Advancing PFAS characterization: Development and optimization of a UV-H2O2-TOP assay for improved PFCA chain length preservation and organic matter tolerance.

As per- and polyfluoroalkyl substances (PFAS) infiltrate the environment via industrial, commercial, and domestic sources, the demand for robust, cost-effective, and straightforward analytical assays intensifies to enhance PFAS characterization and quantification. To address this demand, this study introduces a novel UV-H2O2-TOP assay, identifying optimal parameters such as pH (5-9), oxidant concentration (500 mM H2O2), activation rate (63 mM H2O2 h-1), and an acceptable total organic carbon (TOC) limit (~1000 mg/L TOC) to achieve maximum PFAA precursor conversion. Additional work was performed further optimizing the UV-TOP assay, by confirming its superiority to heat activation, identifying the effectiveness of different persulfate salts, and investigating different concentrations of sodium persulfate and sodium hydroxide at a 1:2.5 ratio on PFCA yield. Our investigation concluded by applying the UV-H2O2-TOP assay, using sodium persulfate as the TOP assay oxidant, to 6:2 FTS and five different AFFF samples. High-resolution mass spectrometry and an expanded analytical suite support sample analysis, facilitating direct quantification of ultra-short chain perfluoroalkyl carboxylates (PFCAs) and common fluorotelomer compounds including 5:3/5:1:2 fluorotelomer betaine and 6:2 fluorotelomer sulfonamido betaine. Results highlight several advantages of this tandem UV-activated method, including enhanced preservation of perfluoroalkyl chains (post-oxidation of 6:2 fluorotelomer sulfonate resulted in 28 % PFHpA, 47 % PFHxA, 25 % C3-C5 PFCA), capacity to handle high TOC limits (1000 mg/L TOC), and ability to incorporate higher persulfate concentrations in a single oxidation cycle.

Mechanochemical degradation of per- and polyfluoroalkyl substances in soil using an industrial-scale horizontal ball mill with comparisons of key operational metrics.

Horizontal ball mills (HBMs) have been proven capable of remediating per- and polyfluoroalkyl substances (PFAS) in soil. Industrial-sized HBMs, which could easily be transported to impacted locations for on-site, ex-situ remediation, are readily available. This study examined PFAS degradation using an industrial-scale, 267 L cylinder HBM. This is the typical scale used in the industry before field application. Near-complete destruction of 6:2 fluorotelomer sulfonate (6:2 FTS), as well as the non-target PFAS in a modern fluorotelomer-based aqueous film forming foam (AFFF), was achieved when spiked onto nepheline syenite sand (NSS) and using potassium hydroxide (KOH) as a co-milling reagent. Perfluorooctanesulfonate (PFOS) showed much better and more consistent results with scale-up regardless of KOH. Perfluorooctanoate (PFOA) was examined for the first time using a HBM and behaved similarly to PFOS. Highly challenging field soils from a former firefighting training area (FFTA) were purposefully used to test the limits of the HBM. To quantify the effectiveness, free fluoride analysis was used; changes between unmilled and milled soil were measured up to 7.8 mg/kg, which is the equivalent of 12 mg/kg PFOS. Notably, this does not factor in insoluble fluoride complexes that may form in milled soils, so the actual amount of PFAS destroyed may be higher. Soil health, evaluated through the assessment of key microbial and associated plant health parameters, was not significantly affected as a result of milling, although it was characterized as poor to begin with. Leachability reached 100 % in milled soil with KOH, but already ranged from 81 to 96 % in unmilled soil. A limited assessment of the hazards associated with the inhalation of PFAS-impacted dust from ball-milling, as well as the cross-contamination potential to the environment, showed that the risk was low in both cases; however, precautions should always be taken.

Occurrence and mobility of thiolated arsenic in legacy mine tailings.

