Unique Method for Facile Postsynthetic Modification of Nonisocyanate Polyurethanes.

Nonisocyanate polyurethanes (NIPUs) are broadly investigated as a potential replacement for conventional polyurethanes (PUs) to eliminate the use of toxic isocyanates and reduce occupational hazards. One of the most popular approaches to NIPU synthesis is the polyaddition of cyclic bis(carbonate)s and diamines to form poly(hydroxyurethane)s (PHUs). However, such PHUs are highly hydrophilic due to the presence of two hydroxyl groups per repeat unit, and the resulting moisture absorption significantly degrades their thermomechanical performance and physical stability upon exposure to humidity, thus limiting their utility. Here, we introduce a simple and scalable approach for the modification of PHUs to increase hydrophobicity and adjust their properties. The proposed reaction between aldehydes and appropriately spaced hydroxyl groups in the polymer backbone resulted in high degrees of modification (up to 84%) and up to 3-fold reductions in water uptake at 85% RH. Furthermore, the use of aromatic aldehydes in particular enabled the retention of mechanical properties over a wide range of humidity levels, resulting in performance comparable to conventional PUs. Finally, we note that this approach is not limited to reducing moisture sensitivity alone and provides ample opportunities for imparting a broad range of novel properties to PHUs through an appropriate selection of functional aldehydes.

A New Method to Prepare Stable Polyaniline Dispersions for Highly Loaded Cathodes of All-Polymer Li-Ion Batteries.

A new method for the preparation of polyaniline (PANI) films that have a 2D structure and can record high active mass loading (up to 30 mg cm-2) via acid-assisted polymerization in the presence of concentrated formic acid was developed. This new approach represents a simple reaction pathway that proceeds quickly at room temperature in quantitative isolated yield with the absence of any byproducts and leads to the formation of a stable suspension that can be stored for a prolonged time without sedimentation. The observed stability was explained by two factors: (a) the small size of the obtained rod-like particles (50 nm) and (b) the change of the surface of colloidal PANI particles to a positively charged form by protonation with concentrated formic acid. The films cast from the concentrated suspension were composed of amorphous PANI chains assembled into 2D structures with nanofibrillar morphology. Such PANI films demonstrated fast and efficient diffusion of the ions in liquid electrolyte and showed a pair of revisable oxidation and reduction peaks in cyclic voltammetry. Furthermore, owing to the high mass loading, specific morphology, and porosity, the synthesized polyaniline film was impregnated by a single-ion conducting polyelectrolyte-poly(LiMn-r-PEGMm) and characterized as a novel lightweight all-polymeric cathode material for solid-state Li batteries by cyclic voltammetry and electrochemical impedance spectroscopy techniques.

Mechanically Robust Poly(ionic liquid) Block Copolymers as Self-Assembling Gating Materials for Single-Walled Carbon-Nanotube-Based Thin-Film Transistors.

The proliferation of high-performance thin-film electronics depends on the development of highly conductive solid-state polymeric materials. We report on the synthesis and properties investigation of well-defined cationic and anionic poly(ionic liquid) AB-C type block copolymers, where the AB block was formed by random copolymerization of highly conductive anionic or cationic monomers with poly(ethylene glycol) methyl ether methacrylate, while the C block was obtained by post-polymerization of 2-phenylethyl methacrylate. The resulting ionic block copolymers were found to self-assemble into a lamellar morphology, exhibiting high ionic conductivity (up to 3.6 × 10-6 S cm-1 at 25 °C) and sufficient electrochemical stability (up to 3.4 V vs Ag+/Ag at 25 °C) as well as enhanced viscoelastic (mechanical) performance (storage modulus up to 3.8 × 105 Pa). The polymers were then tested as separators in two all-solid-state electrochemical devices: parallel plate metal-insulator-metal (MIM) capacitors and thin-film transistors (TFTs). The laboratory-scale truly solid-state MIM capacitors showed the start of electrical double-layer (EDL) formation at ∼103 Hz and high areal capacitance (up to 17.2 µF cm-2). For solid-state TFTs, low hysteresis was observed at 10 Hz due to the completion of EDL formation and the devices were found to have low threshold voltages of -0.3 and 1.1 V for p-type and n-type operations, respectively.

