Biomaterials and tissue engineering approaches using glycosaminoglycans for tissue repair: Lessons learned from the native extracellular matrix.

Glycosaminoglycans (GAGs) are an important component of the extracellular matrix as they influence cell behavior and have been sought for tissue regeneration, biomaterials, and drug delivery applications. GAGs are known to interact with growth factors and other bioactive molecules and impact tissue mechanics. This review provides an overview of native GAGs, their structure, and properties, specifically their interaction with proteins, their effect on cell behavior, and their mechanical role in the ECM. GAGs' function in the extracellular environment is still being understood however, promising studies have led to the development of medical devices and therapies. Native GAGs, including hyaluronic acid, chondroitin sulfate, and heparin, have been widely explored in tissue engineering and biomaterial approaches for tissue repair or replacement. This review focuses on orthopaedic and wound healing applications. The use of GAGs in these applications have had significant advances leading to clinical use. Promising studies using GAG mimetics and future directions are also discussed. STATEMENT OF SIGNIFICANCE: Glycosaminoglycans (GAGs) are an important component of the native extracellular matrix and have shown promise in medical devices and therapies. This review emphasizes the structure and properties of native GAGs, their role in the ECM providing biochemical and mechanical cues that influence cell behavior, and their use in tissue regeneration and biomaterial approaches for orthopaedic and wound healing applications.

Ceiling impact on air disinfection performance of Upper-Room Germicidal Ultraviolet (UR-GUV).

This study used Computational Fluid Dynamics (CFD) to investigate air disinfection for SARS-CoV-2 by the Upper-Room Germicidal Ultraviolet (UR-GUV), with focus on ceiling impact. The study includes three indoor settings, i.e., low (airport bus), medium (classroom) and high (rehearsal room) ceilings, which were ventilated with 100% clean air (CA case), 80% air-recirculation with a low filtration (LF case), and 80% air-recirculation with a high filtration (HF case). According to the results, using UR-GUV can offset the increased infection risk caused by air recirculation, with viral concentrations in near field (NF) and far field (FF) in the LF case similar to those in the CA case. In the CA case, fraction remaining (FR) was 0.48-0.73 with 25% occupancy rate (OR) and 0.49-0.91 with 45% OR in the bus, 0.41 in NF and 0.11 in FF in the classroom, and 0.18 in NF and 0.09 in FF in the rehearsal room. Obviously, UR-GUV performance in NF can be improved in a room with a high ceiling where FR has a power relationship with UV zone height. As using UR-GUV can only extend the exposure time to get infection risk of 1% (T 1% ) to 8 min in NF in the classroom, and 47 min in NF in the rehearsal room, it is necessary to abide by social distancing in the two rooms. In addition, T 1% in FF was calculated to be 18.3 min with 25% OR and 21.4% with 45% OR in the airport bus, showing the necessity to further wear a mask.

Plant cell adhesion and growth on artificial fibrous scaffolds as an in vitro model for plant development.

Mechanistic studies of plant development would benefit from an in vitro model that mimics the endogenous physical interactions between cells and their microenvironment. Here, we present artificial scaffolds to which both solid- and liquid-cultured tobacco BY-2 cells adhere without perturbing cell morphology, division, and cortical microtubule organization. Scaffolds consisting of polyvinylidene tri-fluoroethylene (PVDF-TrFE) were prepared to mimic the cell wall's fibrillar structure and its relative hydrophobicity and piezoelectric property. We found that cells adhered best to scaffolds consisting of nanosized aligned fibers. In addition, poling of PVDF-TrFE, which orients the fiber dipoles and renders the scaffold more piezoelectric, increased cell adhesion. Enzymatic treatments revealed that the plant cell wall polysaccharide, pectin, is largely responsible for cell adhesion to scaffolds, analogous to pectin-mediated cell adhesion in plant tissues. Together, this work establishes the first plant biomimetic scaffolds that will enable studies of how cell-cell and cell-matrix interactions affect plant developmental pathways.

Scalable, effective, and rapid decontamination of SARS-CoV-2 contaminated N95 respirators using germicidal ultraviolet C (UVC) irradiation device.

