RESUMO
Physicochemical properties important in exposure characterisation of four different welding aerosols were investigated. Particle number size distributions were determined by scanning mobility particle sizer (SMPS), mass size distributions by separation and weighing the individual size fractions of an 11-stage cascade impactor. The size distribution of the primary particles of agglomerates, chemical composition and morphology of the particles were examined by TEM. There were significant differences in the particle number size distributions of the different welding aerosols according to the SMPS determinations. The particle mass size distributions determined gravimetrically were, however, not really different. The dominant range with respect to mass was between 0.1 and 1 µm, regardless of the welding technique. Most of the primary particles in all different welding aerosols had diameters between 5 and 40 nm. All types of primary particles had a tendency to form chainlike agglomerates. A clear size dependence of the particle chemical composition was encountered in the case of manual metal arc welding aerosol. Small particles with diameters below 50 nm were mostly metal oxides in contrast to larger particles which also contained more volatile elements (e.g. potassium, fluorine, sodium, sulphur).
Assuntos
Aerossóis/análise , Aerossóis/química , Metais/química , Microscopia Eletrônica de Transmissão , Tamanho da Partícula , Propriedades de Superfície , VolatilizaçãoRESUMO
The hygroscopic behaviour of individual aerosol particles from workplaces in a primary aluminium smelter was investigated by environmental scanning electron microscopy. At a high relative humidity, comparable with the human respiratory tract, most particles encountered in the Søderberg and Prebake potrooms either undergo partial deliquescence (leading to a water droplet with an insoluble core) or form thin water films at the surface. As gaseous HF and SO(2) are highly soluble in water, the aerosol particles may act as carrier for these two gases into the alveolar region of the lower respiratory tract. Based on a one-dimensional mass balance model, it is estimated that under peak exposure conditions (particle surface area concentration of 10(-4) cm(2) cm(-3)) approximately 10% of the initial gaseous HF may be transferred to the particle phase. For SO(2), this fraction is much lower (approximately 1%). These results indicate that at least HF may penetrate deeper into the lung in the presence of soluble particles or particles that form surface water films compared to HF alone.
Assuntos
Poluentes Ocupacionais do Ar/química , Alumínio/química , Ácido Fluorídrico/farmacocinética , Dióxido de Enxofre/farmacocinética , Aerossóis , Humanos , Ácido Fluorídrico/química , Exposição por Inalação , Pulmão/metabolismo , Microscopia Eletrônica , Microscopia Eletrônica de Varredura , Dióxido de Enxofre/química , Propriedades de Superfície , Difração de Raios XRESUMO
The oxidation state of sulfur has been determined by measuring the energy shift of the S K(alpha) line by wavelength-dispersive electron-probe microanalysis. On flat polished samples the energy shift between sulfate (S(+6)) and sulfide (S(-2)) was 1.3 eV, in good agreement with previous literature data. The observed energy shift of the S K(alpha) line is dominated by the change of the valence state of sulfur--the effects of co-ordination geometry and nearest neighbours are small. The relationship between the energy shift of the S K(alpha) line and the oxidation number of sulfur is linear, to a first approximation. The effect of particle geometry on the position of the S K(alpha) line is usually small and introduces an error of approximately half an oxidation number. The apparent sulfur valence states observed for individual aerosol particles from work places in a nickel refinery are highly variable and most probably result from different mixtures of the two end-members sulfide and sulfate.
RESUMO
Aerosol particle samples were collected at ELKEM ASA ferromanganese (FeMn) and silicomanganese (SiMn) smelters at Porsgrunn, Norway, during different production steps: raw material mixing, welding of protective steel casings, tapping of FeMn and slag, crane operation moving the ladles with molten metal, operation of the Metal Oxygen Refinement (MOR) reactor and casting of SiMn. Aerosol fractions were assessed for the analysis of the bulk elemental composition as well as for individual particle analysis. The bulk elemental composition was determined by inductively coupled plasma atomic emission spectrometry. For individual particle analysis, an electron microprobe was used in combination with wavelength-dispersive techniques. Most particles show a complex composition and cannot be attributed to a single phase. Therefore, the particles were divided into six groups according to their chemical composition: Group I, particles containing mainly metallic Fe and/or Mn; Group II, slag particles containing mainly Fe and/or Mn oxides; Group III, slag particles consisting predominantly of oxidized flux components such as Si, Al, Mg, Ca, Na and K; Group IV, particles consisting mainly of carbon; Group V, mixtures of particles from Groups II, III and IV; Group VI, mixtures of particles from Groups II and III. In raw material mixing, particles originating from the Mn ores were mostly found. In the welding of steel casings, most particles were assigned to Group II, Mn and Fe oxides. During the tapping of slag and metal, mostly slag particles from Group III were found (oxides of the flux components). During movement of the ladles, most particles came from Group II. At the MOR reactor, most of the particles belonged to the slag phase consisting of the flux components (Group III). The particles collected during the casting of SiMn were mainly attributed to the slag phase (Groups III and V). Due to the compositional complexity of the particles, toxicological investigations on the kinetics of pure compounds may not be easily associated with the results of this study.
Assuntos
Aerossóis/química , Poluição do Ar em Ambientes Fechados/análise , Manganês/química , Exposição Ocupacional , Ligas , Monitoramento Ambiental , Humanos , Manufaturas , Metalurgia , Metais/análise , Local de TrabalhoRESUMO
Individual aerosol particles (n = 1170) collected at work stations in a nickel refinery were analyzed by wavelength-dispersive electron-probe microanalysis. By placing arbitrary restrictions on the contents of sulfur and silicon, the particles could be divided into four main groups. Scanning electron images indicated that most of the particles examined were relatively small (< or = 2 microm, equivalent projected area diameter), and that their morphology suggested formation from a melt. There was an absence of well-defined phases and simple stoichiometries, indicating that exposures to pure substances such as nickel subsulfide or specific oxides appeared not to occur. Although the elemental composition of particles varied greatly, a rough association was evident with the known elemental content of the refinery intermediates. The implications of the findings for aerosol speciation measurements, toxicological studies and interpretation of adverse health effects are explored.