Analysis of Non-Destructive Indicating Properties for Predicting Compressive Strengths of Dendrocalamus sericeus Munro Bamboo Culms.

Bamboo is a natural material with the potential for being used in sustainable construction. However, uncertainty in the bearing capacity of the bamboo results in nonstandard values for structural engineering design. This research studied the simple and multiple linear regression analyses for indicating properties to predict the axial compressive load capacity and strength of bamboo culms, which will be useful information for quality control during building construction and further structural grading. First, twelve basic physical properties were measured from 111 samples of Dendrocalamus sericeus Munro bamboo culms, and axial compressive load tests of the bamboo culms were performed. Then, the correlation significance of the physical properties to axial load capacity and strength (load per area) were analyzed by the Pearson correlation method. The results show that five parameters, i.e., linear mass, culm wall thickness, external diameter, moisture content, and density, were statistically significant with the responses (compressive load capacity and compressive strength) and then defined as "candidates for indicating properties". Next, simple linear and multiple linear regression were analyzed to formulate the relationship between the significant indicating properties and the responses. From the simple linear regression analysis, linear mass can be best used as an indicating property for predicting the maximum compressive load. The maximum compressive strength was well associated with density. The multiple linear regression analysis shows an improvement in the response predictions with respect to the simple linear regression analysis with the higher R2-values. Finally, structural grading of the bamboo is determined.

Variation of Anthocyanin, Phenol, and Antioxidant Capacity in Straw among Rice Varieties and Growing Locations as a Potential Source of Natural Bioactive Compounds.

This study evaluated the variation in bioactive compounds (anthocyanins, phenols, and antioxidants) among 22 rice varieties in the same growing locations and among four varieties collected from eight different provinces in Northern Thailand. Wide variation in anthocyanins, phenols, and antioxidant capacity was established, ranging from 1.6 to 33.0 mg/100 g, 249.9 to 477.7 mg gallic acid/100 g, and 0 to 3,288.5 mg trolox equivalent/100 g, respectively. The highest straw anthocyanin and phenol concentrations were found in KDK (a traditional photoperiod-sensitive variety with purple pericarp and leaves) and K4 (an advanced, photoperiod-insensitive variety with purple pericarp and leaves), while the highest antioxidant capacity was found in KH CMU (an improved traditional photoperiod sensitive variety with a purple pericarp and green leaves) and K4. The variation of the bioactive compounds was also found in the same variety grown at different locations, e.g., the KDMl105 grown in Prayao province had a straw anthocyanin concentration higher than when grown in Mae Hong Son province. The effect was also observed in phenol content and antioxidant capacity when the same rice variety was grown across various locations. A significant correlation between total phenol and antioxidant capacity was observed across rice varieties and growing locations but was not found between anthocyanin and antioxidant capacity. This study found that the bioactive compounds in rice straw varied among rice varieties and growing locations. Straw phenol acts as a major antioxidant that can be used as a characteristic for the selection of rice varieties with high antioxidant capacity for use at the industrial scale for the processing of food, pharmaceuticals, and medicinal products.

Properties and Microstructures of Crushed Rock Based-Alkaline Activated Material for Roadway Applications.

The worldwide demand for roads to serve global economic growth has led to the increasing popularity of road improvement using cement. This, in turn, has led to increased demand for cement and the associated problem of CO2 emissions. Alkaline-activated materials (AAMs) could be an alternative binder for relatively low strength construction and rehabilitation as a cement replacement material. Compared to other applications, the lower strength requirements of road construction materials could ease any difficulties with AAM production. In this study, crushed rock (CR) was used as a prime raw material. The mechanisms and microstructures of the hardened AAM were investigated along with its mechanical properties. The results showed that CR-based AAM with an optimum mixture of 5 M of NaOH concentration, an SS/SH ratio of 1.00, and a liquid alkaline-to-binder (L/B) ratio of 0.5 could be used for roadway applications. At this ratio, the paste samples cured at room temperature (26 ± 3 °C) had an early compressive strength (3 days-age) of 3.82 MPa, while the paste samples cured at 60 °C had an early compressive strength of 6.45 MPa. The targeted strength results were able to be applied to a cement-treated base (CTB) for pavement and roadway applications (2.1 to 5.5 MPa).

Influence of Asphalt Emulsion Inclusion on Fly Ash/Hydrated Lime Alkali-Activated Material.

