RESUMO
The study aimed to analyze the stress/strain distribution of new designs of mini-implants manufactured by machining and additive manufacturing. Four designs were evaluated (Ø2.0 mm × 10 mm): Intra-lock, helical, threaded machined (MN threaded) and threaded by additive manufacturing (AM threaded). Analysis of stress was performed through photoelastic analysis (100 N axial/oblique loads) and analysis of strain by digital image correlation (DIC) (250 N axial/100 N oblique load). Data distribution was verified using the Shapiro-Wilk test and a significance level of 5% was adopted. Quantitative data were analyzed using the non-parametric Kruskal-Wallis test. In photoelastic analysis, the Intra-lock mini-implant showed the highest stresses in the cervical (104 kPa), middle (108 kPa), and apical (212 kPa) thirds. Higher stresses were observed in the oblique loading situation for all designs. For DIC analysis, axial loading, a significant difference was observed for the AM Threaded mini-implants about the other designs in the cervical third (p = .04), with the highest strain value 47 µÎµ [10; 76]. In oblique loading, a significant difference between the mini-implants was observed in the middle and apical thirds, with higher strains for the AM threaded design -185 µÎµ [-173; 162] (p = .009) and 242 µÎµ [87; 372] (p = .013), respectively. In general, the influence of different mini-implant designs and the additive manufacturing method on the stress/strain was observed, in the photoelastic and DIC analysis. The evaluated designs demonstrated a lower concentration of stress/strain in the cervical region compared to the apical region, and higher stress/strain in situations of oblique load compared with axial load.
RESUMO
Objective: The aim of this systematic review was to present the current knowledge on the influence of laser surface treatment on the adhesion of bacteria to titanium and its alloys. Design: This review was structured according to PRISMA guidelines for systematic reviews and meta-analyses, and registered on the Open Science Framework platform (https://doi.org/10.17605/OSF.IO/FTA3W). Article searches were performed in 4 databases: PubMed, Scopus, Embase, and Science Direct. In addition, a manual search was performed in the reference lists of the selected articles. The selection of articles was performed by two reviewers. The articles found were screened for eligibility using the previously established inclusion and exclusion criteria. The methodological quality of the studies was assessed using the Joanna Briggs Institute (JBI) Critical Assessment Checklist for Quasi-Experimental Studies (non-randomized experimental studies). Results: Most of the studies evaluated showed that surface treatment by laser irradiation can affect the adhesion of bacteria to titanium surfaces and that this is directly related to changes in surface properties such as chemical composition, morphology, roughness, and wettability, as well as the type of bacterial species involved. Conclusions: The studies considered in this systematic review have shown that surface treatment by laser irradiation is a promising technique to reduce the adhesion of bacteria on the surface of titanium implants.
RESUMO
Surface treatment by laser irradiation can change the topography of titanium; however, little is known about the changes it causes when applied to other coatings. This study aimed to evaluate the influence of Er:YAG laser irradiation on the surface properties of titanium-aluminum-vanadium (Ti-6Al-4V) discs. Four Ti-6Al-4V surfaces were evaluated (n = 10): CON-control, machined without surface treatment; LT-machined + laser treatment; HA-hydroxyapatite coating; and LT-HA-hydroxyapatite coating + laser treatment. For the laser treatment, an Er:YAG laser with a wavelength of 2940 nm, a frequency of 10 Hz, and an energy density of 12.8 J/cm2 was used. The morphology of the coating was investigated by scanning electron microscopy and the surface composition by energy-dispersive X-ray spectroscopy. The influence of laser irradiation treatment on roughness and wettability was also evaluated. The Er:YAG laser promoted a significant reduction in the roughness Sa (p < 0.05) and in the contact angle (p = 0.002) of the LT surface compared to the CON surface. On the LT-HA surface, a significant decrease in roughness was observed only for the Rz parameter (p = 0.015) and an increase in the contact angle (p < 0.001) compared to the HA surface. The use of the Er:YAG laser with the evaluated parameters decreased the surface roughness and improved the wetting capacity of machined without surface treatment. In the group with hydroxyapatite coating, the laser influenced the surface roughness only for the parameter Rz and reduced their wetting capacity.
Assuntos
Durapatita , Lasers de Estado Sólido , Durapatita/química , Titânio , Alumínio , Vanádio , Propriedades de Superfície , Ligas , Microscopia Eletrônica de VarreduraRESUMO
STATEMENT OF PROBLEM: High-power laser irradiation may be a promising treatment for titanium dental implant surfaces. However, systematic reviews of the influence of high-power laser irradiation on the different properties of titanium surfaces are lacking. PURPOSE: The purpose of this systematic review was to analyze the influence of surface treatment by high-power laser irradiation on the surface properties of titanium and its alloys. MATERIAL AND METHODS: The PubMed, LILACS, COCHRANE library, and Science Direct databases were searched, and articles published in the last 10 years were included. Of the 725 articles initially identified, 27 were selected after full reading and the application of inclusion and exclusion criteria. RESULTS: The studies evaluated showed that laser irradiation treatment, depending on the settings and parameters used, promoted changes in the surface properties of titanium. In general, lower speed and a higher number of scans increased roughness. Laser surface treatment promoted the inclusion of more oxygen and improved the wetting capacity of titanium. Additionally, laser treatment improved the adherence of coatings. CONCLUSIONS: Changes in the surface properties of titanium after laser treatment have been demonstrated. However, determining protocols with specific parameters is necessary to optimize the results.