RESUMO
BACKGROUND: A posterior tooth's occlusal surfaces and the proximal surface can be restored by using an inlay, which is an intra-crown cast reconstruction without affecting the cusps of the tooth. When an inlay is prepared using an indirect approach, issues with traditional filling approaches, including poor morphology of the occlusal aspect or proximal aspect, inadequate resistance to wear, or subpar mechanical qualities of the directly inserted filler substance, are overcome. AIM: The current study was conducted in order to compare and assess the resistance to fracture of dental materials used in the preparation of inlay restorations indirectly, like composite restorations prepared by laboratories indirectly, inlays formed indirectly of monolithic translucent ceramic derived from zirconia, and inlays formed indirectly of traditional monolithic ceramic derived from zirconia. METHODS AND MATERIALS: For the investigation, 100 human premolars of the maxilla that were extracted recently were chosen. A self-polymerizing acrylic resin was used to incorporate the tooth roots in a band made up of polyvinyl chloride up to 2 mm below the cement-enamel junction. The dimension of the band was 1.3 cm by 1.9 cm. Five categories of 20 specimens of such teeth were formed. Category one, featuring teeth in good condition, acted as the positive control category. The remaining four categories of teeth received inlay tooth preparation. The research samples underwent thermocycling after having been preserved for a full week following the cementation of inlay replacements. Then, in a universal testing apparatus, every sample endured axial compressive force with a metal globe delivered vertically at a crosshead rate of 1 mm/minute. The amount of force necessary to cause a fracture was measured in Newtons (N). RESULTS: The mean values of resistance against fracture in specimens in categories 1-5 were 1208.87 N, 614.89 N, 733.05 N, 1179.14 N, and 1148.49 N, respectively. The values of fracture resistance in specimens where an inlay cavity preparation was done but not filled were lower than those in traditional monolithic ceramic derived from zirconia and tooth specimens with inlays formed of monolithic translucent ceramic derived from zirconia, and the difference was significant statistically (p=0.001). The values of fracture resistance in composite inlay restorations prepared by laboratories were indirectly lower than those of monolithic ceramic derived from zirconia and tooth specimens with inlays formed of monolithic translucent ceramic derived from zirconia, and the difference was significant statistically (p=0.004). CONCLUSION: Within the constraints of the current investigation, we can state that indirect zirconia-based ceramic products offer adequate fracture resistance, but additional research is needed to determine how well these materials hold up under different types of pressures before employing them in clinical tooth restoration.
RESUMO
BACKGROUND: The present study was conducted to evaluate the clinical efficacy of resin infiltration technique alone or in combination with microabrasion and in-office bleaching in adults with mild-to-moderate fluorosis stains on permanent maxillary anterior teeth at the end of 1 month. MATERIALS AND METHODS: A total of 30 patients with nonpitted fluorosis stains on maxillary anterior were classified as mild (n = 15) and moderate (n = 15). Each grade is subdivided into three groups as Group A, Group B, and Group C. Group 1: Mild (score 2), Subgroup A: Resin infiltration (n = 5 patients), Subgroup B: Microabrasion followed by resin infiltration (n = 5 patients), Subgroup C: Microabrasion and bleaching followed by resin infiltration after 2 weeks (n = 5 patients). Group 2: Moderate (score 3), Subgroup A: Resin infiltration (n = 5 patients), Subgroup B: Microabrasion followed by resin infiltration (n = 5 patients), and Subgroup C: Microabrasion and bleaching followed by resin infiltration after 2 weeks (n = 5 patients). Microabrasion was performed with the opalustre kit from Ultradent according to the manufacturer's instructions. Pola office bleaching from SDI and Icon infiltrant was performed. Stain score, improvement in appearance score, need for further treatment, patient satisfaction score, tooth sensitivity immediately after treatment, 24 h and 72 h were recorded. RESULTS: The mean appearance score in Group 1A was 73.60, in Group 1B was 72.87, in Group 1C was 65.27, in Group 2A was 68.00, in Group 2Bwas 72.93 and in Group 2C was 84.73. The mean need for further treatment score in Group 1A was 72.80, in Group 1B was 78.40, in Group 1C was 68.73, in Group 2A was 71.20, in Group 2B was 79.53 and in Group 2C was 88.73. The mean patient satisfaction score in Group 1A was 91.40, in Group 1B was 95.20, in Group 1C was 98.00, in Group 2A was 90.20, in Group 2B was 99.40 and in Group 2C was 100.00. There was a significant difference in mean tooth sensitivity immediately after treatment between Groups 1A, 1B, 1C, 2A, 2B, and 2C. There was a significant difference in mean tooth sensitivity after 24 h between Groups 1A, 1B, 1C, 2A, 2B, and 2C. CONCLUSION: Resin infiltration technique in combination with bleaching and microabrasion technique found to be effective in the management of dental fluorosis.