Harvest Initiated Volatile Organic Compound Emissions from In-Field Tall Wheatgrass.

While crop and grassland usage continues to increase, the full diversity of plant-specific volatile organic compounds (VOCs) emitted from these ecosystems, including their implications for atmospheric chemistry and carbon cycling, remains poorly understood. It is particularly important to investigate VOCs in the context of potential biofuels: aside from the implications of large-scale land use, harvest may shift both the flux and speciation of emitted VOCs. To this point, we evaluate the diversity of VOCs emitted both pre and postharvest from "Alkar" tall wheatgrass (Thinopyrum ponticum), a candidate biofuel that exhibits greater tolerance to frost and saline land compared to other grass varieties. Mature plants grown under field conditions (n = 6) were sampled for VOCs both pre- and postharvest (October 2022). Via hierarchical clustering of emitted VOCs from each plant, we observe distinct "volatilomes" (diversity of VOCs) specific to the pre- and postharvest conditions despite plant-to-plant variability. In total, 50 VOCs were found to be unique to the postharvest tall wheatgrass volatilome, and these unique VOCs constituted a significant portion (26%) of total postharvest signal. While green leaf volatiles (GLVs) dominate the speciation of postharvest emissions (e.g., 54% of unique postharvest VOC signal was due to 1-penten-3-ol), we demonstrate novel postharvest VOCs from tall wheatgrass that are under characterized in the context of carbon cycling and atmospheric chemistry (e.g., 3-octanone). Continuing evaluations will quantitatively investigate tall wheatgrass VOC fluxes, better informing the feasibility and environmental impact of tall wheatgrass as a biofuel.

Experimental and Computational Evaluation of Lipidomic In-Source Fragmentation as a Result of Postionization with Matrix-Assisted Laser Desorption/Ionization.

Matrix-assisted laser desorption/ionization mass spectrometry imaging (MALDI-MSI) can provide spatially resolved molecular information about a sample. Recently, a postionization approach (MALDI-2) has been commercially integrated with MALDI-MSI, allowing for bettered sensitivity and consequent improved spatial resolution. While advantages of MALDI-2 have previously been established, we demonstrate here statistically increased in-source fragmentation (ISF) results from postionization with a commercial instrument. Via lipid standard analyses, known MALDI ISF pathways (e.g., loss of trimethylamine) were statistically increased in MALDI-2 compared to MALDI-1 (65-172% increase in fragmentation). Gas phase molecular modeling with density functional theory estimated that the most-weighted virtual orbitals to excite within lipids involve ester and phosphate bonds. Protonated lipid excitation energies are furthermore red-shifted compared to those of other adduct types [e.g., 254 nm for protonated PC(16:0/18:1)] and approach the MALDI-2 laser energy (266 nm). Analysis of rat brain homogenate detected statistically more positive-ion mode peaks with MALDI-2 (1090) than that with MALDI-1 (719), where Kernel density estimations showed that the majority of this enhancement occurs with low m/z ions (i.e., m/z 75-500). Taken together with the lipid standard data, these observations may indicate ISF due to postionization. While artifact contributions from matrix blanks were also noted, both experimental and computational data sets suggest that the overall extent of ISF is statistically increased in MALDI-2 compared to MALDI-1.

Tethered balloon system and High-Resolution Mass Spectrometry Reveal Increased Organonitrates Aloft Compared to the Ground Level.

Atmospheric particles play critical roles in climate. However, significant knowledge gaps remain regarding the vertically resolved organic molecular-level composition of atmospheric particles due to aloft sampling challenges. To address this, we use a tethered balloon system at the Southern Great Plains Observatory and high-resolution mass spectrometry to, respectively, collect and characterize organic molecular formulas (MF) in the ground level and aloft (up to 750 m) samples. We show that organic MF uniquely detected aloft were dominated by organonitrates (139 MF; 54% of all uniquely detected aloft MF). Organonitrates that were uniquely detected aloft featured elevated O/C ratios (0.73 ± 0.23) compared to aloft organonitrates that were commonly observed at the ground level (0.63 ± 0.22). Unique aloft organic molecular composition was positively associated with increased cloud coverage, increased aloft relative humidity (∼40% increase compared to ground level), and decreased vertical wind variance. Furthermore, 29% of extremely low volatility organic compounds in the aloft sample were truly unique to the aloft sample compared to the ground level, emphasizing potential oligomer formation at higher altitudes. Overall, this study highlights the importance of considering vertically resolved organic molecular composition (particularly for organonitrates) and hypothesizes that aqueous phase transformations and vertical wind variance may be key variables affecting the molecular composition of aloft organic aerosol.

