Wastewater treatment plants elevating microplastic abundances, ecological risks, and loads in Japanese rivers: a source-to-sink perspective.

Little were certain about how wastewater treatment plants (WWTPs) affected the Japanese riverine microplastic contamination. This study explored the influences of WWTPs on microplastic pollution, assessed ecological risks, and looked at the sources-to-sinks phenomenon (WWTPs-to-rivers-to-marine) in riverine settings in Japan's Yamaguchi prefecture. Fifty surface water samples from the five selected rivers (Koya, Saba, Shimaji, and Fushino, Nishiki) and 11 effluent samples from WWTPs in the rivers' catchment were examined. Microplastics were analyzed using filtration, wet-peroxidation, density-separation, and attenuated reflectance-Fourier transform infrared spectroscopy techniques. Results suggested that the less populated and rural river (Nishiki) was less contaminated compared to the WWTPs and urban areas affected rivers (Koya, Saba, Shimaji, and Fushino). The WWTPs increased microplastic abundance twofold in the downstream regions compared to upstream stations. Microplastic characterization showed that the smaller microplastics < 500 µm, fiber-shaped, transparent, blue, and green color particles were major. Polymer identification demonstrated that the polyethylene, polypropylene, and polyethylene terephthalate were prevalent both for the rivers and WWTP effluents. There was a significant emission of microplastics from WWTPs to rivers (4.671 billion pieces per day; 71.8 kg per day) and rivers to Seto Inland Sea (0.13/billion pieces per day/km2; 7.1 kg per day). The per capita MP emissions to the rivers via WWTPs ranged from 0.02 to 6.49 g per day, which was approximately 2% of per capita single-use plastic wastes in Japan. An assessment of ecological risks showed that the WWTPs posed high ecological risks to rivers, and built up the pollution hotspots to their downstream areas by releasing higher number of microplastics and highly toxic polymers. Overall, the WWTPs influenced the rivers through both abundances and characteristics (shapes-size-color-polymers), increased the complexity of microplastic compositions as well as elevated ecological risks in the rivers. This study contributed to bridging the knowledge gaps about microplastic sources-to-sinks, ecological risks, and pollution management in Japan and beyond.

Abundance, characteristics, and ecological risks of microplastics in the riverbed sediments around Dhaka city.

Microplastic (MP) pollution has become an escalating problem in Bangladesh due to its rapid urbanization, economic growth, and excessive use of plastics; however, data on MP pollution from fresh water resources in this country are limited. This study investigated microplastics pollution in riverbed sediments in the peripheral rivers of Dhaka, the capital of Bangladesh. Twenty-eight sediment samples were collected from the selected stations of the Buriganga, Turag, and Balu Rivers. Density separation and wet-peroxidation methods were employed to extract MP particles. Attenuated total reflectance-Fourier transform infrared spectroscopy was used to identify the polymers. The results indicated a medium-level abundance of MPs in riverbed sediment in comparison with the findings of other studies in freshwater sediments worldwide. Film shape, white and transparent color, and large-size (1-5 mm) MPs were dominant in the riverbed sediment. The most abundant polymers were polyethylene (PE), polypropylene (PP), and polyethylene terephthalate (PET). Pollution load index (PLI) values greater than 1 were observed, indicating that all sampling sites were polluted with MPs. An assessment of ecological risks, using the abundance, polymer types, and toxicity of MPs in the sediment samples, suggested a medium to very high ecological risk of MP pollution of the rivers. The increased abundance of MPs and the presence of highly hazardous polymers, namely; polyurethane, acrylonitrile butadiene styrene, polyvinyl chloride, epoxy resin, and polyphenylene sulfide, were associated with higher ecological risks. Scanning electron microscopy (SEM) analysis indicated that the MPs were subjected to weathering actions, reducing the size of MPs, which caused additional potential ecological hazards in these river ecosystems. This investigation provides baseline information on MP pollution in riverine freshwater ecosystems for further in-depth studies of risk assessment and developing strategies for controlling MP pollution in Bangladesh.

Microplastics in the sediments of small-scale Japanese rivers: Abundance and distribution, characterization, sources-to-sink, and ecological risks.