Tunning CO2 Separation Performance of Ionic Liquids through Asymmetric Anions.

This work aims to explore the gas permeation performance of two newly-designed ionic liquids, [C2mim][CF3BF3] and [C2mim][CF3SO2C(CN)2], in supported ionic liquid membranes (SILM) configuration, as another effort to provide an overall insight on the gas permeation performance of functionalized-ionic liquids with the [C2mim]+ cation. [C2mim][CF3BF3] and [C2mim][CF3SO2C(CN)2] single gas separation performance towards CO2, N2, and CH4 at T = 293 K and T = 308 K were measured using the time-lag method. Assessing the CO2 permeation results, [C2mim][CF3BF3] showed an undermined value of 710 Barrer at 293.15 K and 1 bar of feed pressure when compared to [C2mim][BF4], whereas for the [C2mim][CF3SO2C(CN)2] IL an unexpected CO2 permeability of 1095 Barrer was attained at the same experimental conditions, overcoming the results for the remaining ILs used for comparison. The prepared membranes exhibited diverse permselectivities, varying from 16.9 to 22.2 for CO2/CH4 and 37.0 to 44.4 for CO2/N2 gas pairs. The thermophysical properties of the [C2mim][CF3BF3] and [C2mim][CF3SO2C(CN)2] ILs were also determined in the range of T = 293.15 K up to T = 353.15 K at atmospheric pressure and compared with those for other ILs with the same cation and anion's with similar chemical moieties.

Structure conformation, physicochemical and rheological properties of flaxseed gums extracted under alkaline and acidic conditions.

The present work aimed at investigating an extraction protocol based on consecutive steps of isoelectric point (pH ~ 4.25) mediated gum swelling and deproteinisation as an alternative method to produce flaxseed gum extracts of enhanced techno-functional characteristics. The osidic and proximate composition, structure conformation, flow behaviour, dynamic rheological and thermal properties of gums isolated from brown and golden flaxseeds were assessed. Gum extraction under near-to-isoelectric point conditions did not impair the extraction yield, residual protein and ash content, whilst it resulted in minor changes in the sugar composition of the flaxseed gum extracts. The deconvolution of the GPC/SEC chromatographs revealed the presence of four major polysaccharidic populations corresponding to arabinoxylans, rhamnogalacturonan-I and two AX-RG-I composite fractions. The latter appeared to minimise the intra- and interchain polymer non-covalent interactions (hydrogen bonding) leading to a better solvation affinity in water and lyotropic solvents. Golden flaxseed gums exerted higher molecular weight (Mw = 1.34-1.15 × 106 Da) and intrinsic viscosities (6.63-5.13 dL g-1) as well as better thickening and viscoelastic performance than the brown flaxseed gum exemplars. Golden flaxseed gums exhibited a better thermal stability compared to the brown flaxseed counterparts and therefore, they are suitable for product applications involving severe heat treatments.

Unique Carbonate-Based Single Ion Conducting Block Copolymers Enabling High-Voltage, All-Solid-State Lithium Metal Batteries.

