Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 20 de 36
Filtrar
Mais filtros








Base de dados
Intervalo de ano de publicação
1.
Small Methods ; 7(9): e2300170, 2023 09.
Artigo em Inglês | MEDLINE | ID: mdl-37154264

RESUMO

Wearable flexible strain sensors with spatial resolution enable the acquisition and analysis of complex actions for noninvasive personalized healthcare applications. To provide secure contact with skin and to avoid environmental pollution after usage, sensors with biocompatibility and biodegradability are highly desirable. Herein, wearable flexible strain sensors composed of crosslinked gold nanoparticle (GNP) thin films as the active conductive layer and transparent biodegradable polyurethane (PU) films as the flexible substrate are developed. The patterned GNP films (micrometer- to millimeter-scale square and rectangle geometry, alphabetic characters, and wave and array patterns) are transferred onto the biodegradable PU film via a facile, clean, rapid and high-precision contact printing method, without the need of a sacrificial polymer carrier or organic solvents. The GNP-PU strain sensor with low Young's modulus (≈17.8 MPa) and high stretchability showed good stability and durability (10 000 cycles) as well as degradability (42% weight loss after 17 days at 74 °C in water). The GNP-PU strain sensor arrays with spatiotemporal strain resolution are applied as wearable eco-friendly electronics for monitoring subtle physiological signals (e.g., mapping of arterial lines and sensing pulse waveforms) and large-strain actions (e.g., finger bending).


Assuntos
Nanopartículas Metálicas , Dispositivos Eletrônicos Vestíveis , Ouro , Pele , Atenção à Saúde
2.
Nanoscale ; 15(9): 4506-4514, 2023 Mar 02.
Artigo em Inglês | MEDLINE | ID: mdl-36753337

RESUMO

We demonstrate that oleyl phosphate ligand-stabilized iron oxide nanocubes as building blocks can be assembled into 2D supercrystalline mono- and multilayers on flat YSZ substrates within a few minutes using a simple spin-coating process. As a bottom-up process, the growth takes place in a layer-by-layer mode and therefore by tuning the spin-coating parameters, the exact number of deposited monolayers can be controlled. Furthermore, ex situ scanning electron and atomic force microscopy as well as X-ray reflectivity measurements give evidence that the choice of solvent allows the control of the lattice type of the final supercrystalline monolayers. This observation can be assigned to the different Hansen solubilities of the solvents used for the nanoparticle dispersion because it determines the size and morphology of the ligand shell surrounding the nanoparticle core. Here, by using toluene and chloroform as solvents, it can be controlled whether the resulting monolayers are ordered in a square or hexagonal supercrystalline lattice.

3.
ACS Nano ; 16(8): 11692-11707, 2022 Aug 23.
Artigo em Inglês | MEDLINE | ID: mdl-35760395

RESUMO

Nanocrystal assembly into ordered structures provides mesostructural functional materials with a precise control that starts at the atomic scale. However, the lack of understanding on the self-assembly itself plus the poor structural integrity of the resulting supercrystalline materials still limits their application into engineered materials and devices. Surface functionalization of the nanobuilding blocks with organic ligands can be used not only as a means to control the interparticle interactions during self-assembly but also as a reactive platform to further strengthen the final material via ligand cross-linking. Here, we explore the influence of the ligands on superlattice formation and during cross-linking via thermal annealing. We elucidate the effect of the surface functionalization on the nanostructure during self-assembly and show how the ligand-promoted superlattice changes subsequently alter the cross-linking behavior. By gaining further insights on the chemical species derived from the thermally activated cross-linking and its effect in the overall mechanical response, we identify an oxidative radical polymerization as the main mechanism responsible for the ligand cross-linking. In the cascade of reactions occurring during the surface-ligands polymerization, the nanocrystal core material plays a catalytic role, being strongly affected by the anchoring group of the surface ligands. Ultimately, we demonstrate how the found mechanistic insights can be used to adjust the mechanical and nanostructural properties of the obtained nanocomposites. These results enable engineering supercrystalline nanocomposites with improved cohesion while preserving their characteristic nanostructure, which is required to achieve the collective properties for broad functional applications.