Microplastic pollution in small-scale river sediments remains mostly unknown. This study explored microplastics in the sediments of four small-scale Japanese rivers in Yamaguchi Prefecture: the Awano, Ayaragi, Asa, and Majime. Sediment samples (n = 23) were collected from the selected stations. Density separation and wet peroxidation methods were applied to extract microplastics. Polymers were detected through attenuated total reflectance-Fourier transform infrared spectroscopy. Microplastic abundance indicated relatively moderate values in the small-scale Japanese rivers compared to other rivers around the world. Large microplastics (1-5 mm) in size, fragments in shape, and high-density particles of diverse polymers dominated. Polyvinyl chloride, polyethylene, and polypropylene were the major polymers. The polymers-polyvinyl chloride, polymethylmethacrylate, polyurethane, fluorinated ethylene propylene, and polybutylene in sediments were distinct from those detected in surface water, as were the predominance of large-size (1-5 mm) and fragment-shape microplastics. In contrast to surface water, sediments preserved both common and distinctive microplastics. Thus, the riverine sediment compartment acted as microplastic sink. Scanning electron microscopic (SEM) analysis suggested the presence of weathered microplastics in sediments. Energy dispersive X-ray spectroscopic analysis (EDX) revealed metal contaminants on the microplastic surfaces, indicating synergistic hazard potentials in the riverine ecosystems. Ecological risk assessment results suggested low to very high risks of microplastic pollution for the rivers. The higher abundances of microplastics and highly toxic polymers contributed to the elevated ecological risks. Polyvinyl chloride, acrylonitrile butadiene styrene, polyurethane, and polymethylmethacrylate were the detected highly toxic polymers. The urban and residential areas affected stations ranked high to very high ecological risks. The sites posing very high ecological risks were regarded as pollution hotspots. Overall, this study developed new insights into microplastic pollution in the small-scale rivers and ecological risks for riverine environments, as well as providing a baseline for more comprehensive risk assessments and developing pollution control and management strategies.

Assessing small-scale freshwater microplastics pollution, land-use, source-to-sink conduits, and pollution risks: Perspectives from Japanese rivers polluted with microplastics.

Rivers are vital for understanding freshwater microplastics pollution, along with the conduits from land-sources to marine-sinks. In this study, we investigated microplastics in the small-scale Awano and Ayaragi rivers, which flow into the Sea of Japan (SJ), and the Asa and Majime rivers, which flow into the Seto Inland Sea (SIS) in Yamaguchi Prefecture, Japan. Surface water samples were collected from 29 stations. Filtration, wet peroxidation, and density separation methods were employed to extract microplastics. Polymers were identified via attenuated total reflectance-Fourier transform infrared spectroscopy. Microplastics abundances and comparisons among different rivers revealed that these small-scale rivers were highly polluted than others around the world. Characterization demonstrated that small microplastics (<1000 µm) in size, fibers and fragments in shape and the polymers-polyethylene, polypropylene, vinylon, polyethylene terephthalate, and polystyrene were dominant. These small-scale rivers emitted substantially higher quantities of Japan land-sourced microplastics (0.4-154.27 billions/day and 0.01-17.55 tons/day) into the SJ and SIS environments than larger rivers in other countries compared to basin areas. The pollution load index indicated that all the river stations were polluted with microplastics. An assessment of the polymeric and pollution risks revealed variably low to high risks. The higher were the abundances of microplastics and toxic polymers, the higher were the pollution level and risks. The sites at high risk of pollution were regarded as hotspots. Both point and non-point land-uses sources of pollution could release microplastics into the river freshwater environments, affected posing high risks and hotspots. Moreover, the pollution characteristics (shapes-sizes-polymers) indicated serious ecotoxicological threats to these rivers and their downstream environments. This study provided new insights into river microplastics pollution and revealed small-scale rivers to be prominent source-to-sink microplastics conduits. Risk assessments provided a baseline for future comprehensive assessments and developing practical approaches to wards setting water quality criteria, pollution control and management.

Fish habitat evaluation based on width-to-depth ratio and eco-environmental diversity index in small rivers.