Safety and high-voltage operation are key metrics for advanced, solid-state energy storage devices to power low- or zero-emission HEV or EV vehicles. In this study, we propose the modification of single-ion conducting polyelectrolytes by designing novel block copolymers, which combine one block responsible for high ionic conductivity and the second block for improved mechanical properties and outstanding electrochemical stability. To synthesize such block copolymers, the ring opening polymerization (ROP) of trimethylene carbonate (TMC) monomer by the RAFT-agent having a terminal hydroxyl group is used. It allows for the preparation of a poly(carbonate) macro-RAFT precursor that is subsequently applied in RAFT copolymerization of lithium 1-[3-(methacryloyloxy)propylsulfonyl]-1-(trifluoromethylsulfonyl)imide and poly(ethylene glycol) methyl ether methacrylate. The resulting single-ion conducting block copolymers show improved viscoelastic properties, good thermal stability (T onset up to 155 °C), sufficient ionic conductivity (up to 3.7 × 10-6 S cm-1 at 70 °C), and high lithium-ion transference number (0.91) to enable high power. Excellent plating/stripping ability with resistance to dendrite growth and outstanding electrochemical stability window (exceeding 4.8 V vs Li+/Li at 70 °C) are also achieved, along with enhanced compatibility with composite cathodes, both LiNiMnCoO2 - NMC and LiFePO4 - LFP, as well as the lithium metal anode. Lab-scale truly solid-state Li/LFP and Li/NMC lithium-metal cells assembled with the single-ion copolymer electrolyte demonstrate reversible and very stable cycling at 70 °C delivering high specific capacity (up to 145 and 118 mAh g-1, respectively, at a C/20 rate) and proper operation even at a higher current regime. Remarkably, the addition of a little amount of propylene carbonate (∼8 wt %) allows for stable, highly reversible cycling at a higher C-rate. These results represent an excellent achievement for a truly single-ion conducting solid-state polymer electrolyte, placing the obtained ionic block copolymers on top of polyelectrolytes with highest electrochemical stability and potentially enabling safe, practical Li-metal cells operating at high-voltage.

Reinforcement of Styrene Butadiene Rubber Employing Poly(isobornyl methacrylate) (PIBOMA) as High Tg Thermoplastic Polymer.

A set of poly(isobornyl methacrylate)s (PIBOMA) having molar mass in the range of 26,000-283,000 g mol-1 was prepared either via RAFT process or using free radical polymerization. These linear polymers demonstrated high glass transition temperatures (Tg up to 201 °C) and thermal stability (Tonset up to 230 °C). They were further applied as reinforcing agents in the preparation of the vulcanized rubber compositions based on poly(styrene butadiene rubber) (SBR). The influence of the PIBOMA content and molar mass on the cure characteristics, rheological and mechanical properties of rubber compounds were studied in detail. Moving die rheometry revealed that all rubber compounds filled with PIBOMA demonstrated higher torque increase values ΔS in comparison with rubber compositions without filler, independent of PIBOMA content or molar mass, thus confirming its reinforcing effect. Reinforcement via PIBOMA addition was also observed for vulcanized rubbers in the viscoelastic region and the rubbery plateau, i.e. from -20 to 180 °C, by dynamic mechanical thermal analysis. Notably, while at temperatures above ~125 °C, ultra-high-molecular-weight polyethylene (UHMWPE) rapidly loses its ability to provide reinforcement due to softening/melting, all PIBOMA resins maintained their ability to reinforce rubber matrix up to 180 °C. For rubber compositions containing 20 phr of PIBOMA, both tensile strength and elongation at break decreased with increasing PIBOMA molecular weight. In summary, PIBOMA, with its outstanding high Tg among known poly(methacrylates), may be used in the preparation of advanced high-stiffness rubber compositions, where it provides reinforcement above 120 °C and gives properties appropriate for a range of applications.

Cryotropic gel-forming capacity of alfalfa (Medicago sativa L.) and fenugreek (Trigonella foenum graecum) seed galactomannans.

Cryotropic gelation is one of the most common approaches to design novel hydrogels with multifaceted technological and biological functionalities. In the present paper, we studied the ability of highly galactosyl-substituted galactomannans, i.e. fenugreek and alfalfa gum, to form physically crosslinked hydrogels via cryogenic processing. Cycling of the galactomannan solutions (0.25 to 4% wt) from 25 to -20 to 25 °C induced the physical crosslinking of the galactomannan chains leading to the formation of different cryogel structures, i.e. filamentous aggregates (c* < c < 1%), cellular-like gel networks (1 ≤ c < 4%) or a homogeneously swollen gel (c ≥ 4%), depending on the total biopolymer content. Alfalfa gum-based cryogels exhibited higher elasticity and stiffness, better uniformity of the structure and a lower macropore size than their fenugreek counterparts. The physical blending of alfalfa or fenugreek gum with locust bean gum (2% total biopolymer) led to the reinforcement of the mechanical properties of the cryogels without significantly altering their microstructural aspects.

