RESUMO
Corrosion is a ubiquitous failure mode of materials. Often, the progression of localized corrosion is accompanied by the evolution of porosity in materials previously reported to be either three-dimensional or two-dimensional. However, using new tools and analysis techniques, we have realized that a more localized form of corrosion, which we call 1D wormhole corrosion, has previously been miscategorized in some situations. Using electron tomography, we show multiple examples of this 1D and percolating morphology. To understand the origin of this mechanism in a Ni-Cr alloy corroded by molten salt, we combined energy-filtered four-dimensional scanning transmission electron microscopy and ab initio density functional theory calculations to develop a vacancy mapping method with nanometer-resolution, identifying a remarkably high vacancy concentration in the diffusion-induced grain boundary migration zone, up to 100 times the equilibrium value at the melting point. Deciphering the origins of 1D corrosion is an important step towards designing structural materials with enhanced corrosion resistance.
RESUMO
Scanning transmission electron microscopy (STEM), where a converged electron probe is scanned over a sample's surface and an imaging, diffraction, or spectroscopic signal is measured as a function of probe position, is an extremely powerful tool for materials characterization. The widespread adoption of hardware aberration correction, direct electron detectors, and computational imaging methods have made STEM one of the most important tools for atomic-resolution materials science. Many of these imaging methods rely on accurate imaging and diffraction simulations in order to interpret experimental results. However, STEM simulations have traditionally required large calculation times, as modeling the electron scattering requires a separate simulation for each of the typically millions of probe positions. We have created the Prismatic simulation code for fast simulation of STEM experiments with support for multi-CPU and multi-GPU (graphics processing unit) systems, using both the conventional multislice and our recently-introduced PRISM method. In this paper, we introduce Prismatic version 2.0, which adds many new algorithmic improvements, an updated graphical user interface (GUI), post-processing of simulation data, and additional operating modes such as plane-wave TEM. We review various aspects of the simulation methods and codes in detail and provide various simulation examples. Prismatic 2.0 is freely available both as an open-source package that can be run using a C++ or Python command line interface, or GUI, as well within a Docker container environment.
RESUMO
Organic-inorganic hybrids have recently emerged as a class of high-performing thermoelectric materials that are lightweight and mechanically flexible. However, the fundamental electrical and thermal transport in these materials has remained elusive due to the heterogeneity of bulk, polycrystalline, thin films reported thus far. Here, we systematically investigate a model hybrid comprising a single core/shell nanowire of Te-PEDOT:PSS. We show that as the nanowire diameter is reduced, the electrical conductivity increases and the thermal conductivity decreases, while the Seebeck coefficient remains nearly constant-this collectively results in a figure of merit, ZT, of 0.54 at 400 K. The origin of the decoupling of charge and heat transport lies in the fact that electrical transport occurs through the organic shell, while thermal transport is driven by the inorganic core. This study establishes design principles for high-performing thermoelectrics that leverage the unique interactions occurring at the interfaces of hybrid nanowires.
RESUMO
Solar-driven water splitting using powdered catalysts is considered as the most economical means for hydrogen generation. However, four-electron-driven oxidation half-reaction showing slow kinetics, accompanying with insufficient light absorption and rapid carrier combination in photocatalysts leads to low solar-to-hydrogen energy conversion efficiency. Here, we report amorphous cobalt phosphide (Co-P)-supported black phosphorus nanosheets employed as photocatalysts can simultaneously address these issues. The nanosheets exhibit robust hydrogen evolution from pure water (pH = 6.8) without bias and hole scavengers, achieving an apparent quantum efficiency of 42.55% at 430 nm and energy conversion efficiency of over 5.4% at 353 K. This photocatalytic activity is attributed to extremely efficient utilization of solar energy (~75% of solar energy) by black phosphorus nanosheets and high-carrier separation efficiency by amorphous Co-P. The hybrid material design realizes efficient solar-to-chemical energy conversion in suspension, demonstrating the potential of black phosphorus-based materials as catalysts for solar hydrogen production.
