Quantifying rider posture variability in powered two- and three-wheelers for safety assessment.

OBJECTIVE: Injury outcomes for powered two- and three-wheeler (PTW) riders are influenced by the rider posture. To enable analysis of PTW rider accidents and development of protection systems, detailed whole-body posture data is needed. Therefore, the aim of this study is to fill this gap by providing collections of average male whole-body postures, including subpopulation variability, for different PTW types. This will enable future studies to explore the influence of PTW rider posture variation and to support safety system development. METHODS: 3D photometric measurements of 51 anatomical landmarks were recorded on 20 (50th percentile male) volunteers in their preferred riding postures across three PTW types (naked, scooter, and touring). Following an outlier removal process, a principal component analysis (PCA) was performed to calculate average postures and principal components (PCs), to describe the observed posture variation, for each PTW. The visualization of the PCs was facilitated through kinematic linkage representations, connecting anatomical landmarks and estimated joint centers to form segments and characteristic joint angles. RESULTS: The first seven PCs explained 80% of the variance in posture for each of the three PTWs. Across PTWs, these PCs frequently described combinations of postural features including variation in fore-aft seat positions, pelvic tilt, spinal curvature, head position, and extremity flexion-extension. Analysis revealed distinct differences in average postures across the three PTWs, on average, 10 ± 9° for the characteristic joint angles within a min-to-max range between the three PTWs. However, for all three PTWs, the variability between volunteers in characteristic joint angles on the same PTW were on average more than twice as large within a ± 2 SD range (26 ± 11°). CONCLUSIONS: The results suggest that PTW rider posture variation must be addressed by involving simultaneous adjustments of multiple body parts, as described by each of the first seven PCs, as a direct consequence of the human body interconnectedness. Furthermore, the study's findings challenge conventional assumptions that the relative distance between PTWs' handlebar, seat, and foot support predominantly influences rider postures. Instead, the research demonstrates that individual variability has a substantial influence on rider posture and should be considered in PTW safety development.

Finite element human body models with active reflexive muscles suitable for sex based whiplash injury prediction.

Previous research has not produced a satisfactory resource to study reflexive muscle activity for investigating potentially injurious whiplash motions. Various experimental and computational studies are available, but none provided a comprehensive biomechanical representation of human response during rear impacts. Three objectives were addressed in the current study to develop female and male finite element human body models with active reflexive neck muscles: 1) eliminate the buckling in the lower cervical spine of the model observed in earlier active muscle controller implementations, 2) evaluate and quantify the influence of the individual features of muscle activity, and 3) evaluate and select the best model configuration that can be used for whiplash injury predictions. The current study used an open-source finite element model of the human body for injury assessment representing an average 50th percentile female anthropometry, together with the derivative 50th percentile male morphed model. Based on the head-neck kinematics and CORelation and Analyis (CORA) tool for evaluation, models with active muscle controller and parallel damping elements showed improved head-neck kinematics agreement with the volunteers over the passive models. It was concluded that this model configuration would be the most suitable for gender-based whiplash injury prediction when different impact severities are to be studied.

Design and Evaluation of the Initial 50th Percentile Female Prototype Rear Impact Dummy, BioRID P50F - Indications for the Need of an Additional Dummy Size.

The objective of this study was to present the design of a prototype rear impact crash test dummy, representing a 50th percentile female, and compare its performance to volunteer response data. The intention was to develop a first crude prototype as a first step toward a future biofidelic 50th percentile female rear impact dummy. The current rear impact crash test dummy, BioRID II, represents a 50th percentile male, which may limit the assessment and development of whiplash protection systems with regard to female occupants. Introduction of this new dummy size will facilitate evaluation of seat and head restraint (HR) responses in both the average sized female and male in rear impacts. A 50th percentile female rear impact prototype dummy, the BioRID P50F, was developed from modified body segments originating from the BioRID II. The mass and rough dimensions of the BioRID P50F is representative of a 50th percentile female. The prototype dummy was evaluated against low severity rear impact sled tests comprising six female volunteers closely resembling a 50th percentile female with regard to stature and mass. The head/neck response of the BioRID P50F prototype resembled the female volunteer response corridors. The stiffness of the thoracic and lumbar spinal joints remained the same as the average sized male BioRID II, and therefore likely stiffer than joints of an average female. Consequently, the peak rearward angular displacement of the head and T1, and the rearward displacement of the T1, were lesser for the BioRID P50F in comparison to the female volunteers. The biofidelity of the BioRID P50F prototype thus has some limitations. Based on a seat response comparison between the BioRID P50F and the BioRID II, it can be concluded that the male BioRID II is an insufficient representation of the average female in the assessment of the dynamic seat response and effectiveness of whiplash protection systems.