We studied the occurrence of dissolved thiolated Arsenic (As) in legacy tailings systems in Ontario and Nova Scotia, Canada, and used aqueous and mineralogical speciation analyses to assess its governing geochemical controls. Surface-accessible and inundated tailings in Cobalt, Ontario, contained ∼1 wt-% As mainly hosted in secondary arsenate minerals (erythrite, yukonite, and others) and traces of primary sulfide minerals (cobaltite, gersdorffite and others). Significant fractions of thiolated As (up to 5.9 % of total dissolved As) were detected in aqueous porewater and surface water samples from these sites, comprising mostly monothioarsenate, and smaller amounts of di- and tri-thioarsenates as well as methylated thioarsenates. Tailings at the Goldenville and Montague sites in Nova Scotia contained less (<0.5 wt-%) As, hosted mostly in arsenopyrite and As-bearing pyrite, than the Cobalt sites, but exhibited higher proportions of dissolved thiolated As (up to 17.3 % of total dissolved As, mostly mono- and di-thioarsenate and traces of tri-thioarsenate). Dissolved thiolated As was most abundant in sub-oxic porewaters and inundated tailings samples across the studied sites, and its concentrations were strongly related to the prevailing redox conditions and porewater hydrochemistry, and to a lesser extent, the As-bearing mineralogy. Our novel results demonstrate that thiolated As species play an important role in the cycling of As in mine waste systems and surrounding environments, and should be considered in mine waste management strategies for high-As sites.

Forever no more: Complete mineralization of per- and polyfluoroalkyl substances (PFAS) using an optimized UV/sulfite/iodide system.

As the global issue of PFAS contamination in water continues to grow there exists a need for technologies capable of fully mineralizing PFAS in water, with destruction being measured as both a loss of the initial PFAS and a quantitative recovery of the resultant fluoride ions. This study investigates the use of sulfite and iodide in a bicarbonate-buffered alkaline system activated with ultraviolet (UV) light to destroy PFAS. The UV/sulfite/iodide system creates a reductive environment through the generation of aqueous electrons, which can degrade PFAS. The extent of degradation and defluorination was explored for perfluorooctane sulfonic acid (PFOS), perfluorooctanoic acid (PFOA), 6:2 fluorotelomer sulfonic acid (6:2 FTS), and perfluorobutane sulfonic acid (PFBS). An initial UV/sulfite/iodide system achieved 100 % degradation and > 90 % defluorination for PFOS, PFOA, and 6:2 FTS, but was not capable of completely degrading PFBS. Transformation product elucidation experiments were performed for PFOS under different UV systems, and 6:2 FtSaB using the initial UV/sulfite/iodide system. Several transformation products were identified including -nF/+nH PFOS (n = 1-13), -F/+H shorter-chain PFSAs, 6:2 fluorotelomer sulfonamidoamine (6:2 FtSaAm), 6:2 fluorotelomer sulfonamide, and 6:2 fluorotelomer unsaturated sulfonamide. Novel identification of -F/+H perfluoropropane sulfonic acid (PFPS) and -F/+H perfluoroethane sulfonic acid (PFES) following degradation of PFOS confirms CC bond cleavage, and different isomers of -F/+H PFOS confirms the potential for CF bond cleavage to occur throughout the perfluoroalkyl chain. Additional optimization experiments were performed aiming to fully degrade PFBS. The optimal protocol found in this study involved an elevated initial sulfite concentration and adding additional sulfite at regular intervals during UV-activation, achieving >99.9 % destruction and complete quantitative defluorination of PFBS.

Elucidating the relationship between PFOA and PFOS destruction, particle size and electron generation in amended media commonly found in soils.

Ball milling has emerged as a promising destructive technique for treating per- and polyfluoroalkyl substances (PFAS)-impacted soils. Environmental media properties such as reactive species generated upon ball milling and particle size are postulated to influence the effectiveness of the technology. In this study, four media types amended with perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) were planetary ball milled to investigate destruction, fluoride recovery without additional co-milling reagents and the relationship between PFOA and PFOS destruction, particle size during milling, and electron generation. Silica sand, nepheline syenite sand, calcite and marble were sieved to achieve similar initial particle sizes (6/35 distribution), amended with PFOA and PFOS, and milled for 4 h. Particle size analysis was conducted throughout milling and 2,2-diphenyl-1-picrylhydrazyl (DPPH•) was used as a radical scavenger to assess electron generation from the four media types. Particle size reduction was observed to be positively correlated to PFOA and PFOS destruction and DPPH• neutralization (demonstrating electron generation by milling) in silica sand and nepheline syenite sand. Milling of a fine fraction (< 500 µm) of silica sand revealed less destruction compared to the 6/35 distribution suggesting the ability to fracture grains in silicate media is integral to PFOA and PFOS destruction. DPPH• neutralization was demonstrated in all four amended media types, confirming silicate sands and calcium carbonates generate electrons as a reactive species during ball milling. Fluoride loss as a function of milling time was observed in all amended media types. A sodium fluoride (NaF) spiked was used to quantify fluoride loss in the media independent of PFAS. A method was developed using the NaF-amended media fluoride concentrations to estimate the total fluorine liberated from PFOA and PFOS by ball milling. Estimates produced suggest complete recovery of theoretical fluorine yield is obtained. Data from this study was used to propose a reductive destruction mechanism for PFOA and PFOS.