We estimated the performance of river fish habitat evaluation using width-to-depth ratio (WDR) in comparison with eco-environmental diversity (EED) to propose an inexpensive and easy-to-use habitat evaluation procedure, which is applicable to small river construction works. WDR calculation costs less than that of EED. For verification, 25 stations in eight rivers were selected and fish were captured using electrofishing. pH, electrical conductivity, turbidity, dissolved oxygen (DO), water temperature, fraction of forest, farmland, and residential area in each basin were measured to examine possible influence of water quality. Results show that there is no major water quality issue in the target rivers. Although fish habitat is classified as good when WDR is higher than 6, it cannot be evaluated by WDR when it is lower than 6. EED has positive relationship with fish habitat for any WDR value. Thus, if a river geometry design in a river work results in WDR higher than 6, no measures need to be taken regarding fish habitat condition; however, if it is less than 6, it is necessary to examine whether the construction work lowers the EED or not.

Influence of water-film-forming-unit on the enhanced removal of carbon dioxide from mixed gas using water absorption apparatus.

This research uses tap water to absorb carbon dioxide from mixed gas (N2 and CO2) in an absorption apparatus coupled with a water-film-forming-unit (WFFU). The objective is to assess the benefits of using a WFFU to enhance CO2 removal efficiency at low pressure conditions. Based on our results, the WFFU significantly improves CO2 capture at 0.30 MPa in a water absorption system with two WFFUs. The CO2 removal efficiency was 20% greater than for systems without WFFUs. Moreover, statistical data attained by the Taguchi analysis method showed that the number of WFFUs used in the absorption system has the greatest influence on CO2 removal efficiency (contribution percentage = 50.65%) compared to gas pressure, initial CO2 concentration, gas-to-liquid ratio, and liquid temperature. We also thoroughly investigated the effects of these factors on CO2 removal performance. The optimum conditions for CO2 removal efficiency in a system equipped with two WFFUs are low temperature, low gas-to-liquid ratio, low gas pressure (0.25-0.30 MPa), and high inlet CO2 concentration. These findings could provide an effective method for capturing CO2 from exhaust gases, and thus help mitigate global warming.

Response surface method for modeling the removal of carbon dioxide from a simulated gas using water absorption enhanced with a liquid-film-forming device.

This paper presents the results from using a physical absorption process to absorb gaseous CO2 mixed with N2 using water by producing tiny bubbles via a liquid-film-forming device (LFFD) that improves the solubility of CO2 in water. The influence of various parameters-pressure, initial CO2 concentration, gas-to-liquid ratios, and temperature-on the CO2 removal efficiency and its absorption rate in water were investigated and estimated thoroughly by statistical polynomial models obtained by the utilization of the response surface method (RSM) with a central composite design (CCD). Based on the analysis, a high efficiency of CO2 capture can be reached in conditions such as low pressure, high CO2 concentration at the inlet, low gas/liquid ratio, and low temperature. For instance, the highest removal efficiency in the RSM-CCD experimental matrix of nearly 80% occurred for run number 20, which was conducted at 0.30MPa, CO2 concentration of 35%, gas/liquid ratio of 0.71, and temperature of 15°C. Furthermore, the coefficients of determination, R2, were 0.996 for the removal rate and 0.982 for the absorption rate, implying that the predicted values computed by the constructed models correlate strongly and fit well with the experimental values. The results obtained provide essential information for implementing this method properly and effectively and contribute a promising approach to the problem of CO2 capture in air pollution treatment.

Synergistic effect of pressurized carbon dioxide and sodium hypochlorite on the inactivation of Enterococcus sp. in seawater.

This study investigated the effect of combined treatments using pressurized carbon dioxide (PCD) and sodium hypochlorite (NaOCl) on the inactivation of Enterococcus sp. in artificial seawater. Bacterial inactivation was conducted in a liquid-film-forming apparatus with various pressure conditions, CO2 supply rates, and chlorine dosages. Combined PCD/chlorine treatments resulted in greater disinfection efficiency than those for the two individual treatments. Synergy values were correlated with pressure and CO2 concentrations (p < 0.001). Combination of 0.9 MPa PCD (various CO2 supply rates: 25% CO2 + 75% N2, 50% CO2 + 50% N2, and 100% CO2) and chlorine (0.20 mg L-1) yielded average synergy values of 4.9, 5.2, and 4.4 log, respectively, within 3 min. Combined treatment with PCD (100% CO2, 0.3 MPa, and 20 °C) and chlorine (0.20-0.22 mg L-1) achieved an average synergy value of 4.6 log and complete inactivation (5.2-5.5 log reductions) of Enterococcus sp. within 4 min. In contrast, when the two individual treatments (PCD and chlorine) were used, only 3.7 and 1.8-2.3 log reductions, respectively, were achieved after 25 min. These findings suggest that the combined PCD/chlorine treatment has synergistic benefits and provides a promising method for the disinfection of ballast water.

