Influence of build direction, post-polymerization time, and aging on the fracture resistance and marginal and internal discrepancies of three-dimensional printed provisional crowns.

To evaluate the effect of build direction, post-polymerization time, and aging on the fracture resistance, failure mode, margin quality and Marginal (MD) and Internal Discrepancies (ID), and degree of conversion of tridimensional (3D) printed provisional crowns using the liquid crystal display technique (LCD). A left mandibular first molar was prepared and scanned. After, a full crown was designed (ExoCad) and exported to the LCD-printer software. One hundred and eighty crowns were printed at two build directions (30°, 90°) and post-polymerized for different periods (15, 30, 45 min). Half of the samples were aged (ST) in distilled water (37 °C/90 days). The marginal quality of the crowns was evaluated by the Schriwer method under a stereomicroscope (40x). The replica technique was used to measure the MD and ID and measured under a stereomicroscope (10x), through 20 reference points defined in 5 regions: Occlusal (O), Cusp (CP), Axial (AX), Chamfer (CH), and Finish Line (F). After, the crowns were cemented onto the respective dies using temporary cement and submitted to compression test (ISO150, 1 mm/min, 100 kgf).The failure mode was classified by Burke's fracture mode. The degree of conversion was evaluated through Fourier Transform Infrared Spectroscopy. The data (µm) of MD and ID and fracture resistance (N) were subjected to ANOVA (3 factors) and Tukey's test (5%); Weibull analysis was also performed for fracture resistance data (N). For MD, ID and fracture resistance ANOVA revealed that all factors (P < .001) were significant. For aged groups, the crowns printed at 30° showed lower MD (Tukey). The O_90_30 min (172.13A µm) and O_90_15 min (170.20A µm) groups showed the highest ID values. Higher resistance values were observed for the 30_45 min (844.30A N), 30_30 min (835.35A N), and 90_30 min (820.62A N) groups (Tukey). In the margin analysis, 98.6% of the crowns printed at 30° showed smooth margins without defects. The most prevalent fracture mode (41.7%) was Burke type 5. The degree of conversion (DC) increased with increasing post-polymerization time and aging. Printing provisional crowns at 30° provided lower crown MD and ID, as well as higher fracture resistance. A post-polymerization time of 30 min resulted in higher crown fracture resistance, while aging reduced the resistance of the crowns.

Effect of different surface treatments and adhesive cementation on the surface topography and flexural strength of translucent and ultra-translucent monolithic zirconia.

PURPOSE: To evaluate the effect of different surface treatments and adhesive cementation on the miniflexural strength (MFS) of monolithic zirconia. MATERIALS AND METHODS: Two-hundred and forty (240) sintered bars of translucent zirconia (ZT) and ultra-translucent zirconia (ZUT) were obtained (8 mm ×2 mm ×1 mm). The bars were divided into 16 groups (n = 15) according to the factors "Zirconia" (ZT and ZUT), "Cementation" (Cem) and "surface treatment" (Ctrl:Control, Al:Aluminum oxide/Al2O3 50 µm, Si:Silica/SiO2 coated alumina particles oxide 30 µm, Gl:Glazing+hydrofluoric acid). Half of the bars received an adhesive layer application, followed by application of resin cement and light curing. The surface roughness was measured in non-cemented groups. All the bars were subjected to the MFS test (1.0 mm/min; 100 kgf). Scanning electron microscopy was used for qualitative analyses. MFS data (MPa) and roughness (µm) were statistically evaluated by three-way and two-way ANOVA respectively and Tukey's test (5%). RESULTS: The surface treatment and the interaction were significant for roughness. Glazing promoted less roughness compared to silicatization. Regarding MFS, only the zirconia and surface treatment factors were significant. For ZT, the sandblasted groups had an increase in MFS and glazing reduced it. There was no difference between the groups without cementation for the ZUT; however, ZUT.Si/Cem, and ZUT.Al/Cem obtained superior MFS among the cemented groups. CONCLUSIONS: Sandblasting increases the flexural strength for ZT, while glaze application tends to reduce it. Applying resin cement increases the flexural strength of ZUT when associated with sandblasting. Sandblasting protocols promote greater surface roughness.

Continuous Flow Synthesis of Hexyl Laurate Using Immobilized Thermomyces Lanuginosus Lipase from Residual Babassu Mesocarp.