Particulate respirators such as N95s are an essential component of personal protective equipment (PPE) for front-line workers. This study describes a rapid and effective UVC irradiation system that would facilitate the safe re-use of N95 respirators and provides supporting information for deploying UVC for decontamination of SARS-CoV-2 during the COVID-19 pandemic. To assess the inactivation potential of the proposed UVC germicidal device as a function of time by using 3 M 8211-N95 particulate respirators inoculated with SARS-CoV-2. A germicidal UVC device to deliver tailored UVC dose was developed and test coupons (2.5 cm2) of the 3 M-N95 respirator were inoculated with 106 plaque-forming units (PFU) of SARS-CoV-2 and were UV irradiated. Different exposure times were tested (0-164 s) by fixing the distance between the lamp and the test coupon to 15.2 cm while providing an exposure of at least 5.43 mWcm-2. Primary measure of outcome was titration of infectious virus recovered from virus-inoculated respirator test coupons after UVC exposure. Other measures included the method validation of the irradiation protocol, using lentiviruses (biosafety level-2 agent) and establishment of the germicidal UVC exposure protocol. An average of 4.38 × 103 PFU ml-1 (SD 772.68) was recovered from untreated test coupons while 4.44 × 102 PFU ml-1 (SD 203.67), 4.00 × 102 PFU ml-1 (SD 115.47), 1.56 × 102 PFU ml-1 (SD 76.98) and 4.44 × 101 PFU ml-1 (SD 76.98) was recovered in exposures 2, 6, 18 and 54 s per side respectively. The germicidal device output and positioning was monitored and a minimum output of 5.43 mW cm-2 was maintained. Infectious SARS-CoV-2 was not detected by plaque assays (minimal level of detection is 67 PFU ml-1) on N95 respirator test coupons when irradiated for 120 s per side or longer suggesting 3.5 log reduction in 240 s of irradiation, 1.3 J cm-2. A scalable germicidal UVC device to deliver tailored UVC dose for rapid decontamination of SARS-CoV-2 was developed. UVC germicidal irradiation of N95 test coupons inoculated with SARS-CoV-2 for 120 s per side resulted in 3.5 log reduction of virus. These data support the reuse of N95 particle-filtrate apparatus upon irradiation with UVC and supports use of UVC-based decontamination of SARS-CoV-2 during the COVID-19 pandemic.

Toward a Test Protocol for Surface Decontamination Using a Mobile Whole-room UVGI Device†.

Mobile whole-room UVGI devices are used in healthcare settings to control surface-borne pathogens. Unfortunately, no standard method comparing the efficacy of these devices is available. We accessed the effect of shadows on UVC 254 nm inactivation. The evaluation of a mobile whole-room UVGI device used spores of Bacillus atrophaeus as a surrogate for Clostridium difficile and Staphylococcus aureus as a surrogate for MSRA. Inactivation after 10 min of exposure varied significantly depending on whether the spores received direct UV exposure (4.3 log reduction), both direct and reflected UV exposure (3.0-4.0 log reduction) or reflected UV exposure alone (<1.0 log reduction). The susceptibility (z-value) for inactivation of B. atrophaeus spores on a glass surface was estimated to be 0.00312 m2  J-1 . Staphylococcus aureus microbial log reductions were approximately 5.5 for direct UV exposure, 3.6-5.2 for both direct and reflected UV exposure and approximately 2.75 for only reflected UV exposure. Our measurement of reflected dose ranged from 0.46% to 1.47%. Based on our findings, B. atrophaeus spores should be considered as a model organism for testing the impact of shadows on mobile whole-room UVGI device inactivation. Optimizing the reflected component of whole-room UVGI is important, especially for UVC-resistant organisms.

Identification of Pathogens Potentially Associated with Non-Malarial Fever in Children: A Pilot Study in Peri-Urban Dakar, Senegal.

