Heat-induced morphological changes in silver nanowires deposited on a patterned silicon substrate.

Metallic nanowires (NWs) are sensitive to heat treatment and can split into shorter fragments within minutes at temperatures far below the melting point. This process can hinder the functioning of NW-based devices that are subject to relatively mild temperatures. Commonly, heat-induced fragmentation of NWs is attributed to the interplay between heat-enhanced diffusion and Rayleigh instability. In this work, we demonstrated that contact with the substrate plays an important role in the fragmentation process and can strongly affect the outcome of the heat treatment. We deposited silver NWs onto specially patterned silicon wafers so that some NWs were partially suspended over the holes in the substrate. Then, we performed a series of heat-treatment experiments and found that adhered and suspended parts of NWs behave differently under the heat treatment. Moreover, depending on the heat-treatment process, fragmentation in either adhered or suspended parts can dominate. Experiments were supported by finite element method and molecular dynamics simulations.

Sol-Gel TiO2 Thin Film on Au Nanoparticles for Heterogeneous Plasmonic Photocatalysis.

A new, simple method for preparing substrates for photocatalytic applications under visible light is presented. It is based on the preparation of a dense array of gold nanoparticles (AuNPs) by thermal dewetting of a thin gold film followed by spin-coating of a thin TiO2 film prepared by sol-gel chemistry. The photocatalytic properties of these nanocomposite films are studied by surface-enhanced Raman spectroscopy (SERS) following the N-demethylation reaction of methylene blue as a model reaction. This approach shows that the semiconducting layer on the AuNPs can significantly increase the efficiency of the photoinduced reaction. The SERS study also illustrates the influence of parameters such as TiO2 thickness and position (on or under the AuNPs). Ultimately, this study emphasizes that the primary mechanism behind the N-demethylation reaction is both the increase in extinction and the improved electron transfer facilitated by the semiconducting layer. On the other hand, exclusive reliance on photothermal effects is ruled out.

Enhancing the Properties of Photo-Generated Metallized Nanocomposite Coatings through Thermal Annealing.

In this work, the effect of thermal annealing on silver nanoparticles@polymer (AgNPs@polymer) nanocomposite coatings was investigated. These photo-generated metallized coatings have a spatial distribution of metal nanoparticles, with a depth-wise decrease in their concentration. During annealing, both structural and morphological variations, as well as a spatial reorganization of AgNPs, were observed, both at the surface and in the core of the AgNPs@polymer coating. Owing to their increased mobility, the polymer chains reorganize spontaneously, and, at the same time, a hopping diffusion process, caused by the minimization of the surface energy, promotes the migration and coalescence of the silver nanoparticles towards the surface. The layer of discrete nanoparticles gradually transforms from a weakly percolative assembly to a denser and more networked structure. Consequently, the surface of the coatings becomes significantly more electrically conductive, hydrophobic, and reflective. The general trend is that the thinner the nanohybrid coating, the more pronounced the effect of thermal annealing on its spatial reorganization and properties. These results open up interesting prospects in the field of metallized coating technology and pave the way for integration into a wide variety of devices, e.g., efficient and inexpensive reflectors for energy-saving applications, electrically conductive microdevices, and printed electronic microcircuits.

Synthesis and Structural Insight into poly(dimethylsiloxane)-b-poly(2-vinylpyridine) Copolymers.

