Low ice adhesion on soft surfaces: Elasticity or lubrication effects?

HYPOTHESIS: Soft materials are promising candidates for designing passive de-icing systems. It is unclear whether low adhesion on soft surfaces is due to elasticity or lubrication, and how these properties affect the ice detachment mechanism. This study presents a systematic analysis of ice adhesion on soft materials with different lubricant content to better understand the underpinning interaction. EXPERIMENTS: The wetting and mechanical properties of soft polydimethylsiloxane with different lubricant content were thoroughly characterized by contact angle, AFM indentation, and rheology measurements. The collected information was used to understand the relationship with the ice adhesion results, obtained by using different ice block sizes. FINDINGS: Three different de-icing mechanisms were identified: (i) single detachment occurs when small ice blocks are considered, and the ice completely detaches in a single event. In the case of larger ice blocks, the reattachment of the ice block is promoted by either: (ii) stick-slip or, (iii) interfacial slippage, depending on the lubricant content. It was confirmed that the ice adhesion strength not only depends on material properties but also on experimental conditions, such as the ice dimensions. Moreover, differently than on hard surfaces, where wetting primarily determines the icephobic performance, also elasticity and lubrication should be considered on soft surfaces.

Withdrawn: Low ice adhesion on soft surfaces: Elasticity or lubrication effects?

This article has been withdrawn at the request of the author(s) and/or editor. The Publisher apologizes for any inconvenience this may cause. The full Elsevier Policy on Article Withdrawal can be found at https://www.elsevier.com/about/policies/article-withdrawal.

A Versatile Protein and Cell Patterning Method Suitable for Long-Term Neural Cultures.

Herein, we present an easy-to-use protein and cell patterning method relying solely on pipetting, rinsing steps and illumination with a desktop lamp, which does not require any expensive laboratory equipment, custom-built hardware or delicate chemistry. This method is based on the adhesion promoter poly(allylamine)-grafted perfluorophenyl azide, which allows UV-induced cross-linking with proteins and the antifouling molecule poly(vinylpyrrolidone). Versatility is demonstrated by creating patterns with two different proteins and a polysaccharide directly on plastic well plates and on glass slides, and by subsequently seeding primary neurons and C2C12 myoblasts on the patterns to form islands and mini-networks. Patterning characterization is done via immunohistochemistry, Congo red staining, ellipsometry, and infrared spectroscopy. Using a pragmatic setup, patterning contrasts down to 5 µm and statistically significant long-term stability superior to the gold standard poly(l-lysine)-grafted poly(ethylene glycol) could be obtained. This simple method can be used in any laboratory or even in classrooms and its outstanding stability is especially interesting for long-term cell experiments, e.g., for bottom-up neuroscience, where well-defined microislands and microcircuits of primary neurons are studied over weeks.

Comparison of the Lubricity and Surface Roughness of 5 Cosmetic Contact Lenses.

OBJECTIVES: Cosmetic contact lenses are increasingly popular because of their eye enhancing cosmetic benefits. The pigment particles used in these lenses can impact lens surface characteristics. This article examines the surface characteristics and the differences between the clear and the pigmented regions among five limbal ring design lenses. METHODS: Scanning electron microscopy was used to determine the location and depth of the pigment particles from the lens surface. The coefficient of friction (CoF) was determined with a Basalt-MUST microtribometer at clear and pigmented regions on either the front or the back surface. Atomic force microscopy was used to determine the surface roughness of each lens in root-mean-square (RMS) units at clear and pigmented regions. A linear mixed model for repeated measures was used for the analysis of the CoF and RMS roughness to compare all lenses. RESULTS: Four lens types had pigments exposed on the surface and one lens type had pigment fully enclosed. The CoF difference between clear and pigmented regions were similar and not statistically significant (P=0.0124) for the lens type with pigments enclosed, whereas the CoF difference for the other four lens types showed statistically significant difference (P<0.0001). CONCLUSIONS: Of the lenses tested here, cosmetic contact lenses with pigments enclosed in the lens matrix provided a more consistent surface between clear and pigmented regions compared with lenses that had exposed pigments.

