Evaluation of an automated platelet aggregation method for detection of congenital or acquired platelet function defects.

BACKGROUND: Light transmission aggregometry (LTA) is the most widely used laboratory method for an initial screening of patients with a suspected platelet function defect (PFD), and its use has also been proposed for assessing the efficacy of antiplatelet treatment (APT). An automated LTA method has been developed by Sysmex (Kobe, Japan) on a routine coagulation analyzer (CS-2400), together with a new research parameter called PAL (platelet aggregation level) to evaluate patients on APT. MATERIALS AND METHODS: We evaluated the performance of CS-2400 compared to a stand-alone lumi-dual-aggregometer device in the diagnosis of PFD and in assessing the efficacy of APT. For these purposes, the study population was represented by a cohort of 23 patients with a previous diagnosis of PFD and a cohort of 28 patients on APT. RESULTS: Compared to healthy volunteers, patients with PFD showed a statistically significant reduction (p<0.05) in the maximal %light transmission, irrespective of the agonist used, both with the CS-2400 and the lumi-dual-aggregometer. As regards PFD patients, CS-2400 was effective in identifying the more severe defects, with a good sensibility and specificity, but less effective in identifying milder forms of PFD, such as platelet secretion defects. Patients on APT showed a statistically significant (p=0.001) reduced median %light transmission and PAL scores compared to healthy controls. DISCUSSION: Thanks to this LTA technology, CS-2400, a routine coagulation analyzer widely available in routine laboratories, could prove useful for initial assessment of patients with a suspected PFD. Moreover, the PAL scores were a fairly accurate reflection of the platelet response to APT.

The Validity and Reliability of a Smartphone Application for Break-Point Angle Measurement during Nordic Hamstring Exercise.

Background: A recently developed smartphone application (Nordic Angle) allows the automatic calculation of the break-point angle (BPA) during Nordic hamstring exercise (NHE) without transferring the collected data to a computer. The BPA is the point at which the hamstrings are unable to withstand force. However, the validity of the BPA values obtained by this method has not been examined. Hypothesis/Purpose: This study aimed to evaluate the validity and reliability of the Nordic Angle by comparing the BPA values of the Nordic Angle with those of two-dimensional motion analysis software that can calculate the angles and angular velocities of various joints. Study Design: Cohort assessing Validity and Reliability. Methods: The validity of the Nordic Angle BPA data was verified by Spearman's correlation test for consistency with the movement analysis data, and the magnitude of the correlation was indicated by rs. The agreement between these measurements was examined using the Bland-Altman analysis. The reliability of the Nordic Angle and motion analysis was examined using the intraclass correlation coefficient (ICC) (1,k) based on data from repeated trials within a day. Results: Although the spearman correlation between the Nordic angle and the angle determined using motion analysis did not reach statistical significance (p = 0.052), a very large correlation was present (rs = 0.75). The difference between the mean values of the Nordic Angle and motion analysis was 0.4 ± 2.1°, and the limits of agreement ranged from -3.9° to 4.6°. In two BPA measurements, the Nordic Angle showed perfect reliability (ICC = 1.00, p < 0.001), while motion analysis showed nearly perfect reliability (ICC = 0.97, p < 0.001). Conclusion: The Nordic Angle, which has both validity and reliability, may be appropriate for field measurement because it allows immediate feedback of BPA and the measurement of many athletes. Level of evidence: 3b©The Author(s).

Anti-idiotype monoclonal antibodies against emicizumab enable accurate procoagulant and anticoagulant assays, irrespective of the test base, in the presence of emicizumab.