In this study, the use of anionic polymerization for the synthesis of living poly(dimethylsiloxane) or PDMS-Li+, as well as poly(2-vinylpyridine) or P2VP-Li+ homopolymers, and the subsequent use of chlorosilane chemistry in order for the two blocks to be covalently joined leading to PDMS-b-P2VP copolymers is proposed. High vacuum manipulations enabled the synthesis of well-defined materials with different molecular weights (Μ¯n, from 9.8 to 36.0 kg/mol) and volume fraction ratios (φ, from 0.15 to 0.67). The Μ¯n values, dispersity indices, and composition were determined through membrane/vapor pressure osmometry (MO/VPO), size exclusion chromatography (SEC), and proton nuclear magnetic resonance spectroscopy (1H NMR), respectively, while the thermal transitions were determined via differential scanning calorimetry (DSC). The morphological characterization results suggested that for common composition ratios, lamellar, cylindrical, and spherical phases with domain periodicities ranging from approximately 15 to 39 nm are formed. A post-polymerization chemical modification reaction to quaternize the nitrogen atom in some of the P2VP monomeric units in the copolymer with the highest P2VP content, and the additional characterizations through 1H NMR, infrared spectroscopy, DSC, and contact angle are reported. The synthesis, characterization, and quaternization of the copolymer structure are important findings toward the preparation of functional materials with enhanced properties suitable for various nanotechnology applications.

Not Just Another Methanation Catalyst: Depleted Uranium Meets Nickel for a High-Performing Process Under Autothermal Regime.

Invited for this month's cover are collaborating teams from academia-the French ICPEES and IS2M of Centre national de la recherche scientifique (CNRS) and the Italian ICCOM of Consiglio Nazionale delle Ricerche (CNR)-and industry with the participation of the ORANO group. The cover picture shows a CO2 -to-CH4 process promoted by nickel nanoparticles supported on depleted uranium oxide under exceptionally low temperature values or autothermal conditions. The Research Article itself is available at 10.1002/cssc.202201859.

(NHC-olefin)-nickel(0) nanoparticles as catalysts for the (Z)-selective semi-hydrogenation of alkynes and ynamides.

Nickel(0) nanoparticles coordinated to NHC ligands bearing N-coordinated cinnamyl moieties were readily prepared by reduction of a [NiCpBr(NHC-cinnamyl)] complex with methyl magnesium bromide. The combination of a strong σ-donor NHC ligand with a π-coordinating appended cinnamyl moiety likely prevents nickel(0) nanoparticle aggregation to larger inactive species, and allows the effective and (Z)-selective semi-hydrogenation of alkynes and ynamides.

Not Just Another Methanation Catalyst: Depleted Uranium Meets Nickel for a High-Performing Process Under Autothermal Regime.

Ni-based catalysts prepared through impregnation of depleted uranium oxides (DU) have successfully been employed as highly efficient, selective, and durable systems for CO2 hydrogenation to substituted natural gas (SNG; CH4 ) under an autothermal regime. The thermo-physical properties of DU and the unique electronic structure of f-block metal-oxides combined with a nickel active phase, generated an ideal catalytic assembly for turning waste energy back into useful energy for catalysis. In particular, Ni/UOx stood out for the capacity of DU matrix to control the extra heat (hot-spots) generated at its surface by the highly exothermic methanation process. At odds with the benchmark Ni/γ-Al2 O3 catalyst, the double action played by DU as a "thermal mass" and "dopant" for the nickel active phase unveiled the unique performance of Ni/UOx composites as CO2 methanation catalysts. The ability of the weakly radioactive ceramic (UOx ) to harvest waste heat for more useful purposes was demonstrated in practice within a rare example of a highly effective and long-term methanation operated under autothermal regime (i. e., without any external heating source). This finding is an unprecedented example that allows a real step-forward in the intensification of "low-temperature" methanation with an effective reduction of energy wastes. At the same time, the proposed catalytic technology can be regarded as an original approach to recycle and bring to a second life a less-severe nuclear by-product (DU), providing a valuable alternative to its more costly long-term storage or controlled disposal.

Shape influence on the ultrafast plasmonic properties of gold nanoparticles.

