Climbing the Hydrogen Evolution Volcano with a NiTi Shape Memory Alloy.

Alkaline water electrolysis is a sustainable way to produce green hydrogen using renewable electricity. Even though the rates of the cathodic hydrogen evolution reaction (HER) are 2-3 orders of magnitude less under alkaline conditions than under acidic conditions, the possibility of using non-precious metal catalysts makes alkaline HER appealing. We identify a novel and facile route for substantially improving HER performance via the use of commercially available NiTi shape memory alloys, which upon heating undergo a phase transformation from the monoclinic martensite to the cubic austenite structure. While the room-temperature performance is modest, austenitic NiTi outperforms Pt (which is the state-of-the-art HER electrocatalyst) in terms of current density by ≤50% at 80 °C. Surface ensembles presented by the austenite phase are computed with density functional theory to bind hydrogen more weakly than either metallic Ni or Ti and to have binding energies ideally suited for HER.

Controlled amino-functionalization by electrochemical reduction of bromo and nitro azobenzene layers bound to Si(111) surfaces.

4-Nitrobenzenediazonium (4-NBD) and 4-bromobenzenediazonium (4-BBD) salts were grafted electrochemically onto H-terminated, p-doped silicon (Si) surfaces. Atomic force microscopy (AFM) and ellipsometry experiments clearly showed layer thicknesses of 2-7 nm, which indicate multilayer formation. Decreasing the diazonium salt concentration and the reaction time resulted in a smaller layer thickness, but did not prevent the formation of multilayers. It was demonstrated, mainly by X-ray photoelectron spectroscopy (XPS), that the diazonium salts not only react with the H-terminated Si surface, but also with electrografted phenyl groups via azo-bond formation. These azo bonds can be electrochemically reduced at Ered = -1.5 V, leading to the corresponding amino groups. This reduction resulted in a modest decrease in layer thickness, and did not yield monolayers. This indicates that other coupling reactions, notably a biphenyl coupling, induced by electrochemically produced phenyl radicals, take place as well. In addition to the azo functionalities, the nitro functionalities in electrografted layers of 4-NBD were independently reduced to amino functionalities at a lower potential (Ered = -2.1 V). The presence of amino functionalities on fully reduced layers, both from 4-NBD- and 4-BBD-modified Si, was shown by the presence of fluorine after reaction with trifluoroacetic anhydride (TFAA). This study shows that the electrochemical reduction of azo bonds generates amino functionalities on layers produced by electrografting of aryldiazonium derivatives. In this way multifunctional layers can be formed by employing functional aryldiazonium salts, which is believed to be very practical in the fabrication of sensor platforms, including those made of multi-array silicon nanowires.

New Cu-based catalysts supported on TiO2 films for Ullmann S(N)Ar-type C-O coupling reactions.

New routes for the preparation of highly active TiO(2)-supported Cu and CuZn catalysts have been developed for C-O coupling reactions. Slurries of a titania precursor were dip-coated onto glass beads to obtain either structured mesoporous or non-porous titania thin films. The Cu and CuZn nanoparticles, synthesized using a reduction by solvent method, were deposited onto calcined films to obtain a Cu loading of 2 wt%. The catalysts were characterized by inductively coupled plasma (ICP) spectroscopy, temperature-programmed oxidation/reduction (TPO/TPR) techniques, (63)Cu nuclear magnetic resonance (NMR) spectroscopy, X-ray diffraction (XRD), scanning and transmission electron microscopy (S/TEM-EDX) and X-ray photo-electron spectroscopy (XPS). The activity and stability of the catalysts obtained have been studied in the C-O Ullmann coupling of 4-chloropyridine and potassium phenolate. The titania-supported nanoparticles retained catalyst activity for up to 12 h. However, catalyst deactivation was observed for longer operation times due to oxidation of the Cu nanoparticles. The oxidation rate could be significantly reduced over the CuZn/TiO(2) catalytic films due to the presence of Zn. The 4-phenoxypyridine yield was 64% on the Cu/nonporous TiO(2) at 120 °C. The highest product yield of 84% was obtained on the Cu/mesoporous TiO(2) at 140 °C, corresponding to an initial reaction rate of 104 mmol g(cat) (-1) s(-1). The activation energy on the Cu/mesoporous TiO(2) catalyst was found to be (144±5) kJ mol(-1), which is close to the value obtained for the reaction over unsupported CuZn nanoparticles (123±3 kJ mol(-1)) and almost twice the value observed over the catalysts deposited onto the non-porous TiO(2) support (75±2 kJ mol(-1)).