Parsimonious methodology for synthesis of silver and copper functionalized cellulose.

Metal nanomaterials, such as silver and copper, are often incorporated into commercial textiles to take advantage of their Antibacterial and antiviral properties. The goal of this study was to identify the most parsimonious method for the synthesis of silver, copper, or silver/copper bimetallic treated textiles. To accomplish this eight different methods were employed to synthesize silver, copper, and silver/copper functionalized cotton batting textiles. Using silver and copper nitrate as precursors, different reagents were used to initiate/catalyze the deposition of metal, including: (1) no additive, (2) sodium bicarbonate, (3) green tea, (4) sodium hydroxide, (5) ammonia, (6, 7) sodium hydroxide/ammonia at a 1:2 and 1:4 ratio, and (8) sodium borohydride. The use of sodium bicarbonate as a reagent to reduce silver onto cotton has not been used previously in literature and was compared to established methods. All synthesis methods were performed at 80 °C for one hour following textile addition to the solutions. The products were characterized by x-ray fluorescence (XRF) analysis for quantitative determination of the metal content and x-ray absorption near edge structure (XANES) analysis for silver and copper speciation on the textile. Scanning electron microscopy (SEM) with energy dispersive x-ray (EDX) and size distribution inductively coupled plasma mass spectrometry (ICP-MS) were used to further characterize the products of the sodium bicarbonate, sodium hydroxide, and sodium borohydride synthesis methods following ashing of the textile. For the silver treatment methods (1 mM Ag +), sodium bicarbonate and sodium hydroxide resulted in the highest amounts of silver on the textile (8900 mg Ag/kg textile and 7600 mg Ag/kg textile) and for copper treatment (1 mM Cu +) the sodium hydroxide and sodium hydroxide/ammonium hydroxide resulted in the highest amounts of copper on the textile (3800 mg Ag/kg textile and 2500 mg Ag/kg textile). Formation of copper oxide was dependent on the pH of the solution, with 4 mM ammonia and other high pH solutions resulting in majority of the copper on the textile existing as copper oxide, with smaller amounts of ionic-bound copper. The identified parsimonious methods will lend themselves to the efficient manufacturing of antibacterial and antiviral textiles, or the development of multifunctionalized smart textiles. Supplementary Information: The online version contains supplementary material available at 10.1007/s10570-023-05099-7.

Peaks, pores, and dragon eggs: Uncovering and quantifying the heterogeneity of treatment wetland biofilm matrices.

Biofilms serve to house diverse microbial communities, which are responsible for the majority of wastewater constituent degradation and transformation in treatment wetlands (TWs). TW biofilm has been generally conceptualized as a relatively uniform film covering available surfaces. However, no studies attaining direct visual 3D representations of biofilm morphology have been conducted. This study focuses on imaging the morphology of detached, gravel-associated, and rhizospheric (Phalaris arundinacea) biofilms from subsurface TW mesocosms. Images obtained through both traditional light microscopy, environmental scanning electron microscopy (E-SEM) and Wet-SEM revealed that TW biofilms are structurally heterogeneous ranging from corrugated films to clusters of aggregates. Features such as water channels and pores were observed suggesting that pollutant transport inside biofilms is complex, and that the interfacial surface area between water and biofilm is much larger than previously understood. Biofilm thickness generally ranged between 170 and 240 µm, with internal biofilm porosities estimated as 34 ± 10 %, reaching a maximum of 50 %. Internal biofilm matrix pore diameters ranged from 1 to 205.2 µm, with a distribution that favored pores and channels smaller than 10 µm, and a mean equivalent spherical diameter of 8.6 µm. Based on the large variation in pore and channel sizes it is expected that a variety of flow regimes and therefore pollutant dynamics are likely to occur inside TW biofilm matrices. Based on the visual evidence and analysis, a new conceptual model was created to reflect the microscale TW biofilm dynamics and morphology. This new conceptual model will serve to inform future biokinetic modelling, microscale hydrology, microbial community assessment, and pollutant treatment studies.