Fever is one of the most common reasons for pediatric consultation in Africa. Malaria incidence has now dropped considerably, yet etiologies of non-malarial febrile diseases are poorly documented. This pilot study aimed to 1) identify pathogens potentially associated with non-malarial fever in children younger than 10 years in the suburbs of Dakar and 2) describe the epidemiological characteristics of these patients. During the study period, all eligible children (< 10 years of age, body temperature ≥ 38°C, negative result for the malaria rapid diagnostic test, living in Guediawaye/Pikine for the previous four calendar months, not receiving any anti-infectious treatment since the onset of fever, and with parent's consent to participate) presenting to the health post in Medina Gounass located in Guediawaye on Mondays and Fridays were included. In total, 106 children participated in the study, and PCR from nasopharyngeal swabs, hemoculture, C-reactive protein, blood cell counts, and quantitative buffy coat from blood samples and coproculture from stool samples were performed. In 70 (66%) children, at least one pathogen was isolated. Viruses were identified in 55 children, most commonly enteroviruses, rhinoviruses, and adenoviruses, and dengue virus was identified in three children. Only five children had bacterial infections, and 10 had bacterial and viral coinfections. Ninety-seven children (92%) received prescription for antibiotics. Many strains of bacteria were found to be resistant to several antibiotics. Despite limitations, this pilot study showed that pathogens potentially associated with non-malarial fever in children younger than 10 years near Dakar were predominantly viruses, most commonly upper respiratory infections, although bacteria accounted for a small proportion.

Scalable, effective, and rapid decontamination of SARS-CoV-2 contaminated N95 respirators using germicidal ultra-violet C (UVC) irradiation device.

IMPORTANCE: Particulate respirators such as N95 masks are an essential component of personal protective equipment (PPE) for front-line workers. This study describes a rapid and effective UVC irradiation system that would facilitate the safe re-use of N95 respirators and provides supporting information for deploying UVC for decontamination of SARS-CoV-2 during the COVID19 pandemic. OBJECTIVE: To assess the inactivation potential of the proposed UVC germicidal device as a function of time by using 3M 8211 - N95 particulate respirators inoculated with SARS-CoV-2. DESIGN: A germicidal UVC device to deliver tailored UVC dose was developed and snippets (2.5cm2) of the 3M-N95 respirator were inoculated with 106 plaque-forming units (PFU) of SARS-CoV-2 and were UV irradiated. Different exposure times were tested (0-164 seconds) by fixing the distance between the lamp (10 cm) and the mask while providing an exposure of at least 5.43 mWcm-2. SETTING: The current work is broadly applicable for healthcare-settings, particularly during a pandemic such as COVID-19. PARTICIPANTS: Not applicable. Main Outcome(s) and Measure(s): Primary measure of outcome was titration of infectious virus recovered from virus-inoculated respirator pieces after UVC exposure. Other measures included the method validation of the irradiation protocol, using lentiviruses (biosafety level-2 agent) and establishment of the germicidal UVC exposure protocol. RESULTS: An average of 4.38x103 PFUml-1(SD 772.68) was recovered from untreated masks while 4.44x102 PFUml-1(SD 203.67), 4.00x102 PFUml-1(SD 115.47), 1.56x102 PFUml-1(SD 76.98) and 4.44x101 PFUml-1(SD 76.98) was recovered in exposures 2s,6s,18s and 54 seconds per side respectively. The germicidal device output and positioning was monitored and a minimum output of 5.43 mWcm-2 was maintained. Infectious SARS-CoV-2 was not detected by plaque assays (minimal level of detection is 67 PFUml-1) on N95 respirator snippets when irradiated for 120s per side or longer suggesting 3.5 log reduction in 240 seconds of irradiation. CONCLUSIONS AND RELEVANCE: A scalable germicidal UVC device to deliver tailored UVC dose for rapid decontamination of SARS-CoV-2 was developed. UVC germicidal irradiation of N95 snippets inoculated with SARS-CoV-2 for 120s per side resulted in 100% (3.5 log in total) reduction of virus. These data support the reuse of N95 particle-filtrate apparatus upon irradiation with UVC and supports use of UVC-based decontamination of SARS-CoV-2 virus during the COVID19 pandemic.

Metastasis Suppressor NME1 Modulates Choice of Double-Strand Break Repair Pathways in Melanoma Cells by Enhancing Alternative NHEJ while Inhibiting NHEJ and HR.