Alkylperoxy radicals are responsible for the formation of oxygenated primary organic aerosol.

Organic aerosol (OA) is an air pollutant ubiquitous in urban atmospheres. Urban OA is usually apportioned into primary OA (POA), mostly emitted by mobile sources, and secondary OA (SOA), which forms in the atmosphere due to oxidation of gas-phase precursors from anthropogenic and biogenic sources. By performing coordinated measurements in the particle phase and the gas phase, we show that the alkylperoxy radical chemistry that is responsible for low-temperature ignition also leads to the formation of oxygenated POA (OxyPOA). OxyPOA is distinct from POA emitted during high-temperature ignition and is chemically similar to SOA. We present evidence for the prevalence of OxyPOA in emissions of a spark-ignition engine and a next-generation advanced compression-ignition engine, highlighting the importance of understanding OxyPOA for predicting urban air pollution patterns in current and future atmospheres.

Fungal organic acid uptake of mineral-derived K is dependent on distance from carbon hotspot.

IMPORTANCE: Fungal species are foundational members of soil ecosystems with vital contributions that support interspecies resource translocation. The minute details of these biogeochemical processes are poorly investigated. Here, we addressed this knowledge gap by probing fungal growth in a novel mineral-doped soil micromodel platform using spatially-resolved imaging methodologies. We found that fungi uptake K from K-rich minerals using organic acids exuded in a distance-dependent manner from a carbon-rich hotspot. While identification of specific mechanisms within soil remains challenging, our findings demonstrate the significance of reduced complexity platforms such as the mineral-doped micromodel in probing biogeochemical processes. These findings provide visualization into hyphal uptake and transport of mineral-derived nutrients in a resource-limited environment.

Nonequilibrium Behavior in Isoprene Secondary Organic Aerosol.

Recent studies have shown that instantaneous gas-particle equilibrium partitioning assumptions fail to predict SOA formation, even at high relative humidity (∼85%), and photochemical aging seems to be one driving factor. In this study, we probe the minimum aging time scale required to observe nonequilibrium partitioning of semivolatile organic compounds (SVOCs) between the gas and aerosol phase at ∼50% RH. Seed isoprene SOA is generated by photo-oxidation in the presence of effloresced ammonium sulfate seeds at <1 ppbv NOx, aged photochemically or in the dark for 0.3-6 h, and subsequently exposed to fresh isoprene SVOCs. Our results show that the equilibrium partitioning assumption is accurate for fresh isoprene SOA but breaks down after isoprene SOA has been aged for as short as 20 min even in the dark. Modeling results show that a semisolid SOA phase state is necessary to reproduce the observed particle size distribution evolution. The observed nonequilibrium partitioning behavior and inferred semisolid phase state are corroborated by offline mass spectrometric analysis on the bulk aerosol particles showing the formation of organosulfates and oligomers. The unexpected short time scale for the phase transition within isoprene SOA has important implications for the growth of atmospheric ultrafine particles to climate-relevant sizes.

Experimental Assessment of Mammalian Lipidome Complexity Using Multimodal 21 T FTICR Mass Spectrometry Imaging.

Herein, we assess the complementarity and complexity of data that can be detected within mammalian lipidome mass spectrometry imaging (MSI) via matrix-assisted laser desorption ionization (MALDI) and nanospray desorption electrospray ionization (nano-DESI). We do so by employing 21 T Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS) with absorption mode FT processing in both cases, allowing unmatched mass resolving power per unit time (≥613k at m/z 760, 1.536 s transients). While our results demonstrated that molecular coverage and dynamic range capabilities were greater in MALDI analysis, nano-DESI provided superior mass error, and all annotations for both modes had sub-ppm error. Taken together, these experiments highlight the coverage of 1676 lipids and serve as a functional guide for expected lipidome complexity within nano-DESI-MSI and MALDI-MSI. To further assess the lipidome complexity, mass splits (i.e., the difference in mass between neighboring peaks) within single pixels were collated across all pixels from each respective MSI experiment. The spatial localization of these mass splits was powerful in informing whether the observed mass splits were biological or artificial (e.g., matrix related). Mass splits down to 2.4 mDa were observed (i.e., sodium adduct ambiguity) in each experiment, and both modalities highlighted comparable degrees of lipidome complexity. Further, we highlight the persistence of certain mass splits (e.g., 8.9 mDa; double bond ambiguity) independent of ionization biases. We also evaluate the need for ultrahigh mass resolving power for mass splits ≤4.6 mDa (potassium adduct ambiguity) at m/z > 1000, which may only be resolved by advanced FTICR-MS instrumentation.

