RESULTS: The two groups showed no differences in mean BMI, natural alignment (p > 0.05) and mean overall limb alignment. No outlier was found for OLA and slope analysis. The smallest insert size (9 mm) was used in 70% of the cases in the revision group (n = 14) and in 90% of the cases in the primary group (n = 18, p = 0.24), distal femoral and tibial resection depth showed no statistical difference (p > 0.05). The incision to wound closure time was longer in the revision group but showed no significant difference. CONCLUSION: Image-less robotic-assisted revision arthroplasty from UKA to TKA showed a comparable surgery time, and alignment accuracy in comparison to primary robotic-assisted TKA. Comparable bone preservation and subsequent tibial insert size use was observed for both groups.

Robotics improves alignment accuracy and reduces early revision rates for UKA in the hands of low-volume UKA surgeons.

PURPOSE: It is known that in uni-compartmental knee arthroplasty (UKA) low-volume surgeons have a higher complication and revision rate than high-volume surgeons. Further, robotic-assisted UKA leads to lower early revision rate as well as fewer limb and joint line outliers compared to conventional UKA. The purpose of this study was to retrospectively analyze the outliers' and revision rate of low-volume UKA surgeons with different robotic systems at short-term follow-up. METHODS: In this case-control study, 103 robotic-assisted UKAs were included. The procedures were performed between 2016 and 2019 from two low-volume UKA surgeons with an imageless (IL) (63 patients) and image-based (IB) (40 patients) robotic system. Alignment outliers, joint line (JL) reconstruction, complication and revision rates of the two different robotic systems were analyzed. The minimum follow-up was two years. Outliers were defined as a postoperative valgus malalignment greater than 182°. The surgery time for all procedures was evaluated. RESULTS: The overall revision rate was 3.9% (4 of 103). Two occurred in the IB group (5.0%) and two in the IL group (3.2%). No valgus malalignment outliers were observed in both groups. The mean JL was not distalized by more than 2 mm in both groups (IL: 1.3 ± 1.6 mm vs. IB: 1.8 ± 0.9 mm, p value 0.08). The IL procedures had a significant lower mean surgery time (55 ± 13 min vs. 68 ± 14, p value 0.001). CONCLUSION: Robotic-assisted UKA is a safe procedure in the hand of low-volume UKA surgeons. Robotic-assisted UKA minimizes overcorrection into valgus mal-alignment. Low revision rates are observed at short-term follow-up for robotic-assisted UKA. The choice of the different robotic systems has no impact on the outcome.

Imageless robotic handpiece-assisted total knee arthroplasty: a learning curve analysis of surgical time and alignment accuracy.

INTRODUCTION: Robotic-assisted surgery techniques are increasing in total knee arthroplasty (TKA). One crucial point is the prolonged time of surgery. The primary objective of this study was to determine the learning curve necessary to minimize the time of surgery. The secondary objective was to evaluate the accuracy of the implant alignment when using an imageless robotic system for TKA. MATERIALS AND METHODS: In a case-control study, the first 70 consecutive robotic-assisted TKA procedures performed by a single senior surgeon were analyzed with regard to surgery time and implant alignment by comparing the intraoperative plan with the postoperative alignment. The evaluation of the learning curve with respect to surgery time was conducted using cumulative summation (CUSUM) analysis. The joint line height was measured with a new technique. Surgery time and joint line reconstruction were compared to 70 consecutive conventional TKA procedures. RESULTS: The learning curve for robotic TKA was completed after 11 cases. The learning curve did not influence the accuracy of joint line obliquity, joint line height, or limb alignment. The intraoperative plan designed for the robotic system was precisely implemented. The mean skin-to-skin time in the robotic group after the learning curve was completed did not differ from that in the manual group. A significant positive correlation was observed between the preoperative hip-knee-ankle angle and the postoperative distalization of the joint line in the robotic-assisted TKA group. CONCLUSION: After completing the initial learning curve of 11 cases, the surgery time required to perform imageless robotic handpiece-assisted TKA was similar to that for the conventional technique. However, no learning curve was observed for the implant positioning when using the imageless robotic system. The implementation of the intraoperative plan was accurate up to < 2°. The precision of the system allows the implementation of different joint balancing approaches between valgus and varus morphotypes.

