AlGaAs soliton microcombs at room temperature.

Soliton mode locking in high-Q microcavities provides a way to integrate frequency comb systems. Among material platforms, AlGaAs has one of the largest optical nonlinearity coefficients, and is advantageous for low-pump-threshold comb generation. However, AlGaAs also has a very large thermo-optic effect that destabilizes soliton formation, and femtosecond soliton pulse generation has only been possible at cryogenic temperatures. Here, soliton generation in AlGaAs microresonators at room temperature is reported for the first time, to the best of our knowledge. The destabilizing thermo-optic effect is shown to instead provide stability in the high-repetition-rate soliton regime (corresponding to a large, normalized second-order dispersion parameter D2/κ). Single soliton and soliton crystal generation with sub-milliwatt optical pump power are demonstrated. The generality of this approach is verified in a high-Q silica microtoroid where manual tuning into the soliton regime is demonstrated. Besides the advantages of large optical nonlinearity, these AlGaAs devices are natural candidates for integration with semiconductor pump lasers. Furthermore, the approach should generalize to any high-Q resonator material platform.

Architecture for microcomb-based GHz-mid-infrared dual-comb spectroscopy.

Dual-comb spectroscopy (DCS) offers high sensitivity and wide spectral coverage without the need for bulky spectrometers or mechanical moving parts. And DCS in the mid-infrared (mid-IR) is of keen interest because of inherently strong molecular spectroscopic signatures in these bands. We report GHz-resolution mid-IR DCS of methane and ethane that is derived from counter-propagating (CP) soliton microcombs in combination with interleaved difference frequency generation. Because all four combs required to generate the two mid-IR combs rely upon stability derived from a single high-Q microcavity, the system architecture is both simplified and does not require external frequency locking. Methane and ethane spectra are measured over intervals as short as 0.5 ms, a time scale that can be further reduced using a different CP soliton arrangement. Also, tuning of spectral resolution on demand is demonstrated. Although at an early phase of development, the results are a step towards mid-IR gas sensors with chip-based architectures for chemical threat detection, breath analysis, combustion studies, and outdoor observation of trace gases.

Petermann-factor sensitivity limit near an exceptional point in a Brillouin ring laser gyroscope.

Exceptional points are singularities of open systems, and among their many remarkable properties, they provide a way to enhance the responsivity of sensors. Here we show that the improved responsivity of a laser gyroscope caused by operation near an exceptional point is precisely compensated by increasing laser noise. The noise, of fundamental origin, is enhanced because the laser mode spectrum loses the oft-assumed property of orthogonality. This occurs as system eigenvectors coalesce near the exceptional point and a bi-orthogonal analysis confirms experimental observations. While the results do not preclude other possible advantages of the exceptional-point-enhanced responsivity, they do show that the fundamental sensitivity limit of the gyroscope is not improved through this form of operation. Besides being important to the physics of microcavities and non-Hermitian photonics, these results help clarify fundamental sensitivity limits in a specific class of exceptional-point sensor.

Direct Kerr frequency comb atomic spectroscopy and stabilization.

Microresonator-based soliton frequency combs, microcombs, have recently emerged to offer low-noise, photonic-chip sources for applications, spanning from timekeeping to optical-frequency synthesis and ranging. Broad optical bandwidth, brightness, coherence, and frequency stability have made frequency combs important to directly probe atoms and molecules, especially in trace gas detection, multiphoton light-atom interactions, and spectroscopy in the extreme ultraviolet. Here, we explore direct microcomb atomic spectroscopy, using a cascaded, two-photon 1529-nm atomic transition in a rubidium micromachined cell. Fine and simultaneous repetition rate and carrier-envelope offset frequency control of the soliton enables direct sub-Doppler and hyperfine spectroscopy. Moreover, the entire set of microcomb modes are stabilized to this atomic transition, yielding absolute optical-frequency fluctuations at the kilohertz level over a few seconds and <1-MHz day-to-day accuracy. Our work demonstrates direct atomic spectroscopy with Kerr microcombs and provides an atomic-stabilized microcomb laser source, operating across the telecom band for sensing, dimensional metrology, and communication.

Observation of the exceptional-point-enhanced Sagnac effect.

