Stable and Fast Ion Transport Electrolyte Interfaces Modified with Novel Fluorine- and Nitrogen-Containing Solvents for Ni-Rich Cathode Materials.

Ternary nickel-rich layered oxide LiNi0.8Co0.1Mn0.1O2 (NCM811) is recognized as a cathode material with a promising future, attributed to its high energy density. However, the pulverization of cathode particles, structural collapse, and electrolyte decomposition are closely associated with the fragile cathode-electrolyte interphases (CEI), which seriously affect the electrochemical performances of ternary high-nickel materials. In this paper, fluorine- and nitrogen-containing methyl-2-nitro-4-(trifluoromethyl)benzoate (MNTB) was selected, which was synergistically regulated with fluoroethylene carbonate (FEC) to generate a robust CEI film. The preferential decomposition of MNTB/FEC results in the formation of an inorganic-rich (Li3N, LiF, and Li2O) CEI film with uniformly dense and stable characteristics, which is conducive to the migration of Li+ and the stability of the NCM811 structure and enhances the cycling stability of the battery system. Simultaneously, MNTB effectively suppresses the adverse reaction associated with increased polarization caused by higher interface impedance due to conventional single FEC additives, further improving the rate capability of the battery. Moreover, MNTB/FEC can effectively eliminate HF, preventing its corrosion on the NCM811 cathode. Under the synergistic effect of MNTB/FEC, after 300 discharge cycles at a high cutoff voltage of 4.3 V and a current density of 1 C (2 mA cm-2), the discharge capacity of the NCM811||Li battery was 150.12 mA h g-1 with a capacity retention of 81.10%, while it was only 32.8% for the standard electrolyte (STD). The discharged capacity of the MNTB/FEC-containing battery was about 115.43 mA h g-1 at the high rate of 7 C, which was considerably higher than that of the STD (93.34 mA h g-1). In this study, the designed MNTB as a novel solvent synergistically regulated with FEC will contribute to the enhanced stability of NCM811 materials at high cutoff voltages and at the same time provide an effective modified strategy to enhance the stability of commercial electrodes.

A Biodegradable Polyester-Based Polymer Electrolyte for Solid-State Lithium Batteries.

The low ionic conductivity, narrow electrochemical window, poor interfacial stability with lithium metal, and non-degradability of raw materials are the main problems of solid polymer electrolytes, restricting the development of lithium solid-state batteries. In this paper, a biodegradable poly (2,3-butanediol/1,3-propanediol/succinic acid/sebacic acid/itaconic acid) ester was designed and used as a substrate to prepare biodegradable polyester solid polymer electrolytes for solid-state lithium batteries using a simple solution-casting method. A large number of ester-based polar groups in the amorphous polymer become a high-speed channel for carrying lithium ions as a weak coordination site. The biodegradable polyester solid polymer electrolyte exhibits a wide electrochemical window of 5.08 V (vs. Li/Li+), high ionic conductivity of 1.03 mS cm-1 (25 °C), and a large Li+ transference number of 0.56. The electrolyte exhibits good interfacial stability with lithium, with stable Li plating/stripping behavior at room temperature over 2100 h. This design strategy for biodegradable polyester solid polymer electrolytes offers new possibilities for the development of matrix materials for environmentally friendly lithium metal solid-state batteries.

Self-Healing Binder for High-Voltage Batteries.

Lithium-ion batteries are core components of flexible electronic devices. However, deformation types, such as impinging, bending, stretching, folding, and twisting, can cause internal cracks and, eventually, damage these batteries. The cracks separate the active particles from the conductive particles and the binder, as well as the electrode from the collector. Self-healing binders can alleviate this mechanical damage and improve the stress response of active material particles during high rates of charging and discharging of these batteries and the operation at a high voltage, thereby enhancing their cycle performance. In the present study, a thermoplastic intrinsic self-healing polymer (TISP) binder is proposed. The TISP is obtained by polymerization of butanediol (2,3-BDO), propylene glycol (1,3-PDO), succinic acid (SuA), sebacic acid (SeA), and iconic acid (IA). The hydroxyl and ester groups in its structure can form diverse bonds including the hydrogen and ion-dipole with active particles and the current collector, thereby producing elevated adhesion. Its properties, including a low glass transition temperature (-60 °C), amorphous structure, and low cross-link density, improve the mobility of polymer chains at 40 °C, and this facilitates structural recovery and the maintenance of strong adhesions. Owing to its higher occupied molecular orbital (HOMO) level than the electrolyte solvent, the TISP is likely oxidized before the main component of the electrolyte during charging. This decomposition produces a chemical passivation interphase on the cathode which reduces side reactions of LiCoO2 and the electrolyte under high-voltage conditions. Tests reveal that a LiCoO2 electrode battery using the TISP as a binder retains 162.4 mAh g-1 after 349 cycles at 4.5 V, and this represents an 86.5% capacity retention. In addition, heating (40 °C, 1 h) of a scratch-damaged electrode can recover a specific capacity of 156.6 mAh g-1 after 349 cycles at 4.5 V. Relative to a battery without any mechanical scratch, this capacity recovery represents approximately 96%, and this demonstrates the importance of the TISP to the high-voltage damaged electrode.