This work applied BM as support for immobilization of lipase TLL in packed-bed reactor and its application for the synthesis of hexyl laurate. Initially, the percolation of a solution containing 5 mg of TLL at 25 oC generated an immobilized derivative with hydrolytic activity of 504.7 U/g and 31.7% of recovered activity. Subsequent treatment with n-hexane, as well as the effect of temperature on the immobilization process were able to improve the activities of the final BM-TLLF, achieving a hydrolysis activity of 7023 U/g and esterification activity of 430 U/g against 142 U/g and 113.5 U/g respectively presented by commercial TLIM. Desorption studies showed that the TL IM has 18 mg of protein per gram of support, compared to 4.92 mg presented by BM-TLL. Both biocatalysts were applied to synthesize hexyl laurate, achieving 98% conversion at 40°C within a residence time of 2 hours. Notably, BM-TLLF displayed exceptional recyclability, maintaining catalytic efficiency over 12 cycles. This reflects a productivity of 180 mg of product/h/U of the enzyme, surpassing 46 mg/h/U obtained for TLIM. These results demonstrate the efficacy of continuous flow technology in creating a competitive and integrated process offering an exciting alternative for the valorization of residual lignocellulosic biomass.

Three-dimensional models of physeal fractures in the femur for the teaching of veterinary medicine.

PURPOSE: To develop and assess three-dimensional models of physeal fractures in dog femurs (3D MPFDF) using radiographic imaging. METHODS: The study was conducted in three phases: development of 3D MPFDF; radiographic examination of the 3D MPFDF; and comparative analysis of the anatomical and radiographic features of the 3D MPFDF. RESULTS: The base model and the 3D MPFDF achieved high fidelity in replicating the bone structures, accurately maintaining the morphological characteristics and dimensions such as length, width, and thickness, closely resembling natural bone. The radiographs of the 3D MPFDF displayed distinct radiopaque and radiolucent areas, enabling clear visualization of the various anatomical structures of the femur. However, in these radiographs, it was challenging to distinguish between the cortical and medullary regions due to the use of 99% internal padding in the printing process. Despite this limitation, the radiographs successfully demonstrated the representation of the Salter-Harris classification. CONCLUSIONS: This paper presents a pioneering project focused on technological advancement aimed at developing a method for the rapid and cost-effective production of three-printed models and radiographs of physeal fractures in dogs.

Effect of time and photoactivated face on bond strength of brackets and on degree of monomer conversion.

OBJECTIVE: To evaluate the effect of four different photoactivation protocols (according to "photoactivated faces" - mesial/distal, cervical/incisal or center - and "photoactivation time" - 6-3 s) of a high-power photo activator (Valo Cordless®-Ultradent) on the shear bond strength (SBS) between metal brackets and dental enamel and on the degree of conversion (DC) of an orthodontic resin. MATERIALS AND METHODS: 40 bovine incisor crowns were randomly assigned to 4 groups (n = 10). The brackets were bonded with Transbond XT® resin using 4 protocols according to the "photoactivation protocol" factor (which was subdivided into photoactivated faces and photoactivation time): V3C = 3 s + center; V6C = 6 s + center; V3M3D = 3 s on mesial + 3 s on distal; V3C3I = 3 s on cervical + 3 s on incisal. All the samples were stored for 4 months (water,37ºC) and then subjected to a SBS test (100KgF,1 mm/min). 40 resin discs were made to evaluate the monomer degree of conversion. Data from the SBS and DC were assessed by One-way ANOVA and Tukey's test (5%). Bond failures were analyzed according to the Adhesive Remnant Index (ARI) and evaluated by the Kruskal-Wallis test (5%). RESULTS: There was a statistically significant difference (p = 0.008) in the One-way ANOVA result for SBS values between all groups, but the protocols showed statistically similar results (p ≥ 0.05-Tukey's tests) concerning the photoactivated faces (V6C, V3M3D and V3C3I) and photoactivation time (V3C and V6C) factors individually. There was no statistically significant difference (p ≥ 0.05) in the One-way ANOVA result for DC values. CONCLUSION: The SBS and DC values will vary depending on the protocol applied. CLINICAL RELEVANCE: It is possible to maintain the bracket fixation quality with the use of a high-power LED photo activator associated with a shorter photoactivation time. However, it is assumed that not all types of protocols that might be applied will provide quality bonding, such as V3C, V3M3D and V3C3I, which may - depending on the SBS and DC values - affect the final treatment time, due to brackets debonding, or increase of possibility of damage to dental enamel during bracket removal. Clinical studies are suggested to confirm the hypotheses of this research.

