Biomechanical analysis of maxillary expansion in CLP patients.

OBJECTIVE: To carry out a comparative biomechanical analysis of maxillary low force expansion using the quadhelix appliance in cleft and noncleft patients. We also intended to determine whether a sufficient transverse skeletal effect could be achieved among cleft patients using the quadhelix appliance. MATERIALS AND METHODS: Three finite element models of the viscerocranium and neurocranium were established in which a transverse expansion of the maxilla using a quadhelix (transverse force of 2 N) was simulated. RESULTS: The skeletal effects at the anatomic structures of the midface and the cranial base were far more marked in the simulation models with clefts compared to the morphologically normal state. The highest expansions were measured for bilateral cleft palates. Thus, the expansion measured at the supraorbital margin was 4.7 mustrain with a bilateral cleft, 2.1 mustrain with a unilateral cleft, and only 0.2 mustrain with the morphologically normal state. For bilateral and also for unilateral bone clefts, the skeletal effect of a maxillary low force expansion with a quadhelix on the anatomical structures of the viscerocranium and neurocranium is very much larger than is the case for individuals without clefts. CONCLUSION: In the presence of a continuous cleft in the jaw and palate area, orthodontic forces (quadhelix) are apparently already sufficient to allow a skeletal expansion of the maxilla. Maxillary expansion using the quadhelix appliance represents a reasonable alternative to using conventional rapid maxillary expansion appliances among cleft patients.

Accuracy of facial plaster casts.

OBJECTIVE: The aim of this study was to evaluate the accuracy of facial plaster casts and their suitability for 3-D mapping. MATERIALS AND METHODS: All measurements were carried out on 15 adult probands (seven female and eight male; age range 19-31 years, mean 24.7 years). A plaster cast of the facial surface was prepared for all probands using alginate impressions. The plaster casts and the probands faces were digitized using a three-dimensional laser-scanner operating with structured light. The resulting point clouds were matched in a virtual environment to analyze the deviations between the cast and the facial surfaces, both qualitatively and quantitatively. RESULTS: The average deviations depended on the facial area and lay between 0.95 and 3.55 mm. Marked differences between the plaster cast and the facial surface were found, particularly in the area of the lips, at the roof of the nose, at the cheeks, and in the entire lower facial area. CONCLUSIONS: The regionally exacerbated soft tissue deformations that occur during impression of the facial surface lead to inaccuracies in the resulting plaster cast that forbids any use for morphometric analysis. Documentation of pathological findings in cleft lip and palate using facial plaster casts does appear to be justifiable.

Three-dimensional soft tissue prediction using finite elements. Part II: Clinical application.

BACKGROUND AND AIM: The goal of this study was to analyze the validity and prediction accuracy of a newly-developed procedure for three-dimensional soft tissue prediction based on Finite Element Method, and to compare the results with prediction produced using an existing two-dimensional prediction program (Dentofacial Planner Plus). PATIENTS AND METHODS: In twelve patients who underwent combined surgical-orthodontic treatment, profile prediction was generated using both procedures preoperatively and then compared at predefined measurement points with the patient's actual postoperative soft tissue status. RESULTS: The deviations observed depended on the facial region, whereby the prediction errors for both procedures were much greater in the lower facial third than in the midfacial third. Calculating in all the measurement points, the mean horizontal prediction error was 0.32 mm for the Finite Element Method and 0.75 mm for the Dentofacial Planner Plus. Overall, we were able to demonstrate the new procedure's superior validity and quality of visualization. In addition to profile prediction, the procedure allows a differentiated three-dimensional assessment of esthetically important regions such as the cheeks, nasolabial folds and the nasal wings. Additional X-radiation is not necessary in this risk-free and stress-free procedure. CONCLUSION: Three-dimensional soft tissue prediction employing finite element modeling is a useful aid for implementing esthetically-optimized treatment planning.

Three-dimensional soft tissue prediction using finite elements. Part I: Implementation of a new procedure.

BACKGROUND AND AIM: The prediction of soft tissue esthetics is important for achieving an optimal esthetic outcome in orthodontic treatment planning. Applicable procedures have so far been restricted to two-dimensional profile predictions that have not proven to be very reliable. The goal of this investigation was therefore to develop a novel finite element-based procedure that allows a three-dimensional, easily visualized, quantitative analysis and prediction of soft tissue behavior for the clinician. The procedure to be developed should be easy to handle and not entail any additional radiation exposure for the patient. MATERIAL AND METHODS: Using a three-dimensional scanner, the facial surfaces of 20 probands were digitalized and individual FEM models were generated. RESULTS: After reduction of data redundancy via several conversion steps, a patient-specific simulation model was prepared consisting of 20,000 to 40,000 individual elements to which specific physical properties could be assigned. The average time required for generating a virtual model was 50 minutes. Problems occurring during model generation were rare (mainly shadowing phenomena and movement artifacts). CONCLUSION: The procedure outlined herein makes the reliable generation of patient-specific simulation models possible for facial soft tissue prediction in orthodontics.

Clinical evaluation of an Er:YAG laser for nonsurgical treatment of peri-implantitis: a pilot study.

The aim of this controlled, parallel design clinical study was to compare the effectiveness of an Er:YAG laser (ERL) to that of mechanical debridement using plastic curettes and antiseptic therapy for nonsurgical treatment of peri-implantitis. Twenty patients with moderate to advanced peri-implantitis lesions were randomly treated with either (1) an ERL using a cone-shaped glass fiber tip at an energy setting of 100 mJ/pulse and 10 pps (ERL), or (2) mechanical debridement using plastic curettes and antiseptic therapy with chlorhexidine digluconate (0.2%) (C). The following clinical parameters were measured at baseline, 3 and 6 months after treatment by one blinded and calibrated examiner: Plaque index (PI), bleeding on probing (BOP), probing depth (PD), gingival recession (GR) and clinical attachment level (CAL). At the baseline examination, there were no statistically significant differences in any of the investigated parameters. Mean value of BOP decreased in the ERL group from 83% at baseline to 31% after 6 months (P < 0.001) and in the C group from 80% at baseline to 58% after 6 months (P < 0.001). The difference between the two groups was statistically significant (P < 0.001, respectively). The sites treated with ERL demonstrated a mean CAL change from 5.8 +/- 1 mm at baseline to 5.1 +/- 1.1 mm (P < 0.01) after 6 months. The C sites demonstrated a mean CAL change from 6.2 +/- 1.5 mm at baseline to 5.6 +/- 1.6 mm (P < 0.001) after 6 months. After 6 months, the difference between the two groups was statistically not significant (P > 0.05). Within the limits of the present study, it was concluded that (i) at 6 months following treatment both therapies led to significant improvements of the investigated clinical parameters, and (ii) ERL resulted in a statistically significant higher reduction of BOP than C.