Dissolution behavior of stone wool fibers in synthetic lung fluids: Impact of iron oxidation state changes induced by heat treatment for binder removal.

Stone wool fiber materials are commonly used for thermal and acoustic insulation, horticulture and filler purposes. Biosolubility of the stone wool fiber (SWF) materials accessed through acellular in vitro dissolution tests can potentially be used in future as an indicator of fiber biopersistence in vivo. To correlate acellular in vitro studies with in vivo and epidemiological investigations, not only a robust dissolution procedure is needed, but fundamental understanding of fiber behavior during sample preparation and dissolution is required. We investigated the influence of heat treatment procedure for binder removal on the SWF iron oxidation state as well as on the SWF dissolution behavior in simulant lung fluids (with and without complexing agents). We used heat treatments at 450 °C for 5 min and 590 °C for 1 h. Both procedures resulted in complete binder removal from the SWF. Changes of iron oxidation state were moderate if binder was removed at 450 °C for 5 min, and there were no substantial changes of SWF's dissolution behavior in all investigated fluids after this heat treatment. In contrast, if binder was removed at 590 °C for 1 h, complete Fe(II) oxidation to Fe(III) was observed and significant increase of dissolution was shown in fluids without complexing agent (citrate). PHREEQC solution speciation modeling showed that in this case, released Fe(III) may form ferrihydrite precipitate in the solution. Precipitation of ferrihydrite solid phase leads to removal of iron cations from the solution, thus shifting reaction towards the dissolution products and increasing total mass loss of fiber samples. This effect is not observed for heat treated fibers if citrate is present in the fluid, because Fe(III) binds with citrate and remains mobile in the solution. Therefore, for developing the most accurate SWF in vitro acellular biosolubility test, SWF heat treatment for binder removal is not recommended in combination with dissolution testing in fluids without citrate as a complexing agent.

Initial evaluation of USP apparatus 4 for measuring dissolution profile of man-made vitreous fibers.

We report the successful evaluation of a US Pharmacopeia Apparatus 4 (USP-4) system in measuring the dissolution profiles of man-made vitreous fibers (MMVF)1. Glass and stone wool fibers with different (high- and low-) solubility profiles were tested in closed-loop configuration using a sodium/potassium phosphate buffer solution or an acetate buffer, respectively. Results confirm a need to operate in diluted conditions to avoid silicon saturation in the simulant solution and suppression of fiber dissolution. A clear fiber-to-fiber differentiation with good cell-to-cell reproducibility was achieved. These findings support the continued development of a USP-4 protocol for MMVF in vitro acellular testing.

Atomistic simulations of calcium aluminosilicate interfaced with liquid water.

The dissolution behavior of calcium aluminosilicate based glass fibers, such as stone wool fibers, is an important consideration in mineral wool applications for both the longevity of the mineral wool products in humid environments and limiting the health impacts of released and inhaled fibers from the mineral wool product. Balancing these factors requires a molecular-level understanding of calcium aluminosilicate glass dissolution mechanisms, details that are challenging to resolve with experiment alone. Molecular dynamics simulations are a powerful tool capable of providing complementary atomistic insights regarding dissolution; however, they require force fields capable of describing not-only the calcium aluminosilicate surface structure but also the interactions relevant to dissolution phenomena. Here, a new force field capable of describing amorphous calcium aluminosilicate surfaces interfaced with liquid water is developed by fitting parameters to experimental and first principles simulation data of the relevant oxide-water interfaces, including ab initio molecular dynamics simulations performed for this work for the wüstite and periclase interfaces. Simulations of a calcium aluminosilicate surface interfaced with liquid water were used to test this new force field, suggesting moderate ingress of water into the porous glass interface. This design of the force field opens a new avenue for the further study of calcium and network-modifier dissolution phenomena in calcium aluminosilicate glasses and stone wool fibers at liquid water interfaces.

Investigation of the occurrence of binder material on airborne respirable mineral wool fibers.