The aim of shape-controlled colloidal synthesis of gold (Au) is to produce Au nanoparticles (NPs) with fine control of shapes, sizes, and dispersities. We show how transient absorption spectroscopy (TAS) can be used to rapidly and accurately quantify the vast ensemble of shapes of Au NPs in solution within minutes, including the synthesized nanorods, decahedra, and nanospheres. Colloidal solutions containing Au NPs were measured in TAS and their localized surface plasmon resonance (LSPR) modes were classified according to the shape, wavelength and number of peaks. Then their excited-state relaxation dynamics were used to ascertain their electron-phonon (e-ph) coupling time constant and frequency of optomechanical modes. TAS can quickly show that an Au nanosphere sample contains a tiny fraction of Au nanorods, whereas steady-state absorbance is totally blind to the presence of nanorods. Additionally, the TAS experiments indicate that the characteristic e-ph coupling time constants in Au nanorods depend on the NPs dimensions at high excitation intensity (> 6 µJ/cm2) which can help identify if there are any elongated Au NPs in Au spheres samples. Finally, optomechanical oscillations formed by NPs breathing modes were observed, providing information related to the average size and monodispersity of Au nanospheres and nanorods.

Kinetically stable sub-50 nm fluorescent block copolymer nanoparticles via photomediated RAFT dispersion polymerization for cellular imaging.

Self-assembled block copolymer nanoparticles (NPs) have emerged as major potential nanoscale vehicles for fluorescence bioimaging. The preparation of NPs with high yields possessing high kinetic stability to prevent the leakage of fluorophore molecules is crucial to their practical implementation. Here, we report a photomediated RAFT polymerization-induced self-assembly (PISA) yielding uniform and nanosized poly((oligo(ethylene glycol) acrylate)-block-poly(benzyl acrylate) particles (POEGA-b-PBzA) with a concentration of 22 wt%, over 20 times more than with micellization and nanoprecipitation. The spherical diblock copolymer nanoparticles have an average size of 10-50 nm controllable through the degree of polymerization of the stabilizing POEGA block. Subsequent dialysis against water and swelling with Nile red solution led to highly stable fluorescent NPs able to withstand the changes in concentration, ionic strength, pH or temperature. A PBzA/water interfacial tension of 48.6 mN m-1 hinders the exchange between copolymer chains, resulting in the trapping of NPs in a "kinetically frozen" state responsible for high stability. A spectroscopic study combining fluorescence and UV-vis absorption agrees with a preferential distribution of fluorophores in the outer POEGEA shell despite its hydrophobic nature. Nile red-doped POEGA-b-PBzA micelles without initiator residues and unimers but with high structural stability turn out to be noncytotoxic, and can be used for the optical imaging of cells. Real-time confocal fluorescence microscopy shows a fast cellular uptake using C2C12 cell lines in minutes, and a preferential localization in the perinuclear region, in particular in the vesicles.

Near-Infrared Laser Direct Writing of Conductive Patterns on the Surface of Carbon Nanotube Polymer Nanocomposites.

Near-infrared (NIR) laser annealing is used to write conductive patterns on the surface of polypropylene/multi-walled carbon nanotube nanocomposite (PP/MWCNT) plates. Before irradiation, the surface of the nanocomposite is not conductive due to the partial alignment of the MWCNT, which occurs during injection molding. We observe a significant decrease in the surface sheet resistance using NIR laser irradiation, which we explain by a randomization of the orientation of MWCNTs in the PP matrix melt by NIR laser irradiation. After only 5 s of irradiation, the sheet resistance of PP/MWCNTs, annealed with a laser at a power density of 7 W/cm2, decreases by more than 4 decades from ∼100 MΩ/sq to ∼1 kΩ/sq. Polarized Raman, TEM, and SEM are used to investigate the changes in the sheet resistance and confirm the physico-chemical processes involved. This allows direct writing of conductive patterns using a NIR laser on the surface of nanocomposite polymer substrates, with the advantages of a fast, easy, and low-energy consumption process.

Does the photocatalytic activity of nanoparticles protect the marine mussel Mytilus galloprovincialis from polycyclic aromatic hydrocarbon toxicity?

