Performance investigations for sustainability assessment of Hastelloy C-276 under different machining environments.

Hastelloy is categorized as difficult to cut superalloy widely used in aerospace, nuclear reactor components and chemical industry because of its magnificent strength and higher heat efficiency. Since, the machining of this material is quite difficult and hence suitable cooling systems are required to achieve sustainable manufacturing goals. The present investigation has been focused on the machining performance and sustainability assessment of turning Hastelloy C-276 in dry, flood and minimum quantity lubrication (MQL) environments. Taguchi L-9 array has been utilized to conduct and record the experimental output along with TOPSIS approach to evaluate the sustainability. The output responses viz. cutting forces, surface roughness, cutting temperature, energy consumption and carbon emission have been recorded at various levels of input variables. The experimental results revealed that MQL has minimized the cutting forces, surface roughness and temperature by margin of 20-38%. Likewise, energy expenditure and carbon emission was declined by 9-27% respectively compared to other conditions. Sustainability analysis explored best performance index during equal weightage criteria at 125 m/min, 0.246 and 0.8 mm doc under MQL. However, implementing assigned weightage system evaluated best condition for dry machining as 88 m/min and 0.246 mm/rev having same doc. SEM analysis of insert reported mainly abrasion and adhesion type of tool wear at all parametric range and machining conditions.

Joining of Dissimilar Al and Mg Metal Alloys by Friction Stir Welding.

In engineering applications, such as automobile, marine, aerospace, and railway, lightweight alloys of aluminum (Al) and magnesium (Mg) ensure design fitness for fuel economy, better efficiency, and overall cost reduction. Friction stir welding (FSW) for joining dissimilar materials has been considered better than the conventional fusion welding process because of metallurgical concerns. In this study, dissimilar joints were made between the AA6061 (A), AZ31B (B), and AZ91D (C) combinations based on the varying advancing side (AS) and retreating side (RS). The dissimilar joints prepared by the FSW process were further characterized by tensile testing, impact testing, corrosion testing, fracture, and statistical and cost analysis. The results revealed a maximum tensile strength of 192.39 MPa in AZ91 and AZ31B, maximum yield strength of 134.38 MPa in a combination of AA6061 and AZ91, maximum hardness of 114 Hv in AA6061 and AZ31B, and lowest corrosion rate of 7.03 mV/A in AA6061 and AZ31B. The results of the properties were supported by photomicrographic fracture analysis by scanning electron microscopy (SEM) observations. Further, the performance of dissimilar joints was statistically analyzed and prioritized for preference by similarity to the ideal solution (TOPSIS) method.

Experimental Investigation and Performance Optimization during Machining of Hastelloy C-276 Using Green Lubricants.

Smart manufacturing is the demand of industry 4.0, in which the mass production of difficult-to-cut materials is of great concern to fulfil the goal of sustainable machining. Presently, the machining of superalloy is of upmost interest because of its wide application. However, the limited data on the turning of Hastelloy C-276 highlights its challenges during processing. Hence, the machining performance of superalloy considering surface quality, thermal aspects and chip reduction coefficient was examined with minimum quantity lubrication of several oils to address the sustainable development goal (SDG-12). The output responses were optimized through response surface methodology along with analysis of variance. The research exhibited that the output responses were dominated by cutting speed and feed rate having a percentage benefaction of 24.26% and 60%, respectively, whilst the depth of cut and lubricant type have an influence of 10-12%. No major difference in temperature range was reported during the different lubrication conditions. However, a substantial variation in surface roughness and the chip reduction coefficient was revealed. The percentage error evaluated in surface roughness, temperature and chip reduction coefficient was less than 5%, along with an overall desirability of 0.88, describing the usefulness of the model used. The SEM micrograph indicated a loss of coating, nose and flank wear during all lubrication conditions. Lastly, incorporating a circular economy has reduced the economic, ecological and environmental burden.

Hand and Abrasive Flow Polished Tungsten Carbide Die: Optimization of Surface Roughness, Polishing Time and Comparative Analysis in Wire Drawing.