Effects of pressure and pressure cycling on disinfection of Enterococcus sp. in seawater using pressurized carbon dioxide with different content rates.

Interest is growing in a disinfection technique for water treatment without disinfection byproducts. This study presents the result of using a liquid-film-forming apparatus at less than 1.0 MPa for disinfection of seawater. The sensitivity of Enterococcus sp. (ATCC 202155) to the pressurized carbon dioxide (CO2) was examined under various conditions of pressure cycling, pressure, working volume ratio (WVR), and CO2 content rate. The key influences on frequency and magnitude of pressure cycling in enhancing Enterococcus sp. inactivation are elucidated. The results reveal strong correlation between pressure cycling and inactivation efficiency (P-value < 0.001). The outcome of linear regression model analysis suggests that the model can explain 93%, 85%, and 89% of the inactivation efficiency of (25% CO2 + 75% N2), (50% CO2 + 50% N2), and 100% CO2, respectively. The predicted value was fit with experimental results (p-value <0.05). Under identical treatment conditions (pressure = 0.9 MPa, ΔP = 0.14 MPa, 70% WVR, and 20 ± 1°C), treatment with pressurized CO2 (100% purity) resulted in complete inactivation 5.2 log of Enterococcus sp. after 70 cycles within 20 min. The Enterococcus sp. inactivation of pressurized CO2 followed first-order reaction kinetics. The smallest D-value (largest k-value) was induced by pressurized CO2 (100% purity) at 0.9 MPa, which was obtained at 3.85 min (0.5988 min(-1), R(2) ≥ 0.95). The findings could provide an effective method for enhanced bactericidal performance of pressurized CO2, to address recently emerging problems in water disinfection.

Potential bioremediation of mercury-contaminated substrate using filamentous fungi isolated from forest soil.

The use of filamentous fungi in bioremediation of heavy metal contamination has been developed recently. This research aims to observe the capability of filamentous fungi isolated from forest soil for bioremediation of mercury contamination in a substrate. Six fungal strains were selected based on their capability to grow in 25 mg/L Hg(2+)-contaminated potato dextrose agar plates. Fungal strain KRP1 showed the highest ratio of growth diameter, 0.831, thus was chosen for further observation. Identification based on colony and cell morphology carried out by 18S rRNA analysis gave a 98% match to Aspergillus flavus strain KRP1. The fungal characteristics in mercury(II) contamination such as range of optimum pH, optimum temperature and tolerance level were 5.5-7 and 25-35°C and 100 mg/L respectively. The concentration of mercury in the media affected fungal growth during lag phases. The capability of the fungal strain to remove the mercury(II) contaminant was evaluated in 100 mL sterile 10 mg/L Hg(2+)-contaminated potato dextrose broth media in 250 mL Erlenmeyer flasks inoculated with 10(8) spore/mL fungal spore suspension and incubation at 30°C for 7 days. The mercury(II) utilization was observed for flasks shaken in a 130 r/min orbital shaker (shaken) and non-shaken flasks (static) treatments. Flasks containing contaminated media with no fungal spores were also provided as control. All treatments were done in triplicate. The strain was able to remove 97.50% and 98.73% mercury from shaken and static systems respectively. A. flavus strain KRP1 seems to have potential use in bioremediation of aqueous substrates containing mercury(II) through a biosorption mechanism.

Inactivation effect of pressurized carbon dioxide on bacteriophage Qß and ΦX174 as a novel disinfectant for water treatment.