Exceptional points (EPs) are special spectral degeneracies of non-Hermitian Hamiltonians that govern the dynamics of open systems. At an EP, two or more eigenvalues, and the corresponding eigenstates, coalesce1-3. Recently, it was predicted that operation of an optical gyroscope near an EP results in improved response to rotations4,5. However, the performance of such a system has not been examined experimentally. Here we introduce a precisely controllable physical system for the study of non-Hermitian physics and nonlinear optics in high-quality-factor microresonators. Because this system dissipatively couples counter-propagating lightwaves within the resonator, it also functions as a sensitive gyroscope for the measurement of rotations. We use our system to investigate the predicted EP-enhanced Sagnac effect4,5 and observe a four-fold increase in the Sagnac scale factor by directly measuring rotations applied to the resonator. The level of enhancement can be controlled by adjusting the system bias relative to the EP, and modelling results confirm the observed enhancement. Moreover, we characterize the sensitivity of the gyroscope near the EP. Besides verifying EP physics, this work is important for the understanding of optical gyroscopes.

Directly pumped 10 GHz microcomb modules from low-power diode lasers.

Soliton microcombs offer the prospect of advanced optical metrology and timing systems in compact form factors. In these applications, the pumping of microcombs directly from a semiconductor laser without amplification or triggering components is desirable to reduce system power and to simplify system design. At the same time, low-repetition-rate microcombs are required in many comb applications as an interface to detectors and electronics, but their increased mode volume makes them challenging to pump at low power. Here 10 GHz repetition rate soliton microcombs are directly pumped by low-power (<20 mW) diode lasers. High-Q silica microresonators are used for this low-power operation and are packaged into fiber-connectorized modules that feature temperature control for improved long-term frequency stability.

Searching for Exoplanets Using a Microresonator Astrocomb.

Orbiting planets induce a weak radial velocity (RV) shift in the host star that provides a powerful method of planet detection. Importantly, the RV technique provides information about the exoplanet mass, which is unavailable with the complementary technique of transit photometry. However, RV detection of an Earth-like planet in the 'habitable zone'1 requires extreme spectroscopic precision that is only possible using a laser frequency comb (LFC)2. Conventional LFCs require complex filtering steps to be compatible with astronomical spectrographs, but a new chip-based microresonator device, the Kerr soliton microcomb3-8, is an ideal match for astronomical spectrograph resolution and can eliminate these filtering steps. Here, we demonstrate an atomic/molecular line-referenced soliton microcomb as a first in-the-field demonstration of microcombs for calibration of astronomical spectrographs. These devices can ultimately provide LFC systems that would occupy only a few cubic centimetres9,10, thereby greatly expanding implementation of these technologies into remote and mobile environments beyond the research lab.

An optical-frequency synthesizer using integrated photonics.

Optical-frequency synthesizers, which generate frequency-stable light from a single microwave-frequency reference, are revolutionizing ultrafast science and metrology, but their size, power requirement and cost need to be reduced if they are to be more widely used. Integrated-photonics microchips can be used in high-coherence applications, such as data transmission 1 , highly optimized physical sensors 2 and harnessing quantum states 3 , to lower cost and increase efficiency and portability. Here we describe a method for synthesizing the absolute frequency of a lightwave signal, using integrated photonics to create a phase-coherent microwave-to-optical link. We use a heterogeneously integrated III-V/silicon tunable laser, which is guided by nonlinear frequency combs fabricated on separate silicon chips and pumped by off-chip lasers. The laser frequency output of our optical-frequency synthesizer can be programmed by a microwave clock across 4 terahertz near 1,550 nanometres (the telecommunications C-band) with 1 hertz resolution. Our measurements verify that the output of the synthesizer is exceptionally stable across this region (synthesis error of 7.7 × 10-15 or below). Any application of an optical-frequency source could benefit from the high-precision optical synthesis presented here. Leveraging high-volume semiconductor processing built around advanced materials could allow such low-cost, low-power and compact integrated-photonics devices to be widely used.

Soliton microcomb range measurement.