Batch and Continuous Flow Total Synthesis of Cannabidiol.

Herein, we present a comprehensive total synthesis of cannabidiol integrating both batch and continuous flow conditions. Our approach is planned to streamline the synthesis of olivetolic acid derivatives and utilize an enantiomerically pure monoterpene moiety obtained from naturally occurring (R)-(+)-limonene by photocatalysis. Key reactions, including the synthesis of olivetolic ester and a Friedel-Crafts alkylation, are successfully adapted to continuous flow, resulting in improved yields and selectivities. This study not only offers a scalable and efficient route for cannabidiol synthesis but also contributes to the synthetic approaches to access cannabinoids (diversity synthesis), with potential applications in medicinal and industrial contexts.

Influence of crown-lengthening surgery on teeth rehabilitated with ceramic single crowns: A 12-month prospective clinical study.

OBJECTIVE: To compare the clinical periodontal parameters of teeth restored with a single ceramic crown, with and without crown lengthening procedure. METHODS: This prospective, longitudinal, controlled, and single-blinded clinical trial involved 22 patients with a total of forty-one teeth with ceramic crowns. The teeth were divided into two groups: test (n = 21), comprising teeth rehabilitated post crown-lengthening surgery, and control (n = 20), comprising teeth rehabilitated without crown-lengthening surgery. Plaque index (PI), gingival index (GI), probing depth (PD), bleeding on probing (BoP), and clinical attachment level (CAL) were compared between groups (surgically treated and non-surgically treated) and within each group for each type of site (treated -tt; adjacent - ad; and nonadjacent - nad). Additionally, gingival phenotype (GP), gingival recession (GR), and keratinized tissue width (KTW) were also assessed post- restoration. Statistical analyses used a significance level set at 5 %. RESULTS: PI, GI, and BoP were reduced, but no statistically significant differences were observed within each group or between groups for most follow-up periods. CAL of the TT sites was consistently higher in the test group, and PD was also higher in the test group (p < 0.05), except at T3. adPD, nadPD, adCAL, and nadCAL demonstrated no significant differences between groups and periods. A significant association was identified between GP and the occurrence of GR, with the thick-flat phenotype demonstrating less association with GR, regardless of whether crown lengthening was performed or not. CONCLUSION: Crown-lengthening surgery in rehabilitated teeth does not significantly affect PI and GI after 12 months. Although crown-lengthening surgery affected PD and CAL in TT sites, it did not affect adjacent and non-adjacent sites. CLINICAL RELEVANCE: These findings emphasize the importance of considering individual patient factors and the potential impact on periodontal tissues when planning crown-lengthening surgery. Clinicians must have a comprehensive understanding of the dynamics of the periodontal tissues involved in restorative treatments to optimize the procedure, increase success rates, and minimize potential complications.

Exfoliation of titanium nitride using a non-thermal plasma process.

In this study, we present a novel approach for the exfoliation of titanium nitride (TiN) powders utilizing a rapid, facile, and environmentally friendly non-thermal plasma method. This method involves the use of an electric arc and nitrogen as the ambient gas at room temperature to generate ionized particles. These ionized species interact with the ceramic crystal of TiN, resulting in a pronounced structural expansion. The exfoliated TiN products were comprehensively characterized using transmission electron microscopy, X-ray diffraction, and Raman spectroscopy. Remarkably, the cubic crystal structure of TiN was effectively retained, while the (200) crystal plane d-spacing increased from 2.08 to 3.09 Å, accompanied by a reduction in crystallite size and alterations in Raman vibrational modes. Collectively, these findings provide compelling evidence for the successful exfoliation of TiN structures using our innovative non-thermal plasma method, opening up exciting possibilities for advanced material applications.

Pharmacological potential of 4-dimethylamino chalcone against acute and neuropathic pain in mice.