4.
Langmuir ; 37(32): 9851-9857, 2021 Aug 17.
Artigo em Inglês | MEDLINE | ID: mdl-34343009

RESUMO

This work presents a facile one-step protocol for the gram-scale synthesis of iron oxide nanocubes with adjustable sizes ranging from 13 to 20 nm and with size distributions between 7 and 12%. As X-ray diffraction indicated the initial formation of the wüstite phase, a formation mechanism of the nanocubes based on the wüstite crystal structure is proposed. When exposed to ambient conditions, the nanoparticles rapidly oxidize to magnetite/maghemite with a remaining wüstite core. The cubic morphology is attributed to the thermodynamic stability of the exposed {100} facets and the control over the growth rate via the use of a sodium oleate/oleic acid mixed ligand system. In contrast to previously reported procedures, the described synthetic approach does not require the initial preparation and isolation of iron oleate. Therefore, the amount of work and the consumption of hazardous solvents are significantly reduced. Thus, the method presented is much more efficient and environmentally more friendly while maintaining excellent control over the particles' shape, size, and size distribution.

5.
ACS Appl Mater Interfaces ; 13(34): 40932-40941, 2021 Sep 01.
Artigo em Inglês | MEDLINE | ID: mdl-34415725

RESUMO

Freestanding nanoassemblies represent a new class of functional materials with highly responsive optical, electrical, and mechanical properties. Hence, they are well-suited for applications in advanced sensor devices. Here, it is shown that transfer printing enables the well-controlled fabrication of freestanding membranes from layered nanoassemblies: Using a polydimethylsiloxane (PDMS) stamp, thin films (thickness: ∼45 to ∼51 nm) of 1,6-hexanedithiol cross-linked gold nanoparticles (diameter: ∼3.9 ± 0.8 nm) were transferred onto surface-oxidized silicon substrates featuring square microcavities with edge lengths of ∼78 µm. After adjusting the contact pressure to 1.8 bar, intact membranes were printed in yields of ∼70%. The prestress of printed membranes was determined by measuring their resonance frequencies under electrostatic actuation. In general, the prestress values were in the ∼10 MPa range with standard deviations below 10% for parallel printed resonators. The deviations in average prestress between resonators printed onto different substrates were 21% or less. By increasing the temperature during the final transfer step from 5 to 48 °C, it was possible to tune the average prestress from ∼14 to ∼28 MPa. This effect was attributed to the pronounced thermal expansion of the PDMS stamp. Finally, by transfer printing layered films of graphene oxide/silk fibroin (GO/SF), it is shown that the approach can be adapted for the fabrication of freestanding membranes from very different nanomaterials.

6.
Molecules ; 25(20)2020 Oct 19.
Artigo em Inglês | MEDLINE | ID: mdl-33086563

RESUMO

Multiscale ceramic-organic supercrystalline nanocomposites with two levels of hierarchy have been developed via self-assembly with tailored content of the organic phase. These nanocomposites consist of organically functionalized ceramic nanoparticles forming supercrystalline micron-sized grains, which are in turn embedded in an organic-rich matrix. By applying an additional heat treatment step at mild temperatures (250-350 °C), the mechanical properties of the hierarchical nanocomposites are here enhanced. The heat treatment leads to partial removal and crosslinking of the organic phase, minimizing the volume occupied by the nanocomposites' soft phase and triggering the formation of covalent bonds through the organic ligands interfacing the ceramic nanoparticles. Elastic modulus and hardness up to 45 and 2.5 GPa are attained, while the hierarchical microstructure is preserved. The presence of an organic phase between the supercrystalline grains provides a toughening effect, by curbing indentation-induced cracks. A mapping of the nanocomposites' mechanical properties reveals the presence of multiple microstructural features and how they evolve with heat treatment temperature. A comparison with non-hierarchical, homogeneous supercrystalline nanocomposites with lower organic content confirms how the hierarchy-inducing organic excess results in toughening, while maintaining the beneficial effects of crosslinking on the materials' stiffness and hardness.