Easy to Apply Polyoxazoline-Based Coating for Precise and Long-Term Control of Neural Patterns.

Arranging cultured cells in patterns via surface modification is a tool used by biologists to answer questions in a specific and controlled manner. In the past decade, bottom-up neuroscience emerged as a new application, which aims to get a better understanding of the brain via reverse engineering and analyzing elementary circuitry in vitro. Building well-defined neural networks is the ultimate goal. Antifouling coatings are often used to control neurite outgrowth. Because erroneous connectivity alters the entire topology and functionality of minicircuits, the requirements are demanding. Current state-of-the-art coating solutions such as widely used poly(l-lysine)-g-poly(ethylene glycol) (PLL-g-PEG) fail to prevent primary neurons from making undesired connections in long-term cultures. In this study, a new copolymer with greatly enhanced antifouling properties is developed, characterized, and evaluated for its reliability, stability, and versatility. To this end, the following components are grafted to a poly(acrylamide) (PAcrAm) backbone: hexaneamine, to support spontaneous electrostatic adsorption in buffered aqueous solutions, and propyldimethylethoxysilane, to increase the durability via covalent bonding to hydroxylated culture surfaces and antifouling polymer poly(2-methyl-2-oxazoline) (PMOXA). In an assay for neural connectivity control, the new copolymer's ability to effectively prevent unwanted neurite outgrowth is compared to the gold standard, PLL-g-PEG. Additionally, its versatility is evaluated on polystyrene, glass, and poly(dimethylsiloxane) using primary hippocampal and cortical rat neurons as well as C2C12 myoblasts, and human fibroblasts. PAcrAm-g-(PMOXA, NH2, Si) consistently outperforms PLL-g-PEG with all tested culture surfaces and cell types, and it is the first surface coating which reliably prevents arranged nodes of primary neurons from forming undesired connections over the long term. Whereas the presented work focuses on the proof of concept for the new antifouling coating to successfully and sustainably prevent unwanted connectivity, it is an important milestone for in vitro neuroscience, enabling follow-up studies to engineer neurologically relevant networks. Furthermore, because PAcrAm-g-(PMOXA, NH2, Si) can be quickly applied and used with various surfaces and cell types, it is an attractive extension to the toolbox for in vitro biology and biomedical engineering.

Reducing Friction in the Eye: A Comparative Study of Lubrication by Surface-Anchored Synthetic and Natural Ocular Mucin Analogues.

Biomaterials used in the ocular environment should exhibit specific tribological behavior to avoid discomfort and stress-induced epithelial damage during blinking. In this study, two macromolecules that are commonly employed as ocular biomaterials, namely, poly(vinylpyrrolidone) (PVP) and hyaluronan (HA), are compared with two known model glycoproteins, namely bovine submaxillary mucin (BSM) and α1-acid glycoprotein (AGP), with regard to their nonfouling efficiency, wettability, and tribological properties when freely present in the lubricant, enabling spontaneous adsorption, and when chemisorbed under low contact pressures. Chemisorbed coatings were prepared by means of photochemically triggered nitrene insertion reactions. BSM and AGP provided boundary lubrication when spontaneously adsorbed in a hydrophobic contact with a coefficient of friction (CoF) of ∼0.03-0.04. PVP and HA were found to be excellent boundary lubricants when chemisorbed (CoF ≤ 0.01). Notably, high-molecular-weight PVP generated thick adlayers, typically around 14 nm, and was able to reduce the CoF below 0.005 when slid against a BSM-coated poly(dimethylsiloxane) pin in a tearlike fluid.

Friction Measurements on Contact Lenses in a Physiologically Relevant Environment: Effect of Testing Conditions on Friction.