Monitoring microplastic-contaminant sorption processes in real-time using membrane introduction mass spectrometry.

Microplastics are environmentally ubiquitous and their role in the fate and distribution of trace contaminants is of emerging concern. We report the first use of membrane introduction mass spectrometry to directly monitor the rate and extent of microplastic-contaminant sorption. Target contaminant (naphthalene, anthracene, pyrene, and nonylphenol) sorption behaviours were examined at nanomolar concentrations with four plastic types: low density polyethylene (LDPE), high density polyethylene (HDPE), polypropylene (PP), and polystyrene (PS). Under the conditions employed here, short-term sorption kinetics were assessed using on-line mass spectrometry for up to one hour. Subsequent sorption was followed by periodically measuring contaminant concentrations for up to three weeks. Short-term sorption followed first order kinetics with rate constants that scaled with hydrophobicity for the homologous series of polycyclic aromatic hydrocarbons (PAHs). Sorption rate constants on LDPE for equimolar solutions of naphthalene, anthracene, and pyrene were 0.5, 2.0, and 2.2 h-1, respectively, while nonylphenol did not sorb to pristine plastics over this time period. Similar trends among contaminants were observed for other pristine plastics with 4- to 10-fold faster sorption rates associated with LDPE when compared to PS and PP. Sorption was largely complete after three weeks, with the percent analyte sorbed ranging from 40-100% across various microplastic-contaminant combinations. Photo-oxidative ageing of LDPE had little effect on PAH sorption. However, a marked increase in nonylphenol sorption was consistent with increased hydrogen-bonding interactions. This work provides kinetic insights into surface interactions and describes a powerful experimental platform to directly observe contaminant sorption behaviours in complex samples under a variety of environmentally relevant conditions.

Imaging and Direct Sampling Capabilities of Nanospray Desorption Electrospray Ionization with Absorption-Mode 21 Tesla Fourier Transform Ion Cyclotron Resonance Mass Spectrometry.

Nanospray desorption electrospray ionization mass spectrometry, a powerful ambient sampling and imaging technique, is herein coupled as an isolated source with 21 Tesla (21T) Fourier transform ion cyclotron resonance mass spectrometry (FTICR MS). Absorption-mode data, enabled by an external data acquisition system, is applied for improved mass resolution, accuracy, and dynamic range without compromising spectral acquisition rates. Isotopic fine structure (IFS) information is obtained from the ambient sampling of living Bacillus and Fusarium species, allowing for high confidence in molecular annotations with a resolution >830 k (at m/z 825). Tandem mass spectrometry experiments for biological samples are shown to retain the IFS in addition to gained fragmentation information, providing a further degree of annotation confidence from ambient analyses. Rat brain was imaged by nanospray desorption electrospray ionization (nano-DESI) 21T FTICR MS in ∼5 h using 768 ms transients, producing over 800 molecular annotations using the METASPACE platform and low-parts-per-billion mass accuracy at a spatial resolution of ∼25 × 180 µm. Finally, nano-DESI 21T FTICR MS imaging is demonstrated to reveal images corresponding to the IFS, as well as hundreds of additional molecular features (including demonstrated differences as low as 8.96 mDa) that are otherwise undetected by a more conventional imaging methodology.

A new quantitative drug checking technology for harm reduction: Pilot study in Vancouver, Canada using paper spray mass spectrometry.