Dynamic Responses of Female Volunteers in Rear Impact Sled Tests at Two Head Restraint Distances.

The objective of this study was to assess the biomechanical and kinematic responses of female volunteers with two different head restraint (HR) configurations when exposed to a low-speed rear loading environment. A series of rear impact sled tests comprising eight belted, near 50th percentile female volunteers, seated on a simplified laboratory seat, was performed with a mean sled acceleration of 2.1 g and a velocity change of 6.8 km/h. Each volunteer underwent two tests; the first test configuration, HR10, was performed at the initial HR distance ∼10 cm and the second test configuration, HR15, was performed at ∼15 cm. Time histories, peak values and their timing were derived from accelerometer data and video analysis, and response corridors were also generated. The results were separated into three different categories, HR10 C (N = 8), HR15 C (N = 6), and HR15 N C (N = 2), based on: (1) the targeted initial HR distance [10 cm or 15 cm] and (2) whether the volunteers' head had made contact with the HR [Contact (C) or No Contact (NC)] during the test event. The results in the three categories deviated significantly. The greatest differences were found for the average peak head angular displacements, ranging from 10° to 64°. Furthermore, the average neck injury criteria (NIC) value was 22% lower in HR10 C (3.9 m2/s2), and 49% greater in HR15 N C (7.4 m2/s2) in comparison to HR15 C (5.0 m2/s2). This study supplies new data suitable for validation of mechanical or mathematical models of a 50th percentile female. A model of a 50th percentile female remains to be developed and is urgently required to complement the average male models to enhance equality in safety assessments. Hence, it is important that future protection systems are developed and evaluated with female properties taken into consideration too. It is likely that the HR15 test configuration is close to the limit for avoiding HR contact for this specific seat setup. Using both datasets (HR15 C and HR15 N C ), each with its corresponding HR contact condition, will be possible in future dummy or model evaluation.

Optimization of Female Head-Neck Model with Active Reflexive Cervical Muscles in Low Severity Rear Impact Collisions.

ViVA Open Human Body Model (HBM) is an open-source human body model that was developed to fill the gap of currently available models that lacked the average female size. In this study, the head-neck model of ViVA OpenHBM was further developed by adding active muscle controllers for the cervical muscles to represent the human neck muscle reflex system as studies have shown that cervical muscles influence head-neck kinematics during impacts. The muscle controller was calibrated by conducting optimization-based parameter identification of published-volunteer data. The effects of different calibration objectives to head-neck kinematics were analyzed and compared. In general, a model with active neck muscles improved the head-neck kinematics agreement with volunteer responses. The current study highlights the importance of including active muscle response to mimic the volunteer's kinematics. A simple PD controller has found to be able to represent the behavior of the neck muscle reflex system. The optimum gains that defined the muscle controllers in the present study were able to be identified using optimizations. The present study provides a basis for describing an active muscle controller that can be used in future studies to investigate whiplash injuries in rear impacts.

Relationship Between Cervical, Thoracic, and Lumbar Spinal Alignments in Automotive Seated Posture.