PURPOSE: To characterize the effect of lubricant composition and in vitro ageing on the coefficient of friction (CoF) of a wide range of commercially available soft contact lenses (SCLs). METHODS: The CoF of SCLs was characterized by means of microtribometry against a mucin-coated glass disk. One reusable (RU) silicone-hydrogel (SiHy) lens, senofilcon A, and two daily disposable (DD) lenses, etafilcon A (hydrogel) and nelfilcon A (hydrogel), were tested under different lubricant solutions, including a tear-like fluid (TLF) containing proteins and lipids. Five RU (balafilcon A [SiHy], comfilcon A [SiHy], etafilcon A [hydrogel], lotrafilcon B [SiHy], senofilcon A [SiHy]) and five DD (delefilcon A [SiHy], etafilcon A [hydrogel; two lens types], narafilcon A [SiHy], nelfilcon A [hydrogel]) lenses were tested before and after exposure to an in vitro ageing process, consisting of continuous immersion and withdrawal from TLF for 18 hours. The CoF in TLF was further compared to previously published data collected in a different lubricant. RESULTS: After in vitro ageing, three RU (balafilcon A, etafilcon A, comfilcon A) and three DD (delefilcon A, etafilcon A, nelfilcon A) lenses displayed a significant increase in CoF (P < 0.05). Lenses that contained poly (vinyl pyrrolidone; PVP) showed unaltered CoF after ageing. CONCLUSIONS: An in vitro methodology to simulate in vivo wearing of contact lenses has been proposed. The results suggest that certain lens materials show increased CoF after ageing, with potential clinical implications. The results indicate that the presence of a persistent wetting agent is of advantage to maintain a low CoF after prolonged wearing.

Imparting Nonfouling Properties to Chemically Distinct Surfaces with a Single Adsorbing Polymer: A Multimodal Binding Approach.

Surface-active polymers that display nonfouling properties and carry binding groups that can adsorb onto different substrates are highly desirable. We present a postmodification protocol of an active-ester-containing polymer that allows the creation of such a versatile platform. Poly(pentafluorophenyl acrylate) has been postmodified with a fixed grafting ratio of a nonfouling function (mPEG) and various combinations of functional groups, such as amine, silane and catechol, which can provide strong affinity to two model substrates: SiO2 and TiO2 . Adsorption, stability and resistance to nonspecific protein adsorption of the polymer films were studied. A polymer was obtained that maintained its surface functionality under a variety of harsh conditions. EG surface-density calculations show that this strategy generates a denser packing when both negatively and positively charged groups are present within the backbone, and readily allows the fabrication of a broad combinatorial matrix.

Coefficient of Friction of Human Corneal Tissue.

PURPOSE: A novel property evaluation methodology was used to determine the elusive value for the human corneal coefficient of friction (CoF). METHODS: Using a microtribometer on 28 fresh human donor corneas with intact epithelia, the CoF was determined in 4 test solutions (≥5 corneas/solution): tear-mimicking solution (TMS) in borate-buffered saline (TMS-PS), TMS in phosphate-buffered saline (TMS-PBS), TMS with HEPES-buffered saline (TMS-HEPES), and tear-like fluid in PBS (TLF-PBS). RESULTS: Mean (SD) CoF values ranged from 0.006 to 0.015 and were 0.013 (0.010) in TMS-PS, 0.006 (0.003) in TMS-PBS, 0.014 (0.005) in TMS-HEPES, and 0.015 (0.009) in TLF-PBS. Statistically significant differences were shown for TMS-PBS versus TLF (P = 0.0424) and TMS-PBS versus TMS-HEPES (P = 0.0179), but not for TMS-PBS versus TMS-PS (P = 0.2389). CONCLUSIONS: Successful measurement of the fresh human corneal tissue CoF was demonstrated, with values differing in the evaluated buffer solutions, within this limited sample size.

Spontaneous Blinking from a Tribological Viewpoint.