INTRODUCTION: Emicizumab markedly shortens the activated partial thromboplastin time (aPTT), resulting in inaccurate measurements of procoagulant and anticoagulant factor activities. We have recently reported that mixtures of two different anti-idiotype monoclonal antibodies against emicizumab (anti-emicizumab-mAbs) allow measurement of factor (F)VIII activity (FVIII:C) and FVIII inhibitor in emicizumab-containing plasmas. It is unknown whether anti-emicizumab mAbs can work for other aPTT-based procoagulant and anticoagulant assays. AIM: To investigate whether anti-emicizumab mAbs were measured by all of the aPTT-based assays tested. METHODS: Two anti-emicizumab-mAbs (300 µg/mL each) were preincubated with emicizumab (200 µg/mL)-spiked FVIII-deficient plasma; we then measured FVIII:C, FIX:C, FXI:C, FXII:C, protein (P)C:C, PS:C, global PC-FV (aPTT-based), and prothrombin time (PT), diluted Russel's viper venom time (dRVVT), chromogenic-based FVIII:C, FIX:C and PC:C (non-aPTT-based). Emicizumab (100 µg/mL)-spiked haemophilia (H)A plasmas from patients (n = 23) were also measured. RESULTS: Emicizumab shortened the clotting time in all aPTT-based assays, resulting in high levels of FVIII:C, FIX:C, FXI:C and FXII:C; low levels of PC:C and PS:C; and false-positive results for activated PC resistance. The addition of anti-emicizumab-mAbs to emicizumab-added plasma restored all factors to the initial levels without emicizumab. Chromogenic FVIII:C measurement by human FIXa/FX was affected by emicizumab, but anti-emicizumab mAbs cancelled this effect. PT-based assays and dRVVT, chromogenic FIX:C and PC:C assays showed no effect with emicizumab. Twenty-three plasma samples from HA patients also showed similar patterns. CONCLUSION: Anti-emicizumab mAbs in vitro could cancel the effect of emicizumab, irrespective of the test base, resulting in accurate measurements of procoagulant and anticoagulant factor activity.

Effect of emicizumab-neutralizing antibodies on activated partial thromboplastin time-based clotting time test results in patients treated with emicizumab.

Background: Emicizumab is a bispecific humanized monoclonal antibody that shortens the activated partial thromboplastin time (aPTT), making aPTT-based tests unreliable. Objectives: To evaluate the efficacy of a mixture of 2 anti-idiotype monoclonal antibodies (anti-emi) in neutralizing emicizumab in samples from persons with hemophilia A treated with emicizumab. Methods: Fifty samples from persons with hemophilia A treated with emicizumab were analyzed for aPTT and factor VIII procoagulant activity; FVIII inhibitor titer was measured using Nijmegen-Bethesda assay in 50 plasma samples of additional patients (positive for FVIII inhibitor) treated with emicizumab. FVIII procoagulant activity and inhibitor titer were measured using 1-stage (Actin FS, Siemens) and chromogenic assays with bovine regents (Factor VIII Chromogenic Assay, Siemens). Emicizumab concentration was measured by modified a 1-stage assay calibrated with a drug-specific calibrator (r2 Diagnostics Inc). All the tests were performed on Sysmex CS-2400 (Sysmex) before and after the addition of anti-emi (Chugai Pharmaceutical). Results: Emicizumab concentrations measured after neutralization were <1.6 µg/mL in all samples. FVIII levels were >480 IU/dL with an aPTT of <30.8 seconds in all samples before neutralization and were <1 IU/dL with an aPTT of >70 seconds after adding anti-emi. FVIII inhibitor resulted in a false negative result in 44 of 50 samples measured with the 1-stage assay before neutralization. A good correlation (r = 0.98) was found between inhibitor titer measured using the chromogenic (insensitive to emicizumab) and 1-stage assays after neutralization. Conclusion: The anti-emi antibodies were shown to completely neutralize emicizumab, making samples pretreated with anti-emi analyzable with the 1-stage assay.

Development and validation of a novel qualitative test for plasma fibrinogen utilizing clot waveform analysis.

Plasma fibrinogen is commonly examined by Clauss fibrinogen assay, which cannot distinguish between quantitative and qualitative fibrinogen anomalies. However, our previously reported Clauss fibrinogen assay utilizing clot waveform analysis (Clauss-CWA) provides additional information that contributes to the classification of fibrinogen anomalies. In this study, we adopted the Clauss-CWA method for an autoanalyzer to automatically measure the antigenic estimate (eAg) of fibrinogen in addition to the functional amount (Ac), and to thus provide the Ac/eAg ratio as a qualitative indicator. Performance was validated by receiver operating characteristics (ROC) and precision recall (PR) curve analyses using a patient cohort, consisting of a training cohort (n = 519) and a validation cohort (n = 523), both of which contained cases of congenital (hypo)dysfibrinogenemia as qualitative defects. We obtained an optimal cutoff of 0.65 for Ac/eAg by ROC curve analysis of the training cohort, offering superior sensitivity (> 0.9661) and specificity (1.000). This cutoff was validated in the validation cohort, providing positive predictive value > 0.933 and negative predictive value > 0.998. PR curve analysis also showed that Clauss-CWA provided excellent performance for detecting qualitative fibrinogen anomalies. The Clauss-CWA method may represent a useful approach for detecting qualitative fibrinogen abnormalities in routine laboratory testing.