In situ ATR-FTIR studies on MgCl2-diisobutyl phthalate interactions in thin film Ziegler-Natta catalysts.

To study the surface structure of MgCl(2) support and its interaction with other active components in Ziegler-Natta catalyst, such as electron donors, we prepared a thin film analogue for Ziegler-Natta ethylene polymerization catalyst support by spin-coating a solution of MgCl(2) in ethanol, optionally containing a diester internal donor (diisobutyl-ortho-phthalate, DIBP) on a flat Si crystal surface. The donor content of these films was quantified by applying attenuated total internal reflection-Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). Changes in the interaction of DIBP with MgCl(2) at various temperatures were monitored by in situ ATR-FTIR. Upon increasing the temperature, a shift in the (C═O) band toward lower wavenumbers was observed together with the depletion of (O-H) stretching band due to the desorption of residual ethanol. We assign this shift to gradual redistribution of adsorbed DIBP from adsorption sites on the MgCl(2) (104) surface toward the more acidic MgCl(2) (110) surface. The morphologies of MgCl(2) and MgCl(2)/DIBP films were studied by transmission electron microscopy (TEM) revealing a preferential orientation of ClMgCl layers (001) parallel to the lateral film dimensions. This orientation becomes more pronounced upon annealing. In the absence of donor, the MgCl(2) grow in to large crystals aligned in large domains upon annealing. Both crystal growth and alignment is impeded by the presence of donor.

An injectable calcium phosphate cement for the local delivery of paclitaxel to bone.

Bone metastases are usually treated by surgical removal, fixation and chemotherapeutic treatment. Bone cement is used to fill the resection voids. The aim of this study was to develop a local drug delivery system using a calcium phosphate cement (CPC) as carrier for chemotherapeutic agents. CPC consisted of alpha-tricalcium phosphate, calcium phosphate dibasic and precipitated hydroxyapatite powders and a 2% Na(2)HPO(4) hardening solution. Scanning electron microscopy (SEM) was used to observe CPC morphology. X-ray diffraction (XRD) was used to follow CPC transformation. The loading/release capacity of the CPC was studied by a bovine serum albumin-loading model. Release/retention was measured by high performance liquid chromatography and X-ray photoelectron spectrometry. For chemotherapeutic loading, paclitaxel (PX) was loaded onto the CPC discs by absorption. Viability of osteosarcoma U2OS and metastatic breast cancer MDA-MB-231 cells was measured by an AlamarBlue assay. Results of SEM and XRD showed changes in CPC due to its transformation. The loading model indicated a high retention behavior by the CPC composition. Cell viability tests indicated a PX minimal lethal dose of 90 µg/ml. PX released from CPC remained active to influence cell viability. In conclusion, this study demonstrated that CPC is a feasible delivery vector for chemotherapeutic agents.

Nanoparticulate PdZn--pathways towards the synthetic control of nanosurface properties.

This paper reports an in-depth structural investigation of PdZn nanoparticulates prepared over an entire compositional range. By using a combination of HRTEM, ICP-OES, EDX and XPS alongside PXRD, we are able to show how a liquid-type reduction process can be exploited to target different PdZn bimetallic structures while maintaining reproducibly narrow particle size distributions and average particle diameters of approximately 3 nm. Samples have been further analyzed by quantitative phase analysis of the Rietveld refined diffraction data, providing indications as to how variations in specific surface compositions are obtained when Zn is used as the alloying metal. The influence of nanolattice strain is investigated by geometric analysis of TEM data. Results suggest, in conjunction with previously published catalytic data, how different compositions of this specific bimetallic system may be exploited in catalytic processes to control substrate/product affinity. We thus demonstrate a new and simplified approach to PdZn bimetallics, which may offer novel perspectives for applications in industrial catalysis.

Cellulose nanocrystal submonolayers by spin coating.