The mechanical forces between the lid wiper and the ocular surface, and between a contact lens and the lid wiper, are reported to be related to dry eye symptoms. Furthermore, the mechanical forces between these sliding partners are assumed to be related to the ocular signs of lid-wiper epitheliopathy (LWE) and lid-parallel conjunctival folds (LIPCOF). Recent literature provides some evidence that a contact lens with a low coefficient of friction (CoF) improves wearing comfort by reducing the mechanical forces between the contact lens surface and the lid wiper. This review discusses the mechanical forces during spontaneous blinks from a tribological perspective, at both low and high sliding velocities, in a healthy subject. It concludes that the coefficient of friction of the ocular surfaces appears to be strongly comparable to that of hydrophilic polymer brushes at low sliding velocity, and that, with increased sliding velocity, there is no wear at the sliding partners' surfaces thanks to the presence of a fluid film between the two sliding partners. In contrast, in the case of dry eye, the failure to maintain a full fluid film lubrication regime at high blinking speeds may lead to increased shear rates, resulting in deformation and wear of the sliding pairs. These shear rates are most likely related to tear film viscosity.

Delineating fibronectin bioadhesive micropatterns by photochemical immobilization of polystyrene and poly(vinylpyrrolidone).

Bioadhesive micropatterns, capable of laterally confining cells to a 2D lattice, have proven effective in simulating the in vivo tissue environment. They reveal fundamental aspects of the role of adhesion in cell mechanics, proliferation, and differentiation. Here we present an approach based on photochemistry for the fabrication of synthetic polymer micropatterns. Perfluorophenyl azide (PFPA), upon deep-UV exposure, forms a reactive nitrene capable of covalently linking to a molecule that is in close proximity. PFPA has been grafted onto a backbone of poly(allyl amine), which readily forms a self-assembled monolayer on silicon wafers or glass. A film of polystyrene was applied by spin-coating, and by laterally confining the UV exposure through a chromium-on-quartz photomask, monolayers of polymers could be immobilized in circular microdomains. Poly(vinylpyrrolidone) (PVP) was attached to the background to form a barrier to nonspecific protein adsorption and cell adhesion. Micropatterns were characterized with high-lateral-resolution time-of-flight secondary ion mass spectrometry (TOF-SIMS), which confirmed the formation of polystyrene domains within a PVP background. Fluorescence-microscopy adsorption assays with rhodamine-labeled bovine serum albumin demonstrated the nonfouling efficiency of PVP and, combined with TOF-SIMS, allowed for a comprehensive characterization of the pattern geometry. The applicability of the micropatterned platform in single-cell assays was tested by culturing two cell types, WM 239 melanoma cells and SaOs-2 osteoblasts, on micropatterned glass, either with or without backfilling of the patterns with fibronectin. It was demonstrated that the platform was efficient in confining cells to the fibronectin-backfilled micropatterns for at least 48 h. PVP is thus proposed as a viable, highly stable alternative to poly(ethylene glycol) for nonfouling applications. Due to the versatility of the nitrene-insertion reaction, the platform could be extended to other polymer pairs or proteins and the surface chemistry adapted to specific applications.

Photochemically prepared, two-component polymer-concentration gradients.

A versatile, photochemical surface-modification approach using nitrene-insertion reactions has been employed to develop an ultrathin, two-component, polymer-gradient coating. Perfluorophenyl azide (PFPA) acted as the photosensitive moiety, forming a nitrene radical upon 254 nm UV exposure. Cationic poly(allyl amine) was grafted with PFPA and surface-anchored onto silicon wafers by means of electrostatic self-assembly. After spin-coating of polystyrene (PS), the substrate was illuminated from behind a moving shutter, thereby controlling the azide-to-nitrene conversion degree across the substrate, and leading to a gradually varying PS density after rinsing. Backfilling with poly(vinyl pyrrolidone) (PVP) and re-exposing to UV light formed a two-component polymer-density gradient. The composition varied linearly following exposure to a linear UV exposure profile, as determined with spectroscopic ellipsometry (ELM) and X-ray photoelectron spectroscopy (XPS). High-spatial-resolution, time-of-flight secondary ion mass spectrometry (ToF-SIMS) revealed a high degree of mixing between the two incompatible polymers on the micrometer scale. The dynamic water-contact angle (dCA) was found to depend strongly on the sample history, suggesting adaptive properties of the coating, which was further confirmed by angle-resolved XPS (ARXPS). To confirm the applicability of the system for biological investigations, gradients were exposed to zoospores of the macrofouling alga Ulva linza , and a critical PS composition of 70% was identified, above which settlement started to increase. It has been shown that a two-component polymer-density gradient can provide a high-throughput platform for determining critical surface properties of polymer blend materials.