Coagulation assay discrepancies in Japanese patients with non-severe hemophilia A.

Patients with non-severe hemophilia A often show discrepancies in factor VIII (FVIII) activity. However, information on variant-specific coagulation assay characteristics in Japanese patients is limited. Pathogenic variants were classified into three groups, thrombin-cleavage site (TC), A1-A2-A3 interface (IF), and non-discrepant, with reference to previous studies. Cutoff values for the one-stage assay (OSA)/chromogenic substrate assay (CSA) ratio, which is suitable for distinguishing discrepancies, were determined for all five aPTT reagents. TGA and CWA parameters and bleeding scores were compared between groups. Two of the 39 patients with non-severe hemophilia A (5%) were classified as TC, 10 (26%) as IF, and 27 (69%) as non-discrepant. The OSA/CSA cutoff values between the groups varied widely by aPTT reagent and tended to be relatively low compared to previous studies. As an indicator of bleeding tendency, TGA had a low correlation coefficient for the IF variant, but this was not significant and was comparable to FVIII activity and CWA. Moreover, various parameters and bleeding tendency differed among patients with the same variants. Thus, our findings suggest that it is difficult to adequately assess the bleeding tendency of individual patients, even with the various assessments currently available.

Automated screening procedure for the phenotypes of congenital fibrinogen disorders using novel parameters, |min1|c and Ac/|min1|c, obtained from clot waveform analysis using the Clauss method.

INTRODUCTION: Fibrinogen activity (Ac) is widely measured, but fibrinogen antigen (Ag) is measured only in specialized laboratories, so it is difficult to discriminate congenital fibrinogen disorders (CFDs) from acquired hypofibrinogenemia (aHypo). In this study, to screen for CFD phenotypes we adopted novel parameters, |min1|c and Ac/ |min1|c, and compared these with validated Ac, Ag, and Ac/Ag, and previously proposed Ac/dH and Ac/|min1|. MATERIALS AND METHODS: We calibrated |min1| using a CN-6000 instrument and investigated the correlation between Ag and |min1|c for aHypo (n = 131) and CFD [18 dysfibrinogenemia (Dys), two hypodysfibrinogenemia (Hypodys) and four hypofibrinpogenemia (Hypo)]. Furthermore, we proposed a schema for screening CFD phenotypes using |min1|c and Ac/|min1|c. RESULTS: The |min1|c correlated well with Ag in aHypo, and Ac/|min1|c was a better parameter for screening Dys and Hypodys than Ac/dH and Ac/|min1|. With the combination of |min1|c and Ac/|min1|c parameters, 15 Dys, 2 Hypodys and four Hypo were categorized in agreement with the phenotype determined using Ag and Ac/Ag; conversely three Dys were classified as one Hypodys (AαR16C) and two Hypo (BßG15C). CONCLUSION: We demonstrated that |min1|c and Ac/|min1|c are valuable parameters for screening CFD patients and phenotypes in laboratories that do not measure Ag or perform genetic analysis.

Screening method for congenital dysfibrinogenemia using clot waveform analysis with the Clauss method.

INTRODUCTION: Congenital fibrinogen disorders (CFDs) are classified as afibrinogenemia or hypofibrinogenemia (Hypo), dysfibrinogenemia (Dys), or hypodysfibrinogenemia (Hypodys), according to functional and antigenic fibrinogen concentrations. However, in routine laboratory tests, plasma fibrinogen levels are mostly measured using the functional Clauss method and not as an antigenic level. Therefore, it is difficult to discriminate CFD from acquired hypofibrinogenemia (aHypo). To establish a screening method for CFD, we investigated the parameters of clot waveform analysis (CWA) from the Clauss method. METHODS: We compared fibrinogen concentrations determined using Clauss and prothrombin time (PT)-derived methods for 67 aHypo and CFD cases (19 Dys, 4 Hypodys, and 1 Hypo determined using antigen levels and DNA sequence analysis) with a CS-2400 instrument, and the CWA parameters, dH and Min1, were analyzed automatically with an on-board algorithm. dH and Min1 are the maximum change in transmittance at the end of coagulation and the maximum velocity of transmittance change during coagulation, respectively. RESULTS: Clauss/PT-derived ratios detected 18 cases of Dys and Hypodys but no Hypo cases, whereas Clauss/dH plus Clauss/Min1 ratios were calculated from fibrinogen concentration using the Clauss method and CWA parameters detected 21 cases of Dys and Hypodys and one Hypo case. Moreover, the Clauss/PT-derived ratio and Clauss/dH plus Clauss/Min1 ratio detected 22 cases of Dys and Hypodys cases and one Hypo case. CONCLUSION: This report demonstrates that CWA parameters of the Clauss method, Clauss/dH plus Clauss/Min1 ratio, screened Dys patients with a higher rate, whereas Clauss/PT-derived ratios did not.