Individual Revision Knee Arthroplasty Is a Safe Limb Salvage Procedure.

INTRODUCTION: Revision total knee arthroplasty after multiple pre-surgeries is challenging. Due to severe bone defects, standard implants for metaphyseal and diaphyseal anchoring may no longer be suitable. The primary aim of this case series is to evaluate the early complication rate for individual knee implants with custom-made cones and stems after two-stage revision with severe bone defects. METHODS: Ten patients who were treated with custom-made 3D-printed knee revision implants were included. Inclusion criteria were a two-stage revision due to late-onset or chronic periprosthetic joint infection as well as aseptic loosening. All severe bone defects were AORI type III. All procedure-related complications were evaluated. Postoperative range of motion after one year was measured. The time between the two surgeries was evaluated. RESULTS: The mean follow-up was 21 months (range: 12-40). The mean time between the two-stage surgeries was 71.6 days. No fractures were observed intra- and postoperatively. Two patients were revised without changing metal components due to persistent hematoma (three weeks post-surgery) and persistent PJI (three months post-surgery). The mean passive postoperative range of motion was 92° (range: 80-110°). CONCLUSIONS: Individual custom-made implants for rTKA provide a safe procedure for patients with huge bone defects after several pre-surgeries. If standard knee systems with standard cones or sleeves are not suitable anymore, custom-made treatment offers the patient the last option for limb preservation. However, this is associated with increased costs.

CT based PSI blocks for osteotomies around the knee provide accurate results when intraoperative imaging is used.

PURPOSE: Correction osteotomies around the knee are common methods for the treatment of varus or valgus malalignment of the lower extremity. In recent years, patient specific instrumentation (PSI) guides were introduced in order to enhance the accuracy of these procedures. The purpose of this study was to determine the accuracy of CT based PSI guides for correction osteotomies around the knee of low volume osteotomy surgeons and to evaluate if CT based PSI blocks deliver a high degree of accuracy without using intraoperative fluoroscopy. METHODS: Two study arms with CT based PSI cutting blocks for osteotomies around the knee were conducted. Part one: A retrospective analysis of 19 osteotomies was made in order to evaluate the accuracy in the hands of a low volume surgeon on long-leg radiographs. Part two: A cadaveric study with 8 knees was performed for the purpose of analyzing the accuracy without using intraoperative fluoroscopy on pre- and postoperative CT scans. Hip-Knee-Ankle angle (HKA), lateral distal femoral angle (LDFA) and medial proximal tibial angle (MPTA) were analyzed. The mean absolute delta (∂) between the planned and postoperative parameters were calculated. The accuracy of both study arms were compared. RESULTS: Part one: The mean MPTA ∂, LDFA ∂ and HKA ∂ was 0.9°, 1.9° and 1.5°, respectively. Part two: The mean MPTA ∂ and LDFA ∂ was 3.5° and 2.2°, respectively. The mean ∂ of MPTA is significantly different between clinical patients with fluoroscopic control and cadaveric specimens without fluoroscopic control (P < 0.001). All surgeries were performed without complications such as a hinge fracture. CONCLUSION: The clinical use of PSI guides for osteotomies around the knee in the hands of low volume surgeons is a safe procedure. The PSI guides deliver a reliable accuracy under fluoroscopic control whereas their non-use of intraoperative fluoroscopy leads to a lack of accuracy. The use of fluoroscopic control during PSI guided correction osteotomies is highly recommended. LEVEL OF EVIDENCE: IV - Retrospective and experimental Study.