Evaluation of chemically modified SLA implants (modSLA) biofunctionalized with integrin (RGD)- and heparin (KRSR)-binding peptides.

Enhancing osseointegration through surface immobilization of multiple short peptide sequences that mimic extracellular matrix (ECM) proteins, such as arginine-glycine-aspartic acid (RGD) and lysine-arginine-serine-arginine (KRSR), has not yet been extensively explored. Additionally, the effect of biofunctionalizing chemically modified sandblasted and acid-etched surfaces (modSLA) is unknown. The present study evaluated modSLA implant surfaces modified with RGD and KRSR for potentially enhanced effects on bone apposition and interfacial shear strength during early stages of bone regeneration. Two sets of experimental implants were placed in the maxillae of eight miniature pigs, known for their rapid wound healing kinetics: bone chamber implants creating two circular bone defects for histomorphometric analysis on one side and standard thread configuration implants for removal torque testing on the other side. Three different biofunctionalized modSLA surfaces using poly-L-lysine-graft-poly(ethylene glycol) (PLL-g-PEG) as a carrier minimizing nonspecific protein adsorption [(i) 20 pmol cm⁻² KRSR alone (KRSR); or in combination with RGD in two different concentrations; (ii) 0.05 pmol cm⁻² RGD (KRSR/RGD-1); (iii) 1.26 pmol cm⁻² RGD (KRSR/RGD-2)] were compared with (iv) control modSLA. Animals were sacrificed at 2 weeks. Removal torque values (701.48-780.28 N mm), bone-to-implant contact (BIC) (35.22%-41.49%), and new bone fill (28.58%-30.62%) demonstrated no significant differences among treatments. It may be concluded that biofunctionalizing modSLA surfaces with KRSR and RGD derivatives of PLL-g-PEG polymer does not increase BIC, bone fill, or interfacial shear strength.

Poly(ethylene glycol) and hydroxy functionalized alkane phosphate self-assembled monolayers reduce bacterial adhesion and support osteoblast proliferation.

PURPOSE: Presently there is interest today in designing improved titanium surfaces capable of high bioactivity in order to promote strong anchorage of the bone surrounding implants while at the same time discouraging bioadhesion. Poly(ethylene glycol)-modified (PEG) alkane phosphate and OH-terminated alkane phosphates have been demonstrated to be spontaneously adsorbed onto titanium oxide surfaces and produce surfaces with different protein resistance in relation to the PEG surface density. This study aims to evaluate caries-associated Streptococcus mutans (S. mutans) adhesion and osteoblast proliferation while varying the PEG surface density of titanium surfaces. METHODS: Bacterial adhesion was quantified by fluorescence microscopy and SAOS-2 human osteoblast proliferation was evaluated up to 7 days of culture in vitro. Metabolic activity of osteoblasts was measured by MTT test and the secretion of extracellular matrix proteins (osteopontin, osteocalcin and type I collagen) in culture medium was determined by immunoenzymatic assays. RESULTS: As the PEG surface density increased, the bacterial adhesion considerably decreased when compared to uncoated titanium surfaces. The monomolecular coatings proved to be capable of supporting osteoblast proliferation with the greatest levels of metabolic activity at the highest PEG surface concentrations. CONCLUSIONS: These results are extremely promising for potential clinical application in implant uses where both reduction of bacteria adhesion and stimulation of bone formation are highly desirable.