INTRODUCTION: Drug checking services for harm reduction and overdose prevention have been implemented in many jurisdictions as a public health intervention in response to the opioid overdose crisis. This study demonstrates the first on-site use of paper spray mass spectrometry for quantitative drug checking to address the limitations of current on-site drug testing technologies. METHODS: Paper spray mass spectrometry was used to provide on-site drug checking services at a supervised consumption site in the Downtown Eastside of Vancouver, British Columbia, Canada during a 2-day pilot test in August 2019. The method included the targeted quantitative measurement of 49 drugs and an untargeted full scan to assist in identifying unknown/unexpected components. RESULTS: During the pilot, 113 samples were submitted for analysis, with 88 (78%) containing the client expected substance. Fentanyl was detected in 45 of 59 expected fentanyl samples, and in 50 (44%) samples overall at a median concentration of 3.6% (w/w%). The synthetic precursor of fentanyl, 4-anilino-N-phenethyl-piperidine (4-ANPP), was found in 74.0% of all fentanyl samples at a median concentration of 2.2%, suggesting widespread poor manufacturing practices. Etizolam was detected in 10 submitted samples anticipated to be fentanyl at a median concentration of 2.5%. No clients submitting these samples expected etizolam or a benzodiazepine in their sample. In three instances, it was co-measured with fentanyl, and in seven cases it was detected alone. DISCUSSION AND CONCLUSIONS: The quantitative capabilities and low detection limits demonstrated by paper spray mass spectrometry offer distinct benefits over existing on-site drug checking methods and harm reduction services.

Direct mass spectrometric analysis of naphthenic acids and polycyclic aromatic hydrocarbons in waters impacted by diluted bitumen and conventional crude oil.

Crude oil spills have well-documented, deleterious impacts on the hydrosphere. In addition to macroscopic effects on wildlife and waterscapes, several classes of petroleum derived compounds, such as naphthenic acids (NAs) and polycyclic aromatic hydrocarbons (PAHs), may be released into the water and present aquatic contamination hazards. The concentrations of these contaminants may be affected by both oil type and water chemistry. We characterize the concentrations of NAs and PAHs in natural and constructed waters, spanning a range of pH and salinity, and directly compare the influence of diluted bitumen (DB) and conventional crude (CC) oil, using condensed-phase membrane introduction mass spectrometry (CP-MIMS) as a direct sampling, on-line technique. The concentration and isomer class profiles of classical NAs in the aqueous phase were assessed using electrospray ionization in negative-ion mode as [M-H]- whereas PAH concentrations were monitored using liquid electron ionization (LEI) in positive-ion mode as [M+•]. NA concentrations (0.03-25 ppm) were highly pH-dependent, and an order of magnitude greater in water samples contaminated with DB than CC. Conversely, concentrations of naphthalene (10-130 ppb) and alkyl-naphthalenes (10-90 ppb) were three to four-fold higher in water samples exposed to CC. We demonstrate that naturally occurring dissolved organic matter does not bias results from the membrane sampling approach employed, and that DB and CC contaminated waters can be differentiated using principal component analysis of the NA isomer class distribution in both constructed and natural waters. Finally, we describe the first demonstration of the concurrent analysis of trace NAs and PAHs in the same water sample by controlling perm-selectivity at the membrane and the ionization mode of the mass spectrometer. The techniques employed here for trace analysis of petroleum derived compounds in water can be applied to rapid screening and real-time monitoring of contamination and remediation processes.

Direct, Isomer-Specific Quantitation of Polycyclic Aromatic Hydrocarbons in Soils Using Membrane Introduction Mass Spectrometry and Chemical Ionization.

Polycyclic aromatic hydrocarbons (PAHs) are routinely screened for in soils, where quantitation of structural isomers is critical due to varying toxicity within PAH isomer classes. While chromatographic methods provide isomer resolution, such strategies are cost and time intensive. To address these challenges, we present condensed phase membrane introduction mass spectrometry using liquid electron ionization/chemical ionization (CP-MIMS-LEI/CI) as a direct mass spectrometry technique that provides rapid, quantitative results for PAH isomer measurements in soil samples. A methanol acceptor phase is flowed through a probe-mounted polydimethylsiloxane hollow fiber membrane directly immersed into a dichloromethane/soil slurry. PAHs and dichloromethane co-permeate the membrane into the acceptor solvent, whereas particulates and charged matrix components remain in the sample. A nanoflow of the membrane permeate is then directly infused into a LEI/CI interfaced triple quadrupole mass spectrometer. Diagnostic PAH adduct ions were formed at either M + 45 ([M + CH2Cl + CH3OH-HCl]+) or M + 47 ([M + CHCl2-HCl]+). This allowed the development of specific MS/MS transitions for individual PAH isomers. These transitions were subsequently used for the direct analyses of PAHs in real soils where CP-MIMS-LEI/CI was shown to be rapid (15 soil samples/h) and sensitive (ng/g level detection limits). CP-MIMS-LEI/CI results compared well to those obtained using GC-MS (average percent difference of -9% across 9 PAHs in 8 soil samples), presenting a compelling argument for direct, quantitative screening of PAHs in soils by CP-MIMS-LEI/CI, particularly given the simple workflow and short analytical duty cycle.

