Stability of influenza A virus in droplets and aerosols is heightened by the presence of commensal respiratory bacteria.

Aerosol transmission remains a major challenge for control of respiratory viruses, particularly those causing recurrent epidemics, like influenza A virus (IAV). These viruses are rarely expelled alone, but instead are embedded in a consortium of microorganisms that populate the respiratory tract. The impact of microbial communities and inter-pathogen interactions upon stability of transmitted viruses is well-characterized for enteric pathogens, but is under-studied in the respiratory niche. Here, we assessed whether the presence of five different species of commensal respiratory bacteria could influence the persistence of IAV within phosphate-buffered saline and artificial saliva droplets deposited on surfaces at typical indoor air humidity, and within airborne aerosol particles. In droplets, presence of individual species or a mixed bacterial community resulted in 10- to 100-fold more infectious IAV remaining after 1 h, due to bacterial-mediated flattening of drying droplets and early efflorescence. Even when no efflorescence occurred at high humidity or the bacteria-induced changes in droplet morphology were abolished by aerosolization instead of deposition on a well plate, the bacteria remained protective. Staphylococcus aureus and Streptococcus pneumoniae were the most stabilizing compared to other commensals at equivalent density, indicating the composition of an individual's respiratory microbiota is a previously unconsidered factor influencing expelled virus persistence.IMPORTANCEIt is known that respiratory infections such as coronavirus disease 2019 and influenza are transmitted by release of virus-containing aerosols and larger droplets by an infected host. The survival time of viruses expelled into the environment can vary depending on temperature, room air humidity, UV exposure, air composition, and suspending fluid. However, few studies consider the fact that respiratory viruses are not alone in the respiratory tract-we are constantly colonized by a plethora of bacteria in our noses, mouth, and lower respiratory system. In the gut, enteric viruses are known to be stabilized against inactivation and environmental decay by gut bacteria. Despite the presence of a similarly complex bacterial microbiota in the respiratory tract, few studies have investigated whether viral stabilization could occur in this niche. Here, we address this question by investigating influenza A virus stabilization by a range of commensal bacteria in systems representing respiratory aerosols and droplets.

Phenotypic resistant single-cell characteristics under recurring ampicillin antibiotic exposure in Escherichia coli.

Non-heritable, phenotypic drug resistance toward antibiotics challenges antibiotic therapies. Characteristics of such phenotypic resistance have implications for the evolution of heritable resistance. Diverse forms of phenotypic resistance have been described, but phenotypic resistance characteristics remain less explored than genetic resistance. Here, we add novel combinations of single-cell characteristics of phenotypic resistant E. coli cells and compare those to characteristics of susceptible cells of the parental population by exposure to different levels of recurrent ampicillin antibiotic. Contrasting expectations, we did not find commonly described characteristics of phenotypic resistant cells that arrest growth or near growth. We find that under ampicillin exposure, phenotypic resistant cells reduced their growth rate by about 50% compared to growth rates prior to antibiotic exposure. The growth reduction is a delayed alteration to antibiotic exposure, suggesting an induced response and not a stochastic switch or caused by a predetermined state as frequently described. Phenotypic resistant cells exhibiting constant slowed growth survived best under ampicillin exposure and, contrary to expectations, not only fast-growing cells suffered high mortality triggered by ampicillin but also growth-arrested cells. Our findings support diverse modes of phenotypic resistance, and we revealed resistant cell characteristics that have been associated with enhanced genetically fixed resistance evolution, which supports claims of an underappreciated role of phenotypic resistant cells toward genetic resistance evolution. A better understanding of phenotypic resistance will benefit combatting genetic resistance by developing and engulfing effective anti-phenotypic resistance strategies. IMPORTANCE: Antibiotic resistance is a major challenge for modern medicine. Aside from genetic resistance to antibiotics, phenotypic resistance that is not heritable might play a crucial role for the evolution of antibiotic resistance. Using a highly controlled microfluidic system, we characterize single cells under recurrent exposure to antibiotics. Fluctuating antibiotic exposure is likely experienced under common antibiotic therapies. These phenotypic resistant cell characteristics differ from previously described phenotypic resistance, highlighting the diversity of modes of resistance. The phenotypic characteristics of resistant cells we identify also imply that such cells might provide a stepping stone toward genetic resistance, thereby causing treatment failure.

3D-printed digital pneumatic logic for the control of soft robotic actuators.

Soft robots are paving their way to catch up with the application range of metal-based machines and to occupy fields that are challenging for traditional machines. Pneumatic actuators play an important role in this development, allowing the construction of bioinspired motion systems. Pneumatic logic gates provide a powerful alternative for controlling pressure-activated soft robots, which are often controlled by metallic valves and electric circuits. Many existing approaches for fully compliant pneumatic control logic suffer from high manual effort and low pressure tolerance. In our work, we invented three-dimensional (3D) printable, pneumatic logic gates that perform Boolean operations and imitate electric circuits. Within 7 hours, a filament printer is able to produce a module that serves as an OR, AND, or NOT gate; the logic function is defined by the assigned input signals. The gate contains two alternately acting pneumatic valves, whose work principle is based on the interaction of pressurized chambers and a 3D-printed 1-millimeter tube inside. The gate design does not require any kind of support material for its hollow parts, which makes the modules ready to use directly after printing. Depending on the chosen material, the modules can operate on a pressure supply between 80 and more than 750 kilopascals. The capabilities of the invented gates were verified by implementing an electronics-free drink dispenser based on a pneumatic ring oscillator and a 1-bit memory. Their high compliance is demonstrated by driving a car over a fully flexible, 3D-printed robotic walker controlled by an integrated circuit.