Probing the hydrolytic degradation of UF4 in humid air.

This manuscript describes the chemical transformations that occur during hydrolysis of uranium tetrafluoride (UF4) due to its storage in humid air (85% and 50% relative humidity) at ambient temperatures. This hydrolysis was previously reported to proceed slowly or not at all (depending on the percent relative humidity); however, previous reports relied primarily on X-ray diffraction methods to probe uranium speciation. In our report, we employ a battery of physiochemical probing techniques to explore potential hydrolysis, including Raman spectroscopy, powder X-ray diffraction, 19F nuclear magnetic resonance spectroscopy, scanning electron microscopy, and focused ion beam microscopy with energy-dispersive X-ray spectroscopy. Of these, only Raman spectroscopy proved to be particularly useful at observing chemical changes to UF4. It was found that anhydrous UF4 slightly oxidizes over the course of thirteen days to Schoepite-like uranium complexes and possibly UO3. In contrast, UF4 exposed to 50% relative humidity slightly decomposes into UO2F2, Schoepite-like uranium complexes, and possibly a high order uranium oxide that eluded chemical assignment (UxOy). Despite the rich chemical speciation observed in our Raman spectroscopy measurements, X-ray diffraction and 19F NMR measurements on the same material showed no changes. Microscopy measurements suggest that the observed reactions between UF4 and water occur primarily on the surface of UF4 particulates via a method that is visually similar to surface corrosion of metals. Therefore, we postulate that NMR spectroscopy and X-ray diffraction, which are well-suited for bulk analysis, are less suited than Raman spectroscopy to observe the surface-based reactions that occur to UF4 when exposed to humid air. Considering the importance of UF4 in the production of nuclear fuel and weapons, the results presented herein are widely applicable to numerous nuclear science fields where uranium detection and speciation in humid environments is of value, including nuclear nonproliferation and nuclear forensics.

Characterizing the solid hydrolysis product, UF4(H2O)2.5, generated from neat water reactions with UF4 at room temperature.

Uranium tetrafluoride (UF4) is an important intermediate in the production of UF6 and uranium metal. Room temperature hydrolysis of UF4 was investigated using a combination of Fluorine-19 nuclear magnetic resonance spectroscopy (19F NMR), Raman and infrared spectroscopy, powder X-ray diffraction, and microscopy measurements. UF4(H2O)2.5 was identified as the primary solid hydrolysis product when anhydrous UF4 was stirred in deionized water. Static NMR and 19F magic angle spinning NMR measurements revealed that a small amount of uranyl fluoride can also form when anhydrous UF4 is left in water, although this species comprises less than 5% of the total sample with the remaining parts being UF4(H2O)2.5. Since UF4 is generally considered to be stable under ambient conditions, these findings mark the first time that a room temperature reaction between UF4 and water has been detected and analyzed without interference from additional chemical reagents. The Raman characterization of UF4(H2O)2.5 presented herein is the first on record. Since UF4 is one of the most used intermediates during chemical conversion of uranium ore to uranium metal for nuclear fuel and weapons, the results presented herein are applicable to numerous nuclear science fields where solid state detection of uranium is of value, including nuclear nonproliferation, nuclear forensics, and environmental remediation.

Matrix-Assisted Ionization of Molecular Uranium Species.

Matrix-assisted ionization (MAI) demonstrates high sensitivity for a variety of organic compounds; however, few studies have reported the application of MAI for the detection and characterization of inorganic analytes. Trace-level uranium analysis is important in the realms of nuclear forensics, nuclear safeguards, and environmental monitoring. Traditional mass spectrometry methods employed in these fields require combinations of extensive laboratory chemistry sample preparation and destructive ionization methods. There has been recent interest in exploring ambient mass spectrometry methods that enable timely sample analysis and higher sensitivity than what is attainable by field-portable radiation detectors. Rapid characterization of uranium at nanogram levels is demonstrated in this study using MAI techniques. Mass spectra were collected on an atmospheric pressure mass spectrometer for solutions of uranyl nitrate, uranyl chloride, uranyl acetate, and uranyl oxalate utilizing 3-nibrobenzonitrile as the ionization matrix. The uranyl complexes investigated were detectable, and the chemical speciation was preserved. Sample analysis was accomplished in a matter of seconds, and limits of detection of 5 ng of uranyl nitrate, 10 ng of uranyl oxalate, 100 ng of uranyl chloride, and 200 ng of uranyl acetate were achieved. The observed gas-phase speciation was similar to negative-ion electrospray ionization of uranyl compounds with notable differences. Six matrix-derived ions were detected in all negative-ion mass spectra, and some of these ions formed adducts with the uranyl analyte. Subsequent analysis of the matrix suggests that these molecules are not matrix contaminants and are instead created during the ionization process.