RESUMO
Few-layer black phosphorus (BP) nanosheets were first reported as a 2D material for the application of field-effect transistors in 2014 and have stimulated intense activity among physicists, chemists, and material and biomedical scientists, driving research into novel synthetic techniques to produce BP nanosheets. At present, exfoliation is the main route toward few-layer BP nanosheets via employing bulk BP as raw material. However, this is a complicated and time-consuming process, which is difficult for the large-scale synthesis of BP nanosheets. Moreover, BP degrades rapidly when exfoliated to nanoscale dimensions, resulting in the rapid loss of semiconducting properties. Here, we report the direct wet-chemical synthesis of few-layer BP nanosheets in gram-scale quantities in a bottom-up approach based on common laboratory reagents at low temperature, showing excellent stability due to partial oxidation of surface. Solvent and temperature are two critical factors, controlling not only the formation of BP nanosheets but also the thickness. The as-prepared BP nanosheets can extract hydrogen from pure water (pH = 6.8), exhibiting more than 24-fold higher activity than the well-known C3N4 nanosheets. Our results reporting the ability to prepare few-layer BP nanosheets with a facile, scalable, low-cost approach take us a step closer to real-world applications of phosphorene including next-generation metal-free photocatalysts for photosynthesis.
RESUMO
Photoelectrochemical (PEC) cells are attractive for storing solar energy in chemical bonds through cleaving of water into oxygen and hydrogen. Although hematite (α-Fe2 O3 ) is a promising photoanode material owing to its chemical stability, suitable band gap, low cost, and environmental friendliness, its performance is limited by short carrier lifetimes, poor conductivity, and sluggish kinetics leading to low (solar-to-hydrogen) STH efficiency. Herein, we combine solution-based hydrothermal growth and a post-growth surface exposure through atomic layer deposition (ALD) to show a dramatic enhancement of the efficiency for water photolysis. These modified photoanodes show a high photocurrent of 3.12â mA cm-2 at 1.23â V versus RHE, (>5 times higher than Fe2 O3 ) and a plateau photocurrent of 4.5â mA cm-2 at 1.5â V versus RHE. We demonstrate that these photoanodes in tandem with a CH3 NH3 PbI3 perovskite solar cell achieves overall unassisted water splitting with an STH conversion efficiency of 3.4 %, constituting a new benchmark for hematite-based tandem systems.
Assuntos
Compostos Férricos/química , Fotólise , Energia Solar , Água/química , Compostos de Cálcio , Eletroquímica/métodos , Óxidos , TitânioRESUMO
Perfect crystals are rare in nature. Real materials often contain crystal defects and chemical order/disorder such as grain boundaries, dislocations, interfaces, surface reconstructions and point defects. Such disruption in periodicity strongly affects material properties and functionality. Despite rapid development of quantitative material characterization methods, correlating three-dimensional (3D) atomic arrangements of chemical order/disorder and crystal defects with material properties remains a challenge. On a parallel front, quantum mechanics calculations such as density functional theory (DFT) have progressed from the modelling of ideal bulk systems to modelling 'real' materials with dopants, dislocations, grain boundaries and interfaces; but these calculations rely heavily on average atomic models extracted from crystallography. To improve the predictive power of first-principles calculations, there is a pressing need to use atomic coordinates of real systems beyond average crystallographic measurements. Here we determine the 3D coordinates of 6,569 iron and 16,627 platinum atoms in an iron-platinum nanoparticle, and correlate chemical order/disorder and crystal defects with material properties at the single-atom level. We identify rich structural variety with unprecedented 3D detail including atomic composition, grain boundaries, anti-phase boundaries, anti-site point defects and swap defects. We show that the experimentally measured coordinates and chemical species with 22 picometre precision can be used as direct input for DFT calculations of material properties such as atomic spin and orbital magnetic moments and local magnetocrystalline anisotropy. This work combines 3D atomic structure determination of crystal defects with DFT calculations, which is expected to advance our understanding of structure-property relationships at the fundamental level.
