Investigating the role of non-ionic surfactants as electrolyte additives for improved zinc anode performance in aqueous batteries.

Zinc metal anodes encounter significant challenges, including dendrite growth, hydrogen evolution, and corrosion, all of which impede the rate capability and longevity of aqueous zinc-ion batteries (AZIBs). To effectively tackle these issues, we introduced Tween-80 into the traditional ZnSO4 electrolyte as an additive. Tween-80 possesses electronegative oxygen atoms that enable it to adsorb onto the zinc (Zn) anode surface, facilitating the directional deposition of Zn metal along the (002) orientation. The hydroxyl and ether groups within Tween-80 can displace some of the coordinated water molecules in the Zn2+ inner solvation shell. This disruption of the hydrogen bond network regulates the solvation structure of Zn2+ ions and suppresses the possibility of hydrogen evolution. Moreover, the long hydrocarbon chain present in Tween-80 exhibits excellent hydrophobic properties, aiding in the resistance against corrosion of the Zn anode by water molecules and reducing hydrogen evolution. Consequently, a symmetric cell equipped with the Tween-80 additive can cycle stably for over 4000 h at 1 mA cm-2 and 1 mA h cm-2. When paired with the V2O5 cathode, the full cell demonstrates a high-capacity retention rate exceeding 80 % over 1000 cycles at a current density of 2 A g-1. This study underscores the advantages of utilizing non-ionic surfactants for achieving high-performance aqueous zinc-ion batteries.

[Analysis and Optimization Suggestions on Allowance Allocation Methods of the Power Industry in the Carbon Market].

The initial allocation of carbon emission allowances is an important component of the carbon market. An equitable, scientific, and operational quota allocation method and quota management system are the cornerstones for ensuring the healthy operation of the carbon market. Owing to the high emissions, simple process, and good data foundation, the pilot and national carbon market in China have initially included the power industry in allowance management and introduced a common and differentiated quota allocation method. In this study, we compared the allowance allocation methods for the power industry and summarized the methods for key issues such as unit classification, correction factor, product measurement, and quota carry-over. We observed that there were concerns, such as lagging issuance time, lack of carry-over provisions, lack of regulatory mechanisms, and imperfect methods, in the first performance cycle of the national carbon market quota allocation. We improved the allowance allocation system for the power industry in the carbon market from the methodological and management perspectives, including establishing a total allowance constraint, clarifying quota carry-over provisions, improving the quota verification method for co-firing units, optimizing correction factors' selection, and introducing a compensatory distribution system in a timely manner.

Pain perception, aqueous humour cytokines, and miosis response following first and second eye femtosecond laser-assisted cataract surgery: A randomised, prospective, intraindividual study.

BACKGROUND: To compare pain perception, pupil behaviours, and cytokine levels during first-eye and second-eye femtosecond laser-assisted cataract surgery (FLACS) and determine which is better regarding a short or long interval for bilateral FLACS. METHODS: Notably, 96 eyes of 48 patients with bilateral cataracts underwent the first surgeries in the left or right eye, according to a random sequence. They were further randomised into 2- and 6-week subgroups based on surgery intervals. Pupil size was measured from captured images, and pain perception was assessed using a visual analog scale (VAS). Aqueous humour prostaglandin E2 (PGE2), monocyte chemoattractant protein-1 (MCP-1), interleukin (IL)-6, and IL-8 levels were also quantitatively analysed. All patients were followed for 1 week to evaluate changes in endothelial cell density (ECD), central corneal thickness (CCT), and macular central subfield thickness (CST). RESULTS: Ocular pain was significantly higher in patients who underwent second-eye FLACS. First tear break-up time was negatively correlated with VAS score. MCP-1 levels were significantly higher in patients who underwent second-eye FLACS, and VAS scores were positively correlated with MCP-1 levels across all patients. There were no differences between sequential FLACS in miosis, PGE2, IL-6, IL-8 levels and changes in postoperative ECD, CCT, and CST. Patients who underwent second-eye FLACS after 6 weeks showed more CCT, CST, and MCP-1 changes than baseline. CONCLUSION: Second-eye FLACS causes more pain and upregulated MCP-1. There was no difference between sequential FLACS in PGE2 levels, miosis, and postoperative inflammation. Furthermore, first-eye FLACS triggered a sympathetic irritation, particularly after a 6-week interval.