Rapid paper spray mass spectrometry characterization of uranium and exemplar molecular species.

RATIONALE: The ability to detect and quantify the presence of specific inorganic elements and complexes is essential for environmental monitoring and nuclear safeguards applications. In this work, paper spray ionization mass spectrometry was used for the rapid chemical and isotopic characterization of trace inorganic species collected on cotton swipe substrates. The direct analysis of cotton swipes using this ambient ionization technique led to fast sample analysis that retained original chemical information of the source material with minimal sample preparation. METHODS: Mass spectra were collected with an atmospheric pressure ionization, high-resolution mass spectrometer for solutions containing uranyl acetate, uranyl chloride, uranyl nitrate, and uranyl tri-n-butylphosphate complexes. Gadolinium nitrate was used as an internal standard for the quantitative analysis of uranium. To demonstrate the ability to characterize inorganic contaminants in the presence of uranium, a multi-element inorganic standard containing U, Bi, Pb, Cd, Fe, and Zn was deposited onto cotton substrates and directly analyzed without purification. RESULTS: All elements doped on the cotton substrate were detected with strong signal-to-noise ratios (ca 1000 for UO2 + on multi-element doped swipes) and high integrated intensities (>105 counts) from collection periods of approximately 1 min. Limits of detection were determined to be approximately 94 ng for UO2 + and uranyl acetate through the measurement of ppb level solutions. CONCLUSIONS: The rapid analysis of uranium and other inorganic-containing samples while still retaining original chemical information (e.g. uranyl complexation) was demonstrated. Qualitative detection and speciation were achieved in less than 1 min of analysis. For uranium isotopic quantitation, longer accumulations (>15 min) can be sustained to improve the accuracy of minor 235 U isotopic abundance measurements to approximately 1% error.

Investigations of Uranyl Fluoride Sesquihydrate (UO2F2·1.57H2O): Combining 19F Solid-State MAS NMR Spectroscopy and GIPAW Chemical Shift Calculations.

High-resolution 19F magic-angle spinning (MAS) NMR spectra were obtained for the uranium-bearing solid uranyl fluoride sesquihydrate (UO2F2·1.57H2O). While there are seven distinct crystallographic fluorine sites, the 19F NMR spectrum reveals six peaks at -33.3, 9.1, 25.7, 33.0, 39.0, and 48.2 ppm, with the peak at 33.0 ppm twice the intensity of all the others and therefore corresponding to two sites. To assign the peaks in the experimental spectra to crystallographic sites, 19F chemical shifts were calculated using the gauge including projector augmented waves (GIPAW) plane-wave pseudopotential approach for a DFT-optimized crystal structure. The peak assignments from DFT are consistent with two-dimensional double-quantum 19F MAS NMR experiments.

Rhenium filament oxidation: Effect on TIMS performance and the roles of carburization and humidity.

This communication presents findings on the effect of rhenium filament oxidation on thermal ionization mass spectrometry (TIMS) analyses of plutonium. Additionally, the roles of atmospheric humidity and carburization on the oxidation characteristics (i.e. aging) of rhenium filaments were studied. Degassed and carburized filaments were aged for up to 79 days under dry and humid conditions, and the growth of oxo-rhenium crystallites was investigated intermittently by scanning electron microscopy (SEM) to construct growth profiles. SEM images were analyzed to determine average crystallite size, number density, and percent surface coverage. Crystallite growth was found to be suppressed by both filament carburization and dry storage conditions (~13% relative humidity). Under humid conditions (75% relative humidity), crystallite growth progressed steadily over the investigatory period, reaching >2.3% surface coverage within 79 days of aging. Atomic ion production of Pu (Pu+) was suppressed by approximately 20% and the standard deviation of isotope ratio measurements was increased by 170% when filaments with 1% oxide surface coverage were used in sample loading. Measurement sensitivity and reproducibility are imperative for applications involving ultra-trace analysis of plutonium by TIMS. These findings offer validation for observations regarding the detrimental effect of excessive filament aging post-degassing, improve the understanding of conditions that impel the oxidation of rhenium filaments, and provide practical means to suppress the growth of oxides.