RESUMO
Electron tomography in materials science has flourished with the demand to characterize nanoscale materials in three dimensions (3D). Access to experimental data is vital for developing and validating reconstruction methods that improve resolution and reduce radiation dose requirements. This work presents five high-quality scanning transmission electron microscope (STEM) tomography datasets in order to address the critical need for open access data in this field. The datasets represent the current limits of experimental technique, are of high quality, and contain materials with structural complexity. Included are tomographic series of a hyperbranched Co2P nanocrystal, platinum nanoparticles on a carbon nanofibre imaged over the complete 180° tilt range, a platinum nanoparticle and a tungsten needle both imaged at atomic resolution by equal slope tomography, and a through-focal tilt series of PtCu nanoparticles. A volumetric reconstruction from every dataset is provided for comparison and development of post-processing and visualization techniques. Researchers interested in creating novel data processing and reconstruction algorithms will now have access to state of the art experimental test data.
Assuntos
Tomografia com Microscopia Eletrônica , Microscopia Eletrônica de Transmissão e Varredura , Algoritmos , Microscopia Crioeletrônica , Processamento de Imagem Assistida por Computador , Imageamento Tridimensional , Microscopia Eletrônica , Microscopia Eletrônica de Varredura , Microscopia Eletrônica de Transmissão , Nanopartículas , Nanoestruturas , Tomografia , Tomografia por Raios X , Tomografia Computadorizada por Raios XRESUMO
OBJECTIVES: To compare the PathVysion fluorescence in-situ hybridisation assay with the INFORM HER2 Dual in-situ hybridisation assay on 104 invasive breast cancers with a broad spectrum of immunohistochemistry scores. METHODS: This case series involved consecutive patients diagnosed with invasive breast carcinoma with equivocal immunohistochemistry score and referred for further HER2 assessment from the departments of Surgery and/or Clinical Oncology of the two hospitals between January 2013 and February 2014. An additional 10 cases with negative HER2 immunohistochemistry and 11 cases with positive HER2 immunohistochemistry were further included. RESULTS: The results of both fluorescence in-situ hybridisation and dual in-situ hybridisation were available in 99 of 104 cases, respectively. Student'st test showed no statistically significant difference in the mean number of HER2 count, CEP17 copies, or HER2/CEP17 ratio between that obtained by fluorescence in-situ hybridisation and that obtained by dual in-situ hybridisation. Pearson's correlation of results for the two assays was strong for HER2/CEP17 signal ratio (R=0.963, P<0.001) and mean HER2 copies per nucleus (R=0.897, P<0.001). Overall agreement was 96.0% (95 out of 99 cases, ĸ0.882). Three of the four discordant cases were equivocal for either fluorescence in-situ hybridisation or dual in-situ hybridisation. The results of immunohistochemistry 0/1+ and 3+ cases showed 100% concordance between the two assays. The failure rate was 0.96% for fluorescence in-situ hybridisation and 3.85% for dual in-situ hybridisation. Cases that failed for fluorescence in-situ hybridisation were successful for dual in-situ hybridisation and vice versa. CONCLUSIONS: Our study showed that dual in-situ hybridisation is a reliable and useful option for HER2 testing in breast cancer.
Assuntos
Neoplasias da Mama/patologia , Hibridização in Situ Fluorescente/métodos , Hibridização In Situ/métodos , Receptor ErbB-2/genética , Neoplasias da Mama/genética , Feminino , Amplificação de Genes , Hong Kong , Humanos , Imuno-Histoquímica , Invasividade Neoplásica , Reprodutibilidade dos Testes , Estudos RetrospectivosRESUMO
Crystallography, the primary method for determining the 3D atomic positions in crystals, has been fundamental to the development of many fields of science. However, the atomic positions obtained from crystallography represent a global average of many unit cells in a crystal. Here, we report, for the first time, the determination of the 3D coordinates of thousands of individual atoms and a point defect in a material by electron tomography with a precision of â¼19 pm, where the crystallinity of the material is not assumed. From the coordinates of these individual atoms, we measure the atomic displacement field and the full strain tensor with a 3D resolution of â¼1 nm(3) and a precision of â¼10(-3), which are further verified by density functional theory calculations and molecular dynamics simulations. The ability to precisely localize the 3D coordinates of individual atoms in materials without assuming crystallinity is expected to find important applications in materials science, nanoscience, physics, chemistry and biology.