Logic Computing Field-Effect Transistors Based on a Monolayer WSe2 Homojunction for the Semi-adder and Decoder.

Two-dimensional reconfigurable field-effect transistors (FETs) are promising candidates for next-generation computing hardware. However, exploring the cascade design of FETs for logic computing remains challenging. Here, by using density functional theory combined with the nonequilibrium Green's function method, we design a 5 nm split-gate FET based on a monolayer WSe2 homojunction, which can implement dynamic polarity control in different gate configurations. The series array of two FETs shows a functional family of logic gates (NOR, AND, XOR, A̅B, and AB̅), and the semi-adder designed by the logic functions AND and XOR reduces the number of transistors by 66.7%. The parallel array of two FETs demonstrates reconfigurable logic gates with NAND/OR/A̅+B/A+B̅ quadruple functions, which can realize the decoding function of 00-11 in the decoder. The cascade design of the electrically tunable FETs helps to tackle the logic device downscaling and integration dilemmas.

Suppressing a ß-1,3-glucanase gene expression increases the seed and fibre yield in cotton.

Seeds are initiated from the carpel margin meristem (CMM) and high seed yield is top one of breeding objectives for many crops. ß-1,3-glucanases play various roles in plant growth and developmental processes; however, whether it participates in CMM development and seed formation remains largely unknown. Here, we identified a ß-1,3-glucanase gene (GLU19) as a determinant of CMM callose deposition and seed yield in cotton. GLU19 was differentially expressed in carpel tissues between Gossypium barbadense (Gb) and Gossypium hirsutum (Gh). Based on resequencing data, one interspecies-specific InDel in the promoter of GLU19 was further detected. The InDel was involved in the binding site of the CRABS CLAW (CRC) transcription factor, a regulator of carpel development. We found that the CRC binding affinity to the GLU19 promoter of G. barbadense was higher than that of G. hirsutum. Since G. barbadense yields fewer seeds than G. hirsutum, we speculated that stronger CRC binding to the GLU19 promoter activated higher expression of GLU19 which in turn suppressed seed production. Consistent with this hypothesis was that the overexpression of GhGLU19 caused reduced seed number, boll weight and less callose formation in CMM. Conversely, GhGLU19-knockdown (GhGLU19-KD) cotton led to the opposite phenotypes. By crossing GhGLU19-KD lines with several G. hirsutum and G. barbadense cotton accessions, all F1 and F2 plants carrying GhGLU19-KD transgenic loci exhibited higher seed yield than control plants without the locus. The increased seed effect was also found in the down-regulation of Arabidopsis orthologs lines, indicating that this engineering strategy may improve the seed yield in other crops.

Probing spin hydrodynamics on a superconducting quantum simulator.

Characterizing the nature of hydrodynamical transport properties in quantum dynamics provides valuable insights into the fundamental understanding of exotic non-equilibrium phases of matter. Experimentally simulating infinite-temperature transport on large-scale complex quantum systems is of considerable interest. Here, using a controllable and coherent superconducting quantum simulator, we experimentally realize the analog quantum circuit, which can efficiently prepare the Haar-random states, and probe spin transport at infinite temperature. We observe diffusive spin transport during the unitary evolution of the ladder-type quantum simulator with ergodic dynamics. Moreover, we explore the transport properties of the systems subjected to strong disorder or a tilted potential, revealing signatures of anomalous subdiffusion in accompany with the breakdown of thermalization. Our work demonstrates a scalable method of probing infinite-temperature spin transport on analog quantum simulators, which paves the way to study other intriguing out-of-equilibrium phenomena from the perspective of transport.

Research on a Support-Free Five-Degree-of-Freedom Additive Manufacturing Method.