OBJECTIVES: This work investigated the acute antinociceptive effect of a synthetic chalcone, 4-dimethylamino chalcone (DMAC), as well as its effects on vincristine-induced peripheral neuropathy (VIPN) in mice. METHODS: The inhibitory activity of myeloperoxidase was assessed by measuring HOCl formation. Formalin and hot plate tests were used to study the acute antinociceptive effect of DMAC. VIPN was induced through the administration of vincristine sulphate (0.1 mg/kg, i.p., 14 days). Then, DMSO, DMAC (10 or 30 mg/kg; i.p.), or pregabalin (10 mg/kg, i.p.) were administered for 14 consecutive days. Thermal hyperalgesia and mechanical allodynia were evaluated before and after VIPN induction and on days 1, 3, 7, and 14 of treatment. Neurodegeneration and neuroinflammation were assessed through immunohistochemistry for NF200, iNOS, and arginase-1 within the sciatic nerve. KEY FINDINGS: DMAC inhibited myeloperoxidase activity in vitro and presented an acute antinociceptive effect in both formalin and hot plate tests, with the involvement of muscarinic and opioid receptors. Treatment with 30 mg/kg of DMAC significantly attenuated thermal hyperalgesia and mechanical allodynia and prevented macrophage proinflammatory polarisation in VIPN mice. CONCLUSIONS: Our results show that DMAC, acting through different mechanisms, effectively attenuates VIPN.

Adhesive Cementation of CAD/CAM Silica-based Ceramics: Effect of Adhesive Type and Long-term Aging on the Bond Strength to Composite Cement.

PURPOSE: To investigate the effect of adhesive type and long-term aging on the shear bond strength (SBS) between silica-based ceramics and composite cement (CC). MATERIALS AND METHODS: Lithium-silicate (LS), feldspathic (FD) and polymer-infiltrated ceramic (PIC) blocks were sectioned (10 x 12 x 2 mm) and divided into 24 groups considering the factors: "ceramics" (LS, FD, and PIC), "adhesive" (Ctrl: without adhesive; 2SC: 2-step conventional; 3SC: 3-step conventional; 1SU: 1-step universal), and "aging" (non-aged or aged [A]). After the surface treatments, CC cylinders (n = 15, Ø = 2 mm; height = 2 mm) were made and half of the samples were subjected to thermocycling (10,000) and stored in water at 37°C for 18 months. The samples were submitted to SBS testing (100 kgf, 1 mm/min) and failure analysis. Extra samples were prepared for microscopic analysis of the adhesive interface. SBS (MPa) data was analyzed by 3-way ANOVA and Tukey's test (5%). Weibull analysis was performed on the SBS data. RESULTS: All factors and interactions were significant for SBS (p<0.05). Before aging, there was no significant difference between the tested groups and the respective control groups. After aging, the LS_1SU (22.18 ± 7.74) and LS_2SC (17.32 ± 5.86) groups exhibited significantly lower SBS than did the LS_Ctrl (30.30 ± 6.11). Only the LS_1SU group showed a significant decrease in SBS after aging vs without aging. The LS_1SU (12.20) group showed the highest Weibull modulus, which was significantly higher than LS_2SC_A (2.82) and LS_1SU_A (3.15) groups. CONCLUSION: No type of adhesive applied after silane benefitted the long-term adhesion of silica-based ceramics to CC in comparison to the groups without adhesive.

Accuracy, adaptation and margin quality of monolithic zirconia crowns fabricated by 3D printing versus subtractive manufacturing technique: A systematic review and meta-analysis of in vitro studies.