3D-surface scan based validated new measurement technique of femoral joint line reconstruction in total knee arthroplasty.

PURPOSE: This study aimed to validate a new joint line measurement technique in total knee arthroplasty for separated assessment of the medial and lateral femoral joint line alteration with 3D-surface scan technology. Separate assessment of the medial and lateral joint line alteration may improve TKA alignment assessment regarding to joint line restoration in kinematic alignment and use of robotic-assisted TKA surgery. METHODS: The medial and lateral joint line difference after TKA implantation on an artificial bone model was analyzed and compared with a 3D-scan and full femoral radiographs pre- and postoperatively. Radiographic analysis included the perpendicular distance between the most distal point of the medial and lateral condyle and the reproduced preoperative lateral distal femoral angle (LDFA). For evaluation of validity and reliability, radiographs were captured initially with true anteroposterior view and subsequently with combined flexion and rotation malpositioning. Reliability of the introduced measurement technique in between three observers was tested with intraclass correlation coefficient (ICC). RESULTS: Radiographic measurement showed a mean difference of 0.9 mm on the medial side and 0.6 mm on the lateral side when compared to the 3D-surface scan measurement. The reliability of measurement accuracy was ≤ 1 mm in x-rays with < 10° flexion error regardless to malrotation in these images. The ICC test showed very good reliability for the medial joint line evaluation and good reliability for lateral joint line evaluation (ICC 0.92, ICC 0.86 respectively). CONCLUSION: The new introduced joint line measurement method showed a sufficient reliability, accuracy and precision. It provides separated information about medial and lateral joint line alteration in TKA surgery in absolute values. LEVEL OF EVIDENCE: V - Experimental Study.

[End-of-stem pain in hip and knee arthroplasty]. / Schaftschmerz in der Knie- und Hüftendoprothetik.

End-of-stem pain after knee and hip arthroplasty with diaphyseal supportive stems is a frequently overlooked and potentially underestimated complication. A commonly recurring clinical phenome is the symptom-free interval after surgery of weeks to months, with new onset of symptoms under stress only later. The patient is often again reliant on walking sticks. End-of-stem pain is a diagnosis of exclusion. Pain is projected into the tip of the stem, and if differential diagnoses such as loosening are excluded, then the patient might be treated with a "bending-plate". Since bone cement has a similar elastic modulus to human cortical bone, a change of method to a cemented implant can also be expedient. In the primary situation, in addition to cemented stems, the use of "split-stems" could be useful. After revision surgery of any kind, a timely cessation of pain confirms the diagnosis.

Higher revision rate for posterior cruciate-retaining than posterior-stabilized total knee arthroplasty for the treatment of valgus osteoarthritis.

PURPOSE: Determining the point at which a valgus deformity requires a more invasive therapy-in this case PS TKA-is surgically challenging. Retaining the posterior cruciate ligament has both advantages and disadvantages. The aim was to evaluate the failure rate and clinical outcomes. METHODS: 248 patients with valgus gonarthrosis underwent surgical treatment: 167 CR TKA cases and 81 PS TKA cases. The KOOS and the OKS were recorded, and 201 patients (133 CR, 68 PS) were recruited into the retrospective study. The influence of BMI and degree of preoperative valgus deformity on the clinical outcome was determined. The revision rate was documented and analysed. RESULTS: Of 201 patients, 10 required revision surgery owing to instability (10/133 CR, 0/68 PS). Based on the KOOS and the OKS, no significant difference between CR TKA and PS TKA was found. BMI and degree of valgus deformity had no effect on the clinical outcome. CONCLUSIONS: No difference in the clinical outcome between the CR and PS TKA patients was found. In the CR group, significantly more patients showed 'excellent' OKS than in the PS group. However, 8.0% of the patients in the CR group and none in the PS group underwent surgery due to instability. A higher rate of dissatisfied patients in the CR group is likely. In our clinic, we no longer perform CR TKA for valgus cases.