When using traditional 3D printing equipment to manufacture overhang models, it is often necessary to generate support structures to assist in the printing of parts. The post-processing operation of removing the support structures after printing is time-consuming and wastes material. In order to solve the above problems, a support-free five-degree-of-freedom additive manufacturing (SFAM) method is proposed. Through the homogeneous coordinate transformation matrix, the forward and inverse kinematics equations of the five-degree-of-freedom additive manufacturing device (FAMD) are established, and the joint variables of each axis are solved to realize the five-axis linkage of the additive manufacturing (AM) device. In this research work, initially, the layered curve is obtained through the structural lines of the overhang model, and a continuous path planning of the infill area is performed on it, and further, the part printing experiments are conducted on the FAMD. Compared with the traditional three-axis additive manufacturing (TTAM) method, the SFAM method shortens the printing time by 23.58% and saves printing materials by 33.06%. The experimental results show that the SFAM method realizes the support-free printing of overhang models, which not only improves the accuracy of the parts but also the manufacturing efficiency of the parts.

Molybdenum single-atoms decorated multi-channel carbon nanofibers for advanced lithium-selenium batteries.

The cathode in lithium-selenium (Li-Se) batteries has garnered extensive attention owing to its superior specific capacity and enhanced conductivity compared to sulfur. Nonetheless, the adoption and advancement of Li-Se batteries face significant challenges due to selenium's low reactivity, substantial volume fluctuations, and the shuttle effect associated with polyselenides. Single-atom catalysts (SACs) are under the spotlight for their outstanding catalytic efficiency and optimal atomic utilization. To address the challenges of selenium's low chemical activity and volume expansion in Li-Se batteries, through electrospun, we have developed a lotus root-inspired carbon nanofiber (CNF) material, featured internal multi-channels and anchored with molybdenum (Mo) single atoms (Mo@CNFs). Mo single atoms significantly enhance the conversion kinetics of selenium (Se), facilitating rapid formation of Li2Se. The internally structured multi-channel CNF serves as an effective host matrix for Se, mitigating its volume expansion during the electrochemical process. The resulting cathode, Se/Mo@CNF composite, exhibits a high discharge specific capacity, superior rate performance, and impressive cycle stability in Li-Se batteries. After 500 cycles at a current density of 1 C, it maintains a capacity retention rate of 82% and nearly 100% coulombic efficiency (CE). This research offers a new avenue for the application of single-atom materials in enhancing advanced Li-Se battery performance.

Unraveling nanosprings: morphology control and mechanical characterization.

Nanosprings demonstrate promising mechanical characteristics, positioning them as pivotal components in a diverse array of potential nanoengineering applications. To unlock the full potential of these nanosprings, ongoing research is concentrated on emulating springs at the nanoscale in terms of both morphology and function. This review underscores recent advancements in the field and provides a comprehensive overview of the diverse methods employed for nanospring preparation. Understanding the general mechanism behind nanospring formation lays the groundwork for the informed design of nanosprings. The synthesis section delineates four prominent methods employed for nanospring fabrication: vapor phase synthesis, templating methods, post-treatment techniques, and molecular engineering. Each method is critically analyzed, highlighting its strengths, limitations, and potential for scalability. Mechanical properties of nanosprings are explored in depth, discussing their response to external stimuli and their potential applications in various fields such as sensing, energy storage, and biomedical engineering. The interplay between nanospring morphology and mechanical behavior is elucidated, providing insights into the design principles for tailored functionality. Additionally, we anticipate that the evolution of state-of-the-art characterization tools, such as in situ transmission electron microscopy, 3D electron tomography, and machine learning, will significantly contribute to both the study of nanospring mechanisms and their applications.

Fourteen-Day Tegoprazan-Amoxicillin Dual Therapy as the First-Line Treatment of Helicobacter pylori Infection (SHARE2301): A Multicenter, Noninferiority, Randomized Clinical Trial.