The inactivation effects of pressurized CO2 against bacteriophage Qß and ΦX174 were investigated under the pressure of 0.3-0.9 MPa, initial concentration of 10(7)-10(9) PFU/mL, and temperature of 17.8°C-27.2°C. The optimum conditions were found to be 0.7 MPa and an exposure time of 25 min. Under identical treatment conditions, a greater than 3.3-log reduction in bacteriophage Qß was achieved by CO2, while a nearly 3.0 log reduction was observed for phage ΦX174. The viricidal effects of N2O (an inactivation gas with similar characteristics to CO2), normal acid (HCl), and CO2 treatment with phosphate buffered saline affirmed the chemical nature of CO2 treatment. The pumping cycle, depressurization rate, and release of intracellular substances caused by CO2 were its viricidal mechanisms. The results indicate that CO2 has the potential for use as a disinfectant without forming disinfection by-products.

Delignification of disposable wooden chopsticks waste for fermentative hydrogen production by an enriched culture from a hot spring.

Hydrogen (H2) production from lignocellulosic materials may be enhanced by removing lignin and increasing the porosity of the material prior to enzymatic hydrolysis. Alkaline pretreatment conditions, used to delignify disposable wooden chopsticks (DWC) waste, were investigated. The effects of NaOH concentration, temperature and retention time were examined and it was found that retention time had no effect on lignin removal or carbohydrate released in enzymatic hydrolysate. The highest percentage of lignin removal (41%) was obtained with 2% NaOH at 100°C, correlated with the highest carbohydrate released (67 mg/g pretreated DWC) in the hydrolysate. An enriched culture from a hot spring was used as inoculum for fermentative H2 production, and its optimum initial pH and temperature were determined to be 7.0 and 50°C, respectively. Furthermore, enzymatic hydrolysate from pretreated DWC was successfully demonstrated as a substrate for fermentative H2 production by the enriched culture. The maximum H2 yield and production rate were achieved at 195 mL H2/g total sugars consumed and 116 mL H2/(L·day), respectively.

Effect of different carbon sources on the biological phosphorus removal by a sequencing batch reactor using pressurized pure oxygen.

The effect of different carbon source on the efficiency of enhanced biological phosphorus removal (EBPR) from synthetic wastewater with acetate and two ratios of acetate/starch as a carbon source was investigated. Three pressurized pure oxygen sequencing batch reactor (POSBR) experiments were operated. The reactors (POSBR1, POSBR2 and POSBR3) were developed and studied at different carbon source ratios of 100% acetate, 75% acetate plus 25% starch and 50% acetate plus 50% starch, respectively. The results showed that POSBR1 had a higher phosphate release-to-uptake ratio and, respectively, in a much higher phosphorus removal efficiency (93.8%) than POSBR2 (84.7%) and POSBR3 (77.3%) within 30 days of operation. This indicated that the phosphorus removal efficiency decreased the higher the starch concentration was. It was also found that POSBR1 produced more polyhydroxyalkanoates (PHAs) than the other reactors. Based on the effect of the carbon source on the PHA concentration and consumption, the conditions of POSBR1 were favourable for the growth of polyphosphate-accumulating organisms and therefore, beneficial for the biological phosphorus removal process.

Potable water scarcity: options and issues in the coastal areas of Bangladesh.

In the coastal areas of Bangladesh, scarcity of drinking water is acute as freshwater aquifers are not available at suitable depths and surface water is highly saline. Households are mainly dependent on rainwater harvesting, pond sand filters and pond water for drinking purposes. Thus, individuals in these areas often suffer from waterborne diseases. In this paper, water consumption behaviour in two southwestern coastal districts of Bangladesh has been investigated. The data for this study were collected through a survey conducted on 750 rural households in 39 villages of the study area. The sample was selected using a random sampling technique. Households' choice of water source is complex and seasonally dependent. Water sourcing patterns, households' preference of water sourcing options and economic feasibility of options suggest that a combination of household and community-based options could be suitable for year-round water supply. Distance and time required for water collection were found to be difficult for water collection from community-based options. Both household and community-based options need regular maintenance. In addition to installation of water supply facilities, it is necessary to make the residents aware of proper operation and maintenance of the facilities.

Comparison of disinfection effect of pressurized gases of CO2, N2O, and N2 on Escherichia coli.