Retention of PFOS and PFOA Mixtures by Trapped Gas Bubbles in Porous Media.

The transport of per- and polyfluoroalkyl substances (PFAS) in soil and groundwater is important for site investigation, risk characterization, and remediation planning. The adsorption of PFAS at air-water interfaces has been shown to significantly contribute to PFAS retention, with subsequent effects on concentrations and the time scales of transport. In this study, column experiments were conducted to investigate the transport of perfluorooctanesulfonic acid (PFOS), perfluorooctanoic acid (PFOA), and 6:2 fluorotelomer sulfonate (6:2 FTS) individually and in binary mixtures in the presence of a trapped gas phase, using clean sands to isolate adsorption to air-water interfaces. Consistent with previous studies, the transport of PFOS, PFOA, and 6:2 FTS was retarded by adsorption at the air-water interface, with greater retention of PFOS due to its higher affinity for the air-water interface. Chromatographic separation occurred in the experiments using binary mixtures of PFOS and PFOA, with greater retention at lower influent concentrations. The mixture experiments also showed enhanced breakthrough of PFOA in the presence of PFOS, where effluent concentrations of PFOA were temporarily greater than the influent concentration prior to the breakthrough of PFOS. This enhanced breakthrough was attributed to competition between PFOS and PFOA for adsorption to the air-water interface.

Use of a horizontal ball mill to remediate per- and polyfluoroalkyl substances in soil.

There is a need for destructive technologies for per- and polyfluoroalkyl substances (PFAS) in soil. While planetary ball mill have been shown successful degradation of PFAS, there are issues surrounding scale up (maximum size is typically 0.5 L cylinders). While having lower energy outputs, horizontal ball mills, for which scale up is not a limiting factor, already exist at commercial/industrial sizes from the mining, metallurgic and agricultural industries, which could be re-purposed. This study evaluated the effectiveness of horizontal ball mills in degrading perfluorooctanesulfonate (PFOS), 6:2 fluorotelomer sulfonate (6:2 FTSA), and aqueous film forming foam (AFFF) spiked on nepheline syenite sand. Horizontal ball milling was also applied to two different soil types (sand dominant and clay dominant) collected from a firefighting training area (FFTA). Liquid chromatography tandem mass spectrometry was used to track 21 target PFAS throughout the milling process. High-resolution accurate mass spectrometry was also used to identify the presence and degradation of 19 non-target fluorotelomer substances, including 6:2 fluorotelomer sulfonamido betaine (FtSaB), 7:3 fluorotelomer betaine (FtB), and 6:2 fluorotelomer thioether amido sulfonate (FtTAoS). In the presence of potassium hydroxide (KOH), used as a co-milling reagent, PFOS, 6:2 FTSA, and the non-target fluorotelomer substances in the AFFF were found to undergo upwards of 81%, 97%, and 100% degradation, respectively. Despite the inherent added complexity associated with field soils, better PFAS degradation was observed on the FFTA soils over the spiked NSS, and more specifically, on the FFTA clay over the FFTA sand. These results held through scale-up, going from the 1 L to the 25 L cylinders. The results of this study support further scale-up in preparation for on-site pilot tests.

Elucidating degradation mechanisms for a range of per- and polyfluoroalkyl substances (PFAS) via controlled irradiation studies.

Per- and polyfluoroalkyl substances (PFAS) are a challenging class of environmental pollutants due to a lack of available destructive remediation technologies. Understanding the fundamental mechanisms for degradation of PFAS is key for the development of field scalable and in-situ destructive based remediation technologies. This study aimed to elucidate and refine the current understanding of PFAS degradation mechanisms in water through a series of controlled gamma irradiation studies. Gamma irradiation of PFAS was performed using a cobalt-60 source in a batch irradiation up to 80 kGy at the Australian Nuclear Science and Technology Organisation. Perfluorooctanoic acid (PFOA), perfluorooctanesulfonic acid (PFOS), 6:2 fluorotelomer sulfonate (6:2 FTS), and a suite of thirteen different PFAS (including C4-C12 PFCAs, C4, C6, C8 PFSAs, and FOSA) were irradiated to investigate degradation, influence of pH, chain length, and transformation. High resolution mass spectrometry was used to identify more than 80 fluorinated transformation products throughout the degradation experiments. These included the -F/+H, -F/+OH, -F/CH2OH exchanged PFAS and n - 1 PFCA, amongst others. Given the reactive species present (hydroxyl radicals (·OH), hydrogen radicals (·H) and aqueous electrons (e-aq)), and the degradation products formed it was shown that aqueous electrons were the key reactive species responsible for initial PFAS degradation. Most importantly, based on degradation product formation, we found that the initial -F/+H does not have to occur at the α-fluoride (nearest the functional head group), rather occurring throughout the chain length leading to more complex degradation pathways than previously postulated. While our results support some of the reaction steps postulated in the literature, we have developed a unified 16 step and 3 pathway schematic of degradation supported by experimental observations.