Enhanced osteoblastic activity and bone regeneration using surface-modified porous bioactive glass scaffolds.

The potential use as a bone substitute material of a three-dimensional bioactive glass fiber scaffold composed of Na(2)O-K(2)O-MgO-CaO-B(2)O(3)-P(2)O(5)-SiO(2) (BG1) was investigated in this work. Scaffolds were pre-treated with simulated body fluid (SBF) to promote the formation of two different bone-like apatite layers on their surfaces. The topography and roughness of the deposited layers were assessed by scanning electron microscopy (SEM), while the chemical composition and structure using X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy, respectively. Based on surface analysis, the bioactive glass surfaces were ranked from smoothest to roughest: 0 SBF (untreated), 1x SBF and 2x SBF. A calcium-deficient carbonated hydroxyapatite (HCA) layer was present on both SBF-treated scaffolds, with higher number and larger bone-like apatite nodule formation in the 2x SBF case. MC3T3-E1 preosteoblasts showed a more flattened morphology and higher cell proliferation on the nontreated scaffolds; whereas, cells were more elongated and had higher osteoblastic activity on SBF-treated samples. In vivo results in a rabbit calvarial bone defect model showed enhanced bone formation with SBF pretreated scaffolds, compared with untreated ones, commercially available Perioglass particles and empty defects. Our findings demonstrate that the formation of a rough HCA layer on bioactive glass porous scaffolds enhanced preosteoblast maturation in vitro, as well as bone formation in vivo.

Fabricating chemical gradients on oxide surfaces by means of fluorinated, catechol-based, self-assembled monolayers.

Catechols bind strongly to several metal oxides and can thus be used as a binding group for generating self-assembled monolayers. Furthermore, their derivatives can be used to produce well-defined, centimeter-scale surface-chemical gradients on technologically relevant surfaces, such as titanium dioxide (TiO(2)). A simple dip-and-rinse gradient-preparation technique was utilized to produce surface-hydrophobicity gradients from perfluoro-alkyl catechols and nitrodopamine (ND). Chemical composition, quality, and properties of the functionalized surfaces were determined by means of X-ray photoelectron spectroscopy (XPS), variable-angle spectroscopic ellipsometry (VASE), and static water contact angle (sCA) measurements. Contact angles were found to be in the range of 30°-95°, correlating well with the determined surface chemical composition and adlayer thickness.

Poly(ethylene glycol) adlayers immobilized to metal oxide substrates through catechol derivatives: influence of assembly conditions on formation and stability.

We have investigated five different poly(ethylene glycol) (PEG, 5 kDa) catechol derivatives in terms of their spontaneous surface assembly from aqueous solution, adlayer stability, and resistance to nonspecific blood serum adsorption as a function of the type of catechol-based anchor, assembly conditions (temperature, pH), and type of substrate (SiO(2), TiO(2), Nb(2)O(5)). Variable-angle spectroscopic ellipsometry (VASE) was used for layer thickness evaluation, X-ray photoelectron spectroscopy (XPS) for layer composition, and ultraviolet-visible optical spectroscopy (UV-vis) for cloud point determination. Polymer surface coverage was influenced by the type of catechol anchor, type of the substrate, as well as pH and temperature (T) of the assembly solution. Furthermore, it was found to be highest for T close to the cloud point (T(CP)) and pH of the assembly solution close to pK(a1) (dissociation constant of the first catechol hydroxy group) of the polymer and to the isoelectric point (IEP) of the substrate. T(CP) turned out to depend on not only the ionic strength of the assembly solution, but also the type of catechol derivative and pH. PEG-coating dry thickness above 10 A correlated with low serum adsorption. We therefore conclude that optimum coating protocols for catechol-based polymer assembly at metal oxide interfaces have to take into account specific physicochemical properties of the polymer, anchor, and substrate.