Mineral wool fibers can be released into the air during the production and handling of a mineral wool product where a small fraction of fibers will stay airborne and can potentially be inhaled. The aerodynamic fiber diameter determines how far an airborne fiber can pass through the human airway. Respirable fibers with an aerodynamic diameter < 3 µm can reach the deep part of the lungs (i.e., the alveolar region). Binder material (i.e., organic binder and mineral oil) is used in the production of mineral wool products. However, at the current stage, it is unknown if airborne fibers can contain binder material. We explored binder presence on airborne respirable fiber fractions being released and collected during the installation of two mineral wool products (a stone wool product and a glass wool product). Fiber collection was done by pumping a controlled air volume (2, 13, 22, and 32 l/min) through polycarbonate membrane filters during the installation of the mineral wool products. The morphological and chemical composition of the fibers were studied using scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDXS) analysis. The study demonstrates that binder material is found on the surface of the respirable mineral wool fiber mainly as circular or elongated droplets. Our findings suggest that respirable fibers explored in previous epidemiological studies, which have been used for proving a lack of hazardous effects of mineral wool on humans, may have also contained binder materials on the fibers.

Surface evolution of aluminosilicate glass fibers during dissolution: Influence of pH, solid-to-solution ratio and organic treatment.

Materials made of synthetic vitreous mineral fibers, such as stone wool, are widely used in construction, in functional composites and as thermal and acoustic insulation. Chemical stability is an important parameter in assessing long term durability of the products. Stability is determined by fiber resistivity to dissolution, where the controlling parameters are solid surface area to solution volume ratio (S/V), pH and composition of the fibers and organic compounds used as binders. We investigated stone wool dissolution under flow through conditions, far from equilibrium, at pH range of 2 to 13, as well as under batch conditions, close to equilibrium, for up to 28 days, where S/V ranged from 100 to 10000 m-1. The dissolution rate of stone wool shows minimum at pH 8.5 and increases significantly at pH < 4.5 and pH > 12. In close to equilibrium conditions, S/V defines the steady state concentration for the leached components. Decreased dissolution rate could result from evolution of a surface leached layer or the formation of secondary surface phases or both. We suggested three dissolution rate controlling mechanisms, which depend on pH. That is, dissolution is controlled by: a SiO2 rich surface layer at pH < 4.5; by adsorption of an Al and Al-Si mixed surface layer at 5 < pH < 11 and by divalent cation adsorption and formation of secondary phases (silicates, hydroxides) at pH âˆ¼ 13. The organic compounds, used to treat the stone wool fibers during manufacture, had no influence on their dissolution properties.

The dissolution of stone wool fibers with sugar-based binder and oil in different synthetic lung fluids.

The biopersistence of fiber materials is one of the cornerstones in estimating potential risk to human health upon inhalation. To connect epidemiological and in vivo investigations with in vitro studies, reliable and robust methods of fiber biopersistence determination and understanding of fiber dissolution mechanism are required. We investigated dissolution properties of oil treated stone wool fibers with and without sugar-based binder (SBB) at 37 °C in the liquids representing macrophages intracellular conditions (pH 4.5). Conditions varied from batch to flow of different rates. Fiber morphology and surface chemistry changes caused by dissolution were monitored with scanning electron microscopy and time-of-flight secondary ion mass spectrometry mapping. Stone wool fiber dissolution rate depends on liquid composition (presence of ligands, such as citrate), pH, reaction products transport and fibers wetting properties. The dissolution rate decreases when: 1) citrate is consumed by the reaction with the released Al cations; 2) the pH increases during a reaction in poorly buffered solutions; 3) the dissolution products are accumulated; 4) fibers are not fully wetted with the fluid. Presence of SBB has no influence on dissolution rate if fiber material was wetted prior to dissolution experiment to avoid poorly wetted fiber agglomerates formation in the synthetic lung fluids.

Surface Reactivity and Dissolution Properties of Alumina-Silica Glasses and Fibers.