BACKGROUND: Potassium-competitive acid blockers have demonstrated enormous potential in the eradication treatment of Helicobacter pylori infection, with tegoprazan being one of the representatives. The available data on the safety and efficacy of tegoprazan in dual therapy are limited. MATERIALS AND METHODS: The multicenter, noninferiority, randomized-controlled trial was conducted from May 2023 to March 2024. Treatment-naive subjects were randomly assigned (1:1) to enter either the tegoprazan-amoxicillin (TA) group (tegoprazan 50 mg twice daily and amoxicillin 750 mg four times daily) or the esomeprazole-amoxicillin (EA) group (esomeprazole 20 mg and amoxicillin 750 mg all four times daily), with a duration for 14 days. The primary outcome was eradication rate as determined by 13C-urea breath test, including per-protocol (PP) analysis and intention-to-treat (ITT) analysis. Secondary outcomes were adverse events and compliance. RESULTS: A total of 368 individuals were included in the randomization. The eradication rates in the EA group and the TA group were 84.2% and 85.8%, respectively, according to an ITT analysis (p = 0.77), and 88.5% and 88.2%, respectively, according to PP analysis (p = 1.00). The eradication rates for the TA group were not inferior to those of the EA group in both PP (p = 0.0023) and ITT analyses (p = 0.0009). There were no significant statistical differences in the incidence of adverse events and compliance between the two groups. The multivariate logistic regression analysis revealed that poor compliance increased the risk of eradication failure (p < 0.001). CONCLUSIONS: Dual therapy containing tegoprazan is safe and effective to be considered as a clinical first-line treatment option, but further optimization involving antimicrobial susceptibility testing and adjustments in dosage and frequency is warranted. TRIAL REGISTRATION: ClinicalTrials.gov ID: NCT05870683.

Bismuth-Containing Quadruple Therapy for Helicobacter pylori Eradication: A Randomized Clinical Trial of 10 and 14 Days.

BACKGROUND: Bismuth-containing quadruple therapy is the first-line treatment for eradicating Helicobacter pylori (H. pylori). The optimal duration for H. pylori eradication using bismuth-containing quadruple therapy remains controversial. Therefore, we aimed to compare the clinical effects of the 10- and 14-day bismuth-containing quadruple treatment regimen to eradicate H. pylori. METHODS: Treatment-naïve patients with H. pylori infection (n = 1300) were enrolled in this multicenter randomized controlled study across five hospitals in China. They were randomized into 10- or 14-day treatment groups to receive bismuth-containing quadruple therapy as follows: vonoprazan 20 mg twice daily; bismuth 220 mg twice daily; amoxicillin 1000 mg twice daily; and either clarithromycin 500 mg twice daily or tetracycline 500 mg four times daily. At least 6 weeks after treatment, we performed a 13C-urea breath test to evaluate H. pylori eradication. RESULTS: The per-protocol eradication rates were 93.22% (564/605) and 93.74% (569/607) (p < 0.001) and the intention-to-treat eradication rates were 88.62% (576/650) and 89.38% (581/650) (p = 0.007) for the 10- and 14-day regimens, respectively. Incidence of adverse effects was lower in patients who received 10- vs. 14 days of treatment (22.59% vs. 28.50%, p = 0.016). We observed no significant differences in the compliance to treatment or the discontinuation of therapy because of severe adverse effects between the groups. CONCLUSION: Compared with the 14-day bismuth-containing quadruple regimens, the 10-day regimen demonstrated a non-inferior efficacy and lower incidence of adverse effects. Therefore, the 10-day regimen is safe and tolerated and could be recommended for H. pylori eradication (NCT05049902).

Sustainable reprocessing of lithium iron phosphate batteries: A recovery approach using liquid-phase method at reduced temperature.

Lithium iron phosphate batteries, known for their durability, safety, and cost-efficiency, have become essential in new energy applications. However, their widespread use has highlighted the urgency of battery recycling. Inadequate management could lead to resource waste and environmental harm. Traditional recycling methods, like hydrometallurgy and pyrometallurgy, are complex and energy-intensive, resulting in high costs. To address these challenges, this study introduces a novel low-temperature liquid-phase method for regenerating lithium iron phosphate positive electrode materials. By using N2H4·H2O as a reducing agent, missing Li+ ions are replenished, and anti-site defects are reduced through annealing. This process restores nearly all missing Li+ ions at 80 °C/6h. After high-temperature sintering at 700 °C/2h, the regenerated LiFePO4 matches commercial LiFePO4 in terms of anti-site defects and exhibits excellent performance with a 97 % capacity retention rate after 100 cycles at 1C. Compared to high-temperature techniques, this low-temperature liquid-phase method is simpler, safer, and more energy-efficient, offering a blueprint for reclaiming discarded LiFePO4 and similar materials.

Clinical use of macitentan in the treatment of connective tissue disease-associated pulmonary arterial hypertension.