Silver nanomaterials released from commercial textiles have minimal impacts on soil microbial communities at environmentally relevant concentrations.

Silver nanomaterials (Ag NMs) have been used in a variety of commercial products to take advantage of their antimicrobial properties. However, there are concerns that these AgNMs can be released during/after use and enter wastewater streams, potentially impacting aquatic systems or accumulating in wastewater biosolids. Biosolids, which are a residual of wastewater treatment processes, have been found to contain AgNMs and are frequently used as agricultural fertilizer. Since the function of soil microbial communities is imperative to nutrient cycling and agricultural productivity, it is important to characterize and assess the effects that silver nanomaterials could have in agricultural soils. In this study agricultural soil was amended with pristine engineered (PVP-coated or uncoated AgNMs), aged silver (sulphidized or released from textiles) nanomaterials, and ionic silver to determine the fate and toxicity over the course of three months. Exposures were carried out at various environmentally relevant concentrations (1 and 10 mg Ag/kg soil) representing between 30 to over 800 years of equivalent biosolid loadings. Over thirteen different methodologies and measures were used throughout this study to assess for potential effects of the silver nanomaterials on soil, including microbial community composition, average well colour development (AWCD) and enzymatic activity. Overall, the AgNM exposures did not exhibit significant toxic effects to the soil microbial communities in terms of density, activity, function and diversity. However, the positive ionic silver treatment (100 mg Ag/kg soil) resulted in suppression to microbial activity while also resulting in significantly higher populations of Frankia alni (nitrogen-fixer) and Arenimonas malthae (phytopathogen) as compared to the negative control (p < 0.05, Tukey HSD) which warrants further investigation.

Electrokinetically-enhanced emplacement of lactate in a chlorinated solvent contaminated clay site to promote bioremediation.

Bioremediation through the injection of electron donors and bacterial cultures is effective at treating chlorinated solvent contamination. However, it has had limited application in low permeability zones where amendments cannot be delivered successfully. This field-scale study investigated the application of electrokinetics to enhance the delivery of lactate at a clay site contaminated with chlorinated solvents. Groundwater and soil samples were collected before, during and for 1 year after the 71-day field test and analyzed for a wide suite of chemical and biological parameters. Lactate was successfully delivered to all monitoring locations. Lactate emplacement resulted in the stimulation of bacterial populations, specifically within the phylum Firmicutes, which contains fermenters and strict anaerobes. This likely led to biodegradation, as the field trial resulted in significant decreases in both soil and aqueous phase chlorinated solvent concentrations. Contaminant decreases were also partially attributable to dilution, given evidence of some advective lactate flux. This research provides evidence that electrokinetically-enhanced bioremediation has potential as a treatment strategy for contaminated low permeability strata.

Development and validation of a method for the weathering and detachment of representative nanomaterials from conventional silver-containing textiles.

Nanotoxicology research commonly utilizes pristine nanomaterials for toxicity assessment, which may not be perfectly representative of what is released into environmental systems. The goal of the present study was to develop a method to simulate human weathering of silver-containing textiles. To achieve this goal the roles of physical and chemical stress on X-Static® containing athletic textiles were investigated and compared to data collected from human weathering experiments and literature. Chemical weathering methods (artificial sweat) were used independently and alongside physical weathering methods (3D printed stretching and abrasion instruments). Non-weathered control textiles were found to release 29 ± 11 mg Ag/kg of textile into wash water effluent (ICP-MS), with 16% being released as ionic silver (ICP-MS) and the rest as metallic nanomaterials, nanosheets, and particulates of varying size (SEM/XANES). Real and simulated human weathered textiles released similar amounts of total silver (67 ± 11 mg Ag/kg, 84 ± 13 mg Ag/kg respectively) with the silver released being composed of ionic (1.5%, 2%) and a mixture of metallic and chlorinated nanomaterials, nanosheets, and particulates. The method was shown to effectively detach environmentally representative silver materials from silver-containing textiles and can provide such materials for future studies on the assessment of their fate, transport, and toxicity.