Structure conformational and rheological characterisation of alfalfa seed (Medicago sativa L.) galactomannan.

In the present work a galactomannan extract of low protein residue (< 1.3 % wt dry basis) was isolated from alfalfa (Medicago sativa L.) seed endosperm meal. The alfalfa gum (AAG) comprised primarily mannose and galactose at a ratio of 1.18:1, had a molecular weight of 2 × 106 Da and a radius of gyration of 48.7 nm. The average intrinsic viscosity of the dilute AAG dispersions calculated using the modified Mark-Houwink, Huggins and Kraemer equations was 9.33 dLg-1 at 25 °C. The critical overlap concentration was estimated at 0.306 % whereas the concentration dependence of specific viscosity for the dilute and semi-dilute regimes was ∝ C2.3 and C4.2, respectively. The compliance to the Cox-Merz rule was satisfied at 1% of AAG, whereas a departure from superimposition was observed at higher concentrations. Viscoelasticity measurements demonstrated that AAG dispersions exhibit a predominant viscous character at 1 % wt, whereas a weak gel-like behaviour was reached at AAG concentrations ≥3 %.

Tuning the miscibility of water in imide-based ionic liquids.

Liquid-liquid phase behavior measurements were performed for binary mixtures of water and ionic liquids (ILs) containing the same 1-ethyl-3-methylimidazolium ([C2mim]+) cation and different imide-based anions, having symmetric (bis(fluorosulfonyl)imide ([FSI]-)) or asymmetric structures (2,2,2-trifluoromethylsulfonyl-N-cyanoamide ([TFSAM]-) and 2,2,2-trifluoro-N-(trifluoromethylsulfonyl)acetamide ([TSAC]-)). An inversion of phase behavior was observed: while below ∼298 K, the miscibility of water in the studied ILs increases according to the order [C2mim][TSAC] < [C2mim][FSI] < [C2mim][NTf2], for temperatures above ∼303 K, the reverse trend is observed [C2mim][NTf2] < [C2mim][FSI] < [C2mim][TSAC]. In turn, above ∼306 K the [C2mim][TFSAM] is completely miscible with H2O in all ranges of concentrations. The obtained results also revealed an unusual water solubility variation of 11% in [C2mim][FSI], and 20% in [C2mim][TSAC], when the system temperature was changed by less than 1 K, around 298 K and 301 K, respectively. Molecular Dynamics (MD) simulations were used to understand the IL-water interactions and rationalize the experimental observations. These results suggested that the miscibility trends are mainly related to the ability of the water molecules to form water-anion and water-water aggregates in solution.

Ionic Polyureas-A Novel Subclass of Poly(Ionic Liquid)s for CO2 Capture.

The growing concern for climate change and global warming has given rise to investigations in various research fields, including one particular area dedicated to the creation of solid sorbents for efficient CO2 capture. In this work, a new family of poly(ionic liquid)s (PILs) comprising cationic polyureas (PURs) with tetrafluoroborate (BF4) anions has been synthesized. Condensation of various diisocyanates with novel ionic diamines and subsequent ion metathesis reaction resulted in high molar mass ionic PURs (Mw = 12 ÷ 173 × 103 g/mol) with high thermal stability (up to 260 °C), glass transition temperatures in the range of 153-286 °C and remarkable CO2 capture (10.5-24.8 mg/g at 0 °C and 1 bar). The CO2 sorption was found to be dependent on the nature of the cation and structure of the diisocyanate. The highest sorption was demonstrated by tetrafluoroborate PUR based on 4,4'-methylene-bis(cyclohexyl isocyanate) diisocyanate and aromatic diamine bearing quinuclidinium cation (24.8 mg/g at 0 °C and 1 bar). It is hoped that the present study will inspire novel design strategies for improving the sorption properties of PILs and the creation of novel effective CO2 sorbents.