The purpose of this study was to investigate the relationship between cervical, thoracic, and lumbar spinal alignments in one automotive occupant seated posture. An image dataset of the spinal column in the automotive seated posture, previously acquired by an upright open magnetic resonance imaging (MRI) system, was re-analyzed in this study. Spinal alignments were presented by the geometrical centers of the vertebral bodies extracted from the image data. Cervical, thoracic, and lumbar spinal alignments were analyzed separately with multidimensional scaling (MDS). Based on distribution maps of cervical, thoracic, and lumbar spinal alignments created by MDS, representative spinal alignment patterns of the cervical, thoracic, and lumbar spines and the relationship between cervical, thoracic, and lumbar spinal alignments were investigated. As a result, this study found a correlation between cervical and thoracic spinal alignments in an automotive occupant seated posture. According to representative spinal alignment patterns illustrated by the distribution map of spinal alignments, subjects who had kyphotic cervical spinal alignment tended to have less kyphotic thoracic spinal alignment, while subjects who had lordotic cervical spinal alignment tended to have more kyphotic thoracic spinal alignment. For lumbar spinal alignments, no prominent relationship was found between cervical and thoracic spinal alignment in the seated condition of this study.

Comparison of control strategies for the cervical muscles of an average female head-neck finite element model.

Objective: ViVA OpenHBM is the first open source Human Body Model (HBM) for crash safety assessment. It represents an average size (50th percentile) female and was created to assess whiplash protection systems in a car. To increase the biofidelity of the current model, further enhancements are being made by implementing muscle reflex response capabilities as cervical muscles alter the head and neck kinematics of the occupant during low-speed rear crashes. The objective of this study was to assess how different neck muscle activation control strategies affect head-neck kinematics in low speed rear impacts.Methods: The VIVA OpenHBM head-neck model, previously validated to PMHS data, was used for this study. To represent the 34 cervical muscles, 129 beam elements with Hill-type material models were used. Two different muscle activation control strategies were implemented: a control strategy to mimic neural feedback from the vestibular system and a control strategy to represent displacement feedback from muscle spindles. To identify control gain values for these controller strategies, parameter calibrations were conducted using optimization. The objective of these optimizations was to match the head linear and angular displacements measured in volunteer tests.Results: Muscle activation changed the head kinematics by reducing the peak linear displacements, as compared to the model without muscle activation. For the muscle activation model mimicking the human vestibular system, a good agreement was observed for the horizontal head translation. However, in the vertical direction there was a discrepancy of head kinematic response caused by buckling of the cervical spine. In the model with a control strategy that represents muscle spindle feedback, improvements in translational head kinematics were observed and less cervical spine buckling was observed. Although, the overall kinematic responses were better in the first strategy.Conclusions: Both muscle control strategies improved the head kinematics compared to the passive model and comparable to the volunteer kinematics responses with overall better agreement achieved by the model with active muscles mimicking the human vestibular system.

Deformation of dorsal root ganglion due to pressure transients of venous blood and cerebrospinal fluid in the cervical vertebral canal.

The dorsal root ganglion (DRG) that is embedded in the foramen of the cervical vertebra can be injured during a whiplash motion. A potential cause is that whilst the neck bends in the whiplash motion, the changes of spinal canal volume induce impulsive pressure transients in the venous blood outside the dura mater (DM) and in the cerebrospinal fluid (CSF) inside the DM. The fluids can dynamically interact with the DRG and DM, which are deformable. In this work, the interaction is investigated numerically using a strong-coupling partitioned method that synchronize the computations of the fluid and structure. It is found that the interaction includes two basic processes, i.e., the pulling and pressing processes. In the pulling process, the DRG is stretched towards the spinal canal, and the venous blood is driven into the canal via the foramen. This process results from negative pressure in the fluids. In contrast, the pressing process is caused by positive pressure that leads to compression of the DRG and the outflow of the venous blood from the canal. The largest pressure gradient is observed at the foramen, where the DRG is located at. The DRG is subject to prominent von Mises stress near its end, which is fixed without motions. The negative internal pressure is more efficient to deform the DRG than the positive internal pressure. This indicates that the most hazardous condition for the DRG is the pulling process.

Average male and female virtual dummy model (BioRID and EvaRID) simulations with two seat concepts in the Euro NCAP low severity rear impact test configuration.