Assuntos
Cerâmica/química , Fenômenos Mecânicos , Nanocompostos/química , Zircônio/química , Módulo de Elasticidade , Dureza , Teste de Materiais , Temperatura
7.
Nanomaterials (Basel) ; 10(6)2020 Jun 19.
Artigo em Inglês | MEDLINE | ID: mdl-32575397

RESUMO

Metal-ceramic composite particles are of increasing interest due to their potential applications in photonic metamaterials as well as next-generation catalysts. The zirconia-gold system has received little attention due to the lack of controllable preparation methods. Well-known methods for the deposition of gold nanoshells on silica spheres, however, should be adaptable for similar zirconia-based materials. Here, we present a novel synthetic approach to the well-controlled deposition of gold on the surface of sol-gel derived zirconia mesoparticles by a stepwise method involving the immobilization of gold nanoparticles and repeated seeded-growth steps. We show that the immobilization efficiency is strongly enhanced by acidification with hydrochloric acid and additional employment of aminomethylphosphonic acid as coupling agent. The optimum conditions are identified and the subsequent incremental growth by seeded reduction of gold is demonstrated. The results shed light on the parameters governing the preparation of zirconia@gold composite particles and our synthetic approach provides a promising tool for future developments in complex nanomaterials design.

8.
Langmuir ; 35(43): 13893-13903, 2019 Oct 29.
Artigo em Inglês | MEDLINE | ID: mdl-31580678

RESUMO

Supercrystalline nanocomposite materials with micromechanical properties approaching those of nacre or similar structural biomaterials can be produced by self-assembly of organically modified nanoparticles and further strengthened by cross-linking. The strengthening of these nanocomposites is controlled via thermal treatment, which promotes the formation of covalent bonds between interdigitated ligands on the nanoparticle surface. In this work, it is shown how the extent of the mechanical properties enhancement can be controlled by the solvent used during the self-assembly step. We find that the resulting mechanical properties correlate with the Hansen solubility parameters of the solvents and ligands used for the supercrystal assembly: the hardness and elastic modulus decrease as the Hansen solubility parameter of the solvent approaches the Hansen solubility parameter of the ligands that stabilize the nanoparticles. Moreover, it is shown that self-assembled supercrystals that are subsequently uniaxially pressed can deform up to 6 %. The extent of this deformation is also closely related to the solvent used during the self-assembly step. These results indicate that the conformation and arrangement of the organic ligands on the nanoparticle surface not only control the self-assembly itself but also influence the mechanical properties of the resulting supercrystalline material. The Hansen solubility parameters may therefore serve as a tool to predict what solvents and ligands should be used to obtain supercrystalline materials with good mechanical properties.

9.
Materials (Basel) ; 12(18)2019 Sep 05.
Artigo em Inglês | MEDLINE | ID: mdl-31491844

RESUMO

Zirconia nanoceramics are interesting materials for numerous high-temperature applications. Because their beneficial properties are mainly governed by the crystal and microstructure, it is essential to understand and control these features. The use of co-stabilizing agents in the sol-gel synthesis of zirconia submicro-particles should provide an effective tool for adjusting the particles' size and shape. Furthermore, alumina-doping is expected to enhance the particles' size and shape persistence at high temperatures, similar to what is observed in corresponding bulk ceramics. Dispersed alumina should inhibit grain growth by forming diffusion barriers, additionally impeding the martensitic phase transformation in zirconia grains. Here, alumina-doped zirconia particles with sphere-like shape and average diameters of ∼ 300 n m were synthesized using a modified sol-gel route employing icosanoic acid and hydroxypropyl cellulose as stabilizing agents. The particles were annealed at temperatures between 800 and 1200 ∘ C and characterized by electron microscopy, elemental analysis, and X-ray diffraction. Complementary elemental analyses confirmed the precise control over the alumina content (0-50 mol%) in the final product. Annealed alumina-doped particles showed more pronounced shape persistence after annealing at 1000 ∘ C than undoped particles. Quantitative phase analyses revealed an increased stabilization of the tetragonal/cubic zirconia phase and a reduced grain growth with increasing alumina content. Elemental mapping indicated pronounced alumina segregation near the grain boundaries during annealing.