Reduced NME1 expression in melanoma cell lines, mouse models of melanoma, and melanoma specimens in human patients is associated with increased metastatic activity. Herein, we investigate the role of NME1 in repair of double-stranded breaks (DSBs) and choice of double-strand break repair (DSBR) pathways in melanoma cells. Using chromatin immunoprecipitation, NME1 was shown to be recruited rapidly and directly to DSBs generated by the homing endonuclease I-PpoI. NME1 was recruited to DSBs within 30 min, in concert with recruitment of ataxia-telangiectasia mutated (ATM) protein, an early step in DSBR complex formation, as well as loss of histone 2B. NME1 was detected up to 5 kb from the break site after DSB induction, suggesting a role in extending chromatin reorganization away from the repair site. shRNA-mediated silencing of NME1 expression led to increases in the homologous recombination (HR) and non-homologous end-joining (NHEJ) pathways of double-strand break repair (DSBR), and reduction in the low fidelity, alternative-NHEJ (A-NHEJ) pathway. These findings suggest low expression of NME1 drives DSBR towards higher fidelity pathways, conferring enhanced genomic stability necessary for rapid and error-free proliferation in invasive and metastatic cells. The novel mechanism highlighted in the current study appears likely to impact metastatic potential and therapy-resistance in advanced melanoma and other cancers.

Investigation of glycosaminoglycan mimetic scaffolds for neurite growth.

Spinal cord injury can lead to severe dysfunction as a result of limited nerve regeneration that is due to an inhibitory environment created at the site of injury. Neural tissue engineering using materials that closely mimic the extracellular matrix (ECM) during neural development could enhance neural regeneration. Glycosaminoglycans (GAGs), which are sulfated polysaccharides, have been shown to modulate axonal outgrowth in neural tissue depending upon the position and degree of sulfation. Cellulose sulfate (CelS), which is a GAG mimetic, was evaluated for its use in promoting neurite extension. Aligned fibrous scaffolds containing gelatin blended with 0.25% partially sulfated cellulose sulfate (pCelS), having sulfate predominantly at the 6-carbon position of the glucose monomer unit, and fully sulfated cellulose sulfate (fCelS), which is sulfated at the 2-, 3-, and 6-carbon positions of the glucose monomer unit, were fabricated using the electrospinning method. Comparisons were made with scaffolds containing native GAGs, chondroitin sulfate-A (CS-A) and chondroitin sulfate-C (CS-C), which were obtained from commercial sources. CS-A and CS-C are present in neural tissue ECM. The degree of sulfation and position of sulfate groups was determined using elemental analysis, Fourier-transform infrared spectroscopy (FTIR), Raman microspectroscopy, and 13C nuclear magnetic resonance (NMR). In vitro studies examined both nerve growth factor (NGF) binding on scaffolds and neurite extension by dorsal root ganglion (DRG) neurons. NGF binding was highest on scaffolds containing pCelS and fCelS. Neurite extension was greatest for scaffolds containing fCelS followed by pCelS, with the lowest outgrowth on the CS-A containing scaffolds, suggesting that the degree and position of sulfation of CelS was permissible for neurite outgrowth. This study demonstrated that cellulose sulfate, as a GAG mimetic, could be used for future neural tissue regeneration application. STATEMENT OF SIGNFICANCE: Scaffolds that closely mimic the native extracellular matrix (ECM) during development may be a promising approach to enhance neural regeneration. Here, we reported a glycosaminoglycan (GAG) mimetic derived from cellulose that promotes neurite extension over native GAGs, chondroitin sulfate-A (CS-A) and chondroitin sulfate-C (CS-C), which are present in neural ECM. Depending upon the degree and position of sulfation, the GAG mimetic can impact nerve growth factor binding and permissive neurite outgrowth.

* Gelatin Scaffolds Containing Partially Sulfated Cellulose Promote Mesenchymal Stem Cell Chondrogenesis.