Soft tissue neck injuries, also referred to as whiplash injuries, which can lead to long term suffering accounts for more than 60% of the cost of all injuries leading to permanent medical impairment for the insurance companies, with respect to injuries sustained in vehicle crashes. These injuries are sustained in all impact directions, however they are most common in rear impacts. Injury statistics have since the mid-1960s consistently shown that females are subject to a higher risk of sustaining this type of injury than males, on average twice the risk of injury. Furthermore, some recently developed anti-whiplash systems have revealed they provide less protection for females than males. The protection of both males and females should be addresses equally when designing and evaluating vehicle safety systems to ensure maximum safety for everyone. This is currently not the case. The norm for crash test dummies representing humans in crash test laboratories is an average male. The female part of the population is not represented in tests performed by consumer information organisations such as NCAP or in regulatory tests due to the absence of a physical dummy representing an average female. Recently, the world first virtual model of an average female crash test dummy was developed. In this study, simulations were run with both this model and an average male dummy model, seated in a simplified model of a vehicle seat. The results of the simulations were compared to earlier published results from simulations run in the same test set-up with a vehicle concepts seat. The three crash pulse severities of the Euro NCAP low severity rear impact test were applied. The motion of the neck, head and upper torso were analysed in addition to the accelerations and the Neck Injury Criterion (NIC). Furthermore, the response of the virtual models was compared to the response of volunteers as well as the average male model, to that of the response of a physical dummy model. Simulations with the virtual male and female dummy models revealed differences in dynamic response related to the crash severity, as well as between the two dummies in the two different seat models. For the comparison of the response of the virtual models to the response of the volunteers and the physical dummy model, the peak angular motion of the first thoracic vertebra as found in the volunteer tests and mimicked by the physical dummy were not of the same magnitude in the virtual models. The results of the study highlight the need for an extended test matrix that includes an average female dummy model to evaluate the level of occupant protection different seats provide in vehicle crashes. This would provide developers with an additional tool to ensure that both male and female occupants receive satisfactory protection and promote seat concepts that provide the best possible protection for the whole adult population. This study shows that using the mathematical models available today can provide insights suitable for future testing.

A female head-neck model for rear impact simulations.

Several mathematical cervical models of the 50th percentile male have been developed and used for impact biomechanics research. However, for the 50th percentile female no similar modelling efforts have been made, despite females being subject to a higher risk of soft tissue neck injuries. This is a limitation for the development of automotive protective systems addressing Whiplash Associated Disorders (WADs), most commonly caused in rear impacts, as the risk for females sustaining WAD symptoms is double that of males. In this study, a finite element head and neck model of a 50th percentile female was validated in rear impacts. A previously validated ligamentous cervical spine model was complemented with a rigid body head, soft tissues and muscles. In both physiological flexion-extension motions and simulated rear impacts, the kinematic response at segment level was comparable to that of human subjects. Evaluation of ligament stress levels in simulations with varied initial cervical curvature revealed that if an individual assumes a more lordotic posture than the neutral, a higher risk of WAD might occur in rear impact. The female head and neck model, together with a kinematical whole body model which is under development, addresses a need for tools for assessment of automotive protection systems for the group which is at the highest risk to sustain WAD.

A Female Ligamentous Cervical Spine Finite Element Model Validated for Physiological Loads.

Mathematical cervical spine models allow for studying of impact loading that can cause whiplash associated disorders (WAD). However, existing models only cover the male anthropometry, despite the female population being at a higher risk of sustaining WAD in automotive rear-end impacts. The aim of this study is to develop and validate a ligamentous cervical spine intended for biomechanical research on the effect of automotive impacts. A female model has the potential to aid the design of better protection systems as well as improve understanding of injury mechanisms causing WAD. A finite element (FE) mesh was created from surface data of the cervical vertebrae of a 26-year old female (stature 167 cm, weight 59 kg). Soft tissues were generated from the skeletal geometry and anatomical literature descriptions. Ligaments were modeled with nonlinear elastic orthotropic membrane elements, intervertebral disks as composites of nonlinear elastic bulk elements, and orthotropic anulus fibrosus fiber layers, while cortical and trabecular bones were modeled as isotropic plastic-elastic. The model has geometrical features representative of the female cervical spine-the largest average difference compared with published anthropometric female data was the vertebral body depth being 3.4% shorter for the model. The majority the cervical segments compare well with respect to biomechanical data at physiological loads, with the best match for flexion-extension loads and less biofidelity for axial rotation. An average female FE ligamentous cervical spine model was developed and validated with respect to physiological loading. In flexion-extension simulations with the developed female model and an existing average male cervical spine model, a greater range of motion (ROM) was found in the female model.