OBJECTIVE: The purpose of this systematic review and meta-analysis was to evaluate the accuracy (trueness and precision), marginal and internal adaptation, and margin quality of zirconia crowns made by additive manufacturing compared to subtractive manufacturing technology. METHODS: The investigation adhered to the PRISMA-ScR guidelines for systematic reviews and was registered at the Prospero database (n°CRD42023452927). Four electronic databases, including PubMed, Scopus, Embase, and Web of Science and manual search was conducted to find relevant studies published until September 2023. In vitro studies that assessed the trueness and precision, marginal and internal adaptation, and margin quality of printed crowns compared to milled ones were included. Studies on crowns over implants, pontics, temporary restorations, laminates, or exclusively experimental materials were excluded. RESULTS: A total of 9 studies were included in the descriptive reporting and 7 for meta-analysis. The global meta-analysis of the trueness (P<0.74,I2=90 %) and the margin quality (P<0.61,I2=0 %) indicated no significant difference between the root mean square of printed and milled zirconia crowns. The subgroup analysis for the printing system showed a significant effect (P<0.01). The meta-analysis of the crown areas indicated no significant difference in most of the areas, except for the marginal (favoring milled crowns) and axial (favoring printed crowns) areas. For precision and adaptation, both methods showed a clinically acceptable level. CONCLUSIONS: Additive manufacturing technology produces crowns with trueness and margin quality comparable to subtractive manufacturing. Both techniques have demonstrated the ability to produce crowns with precision levels, internal discrepancy, and marginal fit within clinically acceptable limits. CLINICAL SIGNIFICANCE: 3D printing emerges as a promising and potentially applicable alternative method for manufacturing zirconia crowns, as it shows trueness and margin quality comparable to restorations produced by the subtractive method.

Beneficial Effects of Oral Carbon Monoxide on Doxorubicin-Induced Cardiotoxicity.

BACKGROUND: Doxorubicin and other anthracyclines are crucial cancer treatment drugs. However, they are associated with significant cardiotoxicity, severely affecting patient care and limiting dosage and usage. Previous studies have shown that low carbon monoxide (CO) concentrations protect against doxorubicin toxicity. However, traditional methods of CO delivery pose complex challenges for daily administration, such as dosing and toxicity. To address these challenges, we developed a novel oral liquid drug product containing CO (HBI-002) that can be easily self-administered by patients with cancer undergoing doxorubicin treatment, resulting in CO being delivered through the upper gastrointestinal tract. METHODS AND RESULTS: HBI-002 was tested in a murine model of doxorubicin cardiotoxicity in the presence and absence of lung or breast cancer. The mice received HBI-002 twice daily before doxorubicin administration and experienced increased carboxyhemoglobin levels from a baseline of ≈1% to 7%. Heart tissue from mice treated with HBI-002 had a 6.3-fold increase in CO concentrations and higher expression of the cytoprotective enzyme heme oxygenase-1 compared with placebo control. In both acute and chronic doxorubicin toxicity scenarios, HBI-002 protected the heart from cardiotoxic effects, including limiting tissue damage and cardiac dysfunction and improving survival. In addition, HBI-002 did not compromise the efficacy of doxorubicin in reducing tumor volume, but rather enhanced the sensitivity of breast 4T1 cancer cells to doxorubicin while simultaneously protecting cardiac function. CONCLUSIONS: These findings strongly support using HBI-002 as a cardioprotective agent that maintains the therapeutic benefits of doxorubicin cancer treatment while mitigating cardiac damage.

Multiple variation of right renal and gonadal vascularization: report of two cases.

We present two cases of multiple anatomical variations of the renal and gonadal vessels. The first case presented duplication of the renal vein and the presence of an accessory renal artery. However, the most interesting fact, in this case, was that the right gonadal vein emptied into the inferior right renal vein instead of ending in the inferior vena cava as would typically be the case. In the second case, we also found an accessory renal artery and the right gonadal vein emptied at the exact junction between the right renal vein and the inferior vena cava. Clinicians and surgeons should be familiar with anatomical variations to provide an accurate diagnosis during preoperative studies and to avoid surprises in abdominal surgical procedures.

Este estudo apresenta dois casos de variação anatômica múltipla de vasos renais e gonadais. O primeiro caso apresentou uma duplicação da veia renal e a presença de uma artéria renal acessória. Porém, o fato mais interessante nesse caso foi a veia gonadal direita desembocar na veia renal direita inferior em vez de terminar na veia cava inferior, como seria o normal. No segundo caso, além de também encontrarmos uma artéria renal acessória, a veia gonadal direita desembocava no exato ponto de junção entre a veia renal direita e a veia cava inferior. Clínicos e cirurgiões devem estar familiarizados com a presença de possíveis variações dos vasos renais e gonadais, sendo um conhecimento imprescindível para obter um diagnóstico mais preciso e para evitar surpresas em procedimentos cirúrgicos abdominais.