Articular cartilage has a limited capacity to heal after damage from injury or degenerative disease. Tissue engineering constructs that more closely mimic the native cartilage microenvironment can be utilized to promote repair. Glycosaminoglycans (GAGs), a major component of the cartilage extracellular matrix, have the ability to sequester growth factors due to their level and spatial distribution of sulfate groups. This study evaluated the use of a GAG mimetic, cellulose sulfate, as a scaffolding material for cartilage tissue engineering. Cellulose sulfate can be synthesized to have a similar level and spatial distribution of sulfates as chondroitin sulfate C (CSC), the naturally occurring GAG. This partially sulfated cellulose (pSC) was incorporated into a fibrous gelatin construct by the electrospinning process. Scaffolds were characterized for fiber morphology and overall stability over time in an aqueous environment, growth factor interaction, and for supporting mesenchymal stem cell (MSC) chondrogenesis in vitro. All scaffold groups had micron-sized fibers and maintained overall stability in aqueous environments. Increasing concentrations of the transforming growth factor-beta 3 (TGF-ß3) were detected on scaffolds with increasing pSC. MSC chondrogenesis was enhanced on the scaffold with the highest pSC concentration as seen with the highest collagen type II production, collagen type II immunostaining, expression of cartilage-specific genes, and ratio of collagen type II to collagen type I production. These studies demonstrated the potential of pSC sulfate as a scaffolding material for cartilage tissue engineering.

Surgical reconstruction of the ossicular chain with custom 3D printed ossicular prosthesis.

BACKGROUND: Conductive hearing loss due to ossicular abnormalities occurs from many causes, including trauma, infection, cholesteatoma, surgery and congenital anomalies. Surgical reconstruction of the ossicular chain is a well-established procedure for repair of ossicular defects, but is still plagued by high failure rates. Underlying disease and proper sizing of prostheses are two challenges that lead to component failure. Three-dimensional (3D) printing has been used successfully to solve a number of medical prosthesis problems. Custom 3D printing an individualized ossicular prosthesis would be a potential solution for the wide range of anatomic variation encountered in the pathological middle ear, and could decrease the rate of post-operative prosthesis displacement by increasing the likelihood of a proper fit, in addition to decreasing surgical time.In this study, the incus was removed from three formalin-fixed cadaveric human temporal bones with no macro- or microscopic evidence of pathology. Imaging of the cadaveric bone was obtained using a standard temporal bone CT protocol. A custom prosthesis for each cadaveric human temporal bone was designed using the Mimics Innovation Suite software (Materialise, Belgium) and fabricated on a Form2 3D printer (FormLabs, Somerville, Massachusetts). Four surgeons then performed insertion of each prosthesis into each middle ear, blinded to the bone from and for which each was designed. The surgeons were asked to match each prosthesis to its correct parent bone. RESULTS: Each prosthesis had unique measurements. Each of the four surgeons was able to correctly match the prosthesis model to its intended temporal bone. The chances of this occurring randomly are 1:1296. CONCLUSIONS: A custom 3D printed ossicular prosthesis is a viable solution for conductive hearing loss due to ossicular chain defects. Commercially available CT scanners can detect significant anatomic differences in normal human middle ear ossicles. These differences can be accurately represented with current 3D printing technology and, more significantly, surgeons can detect these differences.

Local Zinc Chloride Release From a Calcium Sulfate Carrier Enhances Fracture Healing.

BACKGROUND: This study examined the efficacy of calcium sulfate (CaSO4) as a carrier for intramedullary delivery of zinc chloride (ZnCl2) to treat fracture healing in a BB Wistar rat model. A non-carrier-mediated injection of 3.0 mg/kg of ZnCl2 has previously been shown to enhance fracture healing. METHODS: A heterogeneous mixture of ZnCl2 and CaSO4 was administered into the intramedullary femoral canal and a mid-diaphyseal femur fracture was created unilaterally. Early and late parameters of fracture healing were assessed using biomechanical testing, radiographic scoring, quantitative histomorphometry (for percentage of new cartilage and bone within the fracture callus), and long-term histologic evaluation. RESULTS: Fractures treated with 1.0 mg/kg of ZnCl2/CaSO4 demonstrated a significantly higher maximum torque to failure compared with both CaSO4 (P = 0.048) and saline (P = 0.005) controls at 4 weeks postfracture (396.4 versus 251.3 versus 178.7 N mm, respectively). Statistically significant increases in torsional rigidity, effective shear modulus, and effective shear stress were also found, as well as a 3.5 times increase in radiographic score (based on bone union). Histologic examination of the fracture callus indicated enhanced chondrogenesis at day 14 postfracture, with increased percent cartilage for the ZnCl2/CaSO4 group compared with saline (P = 0.0004) and CaSO4 (P = 0.0453) controls. Long-term radiographic and histologic evaluation revealed no abnormal bone formation or infection up to 12 weeks postoperatively. CONCLUSIONS: The effective dose of ZnCl2 augmentation for the enhancement of fracture healing in rats was reduced 3-fold in this study compared with previous findings. Furthermore, CaSO4 acted synergistically with ZnCl2 to increase the mechanical strength and stability at the fracture site.