10.
Nanomaterials (Basel) ; 9(9)2019 Aug 29.
Artigo em Inglês | MEDLINE | ID: mdl-31470667

RESUMO

In order to enable advanced technological applications of nanocrystal composites, e.g., as functional coatings and layers in flexible optics and electronics, it is necessary to understand and control their mechanical properties. The objective of this study was to show how the elasticity of such composites depends on the nanocrystals' dimensionality. To this end, thin films of titania nanodots (TNDs; diameter: ~3-7 nm), nanorods (TNRs; diameter: ~3.4 nm; length: ~29 nm), and nanoplates (TNPs; thickness: ~6 nm; edge length: ~34 nm) were assembled via layer-by-layer spin-coating. 1,12-dodecanedioic acid (12DAC) was added to cross-link the nanocrystals and to enable regular film deposition. The optical attenuation coefficients of the films were determined by ultraviolet/visible (UV/vis) absorbance measurements, revealing much lower values than those known for titania films prepared via chemical vapor deposition (CVD). Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images showed a homogeneous coverage of the substrates on the µm-scale but a highly disordered arrangement of nanocrystals on the nm-scale. X-ray photoelectron spectroscopy (XPS) analyses confirmed the presence of the 12DAC cross-linker after film fabrication. After transferring the films onto silicon substrates featuring circular apertures (diameter: 32-111 µm), freestanding membranes (thickness: 20-42 nm) were obtained and subjected to atomic force microscopy bulge tests (AFM-bulge tests). These measurements revealed increasing elastic moduli with increasing dimensionality of the nanocrystals, i.e., 2.57 ± 0.18 GPa for the TND films, 5.22 ± 0.39 GPa for the TNR films, and 7.21 ± 1.04 GPa for the TNP films.

11.
Langmuir ; 35(26): 8790-8798, 2019 Jul 02.
Artigo em Inglês | MEDLINE | ID: mdl-31244257

RESUMO

Most applications of nanoparticles require robust stabilization, for example, by surface-bound ligands or the encapsulation within polymer shells. Furthermore, for biomedical applications, the particles must be dispersible in a complex biological environment. Thus, high-quality nanoparticles synthesized in organic solvents must be transferred into aqueous media. Here, we present a novel scalable method enabling the robust hydrophilic encapsulation of non-agglomerated nanoparticles by growing polystyrene shells via AGET-ATRP in microemulsion. To demonstrate this approach, we encapsulate iron oxide nanoparticles (diameter: 13.7 ± 0.6 nm). Because the ATRP initiator is grafted onto the nanoparticles' surface, the shells are covalently attached to the iron oxide cores. By varying the amount of monomers, the shell thickness can be adjusted precisely, as indicated by the increasing hydrodynamic size from ∼22 to 26 nm (DLS, number mean) with an increasing amount of added monomers. Moreover, the degree of cross-linking can be controlled by the amount of added divinylbenzene (DVB). To evaluate the robustness of the polymer shells against ion infusion, we introduce a novel colorimetric method, which is based on the formation of the red iron thiocyanate complex. After addition of HCl, the increase in absorbance at 468 nm indicates leaching of iron ions from the polymer-encapsulated core particles. These measurements confirm that with increasing shell thickness, significantly improved shielding is achieved. Furthermore, high concentrations of added DVB [33-50% (v/v) in a monomer mixture] improve the shielding effect. However, when smaller amounts of DVB were added [10-25% (v/v)], the shielding effect was diminished, even in comparison to non-cross-linked polymer shells. This finding suggests a higher porosity of shells with a low degree of cross-linking.

