Investigations of Metallurgical Differences in AISI 347 and Their Influence on Deformation and Transformation Behaviour and Resulting Fatigue Life.

Due to variations in chemical composition and production processes, homonymous austenitic stainless steels can differ significantly regarding their initial microstructure, metastability, and thus, their fatigue behavior. Microstructural investigations and fatigue tests have been performed in order to evaluate this aspect. Three different batches and production forms of nominally one type of steel AISI 347 were investigated under monotonic tensile tests and cyclic loading under total strain and stress control in low and high cycle fatigue regimes, respectively. The deformation induced α'-martensite formation was investigated globally by means of in situ magnetic measurements and locally using optical light microscopy of color etching of micrographs. The investigation showed that the chemical composition and the different production processes influence the material behavior. In fatigue tests, a higher metastability and thus a higher level of deformation induced α'-martensite pronounced cyclic hardening, resulting in significantly greater endurable stresses in total strain-controlled tests and an increase in fatigue life in stress-controlled tests. For applications of non-destructive-testing, detailed knowledge of a component's metastability is required. In less metastable batches and for lower stress levels, α'-martensite primarily formed at the plasticization zone of a crack. Furthermore, the formation and nucleation points of α'-martensite were highly dependent on grain size and the presence of δ-ferrite. This study provides valuable insights into the different material behavior of three different batches with the same designation, i.e., AISI 347, due to different manufacturing processes and differences in the chemical composition, metastability, and microstructure.

Detection of Microstructural Changes in Metastable AISI 347, HSS Z-M4 and Tool Steel Ferrotitanit WFN by Mechanical Loss Coefficient at Ultrasonic Frequencies.

Ultrasonic processes such as ultrasonic welding or ultrasonic fatigue testing use power ultrasound to stimulate materials with amplitudes in the range of 1-100 µm. The ultrasonic welding process is sensitive to any changes in the system or even the environment that may result in lower joint quality. The welding tools, so called sonotrodes, have to be accurately designed to endure high mechanical and thermal loads while inducing a sufficient amount of welding energy into the joining zone by oscillation with the Eigenfrequency of the whole system. Such sonotrodes are often made of thermally treated metals where the heat treatment is accompanied by microstructural changes. During ultrasonic stimulation, the material may further change its properties and microstructure due to cyclic loading. Both are expected to be recognized and identified by loss coefficients. Therefore, the loss coefficient was determined by modal analysis of rods and fatigue specimen made of different materials to correlate microstructural changes to attenuation. The determined loss coefficients indicated microstructural changes in all materials investigated, confirming results from previous investigations that showed an increasing attenuation due to cyclic loading for AISI 347. For the sonotrode materials Z-M4 PM and Ferrotitanit WFN, the loss coefficients decreased due to thermal treatments. Technically most relevant, changes in elastic modulus due to thermal treatments were quantitatively related to frequency changes, which can significantly simplify future sonotrode development.

Micromagnetic and Microstructural Characterization of Ferromagnetic Steels in Different Heat Treatment Conditions.

The paper addresses the investigation of microstructures from AISI 52100 and AISI 4140 in hardened as well as in quenched and tempered conditions. The specimens are compared in terms of their magnetic hysteresis and their microstructural and mechanical properties. Material properties were determined by hardness, microhardness, and X-ray diffraction measurements. Two different approaches were used to characterize magnetic properties via a hysteresis frame device, aiming, on the one hand, to record the magnetic hysteresis with established proceedings by setting a constant magnetic flux and, on the other hand, by offsetting a constant field strength to facilitate reproducibility of the results with other micromagnetic measurement systems. Comparable differences in both the micromagnetic and the mechanical material properties could be determined and quantified for the specifically manufactured specimens. The sensitivity of the magnetic hysteresis and, determined from that, the relationship between magnetic flux and magnetic field strength were confirmed. It was shown that a consistent change in hysteresis shape from hardened to high temperature tempered material states develops and that this change allows the characterization of different materials without the need to adjust magnetization parameters. Repeatedly, an increase in remanence with decreasing hardness was found for both test approaches. Likewise, a decreasing coercivity and increasing maximum magnetic flux could be detected with decreasing retained austenite content. The investigated correlations should thus contribute to the calibration of comparable measurement systems through the holistic characterized specimens.