Reinforcement learning based variable damping control of wearable robotic limbs for maintaining astronaut pose during extravehicular activity.

As astronauts perform on-orbit servicing of extravehicular activity (EVA) without the help of the space station's robotic arms, it will be rather difficult and labor-consuming to maintain the appropriate position in case of impact. In order to solve this problem, we propose the development of a wearable robotic limb system for astronaut assistance and a variable damping control method for maintaining the astronaut's position. The requirements of the astronaut's impact-resisting ability during EVA were analyzed, including the capabilities of deviation resistance, fast return, oscillation resistance, and accurate return. To meet these needs, the system of the astronaut with robotic limbs was modeled and simplified. In combination with this simplified model and a reinforcement learning algorithm, a variable damping controller for the end of the robotic limb was obtained, which can regulate the dynamic performance of the robot end to resist oscillation after impact. A weightless simulation environment for the astronaut with robotic limbs was constructed. The simulation results demonstrate that the proposed method can meet the recommended requirements for maintaining an astronaut's position during EVA. No matter how the damping coefficient was set, the fixed damping control method failed to meet all four requirements at the same time. In comparison to the fixed damping control method, the variable damping controller proposed in this paper fully satisfied all the impact-resisting requirements by itself. It could prevent excessive deviation from the original position and was able to achieve a fast return to the starting point. The maximum deviation displacement was reduced by 39.3% and the recovery time was cut by 17.7%. Besides, it also had the ability to prevent reciprocating oscillation and return to the original position accurately.

Design and Control of a Series-Parallel Elastic Actuator for a Weight-Bearing Exoskeleton Robot.

Weight-bearing exoskeletons are robots that need to carry loads and interact with humans frequently. Therefore, the actuators of these exoskeletons are supposed to be capable of outputting sufficient force with high compliance and little weight. A series-parallel elastic actuator (SPEA) is designed, in this work, to meet the demanding requirements of an exoskeleton robot called PALExo. A gas spring is installed in parallel with an electric cylinder to adjust the force output range of the actuator according to the needs of the exoskeleton. A series elastic module (SEM) is installed in series with the electric cylinder and gas spring to improve the compliance of the actuator, the stiffness of which is variable to adapt to the different stiffness requirements of the exoskeleton's legs in the standing phase and swinging phase. A force controller combining dynamic compensation and a cascade control with an inner velocity loop and a disturbance observer is designed for the SPEA. The performance of the force controller is verified by experiments and the results demonstrate that the controller has good adaptability to the stiffness of the SEM.

A Bioinspired Soft Swallowing Gripper for Universal Adaptable Grasping.

This article presents the design, fabrication, modeling, and preliminary tests of a bloodworm-inspired soft gripper for universal grasping. The gripper was designed and fabricated based on a toy called water snake wiggly (WSW). The toroidal WSW can evert itself inside-out or outside-in, just like a bloodworm everting its teeth outside to hunt and inside to feed. By driving a WSW rolling itself outside-in to wrap around the items, a bloodworm-inspired gripper was achieved with a flexible and passive form-fitting grasp. To enhance the capability of the gripper, two alternative detachable modules were added to the gripper-a vacuum suction cup for handling objects with smooth nonporous surfaces and an end-needle for taking in and expelling noncorrosive liquids like a syringe. We analyzed the working principles of the gripper and derived the relationship between the gripper's holding force and the objects' scale. Preliminary experiments with a motor-driven gripper prototype were conducted to verify its performance. The experimental results conform well with our theoretical analysis and also indicate the gripper's good universal grasping capacity and reliability in handling a wide range of objects with different surface shapes, geometric dimensions, and stiffness. In addition, the gripper has the unique abilities to pick more than one object during a maneuver, grasp multiple objects in a row without releasing the former ones, and even grasp powdered objects. These have presented a challenge for the existing robotic grippers.

Modular Robotic Limbs for Astronaut Activities Assistance.

In order to meet the assist requirements of extravehicular activity (EVA) for astronauts, such as moving outside the international space station (ISS) or performing on-orbit tasks by a single astronaut, this paper proposes an astronaut robotic limbs system (AstroLimbs) for extravehicular activities assistance. This system has two robotic limbs that can be fixed on the backpack of the astronaut. Each limb is composed of several basic module units with identical structure and function, which makes it modularized and reconfigurable. The robotic limbs can work as extra arms of the astronaut to assist them outside the space station cabin. In this paper, the robotic limbs are designed and developed. The reinforcement learning method is introduced to achieve autonomous motion planning capacity for the robot, which makes the robot intelligent enough to assist the astronaut in unstructured environment. In the meantime, the movement of the robot is also planned to make it move smoothly. The structure scene of the ISS for extravehicular activities is modeled in a simulation environment, which verified the effectiveness of the proposed method.

Passive knee exoskeletons in functional tasks: Biomechanical effects of a SpringExo coil-spring on squats.

Passive wearable exoskeletons are desirable as they can provide assistance during user movements while still maintaining a simple and low-profile design. These can be useful in industrial tasks where an ergonomic device could aid in load lifting without inconveniencing them and reducing fatigue and stress in the lower limbs. The SpringExo is a coil-spring design that aids in knee extension. In this paper, we describe the muscle activation of the knee flexors and extensors from seven healthy participants during repeated squats. The outcome measures are the timings of the key events during squat, flexion angle, muscle activation of rectus femoris and bicep femoris, and foot pressure characteristics of the participants. These outcome measures assess the possible effects of the device during lifting operations where reduced effort in the muscles is desired during ascent phase of the squat, without changing the knee and foot kinematics. The results show that the SpringExo significantly decreased rectus femoris activation during ascent (-2%) without significantly affecting either the bicep femoris or rectus femoris muscle activations in descent. This implies that the user could perform a descent without added effort and ascent with reduced effort. The exoskeleton showed other effects on the biomechanics of the user, increasing average squat time (+0.02 s) and maximum squat time (+0.1 s), and decreasing average knee flexion angle (-4°). The exoskeleton has no effect on foot loading or placement, that is, the user did not have to revise their stance while using the device.