12.
Sci Rep ; 9(1): 3435, 2019 03 05.
Artigo em Inglês | MEDLINE | ID: mdl-30837545

RESUMO

Biomaterials often display outstanding combinations of mechanical properties thanks to their hierarchical structuring, which occurs through a dynamically and biologically controlled growth and self-assembly of their main constituents, typically mineral and protein. However, it is still challenging to obtain this ordered multiscale structural organization in synthetic 3D-nanocomposite materials. Herein, we report a new bottom-up approach for the synthesis of macroscale hierarchical nanocomposite materials in a single step. By controlling the content of organic phase during the self-assembly of monodisperse organically-modified nanoparticles (iron oxide with oleyl phosphate), either purely supercrystalline or hierarchically structured supercrystalline nanocomposite materials are obtained. Beyond a critical concentration of organic phase, a hierarchical material is consistently formed. In such a hierarchical material, individual organically-modified ceramic nanoparticles (Level 0) self-assemble into supercrystals in face-centered cubic superlattices (Level 1), which in turn form granules of up to hundreds of micrometers (Level 2). These micrometric granules are the constituents of the final mm-sized material. This approach demonstrates that the local concentration of organic phase and nano-building blocks during self-assembly controls the final material's microstructure, and thus enables the fine-tuning of inorganic-organic nanocomposites' mechanical behavior, paving the way towards the design of novel high-performance structural materials.

13.
Langmuir ; 35(9): 3256-3264, 2019 Mar 05.
Artigo em Inglês | MEDLINE | ID: mdl-30607954

RESUMO

In this study, a highly responsive humidity sensor is developed by printing gold nanoparticles (GNPs) grafted with a hygroscopic polymer. These GNPs are inkjet-printed to form a uniform thin film over an interdigitated electrode with a controllable thickness by adjusting the printing parameters. The resistance of the printed GNP thin film decreases significantly upon exposure to water vapor and exhibits a semi-log relationship with relative humidity (RH). The sensor can detect RH variations from 1.8 to 95% with large resistance changes up to 4 orders of magnitude with no hysteresis and small temperature dependence. In addition, with a small thickness, the sensor can reach absorption equilibrium quickly with response and recovery times of ≤1.2 and ≤3 s, respectively. The fast response to humidity changes also allows the GNP thin-film sensor to distinguish signals from intermittent humidification/dehumidification cycles with a frequency up to 2.5 Hz. The printed sensors on flexible substrates show little sensitivity to bending deformation and can be embedded in a mask for human respiratory detection. In summary, this study demonstrates the feasibility of applying printing technology for the fabrication of thin-film humidity sensors, and the methodology developed can be further applied to fabricate many other types of nanoparticle-based sensor devices.

14.
RSC Adv ; 9(46): 26902-26914, 2019 Aug 23.
Artigo em Inglês | MEDLINE | ID: mdl-35528597

RESUMO

ZrO2@SiO2 core-shell submicron particles are promising candidates for the development of advanced optical materials. Here, submicron zirconia particles were synthesized using a modified sol-gel method and pre-calcined at 400 °C. Silica shells were grown on these particles (average size: ∼270 nm) with well-defined thicknesses (26 to 61 nm) using a seeded-growth Stöber approach. To study the thermal stability of bare ZrO2 cores and ZrO2@SiO2 core-shell particles they were calcined at 450 to 1200 °C. After heat treatments, the particles were characterized by SEM, TEM, STEM, cross-sectional EDX mapping, and XRD. The non-encapsulated, bare ZrO2 particles predominantly transitioned to the tetragonal phase after pre-calcination at 400 °C. Increasing the temperature to 600 °C transformed them to monoclinic. Finally, grain coarsening destroyed the spheroidal particle shape after heating to 800 °C. In striking contrast, SiO2-encapsulation significantly inhibited grain growth and the t → m transition progressed considerably only after heating to 1000 °C, whereupon the particle shape, with a smooth silica shell, remained stable. Particle disintegration was observed after heating to 1200 °C. Thus, ZrO2@SiO2 core-shell particles are suited for high-temperature applications up to ∼1000 °C. Different mechanisms are considered to explain the markedly enhanced stability of ZrO2@SiO2 core-shell particles.