Dilute concentrations of cellulose nanocrystal solutions were spin coated onto different substrates to investigate the effect of the substrate on the nanocrystal submonolayers. Three substrates were probed: silica, titania, and amorphous cellulose. According to atomic force microscopy (AFM) images, anionic cellulose nanocrystals formed small aggregates on the anionic silica substrate, whereas a uniform two-dimensional distribution of nanocrystals was achieved on the cationic titania substrate. The uniform distribution of cellulose nanocrystal submonolayers on titania is an important factor when dimensional analysis of the nanocrystals is desired. Furthermore, the amount of nanocrystals deposited on titania was multifold in comparison to the amounts on silica, as revealed by AFM image analysis and X-ray photoelectron spectroscopy. Amorphous cellulose, the third substrate, resulted in a somewhat homogeneous distribution of the nanocrystal submonolayers, but the amounts were as low as those on the silica substrate. These differences in the cellulose nanocrystal deposition were attributed to electrostatic effects: anionic cellulose nanocrystals are adsorbed on cationic titania in addition to the normal spin coating deposition. The anionic silica surface, on the other hand, causes aggregation of the weakly anionic cellulose nanocrystals which are forced on the repulsive substrate by spin coating. The electrostatically driven adsorption also influences the film thickness of continuous ultrathin films of cellulose nanocrystals. The thicker films of charged nanocrystals on a substrate of opposite charge means that the film thickness is not independent of the substrate when spin coating cellulose nanocrystals in the ultrathin regime (<100 nm).

Direct catalytic route to superhydrophobic polyethylene films.

Polyethylene films grow on a flat silica surface modified by the bis(imino)pyridyl iron(II) catalyst during ethylene polymerization in toluene solvent. The resulting films show superhydrophobic properties. Advancing water contact angle as high as 169 degrees and sliding angles as low as 2 degrees are obtained on these films. SEM images reveal special surface structures of these films containing micrometer-sized islands, submicrometer particles on the islands, and stress nanofibers between the islands, which render superhydrophobicity to the polyethylene surfaces. After the submicrometer particles and stress nanofibers are removed by annealing, the superhydrophobic properties of the polymer films disappear.

Fabrication, characterization, and biological assessment of multilayered DNA-coatings for biomaterial purposes.

This study describes the fabrication of two types of multilayered coatings onto titanium by electrostatic self-assembly (ESA), using deoxyribosenucleic acid (DNA) as the anionic polyelectrolyte and poly-d-lysine (PDL) or poly(allylamine hydrochloride) (PAH) as the cationic polyelectrolyte. Both coatings were characterized using UV-vis spectrophotometry, atomic force microscopy (AFM), X-ray photospectroscopy (XPS), contact angle measurements, Fourier transform infrared spectroscopy (FTIR), and for the amount of DNA immobilized. The mutagenicity of the constituents of the coatings was assessed. Titanium substrates with or without multilayered DNA-coatings were used in cell culture experiments to study cell proliferation, viability, and morphology. Results of UV-vis spectrophotometry, AFM, and contact angle measurements clearly indicated the progressive build-up of the multilayered coatings. Furthermore, AFM and XPS data showed a more uniform build-up and morphology of [PDL/DNA]-coatings compared to [PAH/DNA]-coatings. DNA-immobilization into both coatings was linear, and approximated 3microg/cm(2) into each double-layer. The surface morphology of both types of multilayered DNA-coatings showed elevations in the nanoscale range. No mutagenic effects of DNA, PDL, or PAH were detected, and cell viability and morphology were not affected by the presence of either type of multilayered DNA-coating. Still, the results of the proliferation assay revealed an increased proliferation of primary rat dermal fibroblasts on both types of multilayered DNA-coatings compared to non-coated controls. The biocompatibility and functionalization of the coatings produced here, will be assessed in subsequent cell culture and animal-implantation studies.

Covalently attached monolayers on crystalline hydrogen-terminated silicon: extremely mild attachment by visible light.

A very mild method was developed for the attachment of high-quality organic monolayers on crystalline silicon surfaces. By using visible light sources, from 447 to 658 nm, a variety of 1-alkenes and 1-alkynes were attached to hydrogen-terminated Si(100) and Si(111) surfaces at room temperature. The presence and the quality of the monolayers were evaluated by static water contact angles, X-ray photoelectron spectroscopy, and IR spectroscopy. Monolayers prepared by thermal, UV light, or visible light initiation were compared. Additionally, the ability of infrared reflection-absorption spectroscopy to study organic monolayers on silicon was explored. A reaction mechanism is discussed on the basis of investigations of the reaction behavior of 1-alkenes with silicon wafers with varying types and levels of doping. Finally, a series of mixed monolayers derived from the mixed solutions of a 1-alkene and an omega-fluoro-1-alkene were investigated to reveal that the composition of the mixed monolayers was directly proportional to the molar ratio of the two compounds in the solutions.