Assuntos
Tomografia com Microscopia Eletrônica/métodos , Imageamento Tridimensional/métodos , Modelos TeóricosRESUMO
The accelerator based Boron Neutron Capture Therapy beam at the University of Birmingham is based around a solid thick lithium target cooled by heavy water. Significant upgrades to Birmingham's Dynamitron accelerator are planned prior to commencing a clinical trial. These upgrades will result in an increase in maximum achievable beam current to at least 3 mA. Various upgrades to the target cooling system to cope with this increased power have been investigated. Tests of a phase change coolant known as "binary ice" have been carried out using an induction heater to provide a comparable power input to the Dynamitron beam. The experimental data shows no improvement over chilled water in the submerged jet system, with both systems exhibiting the same heat input to target temperature relation for a given flow rate. The relationship between the cooling circuit pumping rate and the target temperature in the submerged jet system has also been tested.
RESUMO
This paper presents the design and operation characteristics of a solid-state high voltage pulse generator. Its primary utilization is aimed at triggering a gaseous spark gap with high repeatability. Specifically, the trigger generator is designed to achieve a risetime on the order of 0.1 kV/ns to trigger the first stage, trigatron spark gap of a 10-stage, 500 kV Marx generator. The major design components are comprised of a 60 W constant current DC-DC converter for high voltage charging, a single 4 kV thyristor, a step-up pulse transformer, and magnetic switch for pulse steepening. A risetime of <30 ns and pulse magnitude of 4 kV is achieved matching the simulated performance of the design.
RESUMO
We evaluated the effect of Aurora kinase inhibitors AZD1152 and VX680 on canine osteosarcoma cells. Cytotoxicity was seen in all four cell lines; however, half-maximal inhibitory concentrations were significantly higher than in human leukaemia and canine lymphoma cells. AZD1152 reduced Aurora kinase B phosphorylation, indicating resistance was not because of failure of target recognition. Efflux mediated by ABCB1 and ABCG2 transporters is one known mechanism of resistance against these drugs and verapamil enhanced AZD1152-induced apoptosis; however, these transporters were only expressed by a small percentage of cells in each line and the effects of verapamil were modest, suggesting other mechanisms contribute to resistance. Our results indicate that canine osteosarcoma cells are resistant to Aurora kinase inhibitors and suggest that these compounds are unlikely to be useful as single agents for this disease. Further investigation of these resistance mechanisms and the potential utility of Aurora kinase inhibitors in multi-agent protocols is warranted.
Assuntos
Antineoplásicos/farmacologia , Aurora Quinases/antagonistas & inibidores , Doenças do Cão/metabolismo , Resistencia a Medicamentos Antineoplásicos , Osteossarcoma/tratamento farmacológico , Transportadores de Cassetes de Ligação de ATP/genética , Transportadores de Cassetes de Ligação de ATP/metabolismo , Animais , Apoptose , Linhagem Celular Tumoral , Sobrevivência Celular , Cães , Regulação Neoplásica da Expressão Gênica/efeitos dos fármacos , FosforilaçãoRESUMO
Dislocations and their interactions strongly influence many material properties, ranging from the strength of metals and alloys to the efficiency of light-emitting diodes and laser diodes. Several experimental methods can be used to visualize dislocations. Transmission electron microscopy (TEM) has long been used to image dislocations in materials, and high-resolution electron microscopy can reveal dislocation core structures in high detail, particularly in annular dark-field mode. A TEM image, however, represents a two-dimensional projection of a three-dimensional (3D) object (although stereo TEM provides limited information about 3D dislocations). X-ray topography can image dislocations in three dimensions, but with reduced resolution. Using weak-beam dark-field TEM and scanning TEM, electron tomography has been used to image 3D dislocations at a resolution of about five nanometres (refs 15, 16). Atom probe tomography can offer higher-resolution 3D characterization of dislocations, but requires needle-shaped samples and can detect only about 60 per cent of the atoms in a sample. Here we report 3D imaging of dislocations in materials at atomic resolution by electron tomography. By applying 3D Fourier filtering together with equal-slope tomographic reconstruction, we observe nearly all the atoms in a multiply twinned platinum nanoparticle. We observed atomic steps at 3D twin boundaries and imaged the 3D core structure of edge and screw dislocations at atomic resolution. These dislocations and the atomic steps at the twin boundaries, which appear to be stress-relief mechanisms, are not visible in conventional two-dimensional projections. The ability to image 3D disordered structures such as dislocations at atomic resolution is expected to find applications in materials science, nanoscience, solid-state physics and chemistry.