15.
ACS Appl Mater Interfaces ; 10(43): 37374-37385, 2018 Oct 31.
Artigo em Inglês | MEDLINE | ID: mdl-30280559

RESUMO

In this study, we developed a novel and efficient process for the fabrication of resistive strain gauges for healthcare-related applications. First, 1,9-nonanedithiol cross-linked gold nanoparticle (GNP) films were prepared via layer-by-layer (LbL) spin-coating and subsequently transferred onto flexible polyimide foil by contact printing. Four-point bending tests revealed linear response characteristics with gauge factors of ∼14 for 4 nm GNPs and ∼26 for 7 nm GNPs. This dependency of strain sensitivity is attributed to the perturbation of charge carrier tunneling between neighboring GNPs, which becomes more efficient with increasing particle size. Fatigue tests revealed that the strain-resistance performance remained nearly the same after 10.000 strain/relaxation cycles. We demonstrate that these sensors are well suited to monitor muscle movements. Furthermore, we fabricated all-printed strain sensors by directly transferring cross-linked GNP films onto soft PDMS sheets equipped with interdigitated electrodes. Due to the low elastic modulus of poly(dimethylsiloxane) (PDMS), these sensors are easily deformed and, therefore, they respond sensitively to faint forces. When taped onto the skin above the radial artery, they enable the well-resolved and robust recording of pulse waves with diagnostically relevant details.


Assuntos
Técnicas Biossensoriais , Ouro/química , Nanopartículas Metálicas/química , Impressão , Reagentes de Ligações Cruzadas/química , Dimetilpolisiloxanos/química , Eletrodos , Desenho de Equipamento , Humanos , Teste de Materiais , Microscopia Eletrônica de Transmissão , Músculo Esquelético/fisiopatologia , Tamanho da Partícula
16.
ACS Sens ; 2(4): 540-546, 2017 Apr 28.
Artigo em Inglês | MEDLINE | ID: mdl-28723182

RESUMO

We report a novel approach for the detection of volatile compounds employing electrostatically driven drumhead resonators as sensing elements. The resonators are based on freestanding membranes of alkanedithiol cross-linked gold nanoparticles (GNPs), which are able to sorb analytes from the gas phase. Under reduced pressure, the fundamental resonance frequency of a resonator is continuously monitored while the device is exposed to varying partial pressures of toluene, 4-methylpentan-2-one, 1-propanol, and water. The measurements reveal a strong, reversible frequency shift of up to ∼10 kHz, i.e., ∼5% of the fundamental resonance frequency, when exposing the sensor to toluene vapor with a partial pressure of ∼20 Pa. As this strong shift cannot be explained exclusively by the mass uptake in the membrane, our results suggest a significant impact of analyte sorption on the pre-stress of the freestanding GNP membrane. Thus, our findings point to the possibility of designing highly sensitive resonators, which utilize sorption induced changes in the membrane's pre-stress as primary transduction mechanism.

17.
J Synchrotron Radiat ; 23(Pt 6): 1440-1446, 2016 11 01.
Artigo em Inglês | MEDLINE | ID: mdl-27787250

RESUMO

Photonic glass is a material class that can be used as photonic broadband reflectors, for example in the infrared regime as thermal barrier coating films. Photonic properties such as the reflectivity depend on the ordering and material packing fraction over the complete film thickness of up to 100 µm. Nanotomography allows acquiring these key parameters throughout the sample volume at the required resolution in a non-destructive way. By performing a nanotomography measurement at the PETRA III beamline P05 on a photonic glass film, the packing fraction throughout the complete sample thickness was analyzed. The results showed a packing fraction significantly smaller than the expected random close packing giving important information for improving the fabrication and processing methods of photonic glass material in the future.