Ambient aging of rhenium filaments used in thermal ionization mass spectrometry: Growth of oxo-rhenium crystallites and anti-aging strategies.

Degassing is a common preparation technique for rhenium filaments used for thermal ionization mass spectrometric analysis of actinides, including plutonium. Although optimization studies regarding degassing conditions have been reported, little work has been done to characterize filament aging after degassing. In this study, the effects of filament aging after degassing were explored to determine a "shelf-life" for degassed rhenium filaments, and methods to limit filament aging were investigated. Zone-refined rhenium filaments were degassed by resistance heating under high vacuum before exposure to ambient atmosphere for up to 2 months. After degassing the nucleation and preferential growth of oxo-rhenium crystallites on the surface of polycrystalline rhenium filaments was observed by atomic force microscopy and scanning electron microscopy (SEM). Compositional analysis of the crystallites was conducted using SEM-Raman spectroscopy and SEM energy dispersive X-ray spectroscopy, and grain orientation at the metal surface was investigated by electron back-scatter diffraction mapping. Spectra collected by SEM-Raman suggest crystallites are composed primarily of perrhenic acid. The relative extent of growth and crystallite morphology were found to be grain dependent and affected by the dissolution of carbon into filaments during annealing (often referred to as carbonization or carburization). Crystallites were observed to nucleate in region specific modes and grow over time through transfer of material from the surface. Factors most likely to affect the rates of crystallite growth include rhenium substrate properties such as grain size, orientation, levels of dissolved carbon, and relative abundance of defect sites; as well as environmental factors such as length of exposure to oxygen and relative humidity. Thin (∼180 nm) hydrophobic films of poly(vinylbenzyl chloride) were found to slow the growth of oxo-rhenium crystallites on the filament surfaces and may serve as an alternative carbon source for filament carburization.

Synthesis and characterization of a lithium-doped fullerane (Li(x)-C60-H(y)) for reversible hydrogen storage.

Herein, we present a lithium-doped fullerane (Li(x)-C(60)-H(y)) that is capable of reversibly storing hydrogen through chemisorption at elevated temperatures and pressures. This system is unique in that hydrogen is closely associated with lithium and carbon upon rehydrogenation of the material and that the weight percent of H(2) stored in the material is intimately linked to the stoichiometric ratio of Li:C(60) in the material. Characterization of the material (IR, Raman, UV-vis, XRD, LDI-TOF-MS, and NMR) indicates that a lithium-doped fullerane is formed upon rehydrogenation in which the active hydrogen storage material is similar to a hydrogenated fullerene. Under optimized conditions, a lithium-doped fullerane with a Li:C(60) mole ratio of 6:1 can reversibly desorb up to 5 wt % H(2) with an onset temperature of ~270 °C, which is significantly less than the desorption temperature of hydrogenated fullerenes (C(60)H(x)) and pure lithium hydride (decomposition temperature 500-600 and 670 °C respectively). However, our Li(x)-C(60)-H(y) system does not suffer from the same drawbacks as typical hydrogenated fullerenes (high desorption T and release of hydrocarbons) because the fullerene cage remains mostly intact and is only slightly modified during multiple hydrogen desorption/absorption cycles. We also observed a reversible phase transition of C(60) in the material from face-centered cubic to body-centered cubic at high levels of hydrogenation.

Multifunctional FePt nanoparticles for radiation-guided targeting and imaging of cancer.

