Impact of the Heat Treatment Duration on Color and Selected Mechanical and Chemical Properties of Scots Pine Wood.

The aim of this study was to assess the effect of the duration of heat treatment on changes in the color, as well as the chemical and mechanical properties of Scots pine sapwood. An important element of the research was to obtain the assumed temperature in the entire volume of samples. Quantitative changes in color and its components were recorded, while mechanical properties were determined in tests of compressive strength parallel and perpendicular to the grain, longitudinal tensile strength and modulus of elasticity and impact strength. The novelty of the research was to determine the above-mentioned parameters for twin samples with identical moisture contents. Chemical analyses were conducted on heat-treated wood that was subjected to heat treatment at 220 °C for a period from 1 to 8 h. Extension of the heat treatment duration resulted in the increasing darkening of the wood, as well as a further reduction in the impact strength and tensile strength parallel to the grain by approx. 40 and 50%, respectively, compared to the control wood, but also compared to heat-treated wood for a shorter treatment duration. The heat treatment of wood caused changes in the contents of the wood components, as well as the elemental composition in the heat-treated wood, compared to the control pine. The changes in the structure of the heat-treated wood were confirmed by the attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR). Observed quantitative changes in the main wood components, its structural changes, as well as wood decomposition and increased crystallinity of cellulose explain significant changes in both the mechanical properties and the color of heat-treated wood.

Color as an Indicator of Properties in Thermally Modified Scots Pine Sapwood.

The aim of this study was to determine the dependencies between mechanical properties of modified wood and its color. Within its scope, quantitative changes in color and chemical composition (mass loss, total carbon content, content of extractives and main components of wood), as well as mechanical properties (compressive strength along the grain, strength and modulus of elasticity in longitudinal tension tests, compression across the grain and impact resistance) of the modified Scots pine sapwood, were determined. Modifications were conducted in the atmosphere of superheated steam (time-4 h, temperature of 130, 160, 190, 220 °C). Thermal modification of wood results in an increase in the modulus of elasticity, a reduction of elasticity, longitudinal tensile strength and compressive strength perpendicular to grain. It was found that color parameters ∆E, ∆L and ∆a are linear functions of the modification temperature. The existence of functional dependencies between mass loss, longitudinal tensile strength, radial modulus of elasticity and parameters of ∆E and ∆L makes it possible to determine these properties of modified wood based on color. In turn, chemical analysis indicated that an increase in the temperature of wood modification caused a decrease of holocellulose and hemicelluloses contents, especially in wood samples modified at 220 °C.

Nanocellulose Production Using Ionic Liquids with Enzymatic Pretreatment.

Nanocellulose has gained increasing attention during the past decade, which is related to its unique properties and wide application. In this paper, nanocellulose samples were produced via hydrolysis with ionic liquids (1-ethyl-3-methylimidazole acetate (EmimOAc) and 1-allyl-3-methylimidazolium chloride (AmimCl)) from microcrystalline celluloses (Avicel and Whatman) subjected to enzymatic pretreatment. The obtained material was characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), dynamic light scattering (DLS), scanning electron microscopy (SEM), and thermogravimetric analysis (TG). The results showed that the nanocellulose had a regular and spherical structure with diameters of 30-40 nm and exhibited lower crystallinity and thermal stability than the material obtained after hydrolysis with Trichoderma reesei enzymes. However, the enzyme-pretreated Avicel had a particle size of about 200 nm and a cellulose II structure. A two-step process involving enzyme pretreatment and hydrolysis with ionic liquids resulted in the production of nanocellulose. Moreover, the particle size of nanocellulose and its structure depend on the ionic liquid used.

Production of Nanocellulose by Enzymatic Treatment for Application in Polymer Composites.

In the last few years, the scientific community around the world has devoted a lot of attention to the search for the best methods of obtaining nanocellulose. In this work, nanocellulose was obtained in enzymatic reactions with strictly defined dispersion and structural parameters in order to use it as a filler for polymers. The controlled enzymatic hydrolysis of the polysaccharide was carried out in the presence of cellulolytic enzymes from microscopic fungi-Trichoderma reesei and Aspergillus sp. It has been shown that the efficiency of bioconversion of cellulose material depends on the type of enzymes used. The use of a complex of cellulases obtained from a fungus of the genus Trichoderma turned out to be an effective method of obtaining cellulose of nanometric dimensions with a very low polydispersity. The effect of cellulose enzymatic reactions was assessed using the technique of high-performance liquid chromatography coupled with a refractometric detector, X-ray diffraction, dynamic light scattering and Fourier transform infrared spectroscopy. In the second stage, polypropylene composites with nanometric cellulose were obtained by extrusion and injection. It was found by means of X-ray diffraction, hot stage optical microscopy and differential scanning calorimetry that nanocellulose had a significant effect on the supermolecular structure, nucleation activity and the course of phase transitions of the obtained polymer nanocomposites. Moreover, the obtained nanocomposites are characterized by very good strength properties. This paper describes for the first time that the obtained cellulose nanofillers with defined parameters can be used for the production of polymer composites with a strictly defined polymorphic structure, which in turn may influence future decision making about obtaining materials with controllable properties, e.g., high flexibility, enabling the thermoforming process of packaging.

Chemical and Structural Characterization of Maize Stover Fractions in Aspect of Its Possible Applications.