In the present study, five NPs (containing ZnO, Au-ZnO, Cu-ZnO, TiO2, and Au-TiO2) were characterized using dynamic light scattering and transmission electron microscopy, in order to observe their behavior under environmental change. The applicability of NPs for degradation of three polycyclic aromatic hydrocarbons (PAHs), including benzo(a)pyrene, fluoranthene, and benzanthracene, using UV irradiation showed the high photocatalytic efficiency of doped NPs for the removal of the study pollutants. To predict the environmental impact and interaction between NPs and PAHs on marine organisms, Mytilus galloprovincialis mussels were exposed to concentrations of each chemical (50 and 100 µg/L) for 14 days. The mussel's response was determined using the oxidative stress biomarker approach. Measured biomarkers in the mussel's digestive gland showed possible oxidative mechanisms in a concentration-dependent manner occurring after exposure to PAHs and NPs separately. Overall, this finding provides an interesting combination to remove PAHs in water, and the incorporation of chemical element into the crystallographic structure of NPs and the combination of two different NPs to form a binary hybrid NPs are promising materials.

Characterizing the Core-Shell Architecture of Block Copolymer Nanoparticles with Electron Microscopy: A Multi-Technique Approach.

Electron microscopy has proved to be a major tool to study the structure of self-assembled amphiphilic block copolymer particles. These specimens, like supramolecular biological structures, are problematic for electron microscopy because of their poor capacity to scatter electrons and their susceptibility to radiation damage and dehydration. Sub-50 nm core-shell spherical particles made up of poly(hydroxyethyl acrylate)-b-poly(styrene) are prepared via polymerization-induced self-assembly (PISA). For their morphological characterization, we discuss the advantages, limitations, and artefacts of TEM with or without staining, cryo-TEM, and SEM. A number of technical points are addressed such as precisely shaping of particle boundaries, resolving the particle shell, differentiating particle core and shell, and the effect of sample drying and staining. TEM without staining and cryo-TEM largely evaluate the core diameter. Negative staining TEM is more efficient than positive staining TEM to preserve native structure and to visualize the entire particle volume. However, no technique allows for a satisfactory imaging of both core and shell regions. The presence of long protruding chains is manifested by patched structure in cryo-TEM and a significant edge effect in SEM. This manuscript provides a basis for polymer chemists to develop their own specimen preparations and to tackle the interpretation of challenging systems.

Diblock Copolymer Core-Shell Nanoparticles as Template for Mesoporous Carbons: Independent Tuning of Pore Size and Pore Wall Thickness.

Latex templating using core-shell particles represents a unique opportunity to design mesoporous carbons with a high level of control on textural properties. This new class of organic colloid templates is synthesized by polymerization-induced self-assembly (PISA) in which a solvophilic poly(hydroxyethyl acrylate) (PHEA) homopolymer is chain extended with a solvophobic polystyrene (PS) via a photomediated reversible-addition-fragmentation-transfer (RAFT) polymerization. The resultant PHEA-b-PS diblock copolymer nanoparticles exhibit a PS core stabilized by a PHEA shell, with two blocks characterized by a low molecular weight dispersity (1.1-1.3) and an adjustable degree of polymerization (DP). The core-shell structured nanoparticles are used as soft template for the formation of mesostructured carbons from phloroglucinol and glyoxylic acid in methanol solution. A micro- and mesostructured cellular foam is obtained having uniform, interconnected, and narrowly distributed mesopores ranging between 15 and 30 nm in diameter, a specific surface area up to 719 m2 g-1, and a total pore volume of (0.4-1.3) cm3 g-1. The mesopore size can be controlled by adjusting the diameter of the PS core (16-29 nm), while the wall thickness can be tailored independently by varying the size of the solvated PHEA shell (5-25 nm). An increase of PHEA block's DP from 25 to 85 gradually extends the stabilizing shell dimension, thus increasing the wall thickness up to 10 nm, and causing the shift from interconnected to isolated mesopores. By comparison, much thinner walls (2-3 nm) are obtained with conventional latex templates such as polystyrene nanoparticles or colloidal silica. Decreasing PHEA DP to 17 induces the formation of copolymer vesicles that can be used as template to create mesoporous carbons with nonspherical mesopores.

Binary Oxides Prepared by Microwave-Assisted Solution Combustion: Synthesis, Characterization and Catalytic Activity.