Performance evaluation of Revohem™ FVIII chromogenic and Revohem™ FIX chromogenic in the CS-5100 autoanalyser.

INTRODUCTION: Chromogenic substrate assay (CSA) reagents Revohem™ FVIII and Revohem™ FIX are now available as in vitro diagnostic reagents for autoanalysers in Japan. In this study, we evaluated the performance of these reagents in the CS-5100 automated coagulation analyser. METHODS: We assessed within-run and between-day imprecision, on-board stability and frozen-storage stability of Revohem FVIII and FIX. Sensitivity to lupus anticoagulant (LA) was examined using LA-positive patient plasma. Correlations were analysed using plasma samples from normal individuals and patients with haemophilia A (HA) or B (HB) or von Willebrand disease (VWD). RESULTS: Imprecision was <2% for Revohem FVIII and <6.5% for Revohem FIX. On-board storage of Revohem FVIII resulted in a <10% decrease in FVIII levels from baseline at 24 hours, whereas Revohem FIX showed a >10% decrease at 8 hours. Revohem FVIII showed good stability while frozen for 22 days. Although Revohem FIX showed degradation due to freeze-thawing, a new calibration improved stability up to 22 days. Interference from LA was not observed with Revohem FVIII or FIX. The FVIII CSA-CSA correlation was excellent in normal (r = 0.9924), HA (r = 0.9945) and VWD (r = 0.9914). The FVIII CSA-OSA correlation was good in normal (r = 0.8468) and excellent in HA (r = 0.975) and VWD (r = 0.9936). The FIX CSA-OSA correlation was fair in normal (r = 0.4791) and excellent in HB (r = 0.9501). CONCLUSION: Revohem FVIII and FIX both showed excellent performance in the CS-5100 analyser. These reagents could be useful in routine laboratory testing for diagnosing and treating haemophilia.

Evaluation of an automated chromogenic assay for Factor VIII clotting activity measurement in patients affected by haemophilia A.

INTRODUCTION: The original one-stage clotting assay is still the most widely used method to measure Factor VIII clotting activity (FVIII:C) in patients with haemophilia A (HA), although the use of chromogenic assays is increasing significantly. AIM: Evaluation of the analytical performance and diagnostic accuracy of BIOPHEN™ FVIII:C (HYPHEN BioMed, Neuville-sur-Oise, France) assay on Sysmex CS-2400 (Sysmex, Kobe, Japan) analyser. METHODS: Sixty patients with haemophilia A (HA; any severity) and 120 healthy Italian subjects were included. All the assays were performed on citrate platelet-poor plasmas stored at -80°C. Chromogenic BIOPHEN™ FVIII:C was compared with the one-stage assay using Actin FS and Factor VIII deficient plasma (Siemens Healthcare Diagnostics, Marburg, Germany) on Sysmex CS-2400 and with another chromogenic automated assay (COAMATIC™ Factor VIII, CHROMOGENIX on ACL TOP analyzer; Instrumentation Laboratory, Milan, Italy). RESULTS: Intra-assay and inter-assay coefficient of variation were <6%. Linearity was good up to 1/128 dilution (r = 0.99); mean recovery was 91.7% and limit of detection was 0.2%. BIOPHEN™ FVIII:C assay showed a good correlation and diagnostic agreement with the chromogenic COAMATIC™ assay: the Spearmen's Rank correlation coefficient was 0.98 and the inter-rate agreement K Cohen coefficient was 0.61. The K coefficient was 0.91 when BIOPHEN™ FVIII:C was compared with the historical classification of the patients, demonstrating an optimal diagnostic accuracy in HA. CONCLUSIONS: BIOPHEN™ FVIII:C showed good analytical performance and diagnostic accuracy and could be considered suitable for the introduction in routine analytical panel of coagulation for the diagnosis of HA patients.

Clot waveform analysis in Clauss fibrinogen assay contributes to classification of fibrinogen disorders.