Li Coordination of a Novel Asymmetric Anion in Ionic Liquid-in-Li Salt Electrolytes.

We analyze the influence of the asymmetry of the anion on coordination and transport processes in a Li salt/ionic liquid system. The relatively new asymmetric 2,2,2-trifluoromethylsulfonyl-N-cyanamide (TFSAM) anion was investigated in Pyr14TFSAM(1-x)LiTFSAMx over a broad concentration range (up to x = 0.7 Li salt) and was compared to the well-known bis(trifluoromethanesulfonyl)amide (TFSA) anion. In contrast to the TFSA-based system, the system with TFSAM has no phase transition over the whole concentration range. Raman spectroscopy and NMR chemical shifts elucidate the Li coordination in detail. Up to x = 0.3, the asymmetric anion coordinates to Li+ only via the cyano group. With increasing Li salt fraction, the contribution of Li-oxygen coordination increases. This coordination effects influence the transport properties of the system, as examined via pulsed-field-gradient NMR (PFG-NMR). Although the overall diffusivity of both systems is decreasing because of viscosity effects, the relative diffusivity of the Li cation is increasing with x. This suggests a change in the transport mechanism depending on the Li salt fraction. Interestingly, the contribution of structural diffusion at high Li salt concentrations (x ≥ 0.6) seems to be higher in the TFSAM system, influenced by the nonsymmetric coordination, while in the TFSA system, the vehicular transport seems to be still predominant at x ≥ 0.6.

Neat ionic liquids versus ionic liquid mixtures: a combination of experimental data and molecular simulation.

Simple mixtures of ionic liquids (IL-IL mixtures) can become a promising approach for the substitution of task-specific ILs. Such a concept was explored in this article by comparison of the thermophysical properties of neat 1-ethyl-3-methylimidazolium 2,2,2-trifluoromethylsulfonyl-N-cyanoamide, [C2mim][TFSAM], and equimolar mixtures of two structurally similar ILs having more common ions. Molecular dynamics (MD) simulations were additionally used to further highlight structural aspects of these systems at a molecular level.

Exploring the effect of fluorinated anions on the CO2/N2 separation of supported ionic liquid membranes.

The CO2 and N2 permeation properties of ionic liquids (ILs) based on the 1-ethyl-3-methylimidazolium cation ([C2mim]+) and different fluorinated anions, namely 2,2,2-trifluoromethylsulfonyl-N-cyanoamide ([TFSAM]-), bis(fluorosulfonyl) imide ([FSI]-), nonafluorobutanesulfonate ([C4F9SO3]-), tris(pentafluoroethyl)trifluorophosphate ([FAP]-), and bis(pentafluoroethylsulfonyl)imide ([BETI]-) anions, were measured using supported ionic liquid membranes (SILMs). The results show that pure ILs containing [TFSAM]- and [FSI]- anions present the highest CO2 permeabilities, 753 and 843 Barrer, as well as the greatest CO2/N2 permselectivities of 43.9 and 46.1, respectively, with CO2/N2 separation performances on top of or above the Robeson 2008 upper bound. The re-design of the [TFSAM]- anion by structural unfolding was investigated through the use of IL mixtures. The gas transport and CO2/N2 separation properties through a pure [C2mim][TFSAM] SILM are compared to those of two different binary IL mixtures containing fluorinated and cyano-functionalized groups in the anions. Although the use of IL mixtures is a promising strategy to tailor gas permeation through SILMs, the pure [C2mim][TFSAM] SILM displays higher CO2 permeability, diffusivity and solubility than the selected IL mixtures. Nevertheless, both the prepared mixtures present CO2 separation performances that are on top of or above the Robeson plot.

Ionic liquids with anions based on fluorosulfonyl derivatives: from asymmetrical substitutions to a consistent force field model.