Based on the production of gas bubbles with the support of a liquid film-forming apparatus, a device inducing contact between gas and water was used to inactivate pathogens for water disinfection. In this study, the inactivation effect of CO2 against Escherichia coli was investigated and compared with the effects of N2O and N2 under the same pressure (0.3-0.9 MPa), initial concentration, and temperature. The optimum conditions were found to be 0.7 MPa and an exposure time of 25 min. Under identical treatment conditions, a greater than 5.0-log reduction in E. coli was achieved by CO2, while 3.3 log and 2.4 log reductions were observed when N2O and N2 were used, respectively. Observation under scanning electron microscopy and measurement of bacterial cell substances by UV-absorbance revealed greater cell rupture of E. coli following treatment with CO2 than when treatment was conducted using N2O, N2 and untreated water. The physical effects of the pump, acidified characteristics and the release of intracellular substances caused by CO2 were bactericidal mechanism of this process. Overall, the results of this study indicate that CO2 has the disinfection potential without undesired by-product forming.

Excited-state intramolecular proton transfer and charge transfer in 2-(2'-hydroxyphenyl)benzimidazole crystals studied by polymorphs-selected electronic spectroscopy.

Crystal structures of polymorphs of 2-(2'-hydroxyphenyl)benzimidazole (HPBI), Forms α and ß, are analyzed by X-ray crystallography. The fluorescence excitation (FE) and fluorescence spectra of the polymorphs are separately observed at temperatures 77-298 K. It has been found that the electronic spectra of the two crystal forms are significantly different from each other. Photo-excitation of the enol forms in Forms α and ß induces the excited-state intramolecular proton transfer (ESIPT) to produce the S(1) state of the keto forms. In the FE spectra of Forms α and ß, the S(1) ← S(0) (ππ*) transition of the keto form is observed in the 360-420 nm region in addition to that of the enol form in the 250-420 nm region. In the FE spectrum of Form ß a new band peaking at 305 nm is observed, which is assigned to the S(1) ← S(0) transition of a non-planar enol form based on the observation of dual fluorescence in the UV and visible regions and quantum chemical calculation on the transition energy against the twisted angle between the benzimidazole and hydroxyphenyl rings. The fluorescence quantum yield (φ(T)) for the keto form is remarkably dependent on polymorphs at room temperature; φ(T) = 0.53 for Form α is much larger than φ(T) ≤ 0.23 for Form ß. At 77 K the φ(T) values for Forms α and ß increase to 0.67 and ≤0.57, respectively. The changes in the φ(T) values are associated with the intramolecular charge transfer (ICT) state. The potential barrier height between the S(1)-keto and S(1)-ICT states is significantly lower for Form ß than for Form α. At 77 K the S(1)-keto → S(1)-ICT process followed by S(1)-ICT → S(0)-keto internal conversion is significantly suppressed in Form ß. We compare difference in the dynamics between Forms α and ß in the electronic ground and excited states.

Thermal luminescence spectra of polyamides and their Maillard reaction with reducing sugars.

Thermal luminescence (TL) spectra of polyamides were measured with a Fourier-transform chemiluminescence spectrometer to elucidate the emission mechanism. A TL band of ε-polylysine with a peak at 542 nm observed at 403 K was assigned to the emission due to the interaction of the -CO-NH- group with oxygen molecules by comparison with nylon-6, polyglycine, and polyalanine. When the sample was kept at 453 K, the intensity of the TL band decreased and the wavelength of the peak shifted to 602 nm, which was assigned to the emission due to the interaction of the NH2 group on the side chain with oxygen molecules by comparison with monomeric lysine. A weak emission with a peak at 668 nm was assigned to the advanced glycosylation end products (AGEs) yielded by the Maillard reaction with a catalytic amount of water. To understand this reaction and to examine the TL emission of AGEs, we measured TL spectra of mixtures of polylysine and reducing sugars such as glucose, maltose, lactose, and dextrin. The minimum temperature for TL emission, wavelength of the peak and the relative intensities of the TL emission were found to depend on the size of the sugars.

Infrared and electronic spectra of radicals produced from 2-naphthol and carbazole by UV-induced hydrogen-atom eliminations.