BACKGROUND: Clauss fibrinogen assay (CFA) is widely used as a screening test to detect fibrinogen disorders. However, CFA alone cannot distinguish quantitative and qualitative defects because it depends on functional fibrinogen activity (Ac), and fibrinogen antigen (Ag) determination is required to classify fibrinogen disorders. OBJECTIVES: To establish a novel approach to classify fibrinogen disorders, we investigated the potential of clot waveform analysis (CWA) of CFA and searched for a surrogate marker for fibrinogen Ag. MATERIALS AND METHODS: We analyzed CWA parameters obtained from CFA using plasma from normal patients (n = 91) and those with fibrinogen disorders (n = 27, including 15 hypofibrinogenemia, 6 dysfibrinogenemia and 6 hypodysfibrinogenemia) with a CS-5100 autoanalyzer. RESULTS: We found that maximum coagulation velocity (Min1) levels were most strongly correlated with fibrinogen Ag in both normal and fibrinogen disorders. Hence, Min1 appeared to function as a surrogate for fibrinogen Ag. Although the Ac/Min1 ratio did not simply reflect the measured Ac/Ag ratio, we found that the Ac/Min1 ratio was significantly higher than normal in hypofibrinogenemia and hypodysfibrinogenemia, but not in dysfibrinogenemia. On the other hand, we could distinguish type II deficiency from type I using estimated fibrinogen Ag (eAg) predicted from Min1. The Ac/eAg ratios of dysfibrinogenemia and hypodysfibrinogenemia were significantly lower than those of normal and hypofibrinogenemia. CONCLUSION: The CWA of CFA could distinguish fibrinogen disorders using a combination of Ac/Min1 and Ac/eAg values. This analysis allows the qualitative detection of fibrinogen disorder easily and represents a novel screening test for fibrinogen disorders.

Molecularly Imprinted Filtering Adsorbents for Odor Sensing.

Versatile odor sensors that can discriminate among huge numbers of environmental odorants are desired in many fields, including robotics, environmental monitoring, and food production. However, odor sensors comparable to an animal's nose have not yet been developed. An animal's olfactory system recognizes odor clusters with specific molecular properties and uses this combinatorial information in odor discrimination. This suggests that measurement and clustering of odor molecular properties (e.g., polarity, size) using an artificial sensor is a promising approach to odor sensing. Here, adsorbents composed of composite materials with molecular recognition properties were developed for odor sensing. The selectivity of the sensor depends on the adsorbent materials, so specific polymeric materials with particular solubility parameters were chosen to adsorb odorants with various properties. The adsorption properties of the adsorbents could be modified by mixing adsorbent materials. Moreover, a novel molecularly imprinted filtering adsorbent (MIFA), composed of an adsorbent substrate covered with a molecularly imprinted polymer (MIP) layer, was developed to improve the odor molecular recognition ability. The combination of the adsorbent and MIP layer provided a higher specificity toward target molecules. The MIFA thus provides a useful technique for the design and control of adsorbents with adsorption properties specific to particular odor molecules.

Fluid structure interaction analysis reveals facial nerve palsy caused by vertebral-posterior inferior cerebellar artery aneurysm.

Cranial nerve palsy caused by aneurysmal compression has not been fully evaluated. The main causes of symptoms are considered to be direct mechanical compression and aneurysm pulsations. Recent studies indicate that nerve dysfunction is mainly induced by pulsation rather than by direct compression, and successful cases of endovascular surgery have been reported. We describe a patient with an unruptured vertebral artery-posterior inferior cerebellar artery (VA-PICA) aneurysm compressing the facial nerve at the root exit zone (REZ). The patient presented with peripheral facial nerve palsy but not hemifacial spasm and was successfully treated by coil embolization. To investigate the mechanisms underlying peripheral facial nerve palsy, fluid structure interaction (FSI) analysis can approximate displacement and the magnitude of aneurysmal wall motion due to hemodynamic forces. In our case, maximum mesh displacement was observed at the aneurysmal wall attached to the facial nerve inside the pons rather than the REZ, which explains the clinical manifestation of facial nerve palsy in the absence of hemifacial spasm. This preliminary report demonstrates the utility of FSI analysis for investigating cranial nerve neuropathy.

Fabrication of in vitro three-dimensional multilayered blood vessel model using human endothelial and smooth muscle cells and high-strength PEG hydrogel.

We fabricated a three-dimensional multilayered blood vessel model using human cells and high-strength PEG hydrogel. The hydrogel tube was physically suitable for perfusion culture, and cells were cultured on the hydrogel surface by binding with fibronectin. Using the layer-by-layer cell multilayered technique, we successfully constructed an artificial blood vessel.