The ability of bulk glass and fibers to react in aqueous solution, with organic polymers and coupling agents, depends on the surface charge, reactivity, and adsorption properties of the glass surface, i.e. the character and density of surface -OH groups, whereas glass and fiber chemical stability and biosolubility depend on the resistance to dissolution. If glass dissolution products are accumulated in a media, they can change the surface properties by specific adsorption. We determined the -OH surface concentration, reactivity, adsorption, and dissolution properties of aluminosilicate glasses containing various modifiers and compared the results with the behavior of complex mineral wool fibers. Using proton consumption and element release from batch surface titration experiments, over the range 5 < pH < 10, surface -OH adsorption properties were modeled with the FITEQL program. During titration, network modifiers in the glass subsurface are preferentially replaced by protons, resulting in cation accumulation in the solution and formation of a leached layer enriched with Si on the solid. The behavior of Al was different. At 5 < pH < 9, only very small amounts of Al were found in the leachates, which can be explained by almost complete Al adsorption as stable surface complexes, i.e. >XOAl(OH)2 (where X = Si or Al and > represents the surface). At pH > 9, divalent cations adsorbed specifically, as >XOMe+ complexes (Me = Ca or Mg). This deeper understanding of the surface behavior of glasses and fibers is important for the design of composite materials, for applications in biology and medicine and in materials production in general, as well as for understanding natural processes, such as global uptake estimates of CO2 during rock weathering.

Effect of Norwegian fish powder on risk factors for coronary heart disease among hypercholesterolemic individuals.

BACKGROUND AND AIM: Numerous studies suggest an association between high intake of fatty fish and reduced risk of coronary heart disease. Very long-chain omega-3 fatty acids are thought to be responsible for the benefits observed, though other fatty fish components may act in concert with them. Norwegian fish powder is a dry herring product that contains essential amino acids, marine omega-3 fatty acids, vitamins and minerals. The aim of the present study was to determine whether it has beneficial effects on risk factors for coronary heart disease in man. METHODS AND RESULTS: A single center, randomized, double-blind, parallel-treatment study was carried out for 12 weeks. Subjects with primary hypercholesterolemia were randomly allocated to 10 g fish powder or placebo (20 tablets/day). Participants were instructed to follow National Cholesterol Education Program (NCEP) Step I Diet during a 4-week diet run-in phase and during the study. Concentrations of lipids, lipoproteins, hemostatic variables and endothelial cell markers were determined before and after supplementation. Our data showed that the fish powder supplement was well tolerated. A significant decrease and increase respectively were observed in plasma alpha-linolenic acid (p = 0.03) and docosahexaenoic acid (DHA) (p = 0.03). Concentrations of lipids, lipoproteins, homocysteine, factor VII, fibrinogen, tissue plasminogen activator (tPA), plasminogen activator inhibitor (PAI)-1, soluble intercellular adhesion molecule (ICAM)-1, P-selectin and interleukin (IL)-8 were not beneficially affected. CONCLUSIONS: Fish powder supplementation does not seem an effective approach to improve risk factors for coronary heart disease in hypercholesterolemic subjects following the NCEP Step I Diet.

Combined effects of chilling rate, low voltage electrical stimulation and freezing on sensory properties of bovine M. longissimus dorsi.

The single and combined effects of low voltage electrical stimulation (LVES), chilling rate after slaughter, and freezing/thawing during ageing on the tenderness of bovine M. longissimus dorsi were studied. Of 27 young bulls, 14 were exposed to LVES (90 V, 32 s, 15 Hz) immediately after stunning. Four different treatments regarding chilling rate and freezing/thawing were randomly assigned to each of the 27 young bulls. Samples were aged for 7 days at 4°C and analyzed after freezing and thawing. The experimental design allowed direct comparison of different treatment effects and an assessment whether these were additive or not. As expected chilling rate after slaughter had highly significant effects on final tenderness, based on results from a trained sensory panel and Warner Bratzler (WB) shear press analysis. The effect of LVES on final tenderness was not statistically significant. The introduction of a freezing/thawing step during ageing did not significantly affect tenderness. The effects of individual treatments depended on the tenderness level and were relatively larger at high WB shear press values (7-8 kg/cm(2)) than at low values (4-5 kg/cm(2)). The results indicate that the treatment effects were not additive, but that the treatments are alternatives to tenderize beef.