The photoreaction mechanisms of 2-naphthol and carbazole in low-temperature argon matrices have been investigated by infrared and electronic absorption spectroscopy with aids of density-functional-theory (DFT) and time-dependent DFT (TD-DFT) calculations. When the matrix samples were irradiated upon UV light, 2-naphthoxyl and N-carbazolyl radicals were produced by the elimination of the H atom in the O-H group of 2-naphthol and in the N-H group of carbazole, respectively. The observed IR and electronic absorption spectra of the radicals were reproduced satisfactorily by the quantum chemical calculations. To understand a role of the radicals in the excited-state proton transfer (ESPT), the fluorescence and excitation spectra of 2-naphthol and carbazole were measured in aqueous solution at room temperature as well as in the low-temperature argon matrices. It was found that the intensity of the fluorescence emitted from carbazole anion in aqueous solution decreased when oxygen gas was blown into the solution.

Characterization of polyhydroxyalkanoates (PHAs) biosynthesis by isolated Novosphingobium sp. THA_AIK7 using crude glycerol.

Biodiesel-contaminated wastewater was used to screen for PHAs-producing bacteria by using crude glycerol as the sole carbon source. A gram-negative THA_AIK7 isolate was chosen as a potential PHAs producer. The 16S rRNA phylogeny indicated that THA_AIK7 isolate is a member of Novosphingobium genus which is supported by a bootstrap percentage of 100% with Novosphingobium capsulatum. The 1,487 bp of 16S rRNA gene sequence of THA_AIK7 isolate has been deposited in the GenBank database under the accession number HM031593. Polymer content of 45% cell dry weight was achieved in 72 h with maximum product yield coefficient of 0.29 g PHAs g⁻¹ glycerol. Transmission electron micrograph results exhibited the PHAs granules accumulated inside the bacterial cell. PHAs polymer production in mineral salt media supplemented with 2% (w/v) of crude glycerol at initial pH 7 was extracted by the sodium hypochlorite method. Polymer film spectrographs from Nuclear magnetic resonance displayed a pattern of signal virtually identical to spectra of commercial PHB. Thermal analysis by Differential scanning calorimeter showed a melting temperature at 179°C. Molecular weight analysis by Gel permeation chromatography showed two main peaks of 133,000 and 700 g mol⁻¹ with weight-average molecular weight value of 23,800 and number-average molecular weight value of 755. Endotoxinfree of PHAs polymer was preliminarily assessed by a negative result of the gel-clot formation, Pyrotell® Single test vial, at sensitivity of 0.25 EU ml⁻¹. To our knowledge, this is the first reported test of endotoxin-free PHAs naturally produced from gram-negative bacteria which could be used for biomedical application.

Bacteriological assessment of drinking water supply options in coastal areas of Bangladesh.

This study was conducted to assess the bacteriological quality of alternative drinking water supply options in southwest coastal areas of Bangladesh. A total of 90 water samples were collected during both dry and wet seasons from household based rainwater harvesting systems (RWHSS), community based rain water harvesting systems (CRWHSs), pond-sand filters (PSFs) and ponds. The samples were evaluated for faecal coliform, Escherichia coli and Heterotrophic Plate Count, as well as Vibrio cholerae, Salmonella spp., Shigella spp. and Pseudomonas spp. Physico-chemical parameters (pH, electrical conductivity, and color) were also examined. In addition, sanitary inspections were conducted to identify faecal contamination sources. All options showed varying degrees of indicator bacterial contamination. The median E. coli concentrations measured for RWHSs, CRWHSS, PSFS, and ponds were 16, 7, 11, and 488 cfu/100 ml during the wet season, respectively. Vibrio cholerae 01/0139, Salmonella and Shigella spp. were not found in any samples. However, Vibrio cholerae Non-01/Non-0139 and Pseudomonas spp. were isolated from 74.4% and 91.1% of the water samples collected during the wet season. A maximum pH of 10.4 was found in CRWHSS. Estimation of the disease burden for all options in disability adjusted life years (DALYs) showed an increased disease burden during the wet season. According to sanitary inspections, poor maintenance and unprotected ponds were responsible for rainwater and PSF water contamination, respectively. The findings of the present study suggest that alternative drinking water supply options available in southwest coastal Bangladesh pose a substantial risk to public health.