Supplementary cementitious materials have been widely used to reduce the greenhouse gas emissions caused by ordinary Portland cement (OPC), including in the construction of road bases. In addition, the use of OPC in road base stabilization is inefficient due to its moisture sensitivity and lack of flexibility. Therefore, this study investigates the effect of hybrid alkali-activated materials (H-AAM) on flexibility and water prevention when used as binders while proposing a new and sustainable material. A cationic asphalt emulsion (CAE) was applied to increase this cementless material's resistance to moisture damage and flexibility. The physical properties and structural formation of this H-AAM, consisting of fly ash, hydrated lime, and sodium hydroxide, were examined. The results revealed that the addition of CAE decreased the material's mechanical strength due to its hindrance of pozzolanic reactions and alkali activations. This study revealed decreases in the cementitious product's peak in the x-ray diffraction analysis (XRD) tests and the number of tetrahedrons detected in the Fourier transform infrared spectroscopy analysis (FTIR) tests. The scanning electron microscope (SEM) images showed some signs of asphalt films surrounding hybrid alkali-activated particles and even some unreacted FA particles, indicating incomplete chemical reactions in the study material's matrix. However, the H-AAM was still able to meet the minimum road base strength requirement of 1.72 MPa. Furthermore, the toughness and flexibility of the H-AAM were enhanced by CAE. Notably, adding 10% and 20% CAE by weight to the hybrid alkali-activated binder produced a significant advantage in terms of water absorption, which can be explained by its influence on the material's consolidation of its matrices, resulting in significant void reductions. Hence, the outcomes of this study might reveal an opportunity for developing a new stabilizing agent for road bases with water-prevention properties and flexibility that remains faithful to the green construction material concept.

Characteristics of Waste Iron Powder as a Fine Filler in a High-Calcium Fly Ash Geopolymer.

Geopolymer (GP) has been applied as an environmentally-friendly construction material in recent years. Many pozzolanic wastes, such as fly ash (FA) and bottom ash, are commonly used as source materials for synthesizing geopolymer. Nonetheless, many non-pozzolanic wastes are often applied in the field of civil engineering, including waste iron powder (WIP). WIPs are massively produced as by-products from iron and steel industries, and the production rate increases every year. As an iron-based material, WIP has properties of heat induction and restoration, which can enhance the heat curing process of GP. Therefore, this study aimed to utilize WIP in high-calcium FA geopolymer to develop a new type of geopolymer and examine its properties compared to the conventional geopolymer. Scanning electron microscopy and X-ray diffraction were performed on the geopolymers. Mechanical properties, including compressive strength and flexural strength, were also determined. In addition, setting time and temperature monitoring during the heat curing process were carried out. The results indicated that the addition of WIP in FA geopolymer decreased the compressive strength, owing to the formation of tetrahydroxoferrate (II) sodium or Na2[Fe(OH)4]. However, a significant increase in the flexural strength of GP with WIP addition was detected. A flexural strength of 8.5 MPa was achieved by a 28-day sample with 20% of WIP addition, nearly three times higher than that of control.

Influence of Cement Replacement with Fly Ash and Ground Sand with Different Fineness on Alkali-Silica Reaction of Mortar.

The alkali-silica reaction (ASR) is an important consideration in ensuring the long-term durability of concrete materials, especially for those containing reactive aggregates. Although fly ash (FA) has proven to be useful in preventing ASR expansion, the filler effect and the effect of FA fineness on ASR expansion are not well defined in the present literature. Hence, this study aimed to examine the effects of the filler and fineness of FA on ASR mortar expansion. FAs with two different finenesses were used to substitute ordinary Portland cement (OPC) at 20% by weight of binder. River sand (RS) with the same fineness as the FA was also used to replace OPC at the same rate as FA. The replacement of OPC with RS (an inert material) was carried out to observe the filler effect of FA on ASR. The results showed that FA and RS provided lower ASR expansions compared with the control mortar. Fine and coarse fly ashes in this study had almost the same effectiveness in mitigating the ASR expansion of the mortars. For the filler effect, smaller particles of RS had more influence on the ASR reduction than RS with coarser particles. A significant mitigation of the ASR expansion was obtained by decreasing the OPC content in the mortar mixture through its partial substitution with FA and RS.