Condensed Phase Membrane Introduction Mass Spectrometry with In Situ Liquid Reagent Chemical Ionization in a Liquid Electron Ionization Source (CP-MIMS-LEI/CI).

Direct mass spectrometry has grown significantly due to wide applicability, relative ease of use, and high sample throughput. However, many current direct mass spectrometry methods are largely based on ambient ionization techniques that can suffer from matrix effects and poor selectivity. A strategy that addresses these shortcomings is condensed phase membrane introduction mass spectrometry-liquid electron ionization utilizing in situ liquid reagent chemical ionization (CP-MIMS-LEI/CI). In CP-MIMS measurements, a semipermeable hollow fiber polydimethylsiloxane membrane probe is directly immersed into a complex sample. Neutral, hydrophobic analytes permeating the membrane are entrained by a continuously flowing liquid acceptor phase (nL/min) to an LEI/CI source, where the liquid is nebulized, followed by analyte vaporization and ionization. This study marks the first intentional exploitation of the liquid CP-MIMS acceptor phase as an in situ means of providing liquid chemical ionization (CI) reagents for improved analyte sensitivity and selectivity (CP-MIMS-LEI/CI). Acetonitrile and diethyl ether were used as a combination acceptor phase/CI proton transfer reagent system for the direct analysis of dialkyl phthalates. Using isotopically labeled reagents, the gas phase ionization mechanism was found to involve reagent autoprotonation, followed by proton transfer to dialkyl phthalates. A demonstration of the applicability of CP-MIMS-LEI/CI for rapid and sensitive screening of bis(2-ethylhexyl) phthalate in house dust samples is presented. The detection limit in house dust (6 mg/kg) is comparable to that obtained by conventional analyses, but without time-consuming sample workup or chromatographic separation steps.

Mass Spectrometry Based Approach for Organic Synthesis Monitoring.

Current mass spectrometry-based methodologies for synthetic organic reaction monitoring largely use electrospray ionization (ESI), or other related atmospheric pressure ionization-based approaches. Monitoring of complex, heterogeneous systems may be problematic because of sampling hardware limitations, and many relevant analytes (neutrals) exhibit poor ESI performance. An alternative monitoring strategy addressing this significant impasse is condensed phase membrane introduction mass spectrometry using liquid electron ionization (CP-MIMS-LEI). In CP-MIMS, a semipermeable silicone membrane selects hydrophobic neutral analytes, rejecting particulates and charged chemical components. Analytes partition through the membrane, and are then transported to the LEI interface for sequential nebulization, vaporization, and ionization. CP-MIMS and LEI are both ideal for continuous monitoring applications of hydrophobic neutral molecules. We demonstrate quantitative reaction monitoring of harsh, complex reaction mixtures (alkaline, acidic, heterogeneous) in protic and aprotic organic solvents. Also presented are solvent-membrane compatibility investigations and, in situ quantitative monitoring of catalytic oxidation and alkylation reactions.

Paper spray mass spectrometry: A new drug checking tool for harm reduction in the opioid overdose crisis.