Numerical Modeling of Indoor Environment with a Ceiling Fan and an Upper-Room Ultraviolet Germicidal Irradiation System.

This study proposes a numerical modeling method for the indoor environment with ceiling fans and upper-room ultraviolet germicidal irradiation (UR-UVGI) fixtures. The numerical modeling deployed steady-state Computational Fluid Dynamics (CFD) with a rotating reference frame to simulate the rotation of fan blades. CFD was validated with experimental data of velocity field and fraction of microorganism remaining at the exhaust diffuser. The fraction of microorganism remaining represented the ratio of the concentration of airborne microorganisms measured with UVGI turned on to the one measured with UVGI turned off. According to the validation results, the CFD model correctly reproduced the air movement induced by the rotation of ceiling fan. When the ambient ventilation rate was 2 ACH (air changes per hour) or 6 ACH, the CFD model accurately predicted the average vertical speeds in the section 2.44 m above the floor with the errors less than 10%, regardless of the ceiling fan's rotational direction or speed. In addition, the simulation results showed that the fraction of microorganism remaining increased with the ambient air exchange rate when the fan blew air downward with a rotational speed as high as 235 rpm, which corresponded with the experimental results. Furthermore, the simulation results accurately predicted the fraction of microorganism remaining when the ambient air exchange rate was 2 ACH. We conclude that this novel numerical model can reproduce the effects of ceiling fans and UR-UVGI fixtures on indoor environment, and should aid in the investigation of the impact of ceiling fans on UR-UVGI disinfection efficacy.

Upper-room ultraviolet germicidal irradiation (UVGI) for air disinfection: a symposium in print.

Upper-room ultraviolet germicidal irradiation (UVGI) has several applications, its most important use is to reduce tuberculosis transmission in high-burden, resource-limited settings, especially those dealing with epidemics of drug-resistant disease. The efficacy of upper-room (UVGI) to reduce the transmission of airborne infection in real-world settings is no longer in question. International application (dosing) guidelines are needed, as are safety standards and commissioning procedures. A recent symposium to build consensus on guidelines discussed specifications for affordable UVGI fixture designs, safety, performance, computer-aided design (CAD) for UVGI, maintenance, dosimetry, gonioradiometric measurement and innovation using germicidal LEDs.

Ultraviolet germicidal irradiation safety concerns: a lesson from the Tuberculosis Ultraviolet Shelter Study: Murphy's Law affirmed.

Concerns about the safety of Ultraviolet Germicidal Irradiation (UVGI) applications on human beings have been an issue at least since the introduction of this technology for practical use in the 1930s. The resurgence of tuberculosis (TB) in the United States in the mid-1980s led to a revival of interest in UV technology, a focus that had almost disappeared because alternate means of controlling TB had inaccurately been deemed successful. These failures in TB control led to a revival of UVGI use. And with that revival grew necessary and appropriate concerns about attempts to eliminate human overexposure. For all those working in the field of UVGI, safety issues must be a concern because when UVGI fixtures are placed improperly, or precautions ignored, room occupants are placed at risk of photokeratoconjunctivitis and photodermatitis. If safety is so prominent a concern, why do incidents of UV side effects continue to occur? See Murphy's Law.

Numerical investigation of upper-room UVGI disinfection efficacy in an environmental chamber with a ceiling fan.