Transient pressure changes in the vertebral canal during whiplash motion--A hydrodynamic modeling approach.

In vehicle collisions, the occupant's torso is accelerated in a given direction while the unsupported head tends to lag behind. This mechanism results in whiplash motion to the neck. In whiplash experiments conducted for animals, pressure transients have been recorded in the spinal canal. It was hypothesized that the transients caused dorsal root ganglion dysfunction. Neck motion introduces volume changes inside the vertebral canal. The changes require an adaptation which is likely achieved by redistribution of blood volume in the internal vertebral venous plexus (IVVP). Pressure transients then arise from the rapid redistribution. The present study aimed to explore the hypothesis theoretically and analytically. Further, the objectives were to quantify the effect of the neck motion on the pressure generation and to identify the physical factors involved. We developed a hydrodynamic system of tubes that represent the IVVP and its lateral intervertebral vein connections. An analytical model was developed for an anatomical geometrical relation that the venous blood volume changes with respect to the vertebral angular displacement. This model was adopted in the hydrodynamic tube system so that the system can predict the pressure transients on the basis of the neck vertebral motion data from a whiplash experiment. The predicted pressure transients were in good agreement with the earlier experimental data. A parametric study was conducted and showed that the system can be used to assess the influences of anatomical geometrical properties and vehicle collision severity on the pressure generation.

Impacts to the chest of PMHSs - Influence of impact location and load distribution on chest response.

The chest response of the human body has been studied for several load conditions, but is not well known in the case of steering wheel rim-to-chest impact in heavy goods vehicle frontal collisions. The aim of this study was to determine the response of the human chest in a set of simulated steering wheel impacts. PMHS tests were carried out and analysed. The steering wheel load pattern was represented by a rigid pendulum with a straight bar-shaped front. A crash test dummy chest calibration pendulum was utilised for comparison. In this study, a set of rigid bar impacts were directed at various heights of the chest, spanning approximately 120mm around the fourth intercostal space. The impact energy was set below a level estimated to cause rib fracture. The analysed results consist of responses, evaluated with respect to differences in the impacting shape and impact heights on compression and viscous criteria chest injury responses. The results showed that the bar impacts consistently produced lesser scaled chest compressions than the hub; the Middle bar responses were around 90% of the hub responses. A superior bar impact provided lesser chest compression; the average response was 86% of the Middle bar response. For inferior bar impacts, the chest compression response was 116% of the chest compression in the middle. The damping properties of the chest caused the compression to decrease in the high speed bar impacts to 88% of that in low speed impacts. From the analysis it could be concluded that the bar impact shape provides lower chest criteria responses compared to the hub. Further, the bar responses are dependent on the impact location of the chest. Inertial and viscous effects of the upper body affect the responses. The results can be used to assess the responses of human substitutes such as anthropomorphic test devices and finite element human body models, which will benefit the development process of heavy goods vehicle safety systems.

Anthropometric specifications, development, and evaluation of EvaRID--a 50th percentile female rear impact finite element dummy model.