Fentanyl and related psychoactive substances are at the forefront of the opioid overdose crisis, for which a complete solution is not immediately obvious. Drug testing for harm reduction may be an effective approach to both reduce overdoses and importantly, engage people who use drugs (PWUD) with the medical system. Paper spray mass spectrometry (PS-MS) is an ambient ionization strategy that is uniquely suited to address this complicated analytical task. This perspectives article presents the merits of PS-MS, with a focus upon the current state of its use as a candidate drug checking strategy for harm reduction. PS-MS is inherently sensitive and selective, with detection limits in the picogram range. It requires small drug samples (~1 mg) for quantitative drug testing, critical to encourage pre-consumption measurements by PWUD in the context of a harm reduction strategy. Calibrations obtained in surrogate drug matrices containing highly concentrated primary drugs demonstrate comparable sensitivities, a wide calibration range, and minimal matrix effects. PS-MS can be interfaced with high-resolution MS for non-targeted analysis, allowing the identification of novel psychoactive substances as they appear in street drugs. Individual quantitative PS-MS measurements for drug testing can be done in 1 minute or less, resulting in high sample throughput. Significant advancement in mass spectrometer miniaturization and mobilization has concomitant benefits for direct, on-site drug checking, such as reduced cost, simplified maintenance and ease of use by less skilled operators. While PS-MS technology continues to rapidly advance, it is our opinion that PS-MS can be utilized as an effective tool for harm reduction in the opioid overdose crisis.

Direct Analysis of Polyaromatic Hydrocarbons in Soil and Aqueous Samples Using Condensed Phase Membrane Introduction Tandem Mass Spectrometry with Low-Energy Liquid Electron Ionization.

Polyaromatic hydrocarbons (PAHs) are listed as priority pollutants by the United States Environmental Protection Agency (U.S. EPA). PAH-contaminated samples often require extensive sample cleanup before analysis, with the method used dependent upon the sample matrix. We present condensed phase membrane introduction mass spectrometry with liquid electron ionization (CP-MIMS-LEI) as a sensitive and universal technique that can directly analyze both aqueous and soil samples for PAHs without the need for sample clean up or instrumental modifications for different matrixes. The method uses a semipermeable hollow fiber membrane immersion probe to transfer analytes from complex samples into a solvent acceptor phase that is directly entrained at nanoliter/min flows to an LEI-interfaced mass spectrometer. The resulting aerosol is desolvated under vacuum leading to analyte vaporization and subsequent electron ionization. Electron energy and LEI vaporization capillary position were examined and optimized for PAHs. The CP-MIMS probe was directly immersed in complex aqueous matrixes, demonstrating low nanogram per liter PAH detection limits and response times of ≤1.6 min. For soil sample analysis, 2-propanol was found to be the optimal PAH sampling solvent. Soil samples were briefly sonicated in 2-propanol, followed by direct CP-MIMS measurement. Soil sample throughput was ca. 15 samples/h, with PAH quantitation successful at microgram per kilogram levels. The workflow is remarkably simple, fast, green, and leads to reproducible results that enable high-throughput screening of heterogeneous soil samples.

Paper spray mass spectrometry for the direct, semi-quantitative measurement of fentanyl and norfentanyl in complex matrices.

BACKGROUND: Fentanyl is a potent, synthetic opioid at the centre of an international health crisis that has seen thousands of fatal overdoses. Most analytical methods focus on the detection of fentanyl in blood and/or urine (i.e., post-drug use). Harm reduction (including pre-screening before drug use) may be an effective strategy against fentanyl overdoses. METHOD: Paper spray-mass spectrometry (PS-MS) is an inexpensive, direct sampling strategy where a small volume of sample (<10 µL) is spotted onto a piece of paper that is then wetted and connected to high voltage. Ions are emitted from the paper and enter a mass spectrometer for sensitive and selective semi-quantitation using labeled internal standards. RESULTS: We present the use of PS-MS for the direct measurement of fentanyl and norfentanyl using a custom PS interface, demonstrating that paper tip position and quality can significantly affect quantitative results. Furthermore, we observe comparable calibrations for fentanyl and norfentanyl (0.5 to 600 ng/mL) across a variety of complex matrices (methanol, diluted urine, analgesic slurry). Detection limits for fentanyl are as low as 0.049 ng/mL (0.4 pg total material) in methanol, and 0.66 ng/mL (5.3 pg total material) spiked in an analgesic slurry (illicit substance simulation). PS-MS was compared with liquid chromatography-MS for the analyses of real urine samples, with satisfactory results. CONCLUSION: PS-MS shows potential as a sensitive and selective direct measurement strategy for use in fentanyl harm reduction strategies, and may also be used for pre-screening in advance of or in combination with more conventional (i.e., chromatographic) analyses.