In the last decade, an increasingly common method of maize stover management is to use it for energy generation, including anaerobic digestion for biogas production. Therefore, the aim of this study was to provide a chemical and structural characterization of maize stover fractions and, based on these parameters, to evaluate the potential application of these fractions, including for biogas production. In the study, maize stover fractions, including cobs, husks, leaves and stalks, were used. The biomass samples were characterized by infrared spectroscopy (FTIR), X-ray diffraction and analysis of elemental composition. Among all maize stover fractions, stalks showed the highest C:N ratio, degree of crystallinity and cellulose and lignin contents. The high crystallinity index of stalks (38%) is associated with their high cellulose content (44.87%). FTIR analysis showed that the spectrum of maize stalks is characterized by the highest intensity of bands at 1512 cm-1 and 1384 cm-1, which are the characteristic bands of lignin and cellulose. Obtained results indicate that the maize stover fraction has an influence on the chemical and structural parameters. Moreover, presented results indicate that stalks are characterized by the most favorable chemical parameters for biogas production.

Arsenic uptake, speciation and physiological response of tree species (Acer pseudoplatanus, Betula pendula and Quercus robur) treated with dimethylarsinic acid.

The aim of the study was to evaluate the effect of dimethylarsinic acid (DMA) on growth parameters and levels of stress-related metabolites in Acer pseudoplatanus, Betula pendula and Quercus robur. The increase of DMA concentration in the solution led to a notable growth retardation of trees. An intense As accumulation (mainly As(III) and As(V)) expressed as BCF and TF > 1 was recorded only for Q. robur. Generally a decrease in contents of cellulose, hemicellulose and holocellulose with a simultaneous increase in lignin content were recorded. Phenolic composition of leaf extracts was modified by DMA, while root and rhizosphere extracts were poor in phenolics. Toxicity of DMA leads to a significant drop in salicylic acid content in leaves observed at lower doses. Higher DMA levels caused a second, probably ROS-derived depletion of the metabolite accompanied with a severe growth retardation, most pronounced in the case of B. pendula. DMA caused the inhibition of LMWOA biosynthesis in roots of A. pseudoplatanus, B. pendula and their exudation into the rhizosphere, while in Q. robur roots and leaves a stimulation of their accumulation was observed. Disturbances in the activity of enzymatic antioxidants were observed for all the species following the increasing level of DMA.

Plant Cell Wall Changes in Common Wheat Roots as a Result of Their Interaction with Beneficial Fungi of Trichoderma.

Plant cell walls play an important role in shaping the defense strategies of plants. This research demonstrates the influence of two differentiators: the lifestyle and properties of the Trichoderma species on cell wall changes in common wheat seedlings. The methodologies used in this investigation include microscopy observations and immunodetection. In this study was shown that the plant cell wall was altered due to its interaction with Trichoderma. The accumulation of lignins and reorganization of pectin were observed. The immunocytochemistry indicated that low methyl-esterified pectins appeared in intercellular spaces. Moreover, it was found that the arabinogalactan protein epitope JIM14 can play a role in the interaction of wheat roots with both the tested Trichoderma strains. Nevertheless, we postulate that modifications, such as the appearance of lignins, rearrangement of low methyl-esterified pectins, and arabinogalactan proteins due to the interaction with Trichoderma show that tested strains can be potentially used in wheat seedlings protection to pathogens.

Enzymatic hydrolysis of cellulose using extracts from insects.

The use of Zophobas morio extracts in the aspect of cellulose hydrolysis is presented for the first time. The aim of this study was to investigate the action of enzymes obtained from Z. morio on cellulose hydrolysis and to determine their influence on the structural properties of cellulose with use the Fourier transform infrared spectroscopy (FTIR) and gel permeation chromatography (GPC). Cellulose hydrolysis products were analyzed by high performance liquid chromatography (HPLC). This analysis indicated that microcrystalline cellulose with smaller particle size was more susceptible to enzymatically treatment. Moreover, our investigation of cellulase activity showed a different profile of the used enzyme during particular developmental stages of Z. morio. Midgut extracts obtained from adult insects are more effective in degrading cellulose than extracts from larvae. The analysis of cellulose hydrolysis confirms that the efficiency of this reaction also depends on the structure of cellulosic materials and internal conditions of enzymatic reaction. In this study the cellulolytic activity of Z. morio midgut extracts showed that these insects could be valuable sources of cellulases.

Biological diversity of Salix taxa in Cu, Pb and Zn phytoextraction from soil.

The aim of the study was to estimate the efficiency of copper (Cu), lead (Pb) and zinc (Zn) phytoextraction by 145 Salix taxa cultivated in an area affected by industrial activity. Survivability and biomass of plants were also analyzed. The highest Cu, Pb and Zn content in shoots was 33.38 ± 2.91 (S. purpurea × viminalis 8), 24.64 ± 1.97 (S. fragilis 1) and 58.99 ± 4.30 (S. eriocephala 7) mg kg-1 dry weight, respectively. In the case of unwashed leaves, the highest content of these metals was 135.06 ± 8.14 (S. purpurea 26), 67.98 ± 5.27 (S. purpurea 45) and 142.56 ± 12.69 (S. alba × triandra 2) mg kg-1 dw, while in washed leaves it was 106.02 ± 11.12 (S. purpurea 45), 55.06 ± 5.75 (S. purpurea 45) and 122.87 ± 12.33 (S. alba × triandra 2) mg kg-1 dw, respectively. The differences between the highest and lowest values for Cu, Pb and Zn were 545%, 20500% and 535% in shoots; 2692%, 2560% and 7500% in unwashed leaves; and 3286%, 2221% and 6950% in washed leaves, respectively. S. acutifolia was able to effectively accumulate all three metals jointly, producing shoots that were well developed in both length and diameter when compared with the other tested willows-an ability that would suggest its high suitability for practical application.