Herein, seven anions including four imide-based, namely bis[(trifluoromethyl)sulfonyl]imide (TFSI), bis(fluorosulfonyl)imide (FSI), bis[(pentafluoroethyl)sulfonyl]imide (BETI), 2,2,2-trifluoromethylsulfonyl-N-cyanoamide (TFSAM) and 2,2,2-trifluoro-N-(trifluoromethylsulfonyl) acetamide (TSAC), and two sulfonate anions, trifluoromethanesulfonate (triflate, TF) and nonafluorobutanesulfonate (NF), are considered and compared. The volumetric mass density and dynamic viscosity of five ionic liquids containing these anions combined with the commonly used 1-ethyl-3-methylimidazolium cation (C2C1im), [C2C1im][FSI], [C2C1im][BETI], [C2C1im][TFSAM], [C2C1im][TSAC] and [C2C1im][NF] are measured in the temperature range of 293.15 ≤ T/K ≤ 353.15 and at atmospheric pressure. The results show that [C2mim][FSI] and [C2mim][TFSAM] exhibit the lowest densities and viscosities among all the studied ionic liquids. The experimental volumetric data is used to validate a more consistent re-parameterization of the CL&P force field for use in MD simulations of ionic liquids containing the ubiquitous bis[(trifluoromethyl)sulfonyl]imide and trifluoromethanesulfonate anions and to extend the application of the model to other molten salts with similar ions.

A New Volume-Based Approach for Predicting Thermophysical Behavior of Ionic Liquids and Ionic Liquid Crystals.

Volume-based prediction of melting points and other properties of ionic liquids (ILs) relies on empirical relations with volumes of ions in these low-melting organic salts. Here we report an accurate way to ionic volumes by Bader's partitioning of electron densities from X-ray diffraction obtained via a simple database approach. For a series of 1-tetradecyl-3-methylimidazolium salts, the volumes of different anions are found to correlate linearly with melting points; larger anions giving lower-melting ILs. The volume-based concept is transferred to ionic liquid crystals (ILs that adopt liquid crystalline mesophases, ILCs) for predicting the domain of their existence from the knowledge of their constituents. For 1-alkyl-3-methylimidazolium ILCs, linear correlations of ionic volumes with the occurrence of LC mesophase and its stability are revealed, thus paving the way to rational design of ILCs by combining suitably sized ions.

Single-Ion Block Copoly(ionic liquid)s as Electrolytes for All-Solid State Lithium Batteries.

Polymer electrolytes have been proposed as replacement for conventional liquid electrolytes in lithium-ion batteries (LIBs) due to their intrinsic enhanced safety. Nevertheless, the power delivery of these materials is limited by the concentration gradient of the lithium salt. Single-ion conducting polyelectrolytes represent the ideal solution since their nature prevents polarization phenomena. Herein, the preparation of a new family of single-ion conducting block copolymer polyelectrolytes via reversible addition-fragmentation chain transfer polymerization technique is reported. These copolymers comprise poly(lithium 1-[3-(methacryloyloxy)propylsulfonyl]-1-(trifluoromethylsulfonyl)imide) and poly(ethylene glycol) methyl ether methacrylate blocks. The obtained polyelectrolytes show low Tg values in the range of -61 to 0.6 °C, comparatively high ionic conductivity (up to 2.3 × 10(-6) and 1.2 × 10(-5) S cm(-1) at 25 and 55 °C, respectively), wide electrochemical stability (up to 4.5 V versus Li(+)/Li), and a lithium-ion transference number close to unity (0.83). Owing to the combination of all mentioned properties, the prepared polymer materials were used as solid polyelectrolytes and as binders in the elaboration of lithium-metal battery prototypes with high charge/discharge efficiency and excellent specific capacity (up to 130 mAh g(-1)) at C/15 rate.

A first truly all-solid state organic electrochromic device based on polymeric ionic liquids.

Using polymeric ionic liquids and PEDOT as ion conducting separators and electrodes, respectively, an all-polymer-based organic electrochromic device (ECD) has been constructed. The advantages of such an ECD are: fast switching time (3 s), high coloration efficiency (390 cm(2) C(-1) at 620 nm), optical contrast up to ΔT = 22% and the possibility of working under vacuum.