OBJECTIVES: Whiplash-associated disorders (WADs), or whiplash injuries, due to low-severity vehicle crashes are of great concern in motorized countries and it is well established that the risk of such injuries is higher for females than for males, even in similar crash conditions. Recent protective systems have been shown to be more beneficial for males than for females. Hence, there is a need for improved tools to address female WAD prevention when developing and evaluating the performance of whiplash protection systems. The objective of this study is to develop and evaluate a finite element model of a 50th percentile female rear impact crash test dummy. METHODS: The anthropometry of the 50th percentile female was specified based on literature data. The model, called EvaRID (female rear impact dummy), was based on the same design concept as the existing 50th percentile male rear impact dummy, the BioRID II. A scaling approach was developed and the first version, EvaRID V1.0, was implemented. Its dynamic response was compared to female volunteer data from rear impact sled tests. RESULTS: The EvaRID V1.0 model and the volunteer tests compared well until ∼250 ms of the head and T1 forward accelerations and rearward linear displacements and of the head rearward angular displacement. Markedly less T1 rearward angular displacement was found for the EvaRID model compared to the female volunteers. Similar results were received for the BioRID II model when comparing simulated responses with experimental data under volunteer loading conditions. The results indicate that the biofidelity of the EvaRID V1.0 and BioRID II FE models have limitations, predominantly in the T1 rearward angular displacement, at low velocity changes (7 km/h). The BioRID II model was validated against dummy test results in a loading range close to consumer test conditions (EuroNCAP) and lower severity levels of volunteer testing were not considered. CONCLUSIONS: The EvaRID dummy model demonstrated the potential of becoming a valuable tool when evaluating and developing seats and whiplash protection systems. However, updates of the joint stiffness will be required to provide better correlation at lower load levels. Moreover, the seated posture, curvature of the spine, and head position of 50th percentile female occupants needs to be established and implemented in future models.

Improving Hybrid III injury assessment in steering wheel rim to chest impacts using responses from finite element Hybrid III and human body model.

OBJECTIVE: The main aim of this study was to improve the quality of injury risk assessments in steering wheel rim to chest impacts when using the Hybrid III crash test dummy in frontal heavy goods vehicle (HGV) collision tests. Correction factors for chest injury criteria were calculated as the model chest injury parameter ratios between finite element (FE) Hybrid III, evaluated in relevant load cases, and the Total Human Model for Safety (THUMS). This is proposed to be used to compensate Hybrid III measurements in crash tests where steering wheel rim to chest impacts occur. METHODS: The study was conducted in an FE environment using an FE-Hybrid III model and the THUMS. Two impactor shapes were used, a circular hub and a long, thin horizontal bar. Chest impacts at velocities ranging from 3.0 to 6.0 m/s were simulated at 3 impact height levels. A ratio between FE-Hybrid III and THUMS chest injury parameters, maximum chest compression C max, and maximum viscous criterion VC max, were calculated for the different chest impact conditions to form a set of correction factors. The definition of the correction factor is based on the assumption that the response from a circular hub impact to the middle of the chest is well characterized and that injury risk measures are independent of impact height. The current limits for these chest injury criteria were used as a basis to develop correction factors that compensate for the limitations in biofidelity of the Hybrid III in steering wheel rim to chest impacts. RESULTS: The hub and bar impactors produced considerably higher C max and VC max responses in the THUMS compared to the FE-Hybrid III. The correction factor for the responses of the FE-Hybrid III showed that the criteria responses for the bar impactor were consistently overestimated. Ratios based on Hybrid III and THUMS responses provided correction factors for the Hybrid III responses ranging from 0.84 to 0.93. These factors can be used to estimate C max and VC max values when the Hybrid III is used in crash tests for which steering wheel rim to chest interaction occurs. CONCLUSIONS: For the FE-Hybrid III, bar impacts caused higher chest deflection compared to hub impacts, although the contrary results were obtained with the more humanlike THUMS. Correction factors were developed that can be used to correct the Hybrid III chest responses. Higher injury criteria capping limits for steering wheel impacts are acceptable. Supplemental materials are available for this article. Go to the publisher's online edition of Traffic Injury Prevention to view the supplemental file.

Motion of the head and neck of female and male volunteers in rear impact car-to-car impacts.