A multifunctional FePt nanoparticle was developed that targets tumor microvasculature via "radiation-guided" peptides, and is detected by both near-infrared (NIR) fluorescence imaging and analytical mass spectrometry methods. Tumor specific binding was first measured by biotinylated peptide linked to fluorophore-conjugated streptavidin. This showed tumor selective binding to tumors using the HVGGSSV peptide. FePt nanoparticles were synthesized sequentially by surface modification with poly(L)lysine, poly(ethylene) glycol conjugation, and functionalized with HVGGSSV peptide and fluorescent probe Alexa fluor 750. NIR fluorescence imaging and ICP-MS analysis showed significant HVGGSSV-FePt nanoparticle binding to irradiated tumors as compared to unirradiated tumors and controls. Results indicate that multifunctional FePt nanoparticles have potential application for radiation-guided targeting and imaging of cancer.

Confined-plume chemical deposition: rapid synthesis of crystalline coatings of known hard or superhard materials on inorganic or organic supports by resonant IR decomposition of molecular precursors.

A one-step process for preparing microcrystalline coatings of known superhard, very hard, or ultraincompressible ceramic compositions on either inorganic or organic supports is reported. Midinfrared pulsed-laser irradiation of preceramic chemical precursors layered between IR-transmissive hard/soft supports under temporal and spatial confinement at a laser wavelength resonant with a precursor vibrational band gives one-step deposition of crystalline ceramic coatings without incurring noticeable collateral thermal damage to the support material. Reaction plume formation at the precursor/laser beam interface initiates confined-plume, chemical deposition (CPCD) of crystalline ceramic product. Continuous ceramic coatings are produced by rastering the laser beam over a sample specimen. CPCD processing of the Re-B single-source precursor, (B(3)H(8))Re(CO)(4), the dual-source mixtures, Ru(3)(CO)(12)/B(10)H(14) or W(CO)(6)/B(10)H(14), and the boron/carbon single-source precursor, o-B(10)C(2)H(12), confined between Si wafer or NaCl plates gives microcrystalline deposits of ReB(2), RuB(2), WB(4), or B(4)C, respectively. CPCD processing of Kevlar fabric wetted by (B(3)H(8))Re(CO)(4) produces an oriented, microcrystalline coating of ReB(2) on the Kevlar fabric without incurring noticeable thermal damage of the polymer support. Similarly, microcrystalline coatings of ReB(2) can be formed on IR-transmissive IR2, Teflon, or Ultralene polymer films.

Novel catalytic effects of fullerene for LiBH4 hydrogen uptake and release.

The addition of catalysts to complex hydrides is aimed at enhancing the hydrogen absorption desorption properties. Here we show that the addition of carbon nanostructure C60 to LiBH4 has a remarkable catalytic effect, enhancing the uptake and release of hydrogen. A fullerene-LiBH4 composite demonstrates catalytic properties with not only lowered hydrogen desorption temperatures but also regenerative rehydrogenation at a relatively low temperature of 350 degrees C. This catalytic effect probably originates from C60 interfering with the charge transfer from Li to the BH4 moiety, resulting in a minimized ionic bond between Li+ and BH4(-), and a weakened covalent bond between B and H. Interaction of LiBH4 with an electronegative substrate such as carbon fullerene affects the ability of Li to donate its charge to BH4, consequently weakening the B-H bond and causing hydrogen to desorb at lower temperatures as well as facilitating the absorption of H2. Degradation of cycling capacity is observed and is probably due to the formation of diboranes or other irreversible intermediates.

Formation of FePt nanoparticles having high coercivity.

Ultrasonication of toluene solutions of the heteropolynuclear cluster complex, Pt3Fe3(CO)15, in the presence of oleic acid and oleylamine affords surface-capped fcc FePt nanoparticles having an average diameter of ca. 2 nm. Self-assembled arrays of these nanoparticles on oxidized Si wafers undergo a fcc-to-fct phase transition at 775 degrees C to form ferromagnetic FePt nanocrystals ca. 5.8 nm in diameter well dispersed on the Si wafer surface. Room-temperature coercivity measurements of these annealed FePt nanoparticles confirm a high coercivity of ca. 22.3 kOe. Such high coercivity for fct FePt nanoparticles might result from use of a heterpolynuclear complex as a single-source precursor of Fe and Pt neutral atoms or from use of ultrasonication to form fcc FePt nanoparticles under conditions of exceptionally rapid heating. Experiments to determine the critical experimental conditions required to achieve such high room-temperature coercivities in ferromagnetic nanoparticles are underway.