Background: Connective tissue disease (CTD) is the second most common cause of the pulmonary arterial hypertension (PAH). Currently, clinical data concerning CTD-PAH is scarce. Our study aimed to assess the efficacy and safety of macitentan in the treatment of CTD-PAH. Methods: In this retrospective study, patients diagnosed with CTD-PAH at The First Affiliated Hospital of Soochow University from April 2020 to November 2021 were included. Of the patients, 9 were switched to macitentan monotherapy whereas 23 received initial combination therapy. The mean follow-up time was 24 weeks. Six-minute walking distance (6MWD), World Health Organization functional class (WHO-FC), serum N-terminal pro-brain natriuretic peptide (NT-proBNP), and echocardiography parameters before and after medication were assessed. Adverse reactions were also recorded and compared. Results: After 24 weeks of treatment, 6MWD, NT-proBNP, systolic pulmonary artery pressure (sPAP) estimated by ultrasound, tricuspid regurgitation pressure gradient (TRPG) and tricuspid annular plane systolic excursion (TAPSE) in the macitentan monotherapy group revealed significant differences (Z=-2.67, Z=-2.67, t=6.20, t=5.60, t=-3.04, P<0.05). There were no statistically significant differences in right ventricular diameter (RVD), right atrial diameter (RAD), ascending aortic root inner diameter (AAO) and left ventricular end-diastolic diameter (LVEDd) (P>0.05). After 24 weeks of medication, the number of patients with WHO-FC grade III/IV symptoms decreased from 6 to 3, 1 to 0 respectively (P<0.05), and that of patients with WHO-FC grade I/II symptoms increased from 0 to 2, 2 to 4 respectively(P<0.05). After 24 weeks of treatment, 6MWD, NT-proBNP, LVEDd, sPAP and TRPG in the macitentan combined with sildenafil treatment group revealed statistically significant differences (Z=-4.11, Z=-3.74, Z=-3.83, t=6.88, t=6.54, P<0.001). Significant differences in RVD, RAD, and TAPSE were found (t=3.46, t=3.69, t=-3.12, P<0.05). There were no statistically significant variances in AAO between the groups (P>0.05). The number of patients with WHO-FC grade III/IV symptoms decreased from 16 to 8, 5 to 0 respectively (P<0.05), and that of patients with WHO-FC grade I/II symptoms increased from 0 to 1, 2 to 14 respectively (P<0.001). There were no statistically significant differences before and after treatment in 6MWD, NT-proBNP, RVD, RAD, AAO, LVEDd, sPAP, TRPG and TAPSE between the two groups (P>0.05). There were no statistically significant differences in alanine aminotransferase (ALT), aspartate aminotransferase (AST), serum creatinine (Scr) and hemoglobin (Hb) between 0 and 24 weeks (P>0.05). Conclusions: Exercise tolerance and cardiac function in patients with CTD-PAH were significantly improved after treatment with macitentan, which was well tolerated. Therefore, macitentan may be an effective and safe targeted drug for CTD-PAH.

Innovative Solutions for High-Performance Silicon Anodes in Lithium-Ion Batteries: Overcoming Challenges and Real-World Applications.

Silicon (Si) has emerged as a potent anode material for lithium-ion batteries (LIBs), but faces challenges like low electrical conductivity and significant volume changes during lithiation/delithiation, leading to material pulverization and capacity degradation. Recent research on nanostructured Si aims to mitigate volume expansion and enhance electrochemical performance, yet still grapples with issues like pulverization, unstable solid electrolyte interface (SEI) growth, and interparticle resistance. This review delves into innovative strategies for optimizing Si anodes' electrochemical performance via structural engineering, focusing on the synthesis of Si/C composites, engineering multidimensional nanostructures, and applying non-carbonaceous coatings. Forming a stable SEI is vital to prevent electrolyte decomposition and enhance Li+ transport, thereby stabilizing the Si anode interface and boosting cycling Coulombic efficiency. We also examine groundbreaking advancements such as self-healing polymers and advanced prelithiation methods to improve initial Coulombic efficiency and combat capacity loss. Our review uniquely provides a detailed examination of these strategies in real-world applications, moving beyond theoretical discussions. It offers a critical analysis of these approaches in terms of performance enhancement, scalability, and commercial feasibility. In conclusion, this review presents a comprehensive view and a forward-looking perspective on designing robust, high-performance Si-based anodes the next generation of LIBs.

Combined genome and transcriptome analysis of elite fiber quality in Gossypium barbadense.

Gossypium barbadense, which is one of several species of cotton, is well known for its superior fiber quality. However, the genetic basis of its high-quality fiber remains largely unexplored. Here, we resequenced 269 G. barbadense accessions. Phylogenetic structure analysis showed that the set of accessions was clustered into 3 groups: G1 and G2 mainly included modern cultivars from Xinjiang, China, and G3 was related to widely introduced accessions in different regions worldwide. A genome-wide association study of 5 fiber quality traits across multiple field environments identified a total of 512 qtls (main-effect QTLs) and 94 qtlEs (QTL-by-environment interactions) related to fiber quality, of which 292 qtls and 57 qtlEs colocated with previous studies. We extracted the genes located in these loci and performed expression comparison, local association analysis, and introgression segment identification. The results showed that high expression of hormone-related genes during fiber development, introgressions from Gossypium hirsutum, and the recombination of domesticated elite allelic variation were 3 major contributors to improve the fiber quality of G. barbadense. In total, 839 candidate genes with encoding region variations associated with elite fiber quality were mined. We confirmed that haplotype GB_D03G0092H traced to G. hirsutum introgression, with a 1-bp deletion leading to a frameshift mutation compared with GB_D03G0092B, significantly improved fiber quality. GB_D03G0092H is localized in the plasma membrane, while GB_D03G0092B is in both the nucleus and plasma membrane. Overexpression of GB_D03G0092H in Arabidopsis (Arabidopsis thaliana) significantly improved the elongation of longitudinal cells. Our study systematically reveals the genetic basis of the superior fiber quality of G. barbadense and provides elite segments and gene resources for breeding high-quality cotton cultivars.

A novel intraocular pressure predicting method based on hyperelastic mechanical model of cornea.

Measuring intraocular pressure (IOP) is crucial and remains challenging in diagnosing glaucoma, as it is associated with cornea deformation during inflation. In this study, a three-dimensional analytical model based on hyperelastic constitutive relationship to predict correlation between cornea vertex displacement and the IOP is proposed. The analytical model is validated by rigorous experiments. Rabbit corneas were selected for this study and their mechanical properties were obtained using uniaxial tensile tests. To mimic the environment in which the cornea exists, an artificial anterior chamber equipped with water-injection pipelines was constructed to study the relationship between the corneal vertex displacement with IOP value in practical situation. The experimental results of rabbits corneas prove that the IOP can be deduced based on the measured corneal vertex displacement by the analytical model. Furthermore, subtle difference occurs when comparing the calculated human IOPs with those measured by medical equipment, demonstrating that the proposed method is suitable for monitoring the IOP of human. This novel IOP predicting method provides new inspiration for the design of eyepieces, as well as the preoperative preparation for laser surgery and evaluation of corneal damage.

Revealing microscopic dynamics: in situ liquid-phase TEM for live observations of soft materials and quantitative analysis via deep learning.

In various domains spanning materials synthesis, chemical catalysis, life sciences, and energy materials, in situ transmission electron microscopy (TEM) methods exert a profound influence. These methodologies enable the real-time observation and manipulation of gas-phase and liquid-phase reactions at the nanoscale, facilitating the exploration of pivotal reaction mechanisms. Fundamental research areas like crystal nucleation, growth, etching, and self-assembly have greatly benefited from these techniques. Additionally, their applications extend across diverse fields such as catalysis, batteries, bioimaging, and drug delivery kinetics. However, the intricate nature of 'soft matter' presents a challenge due to the unique molecular properties and dynamic behavior of these substances that remain insufficiently understood. Investigating soft matter within in situ liquid-phase TEM settings demands further exploration and advancement compared to other research domains. This research harnesses the potential of in situ liquid-phase TEM technology while integrating deep learning methodologies to comprehensively analyze the quantitative aspects of soft matter dynamics. This study centers on diverse phenomena, encompassing surfactant molecule nucleation, block copolymer behavior, confinement-driven self-assembly, and drying processes. Furthermore, deep learning techniques are employed to precisely analyze Ostwald ripening and digestive ripening dynamics. The outcomes of this study not only deepen the understanding of soft matter at its fundamental level but also serve as a pivotal foundation for developing innovative functional materials and cutting-edge devices.

Effect of SARS-CoV-2 infection on semen parameters in sperm bank volunteers with normal sperm concentration.

In this study, we aimed to assess the effect of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) infection on semen parameters. The study comprised 110 sperm volunteers who self-reported SARS-CoV-2 infection from the Human Sperm Bank of the Center for Reproductive Medicine, Shandong University (Jinan, China). The volunteers had normal sperm concentration before infection. Each volunteer provided semen samples before and after infection. We selected 90 days after infection as the cutoff point. Semen parameters within 90 days after infection of 109 volunteers (group A) were compared with semen parameters before infection. Moreover, semen parameters on or after 90 days after infection of 36 volunteers (group B) were compared with semen parameters before infection. Furthermore, based on whether the volunteers had completed the three-dose SARS-CoV-2 vaccination booster, volunteers in group A and B were further divided into two subgroups separately. Semen parameters were compared before and after infection in each subgroup. Our results showed that in this cohort population, the semen quality in volunteers with normal sperm concentrations before infection decreased after SARS-CoV-2 infection within 90 days, while the semen quality returned to preinfection levels after 90 days. The completion of a three-dose SARS-CoV-2 vaccination booster may exert a protective effect on semen quality after infection.

Development of a Real-Time qPCR Method for the Clinical Sample Detection of Capripox Virus.

Capripox viruses (CaPVs), including sheep pox virus (SPV), goat pox virus (GPV), and lumpy skin disease virus (LSDV), are the cause of sheep pox (SPP), goat pox (GTP), and lumpy skin disease (LSD) in cattle. These diseases are of great economic significance to farmers, as they are endemic on farms and are a major constraint to international trade in livestock and their products. Capripoxvirus (CaPV) infections produce similar symptoms in sheep and goats, and the three viruses cannot be distinguished serologically. In this study, we developed a real-time quantitative polymerase chain reaction (qPCR) method for identifying CaPV in goats, sheep, and cattle. Clinical samples were tested and verified. The developed assay was highly specific for target viruses, including GPVSPV and LSDV, which had no cross-reaction with other viruses causing similar clinical symptoms. An artificially synthesized positive control plasmid using the CaPV 32 gene inserted into the vector pMD19-T was used as a template, and the correlation coefficient of the linear regression curve (R2) was 0.9916, the estimated amplification efficiency (E) was 96.06%, and the sensitivity (limit of detection, LOD) was 3.80 copies per reaction. Using the clinical samples as a template, the limit of detection (LOD) was 4.91 × 10-5 ng per reaction (1.60 × 10-5-2.13 × 10-3 ng, 95% confidence interval (CI)), which means that this method was one of the most sensitive detection assays for CaPVs. A total of 85 clinical samples from CaPV-infected animals (goats, sheep, and cattle) and 50 clinical samples from healthy animals were used to test and compare the diagnostic results using the Synergy Brands (SYBR) Green-based PCR method recommended by the World Organization of Animal Health (WOAH). Both diagnostic sensitivity (DSe) (95.8-100%, 95% CI) and diagnostic specificity (DSp) (92.9-100%, 95% CI) results of the real-time quantitative PCR (qPCR) and SYBR Green PCR were 100%, and the kappa value (κ) was 1.0 (1-1, 95% CI). In summary, the assay established based on TaqMan probes was advantageous in high specificity, sensitivity, and general applicability and could be a competitive candidate tool for the diagnosis of CaPV in clinically suspected animals.

Design and Processing of Gas Turbine Blades Based on Additive Manufacturing Technology.

Aiming at the problems of the complex shape, difficult three-dimensional (3D) digital modeling and high manufacturing quality requirements of gas turbine blades (GTB), a method of fitting the blade profile line based on a cubic uniform B-spline interpolation function was proposed. Firstly, surface modeling technology was used to complete the fitting of the blade profile of the GTB, and the 3D model of the GTB was synthesized. Secondly, the processing parameters of the additive manufacturing were set, and the GTB model was printed by fused deposition technology. Then, the rapid investment casting was completed with the printed model as a wax model to obtain the GTB casting. Finally, the blade casting was post-processed and measured, and it was found to meet the requirements of machining accuracy and surface quality.