Comparison between use of a pleural drainage system with flutter valve and a conventional water-seal drainage system after lung resection: a randomized prospective study.

BACKGROUND: There is still a debate regarding the most appropriate pleural collector model to ensure a short hospital stay and minimum complications. OBJECTIVES: To study aimed to compare the time of air leak, time to drain removal, and length of hospital stay between a standard water-seal drainage system and a pleural collector system with a unidirectional flutter valve and rigid chamber. DESIGN AND SETTING: A randomized prospective clinical trial was conducted at a high-complexity hospital in São Paulo, Brazil. METHODS: Sixty-three patients who underwent open or video-assisted thoracoscopic lung wedge resection or lobectomy were randomized into two groups, according to the drainage system used: the control group (WS), which used a conventional water-seal pleural collector, and the study group (V), which used a flutter valve device (Sinapi® Model XL1000®). Variables related to the drainage system, time of air leak, time to drain removal, and time spent in hospital were compared between the groups. RESULTS: Most patients (63%) had lung cancer. No differences were observed between the groups in the time of air leak or time spent hospitalized. The time to drain removal was slightly shorter in the V group; however, the difference was not statistically significant. Seven patients presented with surgery-related complications: five and two in the WS and V groups, respectively. CONCLUSIONS: Air leak, time to drain removal, and time spent in the hospital were similar between the groups. The system used in the V group resulted in no adverse events and was safe. REGISTRATION: RBR-85qq6jc (https://ensaiosclinicos.gov.br/rg/RBR-85qq6jc).

Effect of ZrO2 paste, surface treatments, and storage on Weibull characteristics and resin bond strength to zirconia.

The objective is to evaluate the effect of different surface treatments and storage on the shear strength of ultratranslucent zirconia. 36 blocks of ultra-translucent zirconia were fabricated (7x7x2mm) and sintered. Then, divided into 12 groups according to the "surface treatment" (C -Primer; Al -Sandblasting with Al2O3 + Primer; Si -Silicate + Primer; Gl -Glaze + HF + Primer; Z -Zirlink; Zp -Zirlink + Primer) and "storage" factors (ST-with 150 days/37º and without). After surface treatment, five cylinders (Ø=2mm; h=2.0mm) of resin cement (n=15) were constructed in each ceramic block; at the end, the shear strength test was performed (1mm/min, 50Kgf), and analysis of surface failures. 60 additional samples (2x2x2mm) were made for extras analysis (surface roughness, MEV, and EDS). Bond strength and surface roughness data were statistically evaluated by ANOVA (2 factors/1 factor), Tukey test (5%), and Weibull analysis, respectively. ANOVA (2-way) revealed that all factors were statistically significant for bond strength. The silicatization groups (SiST: 30.47AMPa; Si: 29.21AMPa) showed the highest bond strength values, regardless of storage (Tukey's test). While the groups treated with Zirlink (ZST: 2.76FMPa; Z: 5.27EFMPa) showed the lowest values, just similar to the GlST group (5.14EFMPa). The Weibull modulus (m) showed a statistical difference between groups (p=0.000). ANOVA (1 factor) revealed that the "surface treatment" factor (p=0.0000) was statistically significant for surface roughness. Therefore, the application of Zirlink and Glaze on pre-sintered zirconia did not promote efficient adhesion of the ultratranslucent zirconia to the resin cement, even when associated with a primer containing MDP.

The Fbn1 gene variant governs passive ascending aortic mechanics in the mgΔlpn mouse model of Marfan syndrome when superimposed to perlecan haploinsufficiency.