Three different alumina-based Ni, Cu, Co oxide catalysts with metal loading of 10 wt %, and labeled 10Ni⁻Al, 10Co⁻Al and 10Cu⁻Al, were prepared by microwave-assisted solution combustion. Their morphological, structural and surface properties were deeply investigated by complementary physico-chemical techniques. Finally, the three materials were tested in CO oxidation used as test reaction for comparing their catalytic performance. The 10Cu⁻Al catalyst was constituted of copper oxide phase, while the 10Ni⁻Al and 10Co⁻Al catalysts showed the presence of "spinels" phases on the surface. The well-crystallized copper oxide phase in the 10Cu⁻Al catalyst, obtained by microwave synthesis, allowed for obtaining very high catalytic activity. With a CO conversion of 100% at 225 °C, the copper containing catalyst showed a much higher activity than that usually measured for catalytic materials of similar composition, thus representing a promising alternative for oxidation processes.

Generating highly reflective and conductive metal layers through a light-assisted synthesis and assembling of silver nanoparticles in a polymer matrix.

The development of metalized surfaces exhibiting mirror properties and/or electric conductivity without heavy equipments and with low metal charge is a big challenge in view of many industrial applications. We report herein on the photo-assembling of silver nanoparticles (AgNPs) in a polymer matrix, carried out within minutes from an acrylate monomer and silver nitrate at room temperature, under air and without any solvents. The top surface of the material gets converted into a continuous silver thin film and a depthwise concentration gradient of AgNPs is created in the polymer, which images the absorption profile of the actinic UV light in the reactive formulation. This specific assembling of the silver@polymer coating induces excellent reflective and conductive properties. The conductance was observed to strongly increase with increasing the exposure from 3 to 30 min due to the formation of a more and more compact metal film. This coating strategy works with a variety of substrates (textile, paper, glass, wood, plastic and stainless steel). Moreover, on flexible surfaces such as textile, the flexibility was preserved. The possibility to use this kind of nanomaterial as a printing ink, with a much lower metal concentration (3 to 5 wt.%) than concurrent inks, was also demonstrated.

Tuning the morphology of silver nanostructures photochemically coated on glass substrates: an effective approach to large-scale functional surfaces.

This paper reports on a simple and environmentally friendly photochemical process capable of generating nano-layers (8-22 nm) of silver nanostructures directly onto glass surfaces. This approach opens the way to large-scale functionalized surfaces with plasmonic properties through a single light-induced processing. Thus, Ag nanostructures top-coated were obtained through photo-reduction, at room temperature, of a photosensitive formulation containing a metal precursor, free from extra toxic stabilizers or reducing agents. The reactive formulation was confined between two glass slides and exposed to a continuous near-UV source. In this way, stable silver nano-layers can be generated directly on the substrate with a very good control of the morphology of as-synthesized nanostructures that allows tailoring the optical properties of the coated layers. The position and width of the corresponding surface plasmon resonance bands can be adjusted over a broad spectral window. By extension, this low-cost and easy-to-apply process can also be used to coat ultra thin layers of metal nanostructures on a variety of substrates. The possibility of controlling of nanostructures shape should achieve valuable developments in many fields, as diverse as plasmonics, surface enhanced Raman scattering, nano-electronic circuitry, or medical devices.

Insights into the Formation and Properties of Templated Dual Mesoporous Titania with Enhanced Photocatalytic Activity.

The one pot synthesis of dual mesoporous titania (2.3 and 7.7 nm) has been achieved from a mixture of fluorinated and Pluronic surfactants. The small and large mesopore networks are templated, respectively, by a fluorinated-rich liquid crystal and a Pluronic-rich liquid crystal, which are in equilibrium. After calcination at 350 °C, the amorphous walls are transformed into semicrystalline anatase preserving the mesoporous structure. Results concerning the photodegradation of methyl orange using the calcined photocatalysts highlight that the kinetic rate constant (k) determined for the dual mesoporous titania is 2.6 times higher than the k value obtained for the monomodal ones.