Mechanochemical remediation of perfluorooctanesulfonic acid (PFOS) and perfluorooctanoic acid (PFOA) amended sand and aqueous film-forming foam (AFFF) impacted soil by planetary ball milling.

Per- and polyfluoroalkyl substances (PFAS) are manmade, fluorinated organic chemicals which have been identified as persistent organic pollutants. PFAS have surface active properties that have made them suitable for applications in oil- and water-resistant products, as well as many firefighting foams. No on-site remediation strategies exist to treat PFAS impacted soils. Mechanochemical remediation of PFOS- and PFOA-amended sand via a planetary ball mill was studied. The effect of sand mass, KOH as a co-milling reagent, and water saturation on the degradation of PFOA and PFOS was evaluated. By 4 h of milling concentrations were reduced by up to 98% for PFOS-amended dry sand and 99% for PFOA-amended dry sand without the addition of a co-milling reagent. Water saturation was determined to be a significant hindrance on the mechanochemical destruction of PFOS and PFOA. A maximum of 89% of fluoride was recovered from PFOS-amended sand when KOH was used as a co-milling reagent. It is hypothesized that reactive particles generated from the fracture of sand grains react with PFAS molecules to initiate destruction, which can result in full defluorination. Milling experiments were also conducted on soils from a Canadian firefighting training area (FFTA), demonstrating that PFOS concentrations can be reduced by up to 96% in site soils. For the first time, ball milling for the remediation of PFAS in environmental media has been demonstrated using amended sand and legacy soils from a FFTA.

A group-contribution model for predicting the physicochemical behavior of PFAS components for understanding environmental fate.

The factors controlling per- and polyfluoroalkyl substances (PFAS) environmental fate remains the subject of considerable debate and study. As surfactants, PFAS readily partition to interfaces, a property that controls their transport and fate. A group contribution model is developed to predict the extent to which PFAS partitions to the air-water interface. Langmuir adsorption and Szyszkowski equation parameters were fitted to literature air-water surface tension data for a range of PFAS and conventional hydrocarbon surfactants. This approach enabled the prediction of the impact of the hydrophilic head group, and other molecular components, on PFAS interfacial partitioning in instances when PFAS data are unavailable but analogous hydrocarbon surfactant data are available. The model was extended to predict a range of parameters (i.e., solubility, critical micelle concentration (CMC), KD, Koc and Kow) that are used to predict PFAS environmental fate, including long-range PFAS transport and in multimedia models. Model predictions were consistent with laboratory and field derived parameters reported in the literature. Additionally, the proposed model can predict the impact of pH and speciation on the extent of PFAS interfacial partitioning, a potentially important feature for understanding the behaviors of some ionizable PFAS, such as fluorinated carboxylic acids. The proposed model provides a conceptually straightforward method to predict a wide range of environmental fate parameters for a wide range of PFAS. As such, the model is a powerful tool that can be used to determine parameters needed to predict PFAS environmental fate.

Remediation of PFAS-Contaminated Soil and Granular Activated Carbon by Smoldering Combustion.

This study explored smoldering combustion for remediating polyfluoroalkyl substance (PFAS)-impacted granular activated carbon (GAC) and PFAS-contaminated soil. GAC, both fresh and PFAS-loaded, was employed as the supplemental fuel supporting smoldering in mixtures with sand (≈175 mg PFAS/kg GAC-sand), with PFAS-spiked, laboratory-constructed soil (≈4 mg PFAS/kg soil), and with a PFAS-impacted field soil (≈0.2 mg PFAS/kg soil). The fate of PFAS and fluorine was quantified with soil and emission analyses, including targeted PFAS and suspect screening as well as hydrogen fluoride and total fluorine. Results demonstrated that exceeding 35 g GAC/kg soil resulted in self-sustained smoldering with temperatures exceeding 900 °C. Post-treatment PFAS concentrations of the treated soil were near (2 experiments) or below (7 experiments) detection limits (0.0004 mg/kg). Further, 44% of the initial PFAS on GAC underwent full destruction, compared to 16% of the PFAS on soil. Less than 1% of the initial PFAS contamination on GAC or soil was emitted as PFAS in the quantifiable analytical suite. Results suggest that the rest were emitted as altered, shorter-chain PFAS and volatile fluorinated compounds, which were scrubbed effectively with GAC. Total organic fluorine analysis proved useful for PFAS-loaded GAC in sand; however, analyzing soils suffered from interference from non-PFAS. Overall, this study demonstrated that smoldering has significant potential as an effective remediation technique for PFAS-impacted soils and PFAS-laden GAC.