Introduction: Ascending thoracic aortic aneurysms arise from pathological tissue remodeling that leads to abnormal wall dilation and increases the risk of fatal dissection/rupture. Large variability in disease manifestations across family members who carry a causative genetic variant for thoracic aortic aneurysms suggests that genetic modifiers may exacerbate clinical outcomes. Decreased perlecan expression in the aorta of mgΔlpn mice with severe Marfan syndrome phenotype advocates for exploring perlecan-encoding Hspg2 as a candidate modifier gene. Methods: To determine the effect of concurrent Hspg2 and Fbn1 mutations on the progression of thoracic aortopathy, we characterized the microstructure and passive mechanical response of the ascending thoracic aorta in female mice of four genetic backgrounds: wild-type, heterozygous with a mutation in the Fbn1 gene (mgΔlpn), heterozygous with a mutation in the Hspg2 gene (Hspg2+/-), and double mutants carrying both the Fbn1 and Hspg2 variants (dMut). Results: Elastic fiber fragmentation and medial disarray progress from the internal elastic lamina outward as the ascending thoracic aorta dilates in mgΔlpn and dMut mice. Concurrent increase in total collagen content relative to elastin reduces energy storage capacity and cyclic distensibility of aortic tissues from mice that carry the Fbn1 variant. Inherent circumferential tissue stiffening strongly correlates with the severity of aortic dilatation in mgΔlpn and dMut mice. Perlecan haploinsufficiency superimposed to the mgΔlpn mutation curbs the viability of dMut mice, increases the occurrence of aortic enlargement, and reduces the axial stretch in aortic tissues. Discussion: Overall, our findings show that dMut mice are more vulnerable than mgΔlpn mice without an Hspg2 mutation, yet later endpoints and additional structural and functional readouts are needed to identify causative mechanisms.

Catalase and Uric Acid Prevent Morphological Damage to the Sperm Flagella of Colossoma macropomum During 96 Hours at Low Storage Temperatures.

Oxidative stress is one of the main causes of loss of sperm function during chilled storage. The aim of the current study was to evaluate the effects of a fructose-based extender, which was supplemented with catalase or uric acid, on the motility, viability, morphological integrity, and lipid peroxidation (LPO) of Colossoma macropomum spermatozoa. Sperm was diluted in extenders containing catalase (0; 0.1; 0.8; and 1.5 kU/L) or uric acid (0; 0.25; 0.5; and 1.0 mmol/L) and then stored at 4.3 ± 0.6°C for 96 hours. The chilling storage time had more significant and pronounced effects on practically all the measured sperm quality parameters than the different concentrations of both antioxidants added to the extenders. This was true for sperm motility, motility duration, sperm viability, and the percentage of normal spermatozoa. In fact, for all these parameters, values were higher in the extenders supplemented with catalase or uric acid, than those not supplemented with these antioxidants, especially after 96 hours. The LPO process showed an antioxidant-dependent response. In catalase-supplemented extenders thiobarbituric acid reactive substance (TBARS) levels increased gradually and significantly with time, but remained stable during the 96 hours of chilled storage in all samples in which uric acid was added. Despite this, TBARS levels were lower in the extenders supplemented with both catalase and uric acid than in those not having these antioxidants. Inverse correlations were found between sperm motility and the damage in sperm flagella. Our findings suggest that the supplementation of an extender with catalase or uric acid is beneficial and protects fish sperm membranes from damage caused by oxidative stress during low-temperature storage. The extenders containing 0.1 kU/L of catalase and 0.25 mmol/L of uric acid provided effective antioxidant protection for the spermatozoa of this important Amazonian fish.

Computational methodology to support functional vision assessment in premature infants: A viability study.

BACKGROUND: Premature newborns have a higher risk of abnormal visual development and visual impairment. OBJECTIVE: To develop a computational methodology to help assess functional vision in premature infants by tracking iris distances. METHODS: This experimental study was carried out with children up to two years old. A pattern of image capture with the visual stimulus was proposed to evaluate visual functions of vertical and horizontal visual tracking, visual field, vestibulo-ocular reflex, and fixation. The participants' visual responses were filmed to compose a dataset and develop a detection algorithm using the OpenCV library allied with FaceMesh for the detection and selection of the face, detection of specific facial points and tracking of the iris positions is done. A feasibility study was also conducted from the videos processed by the software. RESULTS: Forty-one children of different ages and diagnoses participated in the experimental study, forming a robust dataset. The software resulted in the tracking of iris positions during visual function evaluation stimuli. Furthermore, in the feasibility study, 8 children participated, divided into Pre-term and Term groups. There was no statistical difference in any visual variable analyzed in the comparison between groups. CONCLUSION: The computational methodology developed was able to track the distances traveled by the iris, and thus can be used to help assess visual function in children.

Are pvcrt-o and pvmdr1 Gene Mutations Associated with Plasmodium vivax Chloroquine-Resistant Parasites?