Poly(ethylene glycol) and hydroxy functionalized alkane phosphate mixed self-assembled monolayers to control nonspecific adsorption of proteins on titanium oxide surfaces.

The spontaneous formation of alkane phosphate self-assembled monolayers (SAMs) on titanium oxide was chosen as a tool to tailor the surface physicochemical properties in terms of nonspecific adsorption of proteins. For this aim, poly(ethylene glycol)-modified (PEG) alkane phosphate was codeposited with OH-terminated alkane phosphates. X-ray photoelectron spectroscopy and ellipsometry of the resulting mixed SAMs indicate that the PEG density can be controlled by varying the mole fraction of PEG-terminated phosphates in the solutions used during the deposition process, leading to surfaces with different degrees of protein resistance.

Self-assembly of poly(ethylene glycol)-poly(alkyl phosphonate) terpolymers on titanium oxide surfaces: synthesis, interface characterization, investigation of nonfouling properties, and long-term stability.

This contribution deals with the self-assembling of a terpolymer on titanium oxide (TiO(2)) surface. The polymer structure was obtained by polymerization of different methacrylates, i.e., alkyl-phosphonated, butyl and PEG methacrylate, in the presence of a chain transfer agent. The resulting PEG-poly(alkyl phosphonate) material, characterized mainly by SEC and NMR, self-organized at the interface of TiO(2). AR-XPS demonstrated the binding of phosphonate groups to TiO(2) substrate and the formation of a PEG-brush layer at the outermost part of the system. The stability of this terpolymer adlayer, after exposure to solutions of pH 2, 7.4, and 9 up to 3 weeks, was evaluated quantitatively by XPS and ellipsometry. We demonstrated an overall stability improvements of this coating against desorption in contact with aqueous solutions in comparison with reference self-assembly systems. Finally, the PEG-terpolymer adlayer proved to impart to TiO(2) substrate antifouling properties when exposed to full blood serum.

Comparison of the response of cultured osteoblasts and osteoblasts outgrown from rat calvarial bone chips to nonfouling KRSR and FHRRIKA-peptide modified rough titanium surfaces.

Mimicking proteins found in the extracellular matrix (ECM) using specific peptide sequences is a well-known strategy for the design of biomimetic surfaces, but has not yet been widely exploited in the field of biomedical implants. This study investigated osteoblast and, as a control, fibroblast proliferation to novel consensus heparin-binding peptides sequences KRSR and FHRIKKA that were immobilized onto rough (particle-blasted and chemically etched) commercially pure titanium surfaces using a poly(L-lysine)-graft-poly(ethylene glycol) (PLL-g-PEG) molecular assembly system. This platform enabled a detailed study of specific cell-peptide interactions even in the presence of serum in the culture medium; thanks to the excellent nonfouling properties of the PLL-g-PEG surface. Cell-binding peptide sequence RGD in combination with KRSR or FHRRIKA was used to examine a potentially-enhanced or synergistic effect on osteoblast proliferation. Bare titanium and bioinactive surfaces (i.e., unfunctionalized PLL-g-PEG and scrambled KSSR, RFHARIK, and RDG) were used as control substrates. Additionally, in a newly developed experimental setup, freshly harvested bone chips from newborn rat calvariae were placed onto the same type of surfaces investigating size and pattern of osteoblast outgrowths. The findings of the current study demonstrated that the difference in osteoblast and fibroblast proliferation was influenced by surface topography more so than by the presence of surface-bound KRSR and FHRRIKA. On the other hand, in comparison with the control surfaces, osteoblast outgrowths from rat calvarial bone chips covered a significantly larger area on RGD, KRSR, and FHRRIKA surfaces after 8 days and also migrated in an isotropic way unlike cells on the bioinactive substrates. Furthermore, the stimulatory effect of 0.75 pmol cm(-2) RGD on osteoblast migration pattern could be enhanced when applied in combination with 2.25 pmol cm(-2) KRSR.