Polymer Inclusion Membranes with Condensed Phase Membrane Introduction Mass Spectrometry (CP-MIMS): Improved Analytical Response Time and Sensitivity.

Condensed phase membrane introduction mass spectrometry (CP-MIMS) is an online, in situ analysis technique for low volatility analytes. Analytes diffuse through a hollow fiber membrane, where they are then dissolved by a liquid (condensed) acceptor phase flowing through the membrane lumen. Permeating analytes are entrained to an atmospheric pressure ionization source for subsequent measurement by a mass spectrometer. Larger analytes, with inherently lower diffusivities, suffer from lengthy response times and lower sensitivity, limiting the use of CP-MIMS for their online, real-time measurement. We present the use of a heptane cosolvent in a methanol acceptor phase in combination with a polydimethylsiloxane (PDMS) membrane. The heptane generates an in situ polymer inclusion membrane (PIM) with the PDMS. We report improved measurement response times and greater sensitivity across a suite of analytes studied (gemfibrozil, nonylphenol, triclosan, 2,4,6-trichlorophenol, and naphthenic acids), with detection limits in the low parts per trillion (ppt) range. These improvements are attributed to increasing analyte diffusivities, as well as increased analyte partitioning across the PIM. Response times are ∼3× faster for the larger analytes studied, and calibration sensitivity is improved by up to ∼3.5× using 0.046 mole fraction heptane in the methanol acceptor. We report the use of short sample exposure times and the use of non-steady-state signals to reduce the analytical duty cycle, and illustrate that the use of a PIM provides a simple and robust variant of CP-MIMS amenable to rapid screening of analytes in complex samples.

A semi-quantitative approach for the rapid screening and mass profiling of naphthenic acids directly in contaminated aqueous samples.

We report the use of a direct sampling, online analytical approach for the determination of acid extractable naphthenic acids in complex aqueous samples, known as condensed phase membrane introduction mass spectrometry (CP-MIMS). The technique employs a capillary hollow fibre semi-permeable membrane probe configured for immersion into a pH adjusted sample. A continuously flowing methanol acceptor phase transfers naphthenic acids to an electrospray ionization source, operated in negative ion mode, whereupon they are analysed by mass spectrometry as [M-H](-) ions. High-resolution mass spectrometry is used to characterize the influence of sample pH on membrane transport of multiple components of complex naphthenic acid mixtures. We demonstrate the use of CP-MIMS for semi-quantitative analysis of real-world samples using selected ion monitoring and full scan mass spectra at unit mass resolution. The technique has also been employed to continuously monitor the temporal evolution in the mass profile and concentrations of individual naphthenic acid isomer classes in heterogeneous solutions during adsorption processes. Copyright © 2015 John Wiley & Sons, Ltd.

Condensed Phase Membrane Introduction Mass Spectrometry with Direct Electron Ionization: On-line Measurement of PAHs in Complex Aqueous Samples.

Polycyclic aromatic hydrocarbons (PAHs) are USEPA regulated priority pollutants. Their low aqueous solubility requires very sensitive analytical methods for their detection, typically involving preconcentration steps. Presented is the first demonstrated 'proof of concept' use of condensed phase membrane introduction mass spectrometry (CP-MIMS) coupled with direct liquid electron ionization (DEI) for the direct, on-line measurement of PAHs in aqueous samples. DEI is very well suited for the ionization of PAHs and other nonpolar compounds, and is not significantly influenced by the co-elution of matrix components. Linear calibration data for low ppb levels of aqueous naphthalene, anthracene, and pyrene is demonstrated, with measured detection limits of 4 ppb. Analytical response times (t10%­90% signal rise) ranged from 2.8 min for naphthalene to 4.7 min for pyrene. Both intra- and interday reproducibility has been assessed (<3% and 5% RSD, respectively). Direct measurements of ppb level PAHs spiked in a variety of real, complex environmental sample matrices is examined, including natural waters, sea waters, and a hydrocarbon extraction production waste water sample. For these spiked, complex samples, direct PAH measurement by CP-MIMS-DEI yielded minimal signal suppression from sample matrix effects (81%­104%). We demonstrate the use of this analytical approach to directly monitor real-time changes in aqueous PAH concentrations with potential applications for continuous on-line monitoring strategies and binding/adsorption studies in heterogeneous samples.