Assessing the role of microbial communities in the performance of constructed wetlands used to treat combined sewer overflows.

Combined sewer overflows are contaminated with various micropollutants which pose risk to both environmental and human health. Some micropollutants, such as carbamazepine and sulfamethoxazole, are very persistent and difficult to remove from wastewater. Event loaded vertical-flow constructed wetlands (retention soil filters; RSFs) have proven to be effective in the treatment of combined sewer overflows for a wide range of pollutants. However, little is known about how microbial communities contribute to the treatment efficiency, specifically to the reduction of micropollutants. To the best of our knowledge, this is the first study attempting to close this gap. Microbial communities in pilot-scale RSFs were investigated, which showed explicit grouping of metabolic activity at different filter depths with some differential abundance of identified genera. The highest microbial activity was found in the top layer of 0.75 m deep filters, whereas homogeneous activity dominated in a 0.50 m deep filter, indicating oxygen availability to be a limiting factor of the metabolic activity in RSFs. The removal efficiencies of all investigated organic trace substances were correlated to the utilization of specific carbon sources. Most notable is the correlation between the carbon source glucose-1-phosphate and the removal of metoprolol. The strongest correlations for other substances were the removal of diclofenac to the utilization of the carbohydrate i-erythritole; bisphenol A to carbohydrate α-d-lactose, and 1-H-benzotriazole to carbonic acid D-galacturonic acid. Those results are supported by positive correlations of specific microbial genera with both the utilization of the above mentioned carbon sources and the removal efficiency for the respective micropollutants. Most notable is correlation of Tetrasphaera and the removal of benzotriazole and diclofenac.

Influence of Plant Species on Microbial Activity and Denitrifier Population Development in Vegetated Denitrifying Wood-Chip Bioreactors.

The microbial characteristics of four vegetated and one unplanted wood-chip bioreactors treating greenhouse effluent were investigated in a continuous experiment operated for over 2.5 years. The bioreactors were designed to reduce nitrate concentrations via naturally induced microbial denitrification. The vegetation type and reactor depth were both found to be significant factors in defining the mixed microbial activity. However, a consistent correlation between the abundance of the denitrifying communities and reactor depth could not be found across all reactors. The media samples from the unit planted with Typha angustifolia displayed higher microbial activities compared with the other reactors. This plant's root-associated bacteria also demonstrated the greatest copies of the denitrifying genes nirK and nosZ. The most abundant denitrifier communities and those encoding the nosZ gene were found in the unplanted reactor, followed by the T. angustifolia unit. The T. angustifolia reactor demonstrated greater microbial activity and denitrification capacity at the depth of 20 cm, while the greatest denitrification capacity in the unplanted reactor was found at the depth of 60 cm. These findings indicated the importance of the T. angustifolia rhizosphere to support microbial community establishment and growth in the vicinity of the plant's roots, although those populations may eventually develop in an unplanted environment.

Developing a roadmap to determine per- and polyfluoroalkyl substances-microbial population interactions.

We collected over 40 groundwater samples from a per- and polyfluoroalkyl substances (PFAS) impacted legacy fire fighting training area in Canada to develop an in-depth assessment of the relationship between PFAS and in situ microbial communities. Results suggest differential transport of PFAS of differing chain-length and head group. There is also evidence of PFAS degradation, in particular 6:2 FTS degradation. Although PFAS constituents were not major drivers of microbial community structure, the relative abundance of over one hundred individual genera were significantly associated with PFAS chemistry. For example, lineages within the Oxalobacteraceae family had strong negative correlations with PFAS, whilst the Desulfococcus genus has strong positive correlations. Results also suggest a range of genera may have been stimulated at low to mid-range concentrations (e.g., Gordonia and Acidimicrobium), with some genera potentially inhibited at high PFAS concentrations. Any correlations identified need to be further investigated to determine the underlying reasons for observed associations as this is an open field site with the potential for many confounding factors. Positive correlations may ultimately provide important insights related to development of biodegradation technologies for PFAS impacted sites, while negative correlations further improve our understanding of the potential negative effects of PFAS on ecosystem health.