OBJECTIVES: The objectives of this study were to quantify and compare dynamic motion responses between 50th percentile female and male volunteers in rear impact tests. These data are fundamental for developing future occupant models for crash safety development and assessment. METHODS: High-speed video data from a rear impact test series with 21 male and 21 female volunteers at 4 and 8 km/h, originally presented in Siegmund et al. (1997), were used for further analysis. Data from a subset of female volunteers, 12 at 4 km/h and 9 at 8 km/h, were extracted from the original data set to represent the 50th percentile female. Their average height was 163 cm and their average weight was 62 kg. Among the male volunteers, 11 were selected, with an average height of 175 cm and an average weight of 73 kg, to represent the 50th percentile male. Response corridors were generated for the horizontal and angular displacements of the head, T1 (first thoracic vertebra), and the head relative to T1. T-tests were performed with the statistical significance level of .05 to quantify the significance of the differences in parameter values for the males and females. RESULTS: Several differences were found in the average motion response of the male and female volunteers at 4 and 8 km/h. Generally, females had smaller rearward horizontal and angular motions of the head and T1 compared to the males. This was mainly due to shorter initial head-to-head restraint distance and earlier head-to-head restraint contact for the females. At 8 km/h, the female volunteers showed 12 percent lower horizontal peak rearward head displacement (P = .018); 22 percent lower horizontal peak rearward head relative to T1 displacement (P = .018); and 30 percent lower peak head extension angle (P = .001). The females also had more pronounced rebound motion. CONCLUSIONS: This study indicates that there may be characteristic differences in the head-neck motion response between 50th percentile males and females in rear impacts. The exclusive use of 50th percentile male rear impact dummies may thus limit the assessment and development of whiplash prevention systems that adequately protect both male and female occupants. The results of this study could be used in the development and evaluation of a mechanical and/or computational average-sized female dummy model for rear impact safety assessment. These models are used in the development and evaluation of protective systems. It would be of interest to make further studies into seat configurations featuring a greater head-to-head restraint distance.

The anatomy and biomechanics of acute and chronic whiplash injury.

Whiplash injury is the most common motor vehicle injury, yet it is also one of the most poorly understood. Here we examine the evidence supporting an organic basis for acute and chronic whiplash injuries and review the anatomical sites within the neck that are potentially injured during these collisions. For each proposed anatomical site--facet joints, spinal ligaments, intervertebral discs, vertebral arteries, dorsal root ganglia, and neck muscles--we present the clinical evidence supporting that injury site, its relevant anatomy, the mechanism of and tolerance to injury, and the future research needed to determine whether that site is responsible for some whiplash injuries. This article serves as a snapshot of the current state of whiplash biomechanics research and provides a roadmap for future research to better understand and ultimately prevent whiplash injuries.

Dynamic responses of female and male volunteers in rear impacts.

OBJECTIVES: Whiplash injuries from vehicle collisions are common and costly. These injuries most frequently occur as a result of a rear impact and, compared to males, females have up to twice the risk of whiplash-associated disorders (WAD) resulting from vehicle crashes. The present study focuses on the differences in the dynamic response corridors of males and females in low-severity rear impacts. METHODS: In this study, analysis of data from volunteer tests of females from previously published data has been performed. Corridors for the average female response were generated based on 12 volunteers exposed to a change of velocity of 4 km/h and 9 volunteers exposed to a change of velocity of 8 km/h. These corridors were compared to corridors for the average male response that were previously generated based on 11 male volunteers exposed to the same test conditions. RESULTS: Comparison between the male and female data showed that the maximum x-acceleration of the head for the females occurred on average 10 ms earlier and was 29% higher during the 4 km/h test and 12 ms earlier and 9% higher during the 8 km/h test. Head-to-head restraint contact for the females occurred 14 ms earlier at 4 km/h and 11 ms earlier at 8 km/h compared to the males. For the same initial head-to-head restraint distance, head restraint contact occurred 11 and 7 ms earlier for the females than the males at 4 and 8 km/h, respectively. Furthermore, the calculated Neck Injury Criteria (NIC) values were similar for males and females at 4 km/h, whereas they were lower for females compared to the males at 8 km/h (3.2 and 4.0 m(2)/s(2), respectively). CONCLUSIONS: The results of this study highlight the need to further investigate the differences in dynamic responses between males and females at low-severity impacts. Such data are fundamental for the development of future computer models and dummies for crash safety assessment. These models can be used not only as a tool in the design and development process of protective systems but also in the process of further evaluation and development of injury criteria.