RESUMO
We performed genomewide gene expression analysis of 35 samples representing 6 common histologic subtypes of canine lymphoma and bioinformatics analyses to define their molecular characteristics. Three major groups were defined on the basis of gene expression profiles: (1) low-grade T-cell lymphoma, composed entirely by T-zone lymphoma; (2) high-grade T-cell lymphoma, consisting of lymphoblastic T-cell lymphoma and peripheral T-cell lymphoma not otherwise specified; and (3) B-cell lymphoma, consisting of marginal B-cell lymphoma, diffuse large B-cell lymphoma, and Burkitt lymphoma. Interspecies comparative analyses of gene expression profiles also showed that marginal B-cell lymphoma and diffuse large B-cell lymphoma in dogs and humans might represent a continuum of disease with similar drivers. The classification of these diverse tumors into 3 subgroups was prognostically significant, as the groups were directly correlated with event-free survival. Finally, we developed a benchtop diagnostic test based on expression of 4 genes that can robustly classify canine lymphomas into one of these 3 subgroups, enabling a direct clinical application for our results.
Assuntos
Biomarcadores Tumorais/metabolismo , Doenças do Cão/classificação , Linfoma de Células B/veterinária , Linfoma de Células T/veterinária , Animais , Estudos de Coortes , Biologia Computacional , Intervalo Livre de Doença , Doenças do Cão/mortalidade , Doenças do Cão/patologia , Cães , Feminino , Perfilação da Expressão Gênica , Regulação Neoplásica da Expressão Gênica , Estudo de Associação Genômica Ampla/veterinária , Imunofenotipagem , Linfoma de Células B/classificação , Linfoma de Células B/metabolismo , Linfoma de Células B/patologia , Linfoma de Células T/classificação , Linfoma de Células T/metabolismo , Linfoma de Células T/patologia , Masculino , Análise de Sequência com Séries de Oligonucleotídeos , Prognóstico , RNA Neoplásico/genéticaRESUMO
Lyme disease (LD), caused by the bacterium Borrelia burgdorferi and transmitted in the eastern United States by blacklegged ticks, Ixodes scapularis Say, is classified as nonendemic in Tennessee and surrounding states in the Southeast. Low incidence of LD in these states has been attributed, in part, to vector ticks being scarce or absent; however, tick survey data for many counties are incomplete or out of date. To improve our knowledge of the distribution, abundance, and Borrelia spp. prevalence of I. scapularis, we collected ticks from 1,018 hunter-harvested white-tailed deer (Odocoileus virginianus (Zimmerman)) from 71 of 95 Tennessee counties in fall 2007 and 2008. In total, 160 deer (15.7%) from 35 counties were infested with adult I. scapularis; 30 of these counties were new distributional records for this tick. The mean number of I. scapularis collected per infested deer was 5.4 +/- 0.6 SE. Of the 883 I. scapularis we removed from deer, none were positive for B. burgdorferi and one tested positive for B. miyamotoi. Deer are not reservoir hosts for B. burgdorferi; nevertheless, past surveys in northern LD-endemic states have readily detected B. burgdoreferi in ticks collected from deer. We conclude that I. scapularis is far more widespread in Tennessee than previously reported. The absence of detectable B. burgdorferi infection among these ticks suggests that the LD risk posed by I. scapularis in the surveyed areas of Tennessee is much lower than in LD-endemic areas of the Northeast and upper Midwest.