Laser-based range measurement systems are important in many application areas, including autonomous vehicles, robotics, manufacturing, formation flying of satellites, and basic science. Coherent laser ranging systems using dual-frequency combs provide an unprecedented combination of long range, high precision, and fast update rate. We report dual-comb distance measurement using chip-based soliton microcombs. A single pump laser was used to generate dual-frequency combs within a single microresonator as counterpropagating solitons. We demonstrated time-of-flight measurement with 200-nanometer precision at an averaging time of 500 milliseconds within a range ambiguity of 16 millimeters. Measurements at distances up to 25 meters with much lower precision were also performed. Our chip-based source is an important step toward miniature dual-comb laser ranging systems that are suitable for photonic integration.

Phonon-Limited-Linewidth of Brillouin Lasers at Cryogenic Temperatures.

Laser linewidth is of central importance in spectroscopy, frequency metrology, and all applications of lasers requiring high coherence. It is also of fundamental importance, because the Schawlow-Townes laser linewidth limit is of quantum origin. Recently, a theory of stimulated Brillouin laser (SBL) linewidth has been reported. While the SBL linewidth formula exhibits power and optical Q factor dependences that are identical to the Schawlow-Townes formula, a source of noise not present in conventional lasers, phonon occupancy of the Brillouin mechanical mode is predicted to be the dominant SBL linewidth contribution. Moreover, the quantum limit of the SBL linewidth is predicted to be twice the Schawlow-Townes limit on account of phonon participation. To help confirm this theory the SBL fundamental linewidth is measured at cryogenic temperatures in a silica microresonator. Its temperature dependence and the SBL linewidth theory are combined to predict the number of thermomechanical quanta at three temperatures. The result agrees with the Bose-Einstein phonon occupancy of the microwave-rate Brillouin mode in support of the SBL linewidth theory prediction.

Fiber taper characterization by optical backscattering reflectometry.

Fiber tapers provide a way to rapidly measure the spectra of many types of optical microcavities. Proper fabrication of the taper ensures that its width varies sufficiently slowly (adiabatically) along the length of the taper so as to maintain single spatial mode propagation. This is usually accomplished by monitoring the spectral transmission through the taper. In addition to this characterization method it is also helpful to know the taper width versus length. By developing a model of optical backscattering within the fiber taper, it is possible to use backscatter measurements to characterize the taper width versus length. The model uses the concept of a local taper numerical aperture to accurately account for varying backscatter collection along the length of the taper. In addition to taper profile information, the backscatter reflectometry method delineates locations along the taper where fluctuations in fiber core refractive index, cladding refractive index, and taper surface roughness each provide the dominant source of backscattering. Rayleigh backscattering coefficients are also extracted by fitting the data with the model and are consistent with the fiber manufacturer's datasheet. The optical backscattering reflectometer is also used to observe defects resulting from microcracks and surface contamination. All of this information can be obtained before the taper is removed from its fabrication apparatus. The backscattering method should also be prove useful for characterization of nanofibers.

Microresonator soliton dual-comb spectroscopy.

Measurement of optical and vibrational spectra with high resolution provides a way to identify chemical species in cluttered environments and is of general importance in many fields. Dual-comb spectroscopy has emerged as a powerful approach for acquiring nearly instantaneous Raman and optical spectra with unprecedented resolution. Spectra are generated directly in the electrical domain, without the need for bulky mechanical spectrometers. We demonstrate a miniature soliton-based dual-comb system that can potentially transfer the approach to a chip platform. These devices achieve high-coherence pulsed mode locking. They also feature broad, reproducible spectral envelopes, an essential feature for dual-comb spectroscopy. Our work shows the potential for integrated spectroscopy with high signal-to-noise ratios and fast acquisition rates.

Spiral resonators for on-chip laser frequency stabilization.

Frequency references are indispensable to radio, microwave and time keeping systems, with far reaching applications in navigation, communication, remote sensing and basic science. Over the past decade, there has been an optical revolution in time keeping and microwave generation that promises to ultimately impact all of these areas. Indeed, the most precise clocks and lowest noise microwave signals are now based on a laser with short-term stability derived from a reference cavity. In spite of the tremendous progress, these systems remain essentially laboratory devices and there is interest in their miniaturization, even towards on-chip systems. Here we describe a chip-based optical reference cavity that uses spatial averaging of thermorefractive noise to enhance resonator stability. Stabilized fibre lasers exhibit relative Allan deviation of 3.9 × 10⁻¹³ at 400 µs averaging time and an effective linewidth <100 Hz by achieving over 26 dB of phase-noise reduction.