This research work highlights the benefits of abrasive flow polishing (AFP) applied to tungsten carbide dies compared with conventional hand polishing (HP). An indigenous experimental set-up for AFP was developed. The effect of prominent process parameters viz. extrusion pressure, number of cycles, and abrasive particle concentration on the final surface roughness, percentage improvement in surface roughness, and polishing time was investigated by Taguchi-designed experiments. The multi-objective optimization (MOO) was performed using the Taguchi-TOPSIS-Equal weight approach to find the respective optimized AFP parametric settings. A set of skilled operators performed the conventional HP of dies, and the best hand-polished (HPed) die was selected using the TOPSIS technique. The operational performance of the HPed dies and the abrasive flow polished (AFPed) dies were compared on the three-stage wire drawing operation. The results revealed that AFP's surface resulted in a better-quality surface than hand polishing with a 27.06% improvement in surface roughness. Furthermore, AFP can reduce the dependency on costly and tricky-to-locate skilled operators, with a reasonable amount of time saving (about 87.05%). Overall, the study's findings show that abrasive flow polishing of dies is fast and cost-effective.

Multiple-Criteria Decision-Making and Sensitivity Analysis for Selection of Materials for Knee Implant Femoral Component.

Total knee replacement (TKR) is a remarkable achievement in biomedical science that enhances human life. However, human beings still suffer from knee-joint-related problems such as aseptic loosening caused by excessive wear between articular surfaces, stress-shielding of the bone by prosthesis, and soft tissue development in the interface of bone and implant due to inappropriate selection of TKR material. The choice of most suitable materials for the femoral component of TKR is a critical decision; therefore, in this research paper, a hybrid multiple-criteria decision-making (MCDM) tactic is applied using the degree of membership (DoM) technique with a varied system, using the weighted sum method (WSM), the weighted product method (WPM), the weighted aggregated sum product assessment method (WASPAS), an evaluation based on distance from average solution (EDAS), and a technique for order of preference by similarity to ideal solution (TOPSIS). The weights of importance are assigned to different criteria by the equal weights method (EWM). Furthermore, sensitivity analysis is conducted to check the solidity of the projected tactic. The weights of importance are varied using the entropy weights technique (EWT) and the standard deviation method (SDM). The projected hybrid MCDM methodology is simple, reliable and valuable for a conflicting decision-making environment.

Vibration Exposure and Transmissibility on Dentist's Anatomy: A Study of Micro Motors and Air-Turbines.

The use of dental hand pieces endanger dentists to vibration exposure as they are subjected to very high amplitude and vibration frequency. This paper has envisaged a comparative analysis of vibration amplitudes and transmissibility during idling and drilling with micro motor (MM) and air-turbine (AT) hand pieces. The study aims to identify the mean difference in vibration amplitudes during idling, explore different grasp forces while drilling with irrigant injection by the dentist, and various vibration transmission of these hand pieces. The study utilized 22 separate frequency resonances on two new and eight used MMs and two new and eight used ATs of different brands by observing the investigator at 16 different dentist clinics. The study adopted a descriptive research design with non-probability sampling techniques for selecting dentists and hand pieces. Statistical methods like Levene Test of Homogeneity, Welch ANOVA, independent t-test, and Games-Howell test were utilized with SPSS version 22 and MS-Excel. The results reveal that vibration amplitudes and vibration transmissibility when measured at position 2 are higher than in another position 1. Vibrations during idling for used MMs are more than AT hand pieces, and the used MM (MUD) and used AT (AUA) hand pieces differ due to their obsolescence and over-usage. Vibration amplitudes increase every time with the tightening of grasping of the hand piece. Vibration amplitudes for each grasping style of MM hand piece differ from all other grasping styles of AT hand pieces. Routine exposure to consistent vibrations has ill physical, mental, and psychological effects on dentists. The used hand pieces more hazardous as compared to newer ones. The study suggests that these hand pieces must be replaced periodically, sufficient to break between two operations, especially after every hand piece usage. Hence, the present research work can be further extended by creating some control groups among dentists and then studying the vibration amplitude exposure of various dental hand pieces and subsequent transmissibility to their body parts.