An efficient photochemical route to Pd nanoparticles; application to the one-step synthesis of Pd@polymer nanocomposite films.

We have developed a facile, efficient, low cost and 'green' photochemical approach to preparing surfactant-free Pd nanoparticles and Pd-immobilized@acrylate photo-polymer films at room temperature, under air and without any additional treatment. The reaction system only includes a photo-initiator used as a generator of free radicals and a Pd(II) salt. In ethanol solution, the photochemical reduction of Pd(II) to Pd(0) generates very small metal particles with a narrow size distribution (2-4 nm). Furthermore, we have shown that the formation of Pd nanoparticles from a Pd(II) salt can be reversible thus allowing easy handling and safe storage with the possibility of generating the nanoparticles just before use. In the presence of an acrylate bifunctional monomer, Pd@polymer film was obtained through a 'one-pot, one-step' process resulting from a simultaneous photo-reduction of Pd(II) and photo-polymerization of acrylate units. The simultaneous generation of a 3D polymer network and of metal particles leads to a homogeneous distribution of Pd nanoparticles in the photo-polymer matrix with an average diameter of approximately 3.7 ± 1.1 nm. Such as-prepared Pd@polymer films were found to efficiently catalyze the Mizoroki-Heck reaction in the presence of only 0.9 mequiv. of supported palladium. The major interest of this arrangement is its recoverability and reusability, which makes it very attractive both from a practical and economical viewpoint. Finally, it is worth noting that this innovation offers a great advantage over concurrent methods in that it is simply generated within minutes, it is highly stable, and there is sharp monodispersity in the size of the Pd nanoparticles that can be stored for months without alteration of their physico-chemical properties and catalytic activity.

In Situ Small-Angle X-ray Scattering Investigation of the Formation of Dual-Mesoporous Materials.

The formation of a 2D-hexagonal (p6m) silica-based hybrid dual-mesoporous material is investigated in situ by using synchrotron time-resolved small-angle X-ray scattering (SAXS). The material is synthesized from a mixed micellar solution of a nonionic fluorinated surfactant, R(F) 8 (EO)9 (EO=ethylene oxide) and a nonionic triblock copolymer, P123. Both mesoporous networks, with pore dimensions of 3.3 and 8.5 nm respectively, are observed by nitrogen sorption, transmission electron microscopy (TEM), and SAXS. The in situ SAXS experiments reveal that mesophase formation occurs in two steps. First the nucleation and growth of a primary 2D-hexagonal network (N1), associated with mixed micelles containing P123, then subsequent formation of a second network (N2), associated with micelles of pure R(F) 8 (EO)9 . The data obtained from SAXS and TEM suggest that the N1 network is used as a nucleation center for the formation of the N2 network, which would result in the formation of a grain with two mesopore sizes. Understanding the mechanism of the formation of such materials is an important step towards the synthesis of more-complex materials by fine tuning the porosity.

In vitro and in vivo evaluation of the inflammatory potential of various nanoporous hydroxyapatite biomaterials.

AIM: To discriminate the most important physicochemical parameters for bone reconstruction, the inflammatory potential of seven nanoporous hydroxyapatite powders synthesized by hard or soft templating was evaluated both in vitro and in vivo. MATERIALS & METHODS: After physical and chemical characterization of the powders, we studied the production of inflammatory mediators by human primary monocytes after 4 and 24 h in contact with powders, and the host response after 2 weeks implantation in a mouse critical size defect model. RESULTS: In vitro results highlighted increases in the secretion of TNF-α, IL-1, -8, -10 and proMMP-2 and -9 and decreases in the secretion of IL-6 only for powders prepared by hard templating. In vivo observations confirmed an extensive inflammatory tissue reaction and a strong resorption for the most inflammatory powder in vitro. CONCLUSION: These findings highlight that the most critical physicochemical parameters for these nanoporous hydroxyapatite are, the crystallinity that controls dissolution potential, the specific surface area and the size and shape of crystallites.