This study investigated the disinfection efficacy of the upper-room ultraviolet germicidal irradiation (UR-UVGI) system with ceiling fans. The investigation used the steady-state computational fluid dynamics (CFD) simulations to solve the rotation of ceiling fan with a rotating reference frame. Two ambient air exchange rates, 2 and 6 air changes per hour (ACH), and four downward fan rotational speeds, 0, 80, 150 and 235 rpm were considered. In addition, the passive scalar concentration simulations incorporated ultraviolet (UV) dose by two methods: one based on the total exposure time and average UV fluence rate, and another based on SVE3* (New Scale for Ventilation Efficiency 3), originally defined to evaluate the mean age of the air from an air supply opening. Overall, the CFD results enabled the evaluation of UR-UVGI disinfection efficacy using different indices, including the fraction of remaining microorganisms, equivalent air exchange rate, UR-UVGI effectiveness and tuberculosis infection probability by the Wells-Riley equation. The results indicated that air exchange rate was the decisive factor for determining UR-UVGI performance in disinfecting indoor air. Using a ceiling fan could also improve the performance in general. Furthermore, the results clarified the mechanism for the ceiling fan to influence UR-UVGI disinfection efficacy.

A radiometry protocol for UVGI fixtures using a moving-mirror type gonioradiometer.

Ultraviolet germicidal irradiation (UVGI), 254 nm UV-C, is increasingly used as an infection control strategy to reduce the spread of airborne pathogens such as tuberculosis (TB), influenza viruses, and measles. With the appearance of multidrug-resistant TB and emerging infectious disease such as severe acute respiratory syndrome (SARS) and H1N1 influenza viruses, engineering controls using 254 nm UV-C lamps within specialized luminaires, herein designated UVGI fixtures, are being installed in high-risk settings such as homeless shelters, hospitals, jails and prisons, and schools. Studies have established that a relatively uniform spatial distribution of UV-C in the upper room can effectively cleanse the air of aerosolized pathogens. However, for planning purposes, the placement of multiple UVGI fixtures in a space, to achieve uniformity of UV-C energy distribution using currently available lighting software, is not yet practical because no industry-wide standard method exists for radiometric measurement of commercial UVGI fixtures. In this article, standard methods for photometry and reporting of general fluorescent lighting luminaire photometric data are adopted to provide UVGI fixture spatial emission distribution data in an electronic file format. The ultimate expectation of the authors is that the results will lead to a software program for fixture placement, comparable to and as easy to use as the corresponding software used for general interior lighting applications. To accomplish this goal, a radiometry measurement system is developed to obtain the radiant intensity distributions of UVGI fixtures in a three-dimensional space. This system includes a moving-mirror Type C goniometer, a mirror, a radiometer, a desktop computer, the mechanical control hardware, and the data acquisition/presentation software. Repeated measurements were made on each of three exemplary UVGI fixtures, and measurement variation did not exceed ± 2.0%.

Mobile Medical Education (MoMEd) - how mobile information resources contribute to learning for undergraduate clinical students - a mixed methods study.

BACKGROUND: Mobile technology is increasingly being used by clinicians to access up-to-date information for patient care. These offer learning opportunities in the clinical setting for medical students but the underlying pedagogic theories are not clear. A conceptual framework is needed to understand these further. Our initial questions were how the medical students used the technology, how it enabled them to learn and what theoretical underpinning supported the learning. METHODS: 387 medical students were provided with a personal digital assistant (PDA) loaded with medical resources for the duration of their clinical studies. Outcomes were assessed by a mixed-methods triangulation approach using qualitative and quantitative analysis of surveys, focus groups and usage tracking data. RESULTS: Learning occurred in context with timely access to key facts and through consolidation of knowledge via repetition. The PDA was an important addition to the learning ecology rather than a replacement. Contextual factors impacted on use both positively and negatively. Barriers included concerns of interrupting the clinical interaction and of negative responses from teachers and patients. Students preferred a future involving smartphone platforms. CONCLUSIONS: This is the first study to describe the learning ecology and pedagogic basis behind the use of mobile learning technologies in a large cohort of undergraduate medical students in the clinical environment. We have developed a model for mobile learning in the clinical setting that shows how different theories contribute to its use taking into account positive and negative contextual factors.The lessons from this study are transferable internationally, to other health care professions and to the development of similar initiatives with newer technology such as smartphones or tablet computers.