Evaluation of ferroelectricity in a distorted wurtzite-type structure of Sc-doped LiGaO2.

Since the discovery of ferroelectricity in a wurtzite-type structure, this structural type has gathered much attention as a next-generation ferroelectric material due to its high polarization value combined with its high breakdown strength. However, the main targets of wurtzite-type ferroelectrics have been limited thus far to simple nitride/oxide compounds. The investigation of new ferroelectric materials with wurtzite-type structures is important for understanding ferroelectricity in such structures. We therefore focus on ß-LiGaO2 in this study. Although AlN and ZnO possess well-known wurtzite-type structures (P63mc), ß-LiGaO2 has a distorted wurtzite-type structure (Pna21), and there are no reports of ferroelectricity in LiGaO2. In this study, we have revealed that LiGaO2 exhibits relatively high barrier height energy for polarization switching, however, Sc doping effectively reduces that energy. Then, we conducted thin film preparation and evaluation for Sc-doped LiGaO2 to observe its ferroelectric properties. We successfully observed ferroelectric behavior by using piezoresponse force microscopy measurements for LiGa0.8Sc0.2O2/SrRuO3/(111)SrTiO3.

Suppression Mechanisms of the Solid-Electrolyte Interface Formation at the Triple-Phase Interfaces in Thin-Film Li-Ion Batteries.

Side reactions of the charge/discharge in Li-ion batteries (LIBs) generate a solid-electrolyte interface (SEI) onto an electrode surface, resulting in the degradation of the lifetime of a cell. The suppression of SEI formations has attracted much attention for achieving longer cyclable LIBs. Our research group has previously reported that few SEI were observed at triple-phase interfaces (TPIs) consisting of BaTiO3, LiCoO2, and electrolyte interfaces in LIBs with excellent cyclability and ultrahigh-speed chargeability. An investigation on the suppression mechanisms of SEI formations at TPIs should yield important information on understanding the undesirable side reactions. Therefore, we have explored the suppression mechanisms of SEI formations by preparing epitaxial thin films and evaluating the surface of the samples after the electrochemical treatment. The results of X-ray photoelectron spectroscopy and scanning electron microscopy with energy-dispersive X-ray analysis measurements suggested that the decomposition of LiPF6 was suppressed at TPIs, implying that the generation of PF5 via the decomposition of LiPF6 contributed to SEI formation.

Skewed electronic band structure induced by electric polarization in ferroelectric BaTiO3.

Skewed band structures have been empirically described in ferroelectric materials to explain the functioning of recently developed ferroelectric tunneling junction (FTJs). Nonvolatile ferroelectric random access memory (FeRAM) and the artificial neural network device based on the FTJ system are rapidly developing. However, because the actual ferroelectric band structure has not been elucidated, precise designing of devices has to be advanced through appropriate heuristics. Here, we perform angle-resolved hard X-ray photoemission spectroscopy of ferroelectric BaTiO3 thin films for the direct observation of ferroelectric band skewing structure as the depth profiles of atomic orbitals. The depth-resolved electronic band structure consists of three depth regions: a potential slope along the electric polarization in the core, the surface and interface exhibiting slight changes. We also demonstrate that the direction of the energy shift is controlled by the polarization reversal. In the ferroelectric skewed band structure, we found that the difference in energy shifts of the atomic orbitals is correlated with the atomic configuration of the soft phonon mode reflecting the Born effective charges. These findings lead to a better understanding of the origin of electric polarization.

Modulating the Structure and Magnetic Properties of ε-Fe2O3 Nanoparticles via Electrochemical Li+ Insertion.

ε-Fe2O3, a metastable phase of iron oxide, is widely known as a room-temperature multiferroic material or as a superhard magnet. Element substitution into ε-Fe2O3 has been reported in the literature; however, the substituted ions have a strong site preference depending on their ionic radii and valence. In this study, in order to characterize the crystal structure and magnetic properties of ε-Fe2O3 in the Fe2+/Fe3+ coexisting states, Li+ was electrochemically inserted into ε-Fe2O3 to reduce Fe3+. The discharge and charge of Li+ into/from ε-Fe2O3 revealed that Li+ insertion was successful. X-ray magnetic circular dichroism results indicated that the reduced Fe did not exhibit site preference. Increasing the Li+ content in ε-Fe2O3 resulted in decreased saturation magnetization and irregular variation of the coercive field. We present a comprehensive discussion of how magnetic properties are modified with increasing Li+ content using transmission electron microscopy images and considering the Li+ diffusion coefficient. The results suggest that inserting Li+ into crystalline ε-Fe2O3 is a useful tool for characterizing crystal structure, lithiation limit, and magnetic properties in the coexistence of Fe2+/Fe3+.

Enhancement of Ultrahigh Rate Chargeability by Interfacial Nanodot BaTiO3 Treatment on LiCoO2 Cathode Thin Film Batteries.

Nanodot BaTiO3 supported LiCoO2 cathode thin films can dramatically improve high-rate chargeability and cyclability. The prepared BaTiO3 nanodot is <3 nm in height and 35 nm in diameter, and its coverage is <5%. Supported by high dielectric constant materials on the surface of cathode materials, Li ion (Li+) can intercalate through robust Li paths around the triple-phase interface consisting of the dielectric, cathode, and electrolyte. The current concentration around the triple-phase interface is observed by the finite element method and is in good agreement with the experimental data. The interfacial resistance between the cathode and electrolyte with nanodot BaTiO3 is smaller than that without nanodot BaTiO3. The decomposition of the organic solvent electrolyte can prevent the fabrication of a solid electrolyte interface around the triple-phase interface. Li+ paths may be created at non solid electrolyte interface covered regions by the strong current concentration originating from high dielectric constant materials on the cathode. Robust Li+ paths lead to excellent chargeability and cyclability.