18.
Langmuir ; 32(31): 7897-907, 2016 08 09.
Artigo em Inglês | MEDLINE | ID: mdl-27458652

RESUMO

The use of mixed ligand layers including poly(ethylene glycol)-based ligands for the functionalization of nanoparticles is a very popular strategy in the context of nanomedicine. However, it is challenging to control the composition of the ligand layer and maintain high colloidal and chemical stability of the conjugates. A high level of control and stability are crucial for reproducibility, upscaling, and safe application. In this study, gold nanoparticles with well-defined mixed ligand layers of α-methoxypoly(ethylene glycol)-ω-(11-mercaptoundecanoate) (PEGMUA) and 11-mercaptoundecanoic acid (MUA) were synthesized and characterized by ATR-FTIR spectroscopy and gel electrophoresis. The colloidal and chemical stability of the conjugates was tested by dynamic light scattering (DLS), small-angle X-ray scattering (SAXS), and UV/vis spectroscopy based experiments, and their interactions with cells were analyzed by elemental analysis. We demonstrate that the alkylene spacer in PEGMUA is the key feature for the controlled synthesis of mixed layer conjugates with very high colloidal and chemical stability and that a controlled synthesis is not possible using regular PEG ligands without the alkylene spacer. With the results of our stability tests, the molecular structure of the ligands can be clearly linked to the colloidal and chemical stabilization. We expect that the underlying design principle can be generalized to improve the level of control in nanoparticle surface chemistry.

19.
Nanoscale ; 8(35): 15880-7, 2016 Sep 21.
Artigo em Inglês | MEDLINE | ID: mdl-27471074

RESUMO

Freestanding, nanometer-thin membranes of alkanedithiol cross-linked gold nanoparticles represent elastic, mechanically robust and electrically conductive materials, which are interesting for the fabrication of novel nano- and microelectromechanical devices. In this work we present the first electrostatically driven drumhead resonators based on such nanoparticle membranes. These circular membranes have a thickness of 33 to 52 nm, a diameter of either 50 µm or 100 µm, and are equally spaced from their back electrode by ∼10 µm. Using an interferometric nanovibration analyzer various vibrational modes with resonance amplitudes of up to several 100 nm could be detected when the membranes are excited by applying AC voltages (<30 V) with drive frequencies of up to 2 MHz. Further, spatial amplitude distributions of different vibrational modes could be imaged. The devices showed fundamental resonance frequencies in the high kHz range and quality factors Q up to ∼2000. Finally, vibrational spectra and observed mode patterns could be well interpreted using the theory for a clamped circular membrane with negligible bending stiffness. Our findings mark an important step towards the integration of freestanding gold nanoparticle composite membranes into electromechanical devices with various applications, such as novel types of pressure or mass sensors.

20.
Langmuir ; 32(3): 848-57, 2016 Jan 26.
Artigo em Inglês | MEDLINE | ID: mdl-26731341

RESUMO

Metallodielectric nanostructured core-shell-shell particles are particularly desirable for enabling novel types of optical components, including narrow-band absorbers, narrow-band photodetectors, and thermal emitters, as well as new types of sensors and catalysts. Here, we present a facile approach for the preparation of submicron SiO2@Pt@SiO2 core-shell-shell particles. As shown by transmission and scanning electron microscopy, the first steps of this approach allow for the deposition of closed and almost perfectly smooth platinum shells onto silica cores via a seeded growth mechanism. By choosing appropriate conditions, the shell thickness could be adjusted precisely, ranging from ∼3 to ∼32 nm. As determined by X-ray diffraction, the crystalline domain sizes of the polycrystalline metal shells were ∼4 nm, regardless of the shell thickness. The platinum content of the particles was determined by atomic absorption spectroscopy and for thin shells consistent with a dense metal layer of the TEM-measured thickness. In addition, we show that the roughness of the platinum shell strongly depends on the storage time of the gold seeds used to initiate reductive platinum deposition. Further, using polyvinylpyrrolidone as adhesion layer, it was possible to coat the metallic shells with very homogeneous and smooth insulating silica shells of well-controlled thicknesses between ∼2 and ∼43 nm. After depositing the particles onto silicon substrates equipped with interdigitated electrode structures, the metallic character of the SiO2@Pt particles and the insulating character of the SiO2 shells of the SiO2@Pt@SiO2 particles were successfully demonstrated by charge transport measurements at variable temperatures.

SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA