Study on the Micro-Abrasion Wear Behavior of PVD Hard Coating under Different SiC Abrasive Particles/Distilled Water Ratios.

Microscale abrasion has been intensively used to study the wear behavior o several hard coatings, enabling the observation of different wear mechanisms. Recently, a study arguing whether the surface texture of the ball could influence the dynamics of abrasive particles throughout the contact was presented. In this work, the influence of the abrasive particles concentration able to change the texture of the ball was studied to understand its influence on the wear modes-rolling or grooving. Thus, tests were carried out using samples with a thin coating of TiN, deposited using the Physical Vapor Deposition (PVD) technique, and AISI 52100 steel balls etched over 60 s to induce a change in their texture and roughness were used. Three abrasive slurries were prepared with black silicon carbide (SiC) particles (average particle size of 4 µm) with different concentrations, 0.25, 0.35, and 0.45 g/cm3. The rotation speed used in the tests was 80 rpm and the normal loads applied in the study were 0.2 N and 0.5 N, and 1 N. After the wear tests, the coated samples and tracks on the surface of the balls were observed by SEM and 3D microscopy to understand the abrasive particle dynamics, evaluating the wear mode transition as well as the function of both applied load and slurry concentration. The tracks in the balls showed particles embedded on their surface. A lower concentration of abrasion was conducted to higher specific wear rate. Moreover, a predominant two-body wear mechanism was induced when the abrasive concentration was increased. There was an increase in the roughness of the scar and the surface of the balls with an increase in the abrasive particles' concentration.

Study of the Chlorine Influence on the Corrosion of Three Steels to Be Used in Water Treatment Municipal Facilities.

Many municipal facilities, such as pools and drinking water treatment facilities, are subject to ongoing maintenance due to the corrosion of their metallic materials caused by chlorine, leading to high costs and a possible risk to public health. A proper study of the employed product's effect could lead to the use of better materials, which significantly increase the lifetime of metallic equipment more attacked by corrosion, through studies evaluating their cost-effectiveness. This paper was carried out with the objective of studying the degradation of some metallic materials (AISI 316L, AISI 321 and Duplex 14462) used in the referred facilities in order to select the one that possessed a better behavior. It was observed that the introduction of some more adequate materials can drastically reduce maintenance operations, with Duplex 14462 showing the best results, ideal for greater chlorine concentrations, followed by AISI 321, which may be employed for components in less contact with chlorine, since it is more easily affordable.

The Impact of the Deterioration on Wood by Chlorine: An Experimental Study.

The use of disinfection and cleaning chemicals in several municipal facilities, such as swimming pools and drinking water treatment plants, causes the degradation of various types of wood, which leads to failures in equipment and the corresponding need for maintenance. This degradation creates added costs for municipalities, as well as the closure of certain facilities due to curative or preventive maintenance and, in many cases, public health issues, due to the water being contaminated with deteriorating products. Through a thorough study of the degradation effect on the products, more resistant materials can be found which are able to withstand these adversities and increase the lifespan of wood in regular contact with chemical agents. This is achievable by the determination of the cost-effectiveness of the substitute material to replace these components with alternative ones, with properties that better resist the deterioration effects promoted by aggressive environments. No studies have been found so far strictly focused on this matter. The objective of this study is to evaluate the degradation presented by two types of wood, beech and oak, which are exposed to the action of chlorine in municipal facilities. This degradation varies according to the chlorine content and the materials' time of contact with the chemical agent, allowing the selection of new materials which will provide an extended lifetime of the components, reducing maintenance drastically, as well as costs for the facilities and the risk to public health. The performed experimental tests have shown that the oak wood has the best results regarding chlorine degradation resistance.

Wear Behavior and Machining Performance of TiAlSiN-Coated Tools Obtained by dc MS and HiPIMS: A Comparative Study.

Duplex stainless steels are being used on applications that require high corrosion resistance and excellent mechanical properties, such as the naval and oil-gas exploration industry. The components employed in these industries are usually obtained by machining; however, these alloys have low machinability when compared to conventional stainless steels, usually requiring the employment of tool coatings. In the present work, a comparative study of TiAlSiN coating performance obtained by these two techniques in the milling of duplex stainless-steel alloy LDX 2101 was carried out. These coatings were obtained by the conventional direct current magnetron sputtering (dc MS) and the novel high power impulse magnetron sputtering (HiPIMS). The coatings were analyzed and characterized, determining mechanical properties for both coatings, registering slightly higher mechanical properties for the HiPIMS-obtained coating. Machining tests were performed with varying cutting length and feed-rate, while maintaining constant values for axial and radial depth of cut and cutting speed. The surface roughness of the material after machining was assessed, as well as the wear sustained by each of the tool types, identifying the wear mechanisms and behavior of these tools, as well as registering the flank wear values presented for each of the tested tools. The HiPIMS-obtained coating exhibited a very similar behavior when compared to the other, producing similar surface roughness quality. However, the HiPIMS coating exhibited less wear for higher cutting lengths, proving to be a better choice in this case, especially regarding tool life.

Cutting Forces Assessment in CNC Machining Processes: A Critical Review.

Machining processes remain an unavoidable technique in the production of high-precision parts. Tool behavior is of the utmost importance in machining productivity and costs. Tool performance can be assessed by the roughness left on the machined surfaces, as well as of the forces developed during the process. There are various techniques to determine these cutting forces, such as cutting force prediction or measurement, using dynamometers and other sensor systems. This technique has often been used by numerous researchers in this area. This paper aims to give a review of the different techniques and devices for measuring the forces developed for machining processes, allowing a quick perception of the advantages and limitations of each technique, through the literature research carried out, using recently published works.

Effects of musical cadence in the acute physiologic adaptations to head-out aquatic exercises.

The purpose of this study was to analyze the relationships between musical cadence and the physiologic adaptations to basic head-out aquatic exercises. Fifteen young and clinically healthy women performed, immersed to the breast, a cardiovascular aquatic exercise called the "rocking horse." The study design included an intermittent and progressive protocol starting at a 90 b.min(-1) rhythm and increasing every 6 minutes, by 15 b.min(-1), up to 195 b.min(-1) or exhaustion. The rating of perceived effort (RPE) at the maximal heart rate achieved during each bout (HRmax), the percentage of the maximal theoretical heart rate estimated (%HRmax), and the blood lactate concentration ([La-]) were evaluated. The musical cadence was also calculated at 4 mmol.L(-1) of blood lactate (R4), the RPE at R4 (RPE@R4), the HR at R4 (HR@R4), and the %HRmax at R4 (%HRmax@R4). Strong relationships were verified between the musical cadence and the RPE (R2 = 0.85; p < 0.01), the HRmax (R2 = 0.66; p < 0.01), the %HRmax (R = 0.61; p < 0.01), and the [La-] (R2 = 0.54; p < 0.01). The R4 was 148.13 +/- 17.53 b.min, the RPE@R4 was 14.53 +/- 2.53, the HR@R4 was 169.33 +/- 12.06 b.min, and the %HRmax@R4 was 85.53 +/- 5.72%. The main conclusion is that increasing musical cadence created an increase in the physiologic response. Therefore, instructors must choose musical cadences according to the goals of the session they are conducting to achieve the desired intensity.