(1) Background: Malaria remains a significant global public health issue. Since parasites quickly became resistant to most of the available antimalarial drugs, treatment effectiveness must be constantly monitored. In Brazil, up to 10% of cases of vivax malaria resistant to chloroquine (CQ) have been registered. Unlike P. falciparum, there are no definitive molecular markers for the chemoresistance of P. vivax to CQ. This work aimed to investigate whether polymorphisms in the pvcrt-o and pvmdr1 genes could be used as markers for assessing its resistance to CQ. (2) Methods: A total of 130 samples from P. vivax malaria cases with no clinical and/or parasitological evidence of CQ resistance were studied through polymerase chain reaction for gene amplification followed by target DNA sequencing. (3) Results: In the pvcrt-o exons, the K10 insert was present in 14% of the isolates. Regarding pvmdr1, T958M and F1076L haplotypes showed frequencies of 95% and 3%, respectively, while the SNP Y976F was not detected. (4) Conclusions: Since K10-pvcrt-o and F1076L/T958M-pvmdr1 polymorphisms were detected in samples from patients who responded well to CQ treatment, it can be concluded that mutations in these genes do not seem to have a potential for association with the phenotype of CQ resistance.

Adolescent pregnancy in Cruzeiro do Sul, Acre, Brazil: socioeconomic characteristics, prenatal and obstetric care. / Parturientes adolescentes em Cruzeiro do Sul, Acre, Brasil: características socioeconômicas e obstétricas.

The present study aimed to investigate the socioeconomic and obstetric characteristics of adolescent mothers and the complications they cause to maternal and neonatal health. This baseline data analysis of the MINA-Brazil birth cohort was conducted in the municipality of Cruzeiro do Sul, state of Acre, Brazil. The chi-square test was used to compare characteristics of adolescent and adult postpartum women, and multiple Poisson regression models with robust variance were used to assess associated factors. Among the postpartum women, 26.2% (95%CI: 24.0-28.4) were adolescents. Factors associated with childbirth in adolescence included: nine years or less of schooling (adjPR:1.36; 95%CI: 1.14-1.61), belongs to the lowest quartiles of the wealth index (1st quartile: adjPR:1.40; 95%CI: 1.08-1.80) (2nd quartile: adjPR:1.37; 95%CI: 1.08-1.74), primigravidae (adjPR:3.69; 95%CI: 2.98-4.57), low pre-pregnancy BMI (adjPR:1.28; CI95%: 1.04-1.57), urinary tract infection during pregnancy (adjPR:1.25; CI95%: 1.07-1.46) and less than six prenatal consultations (adjPR:1.42; 95%CI: 1.21-1.66). Poverty, little schooling, primigravidae, low pre-pregnancy BMI, urinary tract infection during pregnancy and few prenatal consultations were associated with childbirth during adolescence in a municipality in the Northern region of Brazil.

O objetivo do estudo foi investigar as características socioeconômicas e obstétricas de parturientes adolescentes e suas complicações sobre a saúde materna e neonatal. Trata-se de uma análise de dados da linha de base da coorte de nascimentos MINA-Brasil conduzida no município de Cruzeiro do Sul, estado do Acre. Utilizou-se teste qui-quadrado para comparar características das puérperas adolescentes com as adultas e modelos múltiplos de regressão de Poisson com variância robusta para avaliar fatores associados. Entre as puérperas estudadas, 26,2% (IC95%: 24,0-28,4) eram adolescentes. Os fatores associados ao parto na adolescência foram ter nove anos ou menos de estudo (RPaj:1,36; IC95%: 1,14-1,61), pertencer aos menores quartis do índice de riqueza (1° quartil: RPaj:1,40; IC95%: 1,08-1,80) (2° quartil: RPaj:1,37; IC95%: 1,08-1,74), ser primigesta (RPaj:3,69; IC95%: 2,98-4,57), baixo IMC pré-gestacional (RPaj:1,28; IC95%: 1,04-1,57), infecção urinária na gravidez (RPaj:1,25; IC95%: 1,07-1,46) e menos de seis consultas de pré-natal (RPaj:1,42; IC95%: 1,21-1,66). Pobreza, baixa escolaridade, primigestação, baixo IMC pré-gestacional, infecção urinária na gestação e menor número de consultas de pré-natal foram associados ao parto na adolescência em município da região Norte do Brasil.